Search Documents

By Moorrees C

Carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite yields a magnesium bicarbonate leachate with a substantial soluble iron concentration. The iron concentration depends upon the leaching conditions (particularly time, temperature and pulp density) but is generally in the range 0.005-0.5 g/litre. If this soluble iron is not removed prior to the precipitation of the magnesium as a hydrated carbonate, then this product will be contaminated by the iron, and will not yield a final product (high-purity magnesia) that meets specifications.The soluble iron content of the magnesium bicarbonate leachate can be reduced to an acceptable level by addition of solid aluminium sulphate either during carbonic acid, leaching of the crude calcine or to the clarified leachate. Chemical analysis and X-ray diffraction revealed that the iron is precipitated as an iron-containing hydrotalcite-type compound, [Mg6(Al,Fe)2(OH)16]CO3.4H2O. The actual composition of the precipitate depends on the amount of aluminium sulphate added and the precipitation technique used. Because precipitation of iron in this manner also results in reduced magnesium recovery from the leachates, It WIll be necessary to develop methods for recovering the magnesium component of the precipitates.

Jan 1, 1984

THE object of this paper is to offer some suggestions to assist metallurgists to supervise the operations of flotation plants. We do not yet thoroughly understand what "flotation" is or "why minerals float" and all attempts that have been made to explain the phenomena have been based on theory or imagination, and have not been capable of substantiation by practical demonstration, or even by laboratory tests; but it is wellknown that particular minerals will float in a liquid under certain specified conditions, and that some other minerals will not float under those conditions, and that, if a mixture of the two classes of minerals be subjected to those conditions, there will be separation of the minerals, of which one class will float and the other will remain unfloated as a residue. The duty of the flotation expert is to so control the operations and the conditions of the liquor as to obtain the best commercial result from the ore he is treating. The chief controlling factors in a flotation plant appear to fall under the following eight headings, all of which are important:1. Crushing.2. Rate and regularity of feed.3. Density of pulp.4. Temperature.5. Addition agents.6. Condition of circuit liquor.7. Agitation.8. Aeration.

Jan 1, 1920

The experiments described in this paper were carried out as a preliminary to a comprehensive study of the factors which affect the behaviour of lead during and subsequent to deformation by rolling and pressing. These observations are therefore to be considered as introductory to a further paper dealing more specifically with the above-mentioned variables.EXPERIMENTALThe rolling was carried out in a small mill with six-inch diameter surface ground rolls, both of which were electrically driven at 15 r.p.m. The average draft per pass approximated 0·03 in. The pressing was performed between platens in the compression unit of a 30-ton Amsler machine. The flat faces used had a ground finish comparable with the surface of the rolls. All hardness measurements were made with a Herbert "dead load" Brinell machine. The following te'sting conditions were maintained: ball diameter-5 mm.; load-10 kgms.; duration of loading-30 seconds; temperature of testing-16 to 18°C. The hardness values which are given are the mean of two or more impressions made at corresponding positions on the test specimens.PREVIOUS WORKSince the researches of Tresca (1):j: into the nature of the plastic flow of metals during various forging and extrusion...

Jan 1, 1939

By Showers JAF

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988

By Singh RN

The Bulli Coal Seam, located in the Illawarra Coalfield of New South Wales, has a long and varied history of sudden outbursts. From available information this problem has resulted in twelve fatalities over the last one hundred and one years, with over five hundred separate outburst incidents being identified. These incidents have varied in severity and intensity from the discharge of 1 to 2 tonne of coal, with a slight increase in gas emission, to the discharge of 200 to 400 tonne of coal with some 6,000 m3 of gas being liberated and large items of mining equipment being pushed 1 to 2 metres down the roadway.Geological features associated with these outbursts can be mapped on a regional and mine by mine basis, to provide some indication or warning. Similarly changes in gas content and gas composition can also be determined on a regional and mine by mine basis. However sudden geological changes (such as a 6.5 metre seam displacement within 15 metres) variations in gas content (such as 6 m3/tonne to 15 m3/tonne) and changes in gas composition (from 95% CH4 to 90% CO2) all within one mine does make the prediction or forecasting of outburst incidents exceedingly difficult.

