Search Documents

By N N. Viswanathan, D Kumar, S Kumar

In secondary steelmaking, calcium treatment is practised to modify the solid alumina or spinel inclusions into liquid or partially liquid calcium aluminates. It has been seen that the dissolved calcium reacts with sulfur or oxygen present in the steel to form CaS or CaO type of transient inclusions. Post-calcium treatment these transient inclusions further react with pre-existing alumina or spinel inclusions and modify them. In addition, direct modification of pre-existing inclusions is also reported in the literature. In the present study, laboratory-scale induction furnace-based experiments are carried out to melt electrolytic iron in an alumina crucible followed by deoxidation with aluminium. The CaS-based composite material, prepared in-house, is added after the aluminium deoxidation to study the stability of CaS at the steelmaking temperature. Multiple steel samples were also taken to track the dissociation of CaS by means of sulfur pick-up in steel. Additionally, inclusion analysis of these steel samples was also performed to track changes in the chemical composition of inclusions in response to CaS addition. It has been seen that the CaS dissociates leading to a gradual pick-up of sulfur in steel. The scanning electron microscope – energy dispersive X-ray spectroscopy (SEM-EDS) analysis reveals that the alumina crucible and floated alumina inclusions are modified into calcium aluminates and the extent of modification depends on the contact time of CaS with the two sources of alumina mentioned earlier. However, the modification of alumina inclusions in the bulk steel did not occur during these experiments.

Jun 19, 2024

By I M. Platten

Narrow reef gold deposits are generally less than 4 m in width and relatively complex geological phenomena. They often display variable geometry, attitude, continuity and internal architecture. Economic grades are mostly restricted to specific structural domain(s) and localised within discrete ore shoots that have a nuggety internal grade distribution. On account of the often extended history of geological events, the specific factors localising gold-rich domains are likely to be unique to a particular mine or even reef. These features lead to a high resource risk and require careful management during both evaluation and mining. The gross form, location and global continuity of gold reefs can generally be determined from surface diamond drilling leading to the definition of Inferred Mineral Resources. It is likely that for the definition of Indicated and Measured Mineral Resources underground development and/or close- spaced diamond drilling will be required. Understanding geometry and continuity permits the resource to be more effectively managed, lowering risk/uncertainty. This in turn will allow for well-informed financial and operational decisions. Most importantly, project expectations and milestones can be set at achievable levels.

Jan 1, 2008

By D Morrison

Backfill is usually considered a necessary evil that contributes little to the principal objective of the operation, ore production. Consequently, it is relegated to an auxiliary role in the operation with minimal equipment and resource allocation in planning and is only superficially considered during feasibility studies. In many mines, the inadequacy of the design and operation of the backfill system ultimately leads to frequent delays, excessive costs and, in the worst cases, major instabilities which result in reduced ore production and lost or unrecoverable ore reserves. The primary objective of backfill is to prevent the progressive deterioration of mined out excavations. With the exception of narrow vein operations, it is too weak to alter the mining induced stress regime and control stress concentrations caused by stope extractions. However, the direct benefits of backfill include the possibility to consider a wider range of mining methods, recovery of 100 per cent of the planned resource and the selection of a stoping sequence that minimises the regional stability problems that cause production shortfalls in the later years of mine production. Indirectly, backfill is a practical means of solving other issues, such as waste disposal, that impact the viability of mining. In Australia, the geotechnical conditions of many mines are becoming more difficult and increased attention to the importance of backfill is warranted. This paper describes realistic aspects of backfilling and the positive impacts a well co-ordinated fill system can have on mining activities as a whole. Examples are presented where an integrated approach to backfill systems have offered significant benefits to the operation.

Jan 1, 1998

By O Aydan, R Ulusay

Blasting is the most commonly used excavation technique in mining and civil engineering applications. Blasting induces strong ground motions and fracturing of rock mass in rock excavations. Particularly, high ground motions may also induce some instability problems of rock mass and structures nearby. Furthermore, it may cause some environmental problems due to noise as well as vibrations of structures near the populated areas. Furthermore, flyrocks is another major issue for the safety of people and damage to machinery and equipments when blasting is employed. In this study, the authors explore the ways how to estimate the ground motions as a function of distance, amount of explosive, number of holes. The ground motions were measured by stand-alone accelerometers developed by the first author and some empirical relations are developed. The effect of ground motions on the instability issues of benches such as sliding, toppling and rockfalls were investigated. Furthermore, the flyrock issue is investigated and some empirical relations to estimate the maximum distance of flyrocks from the blasting relations are compared and discussed. CITATION:Aydan, O and Ulusay, R, 2018. The ground motions induced by blasting in open pit lignite mines and its environmental effects, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 142–151 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S-C Shim, H-R Lee, Y Kang, H Shin