Jan 1, 1998

By Ormsby W. R, Nicholson P. M

Woodcutters is a polymetallic vein-style deposit hosted by sediments of the Palacoproterozoic Whites Formation which forms part of the sedimentary sequence in the central Pine Creek Geosyncline. Past production and identified resources total over eight million tonnes at 5.5 per cent lead, 12.1 per cent zinc and 110 gA silver. The local geology is influenced by Archaean basement highs; the Rum Jungle and Waterhouse Complexes. Unconformably overlying basement are interbedded clastic and crystalline carbonate units (Batchelor Group) representing cyclic changes in the depositional environment. These exhibit onlapping features with the underlying rocks. Sediments of the overlying Frances Creek Group suggest a quiet period during subsidence and subsequent increase in water depth (the carbonaceous dolomitic shales and the interbedded dololutites of the Whites Formation) followed by proximal uplift resulting in the inundation of turbiditic flows (Acacia Gap Quartzite). All of the Palaeoproterozoic rocks show evidence of being affected by penecontemporaneous, basement circling faults with steep dips. The stress regime during the deposition of the Frances Creek Group was characterised by alternating episodes of thrusting and transpression. Periods of relaxation also occurred. The compression resulted in major NS strike-slip (transpressional) faulting, en-echelon NNE trending folds and NW-SE tensional cross faults. Thrusting produced N-S striking, steep dipping reverse faults and a possible decollement immediately above the Batchelor Group. Relaxation is evidenced by the intrusion of lamprophyre dykes and dolerite sills (Zamu Dolerite). Mineralisation at Woodcutters occurred in faults within the Whites Formation, probably synchronous with deformation and the deposition of the upper parts of the Frances Creek Group. Greenschist facies metamorphism occurred as the rocks were further buried. Several massive sulphide bodies occur at Woodcutters. A number of features influence the location and shape of these bodies. They are: ò the N-S transpressional faults and in particular associated dilation zones; ò intersection of the N-S transpressional faults with the axial plane of the NNE trending Woodcutters Anticline; ò intersection of the N-S transpressional faults with the NW-SE cross-faults; ò intersection of dololutite rich units with the NS transpressional faults where local replacement takes place; ò thickening of the lithological units in the vicinity of the anticlinal axis; and ò the anticline doubly plunging to both the north and south. The mineralisation exhibits vein-like features as well as epigenetic textures. Its boundaries are sharp, its thickness varies rapidly down dip and along strike, and no alteration halo exists though stringer veins of quartz-carbonate-pyrite ¦ sphalerite/galena occur in close proximity. A number of sulphide mineral assemblages have been recognised, each separated by periods of deformation and partially replacing the earlier assemblages. Vertically continuous zonation patterns highlight the presence of rich galena-sphalerite-silver in zones of maximum dilation and pyrite-arsenopyrite-gold concentrated at the along strike peripheries. The genetic model proposed has the mineralisation occurring whilst the transpressional regime was active. It was deposited from the same fluid that elsewhere in the Geosyncline formed the stratiform deposits higher in the sedimentary pile. Hydrocarbons sourced from the organic-rich Whites

Jan 1, 1994

By A Madera, R Watt

The Tampakan deposit is a strongly telescoped high-sulphidation-epithermal/ porphyry deposit pair which is hosted by a sequence of probable Pliocene age subaerial andesite flows. These host units lie on the western flank of a deeply dissected andesitic stratovolcano within the northernmost portion of the Sangihe Arc in southern Mindanao. The deposit was discovered by WMC geologists in 1992 and is currently undergoing resource evaluation. Preliminary resource estimations indicate a total inferred metal content of 12 million tonnes of copper metal and 16 million ounces of gold. Using a 0.2 per cent Cu cut-off grade, the deposit has a current mineral resource of approximately 2.5 billion tonnes with an estimated grade of 0.48 per cent copper. At a higher cut-off grade of 0.5 per cent Cu, the mineral resource is approximately 900 million tonnes with an estimated grade of 0.75 per cent copper. Mineralisation is open both to the west and at depth. The Tampakan district is centrally located with respect to a 100 km wide zone of left-lateral strike-slip deformation represented by the trans-Mindanao Cotabato Fault Zone. The district is transected by several WNW-striking wrench faults which represent strands of the regional Cotabato Fault Zone. High-sulphidation epithermal mineralisation within the Tampakan deposit is strongly controlled by NNE-trending faults which lie along a dilational orientation within the Pliocene stress field associated with the Cotabato strike-slip fault zone. The mineralisation is broadly hosted by a gently-dipping, tabular zone of partial to massive silicification which displays multi-phase brecciation, acid-leaching, related vuggy porosity and which is developed within a district-scale advanced-argillic and argillic lithocap exceeding 90 km 2 in area. High-sulphidation epithermal mineralisation is associated with a silica-pyrophyllite-dickite-alunite-diaspore¦sericite alteration assemblage which is transitional downward to sericite-chlorite alteration and relict potassic biotite-chlorite-magnetite-anhydrite alteration associated with pervasively developed but weakly mineralised porphyry quartz stockwork veins. The high-sulphidation mineralisation is dominated by disseminated, vein and vug-filling enargite-bornite-digenite-chalcocite-covellite ¦ molybdenite which has overprinted an earlier phase of porphyry copper stockwork veins associated with high-level porphyritic hornblende diorite stocks. The distribution of high-sulphidation alteration and mineralisation reflects strong stratigraphic and structural controls. The high-sulphidation mineralisation covers a surface area of approximately 1.6 km by 2.0 km and forms a tabular, flat-lying to gently-dipping body between 200 and 500 metres thick. It is intersected at RL-1200 m ASL (at surface) in the northern portion of the deposit and extends down to RL-600 m ASL at the southern end. The deposit has been diamond-drill tested to a depth of 400 - 500 metres where low-grade chalcopyrite-bornite-pyrite mineralisation is hosted by pervasive quartz stockwork veins. This deep-level mineralisation represents the outer portion of a porphyry Cu system hosted by both andesite flows and the uppermost portions of high-level hornblende diorite stocks. Deep drilling to test for higher tenor porphyry Cu mineralisation is planned.

Jan 1, 1999

By J D. Goldsworthy

The McPhee Creek bedded iron deposit is a recent discovery made by Giralia Resources NL (Giralia) in the northern Pilbara of Western Australia. The deposit lies 30 km north of the town of Nullagine along the southeastern margin of the East Pilbara Granite-Greenstone Terrane (EPGGT).The McPhee Creek area is located in the Kelly Greenstone Belt in the southeastern part of the EPGGT. The Archaean aged greenstone belt consists of volcanic and sedimentary sequences including the Warrawoona Group and the Gorge Creek Group. The McPhee Creek iron ore deposit lies within banded iron formation (BIF) rocks of the Gorge Creek Group. The structure of the McPhee Creek area is dominated by a northeast trending, upright synform (Sandy Creek Syncline) and associated folding that is truncated by northeast trending faults in the east. Iron ore mineralisation is predominantly stratabound and follows the dip of the bedding – however, in some areas, particularly in the southwest of the deposit, mapped steep to moderate dips of bedding planes are at odds with underlying fl at mineralised zones in drill sections. Zones within the deposit that contain substantial thickness of iron ore correspond to areas of complex folding suggesting structural control and iron enrichment in fold hinges. Petrographic analyses confirm mineralisation is goethite dominant and the deposit is strongly supergene enriched.Giralia initially identified iron ore potential in the McPhee Creek area through the presence of a small known channel iron deposit (CID) mesa. Giralia began exploration in 2008 by re-drilling a portion of the CID (subsequently named Crescent Moon) and reported a small low-grade Inferred Mineral Resource. Target generation in the wider area utilising Geological Society of Western Australia maps and Ikonos satellite images identifi ed strongly ferruginous outcrops associated with major structures along an 8 km long range located 2.5 km to the west north-west of the Crescent Moon CID deposit. In late July 2008, a total of 62 rock chip samples were collected during a helicopter supported sampling program conducted at McPhee Creek. Samples taken from haematite-goethite enriched BIF and canga zones outcropping intermittently over the 8 km length of the western and central areas of the prominent range assayed up to 63 per cent Fe. These zones represent the discovery outcrops and surface expression of the McPhee Creek main range iron ore deposit.Follow up sampling, geological mapping, bulldozing of access tracks and ramps and reverse circulation (RC) drilling commenced in September 2009. A maiden Inferred Mineral Resource was announced by Giralia to the Australasian Securities Exchange (ASX) on 15 December 2009.The current Indicated and Inferred Mineral Resource at December 2010 stands at 260 Mt grading 56.2 per cent Fe, 0.12 per cent P, 6.7 per cent SiO2, 2.3 per cent Al2O3 and 9.5 per cent LOI at a 50 per cent Fe cut-off. McPhee Creek is one of the largest iron deposits found in Archaean BIF in the northern Pilbara.

Jul 11, 2011

By Littlewood E

We offer these notes as a practical contribution. All the arguments we advance have been tested by practical experience.In its preparation we realised that our subject was one of such importance and covered so wide a field that, dealt with by one of us alone, it might easily have been too much for him, so we have endeavoured, by mutual criticism and advice and a pooling of ideas, to bring forward a few points that may be of advantage to members. If any of the paper is of benefit to mining on the "Golden Mile," or elsewhere, we shall feel amply repaid for our efforts.It is obvious to all that the longer the machine is working productively per shift the greater the return, to all concerned; the machine-man himself and the company. Furthermore, if a man commences a shift with a definite objective in view; for instance, to bore and fire a specific cut, which he recognizes will give him a good financial return, then that man will exercise all his capabilities to attain that objective.In this paper we hope to demonstrate the value to the machine-man of the knowledge of the capabilities of each hole he bores, so that he will be enabled to utilize his drilling time to the greatest advantage. Also, we hope to show that such drilling time can be advantageously extended.After the war, with the influx of new men to the industry, some education on the finer points of machine work may be desirable, and any instruction in this branch must stress the realization of the value of each hole.We realise that most of those present have a sound workable knowledge of machine-mining, and we are not trying to teach anyone the fundamentals of machine work, but we would like to bring to their attentIon some of the finer points which we believe are very important.The machine-man has control of gear of a capital value of over £150, and the use or misuse of that material has a direct bearing on working costs. Therefore it is imperative that the capital outlay is gainfully employed.A "bogger" in charge of a 5/- shovel engaged unproductively is bad enough. How much worse for £150 worth of gear to be not fully productive.Figs. 1 and 2 demonstrate angles of break, and the full realization of the importance of this angle is essential to our paper. Although these Sketches are two-dimensional, we hope they will be sufficient to demonstrate our meaning. We will pass over them as briefly as possible.Fig. 1 shows three holes asked to perform an identical task.(a) 7-ft. hole bored 2 ft. into solid ground-will not come out.(b) 4-ft. hole bored 1 ft. from solid ground-will come out easily.(c) 5-ft. hole bored to solid ground-the best that can be expected under general conditions encountered.The angle of break is a right-angle, normal to direction of hole.

Jan 1, 1944

By M I. Pownceby

High temperature roasting studies on chrome-spinel contaminated ilmenite concentrates showed that sulfur, introduced through a sulfidising roast treatment, selectively reacted with the chromium in the spinels. The roast treatments were carried out in a laboratory scale rotating drum kiln using a standard Becher-style heating profile (10 h, 1075ºC), char as the reductant, and variable amounts of added elemental sulfur (0 - 3 wt per cent).After roasting, bronze-coloured grains were visible representing chrome-spinels that had undergone selective sulfidisation. SEM imaging of the products showed that sulfur was preferentially concentrated in ~5 - 15 µm thick rims fully enclosing the chrome-spinel grains. The sulfur-rich rims became a sink for manganese (Mn) from the ilmenite resulting in the rims being rich in Cr-Mn-Fe-sulfides. Quantitative electron probe microanalysis of phases present within the rims identified two sulfide phases. The first sulfur-phase (S-phase) was low in Mn (1 - 3 wt per cent) and high in Fe, Cr and S, while the second S-phase was considerably higher in Mn (30 - 35 wt per cent Mn) and lower in Fe and Cr. The dramatic change in the composition of the chrome spinels after sulfidisation is likely to significantly alter their physical properties (eg hydrophobicity, conductivity, etc). This should make their physical separation from the ilmenite potentially easier than roasting/magnetic separation methods.

Oct 5, 2011

By Q Liu

Open stoping is one of the widely adopted methods in underground bulk mining. In this method, fanned or parallel holes are often drilled from a top sill down to a sublevel in the ore zone and blasted ring by ring into a stope for excavation. A mass stope blast may involve blasting rock from multi-level drift rounds and displacing the muck to specific locations in order to allow safe and easy access for ore removal. This paper presents a strategic mass stope blast that took place at a large lead and zinc underground mine in eastern Canada. The blast consisted of more than 800 holes drilled in six blocks from three different sublevels. The challenge lay in the control of ground vibration and muck movement using precise timing to complete the blasting within 6.5 seconds. During this time span, sufficient voids were created in each level to allow the muck to move from the upper to the lower levels in sequential order across the six mining blocks without bridging. This paper describes stope blast simulations using a discrete element computer code for modeling blast-induced rock displacement as well as the application of electronic detonators. These detonators provided the means to accomplish the desired firing sequence including a drop raise blast at the start of the mass blast. The modelling concept is also described in the paper.

Jan 1, 2005

By E Hernandez, I Agustian, W Kusumohastuti

PT Freeport Indonesia is completing the first underground gyratory crusher excavation at their Deep Mill Level Zone (DMLZ) mine located in the mountains of Jayawijaya, District of West Papua, Indonesia. DMLZ is an underground block cave mine with an expected output of 80 000?t/d and a scheduled production start in 2015.In order to deliver crushed ore to the mill through the existing conveyor belt, the DMLZ block cave mine will construct two 1000?kW 1.6?×?2.3?m gyratory crushers with their own respective ore flow conveying systems underground. Each crusher is composed of top, middle, and bottom chambers with an ore bin. This system includes a series of high capacity conveyors approximately 5 km in length including transfer stations and support facilities.The development methodology required a combination of lateral development by jumbo drilling machines and vertical development by mechanised raise climbers (MRC) due to the complexity of the chamber design.This paper will discuss the project scope, design and development methodology, ground conditions, innovative survey controls, and the challenges faced due to the remote location.CITATION:Hernandez, E, Kusumohastuti, W and Agustian, I, 2014. Excavating the first underground Gyratory Crusher at the Deep Mill Level Zone mine, PT Freeport Indonesia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 43–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

By A J. Burchell

The introduction reviews the tunnelling carried out in Singapore since the early 1980s. Between 1983 and 1990, Phases 1 and 2 of the mass rapid transit system were constructed. These included some 20 km of bored and cut and cover tunnels together with 18 underground stations. Some particular points of interest in this massive project are briefly commented upon. Reference is also made to other underground or underwater schemes undertaken during this period such as the proposed large caverns project and the submerged tunnel to Pulau Seraya. A description of the subsurface works, now under construction in Singapore, follows. This includes an all underground North-East railway line 20 km long with 16 stations. At a budget of US$ 3 billion, this is a major civil engineering undertaking. Another project is the extension of the railway to Changi Airport which involves 3.5 km of twin tube tunnelling together with a major underground station which is fully integrated into the airport terminals. An on-going program of further major railway extensions over the next 10 to 15 years is in place and an outline is given of some of the most important underground sectors. Other proposed projects such as the underground roads system and the deep level sewers are briefly described. Together they demonstrate the very significant volume of underground construction scheduled for the next century in Singapore.

Jan 1, 1999

By P D. Munro

On the occasion of the 14th Mill Operators’ Conference and marking 40 years since the first one was held in Mount Isa in 1978, it is fitting to review the history of the Conference and its development over that time.The first 10 Conferences were irregularly held at three to four year intervals, with 9 of these in regional centres of Australasia. It is only since 2012 that the Mill Operators’ Conference has become a regular biennial event, alternating with the MetPlant Conference.The number of people attending the Conference has more than doubled to 470 delegates at the 13th one in 2016. It has outgrown its regional beginnings.Papers presented to the previous Conferences have been analysed according to commodity, country of origin, technology and theme plus the affiliation of the authors to discern any trends that may assist in planning the future events.Suggestions are made as to how the AusIMM might wish to arrange its mineral processing/metallurgical conferences.Recent changes to the structure of the Conference providing a more meaningful experience for the delegates and increasing their interaction and involvement should be vigorously pursued.CITATION:Munro, P D, 2018. Mill Operators’ conferences – a 40-year retrospective and a vision for the future, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 5–14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

The mineral processing industry is in boom times. The focus on mill availability and therefore profitability has never been greater, as grinding mill maintenance often dictates the entire plant shut down duration. Advances in mill systemsÆ quality and reliability and the faster, safer relining afforded by RMEÆs Mill Relining Systems have significantly enhanced grinding plant availability and utilisation. Yet relining performance is still affected by the design and planning by a team of stakeholders long before the maintenance team set foot in the mill. For a greenfield grinding plant project, these team players include: 1. project owner, 2. project manager, 3. mill supplier, 4. liner supplier, 5. plant operating personnel, 6. plant maintenance personnel, 7. mill relining crew, and  8. mill reline system supplier (RME). The complex and sometimes competing design demands of mill construction and operation together with the pressure of tight timelines can result in even simple maintenance requirements being overlooked let alone optimising plant design and planning for maintenance. This paper identifies all the involved stakeholders in an effective mill relining 'team' and gives principles and considerations for each to more effectively achieve the goals within their vital roles. This paper is aimed to be a practical guide for grinding mill designers and planners to more fully exploit the advances in Mill Relining Systems and improve their mill profitability.

Jan 1, 2008

By D Piason

Newstan Mine commenced mining operations in 1887 and has since undertaken extensive mining within the Young Wallsend, Great Northern, Fassifern, Borehole and West Borehole coal seams using a range of mining methods including board and pillar mining and longwall mining.Newstan Mine is planning to extend the existing mine workings using longwall and miniwall mining methods to produce up to 4.5 Mt/a of run-of-mine (ROM) coal for at least 25 years. The planned extension in the Main East and South West sections will involve developing new longwall panels and related mains headings. The new area contains higher specific gas emissions (SGE) than previously experienced at Newstan Mine. To achieve the optimum ventilation requirements for the longwall operation in this new area, a new ventilation shaft was designed to be constructed using the blind boring method in the South West Headings section.This paper presents the shaft design parameters and selection criteria for the construction of the new ventilation shaft, including the construction phase and the holing process to connect the shaft to the underground workings. The paper also discusses future ventilation requirements for Newstan Mine.CITATION:Piason, D, 2015. South-west ventilation shaft project at Newstan Mine, in Proceedings The Australian Mine Ventilation Conference, pp 229–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

By A Cranley, A Giblett, S Thacker

The Newmont Tanami Operations are located in the Northern Territory, approximately 550 km north-west of Alice Springs. The Granites process plant commenced operations in 1986 as a 300?000 t/a ball mill / carbon-in-leach (CIL) plant and has undergone numerous expansions between that time and the current day, with project-to-date gold production exceeding 6.5 Moz. Annual plant throughput has exceeded 2.8 Mt/a while processing a blend of open pit material and ore from the Callie Deeps underground mine, with annual gold production exceeding 400 koz. In 2013 the operation processed 1.8 Mt of underground ore for the production of 323 koz of gold.This paper reviews the operation and expansion of The Granites process plant since the mid to late 1980s with particular focus on the gravity gold recovery circuit. The Tanami ores contain significant levels of free gold, and gravity recovery has long been an integral component of the metal recovery process at the Granites plant. The results of ten years of gravity circuit performance analysis and optimisation are presented.CITATION:Giblett, A, Cranley, A and Thacker, S, 2014. Three decades of gold production at the Newmont Tanami operations, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 209–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998