Since iron oxide and silicon oxide are major gangue components in various types of ore, FeO-SiO2 base slag, ie fayalite slag, has been often encountered in pyrometallurgical processes of non-ferrous metals. During most matte production processes such as the smelting of Cu, Pb, and Ni, the FeOSiO2 based slag is inevitably formed and plays an important role in refining crude metal as well as engineering aspects. Recently, similar pyrometallurgical approaches have been attempted in the recovery of valuable metals (Ni, Co, Cr) from wasted secondary batteries. Thus, the viscosity of the FeO-SiO2 based slag has great significance in properly controlling smelting processes. However, when molten metal or matte does not coexist with the slag during the measurement, there has been a serious difficulty in maintaining Fe valance and consequently, the slag composition. In the present research, the viscosity of molten FeO-SiO2 slag was measured in 1573~1673 K using a rotational viscometer. In order to keep the state of iron oxides, the oxygen partial pressure was controlled using CO/CO2 gas mixture. The optimised ratio of CO/CO2 could be calculated using Fe/Fe2+ and Fe2+/Fe3+ equilibria at each temperature. The composition of the slag, particularly Fe valance, after the measurement was analysed with the aid of an inductively coupled plasma – optical emission spectroscopy (ICP-OES) and an automatic potentiometric titrator. The measurement showed that the FeO-SiO2 slag has considerably low viscosity values in the molten state, and it sharply increases as the temperature decreases. In spite of the careful oxygen partial pressure control, a part of Fe2+ was found to be oxidised to Fe3+, with a maximal case reaching about 20 per cent. The increase in viscosity of FeO-SiO2 at low temperatures can be attributed to the composition change due to an unavoidable Fe2+ oxidation. In addition, the relationship between the change in the viscosity and the liquidus temperature of FeO-SiO2 based slag was discussed to understand the composition dependence of viscosity.

Jun 19, 2024

By Brigden J. F, Birrell

A regional geochemical exploration programme commenced in July 1983, based upon low-density sampling of lateritic duricrust over parts of the Yilgarn Block of Western Australia. This resulted in recognition of an area significantly anomalous in chalcophile elements that progressively led to the discovery of the Johnston Range gold deposits in 1985. The deposits, on the Barlee 1:250,000 map sheet, occur in four mineralized zones, and production is expected to commence during 1988. The programme leading to the Johnston Range discoveries was a collaborative research/ applications study between the AGE Joint Venture (Greenbushes Ltd., St. Joe Minerals, and from 1985, Sons of Gwalia NL) and the CSIRO Laterite Geochemistry Research Group (Smith, 1987). It built upon a precursor project sponsored by Greenbushes Tin Ltd that commenced in 1980 and arose from an orientation laterite research project in the Greenbushes rare metal pegmatite district (Smith et at., 1987). Both were multi-commodity programmes and included the search for gold deposits. Basic methodologies for sampling and data interpretation have been described by Smith and Perdrix (1983) and Smith et at. (1984). Continuous geochemical coverage of designated parts of greenstone belts was sought using a triangular grid of 3-km or 1-km spacing, depending upon the expected prospectivity of the areas and the size and characteristics of the ore deposit targets. First-pass sampling, that resulted in the Johnston Range discoveries, was at 3-km spacing and several samples within a 30-km by 5-km area were

Jan 1, 1988

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010

By Smith C. B

Major diamond pipes discovered in Western Australia in the late-1970s exhibited a number of unique features that not only resulted in Australia becoming the largest diamond producer in the world in volume terms by 1986 but also changed geological thinking on the primary occurrence of diamond. They were: - lamproite is an alternative primary diamond host to kimberlite. - the extremely high mean grade of the Argyle lamproite pipe at 5 ct per tonne. - the tectonic setting of the lamproite pipes in mobile zones mar- ginal to the Kimberley Craton in contrast to the traditional African setting within stable cratons. Diamond was one of the earliest economic minerals discovered in Australia but 128 years elapsed between its first recognition and the first Australian economic pipe discovery (Argyle). During that period some 200,000 ct of alluvial diamonds were mined in Australia (mostly in New South Wales), but such alluvial output is insignificant on the world scene where annual production today runs at 95 million ct of natural stones some 76010 of which comes from primary pipe sources such as Argyle which alone produces 30 million ct per annum. Of particular significance therefore is the geological nature of the primary diamond source rocks in Australia. The Argyle and Ellendale Pipes are lamproites, differing from kimberlite in their mineralogy and geochemistry, and characterised by the presence of typical lamproite minerals such as leucite, priderite, potassic richterite, and the abnormally high content of chemical elements incompatible with ultramafic rocks. But not yet widely appreciated is that many other Australian olivine-rich lampro- phyres also contain diamond. Such picritic alkaline rocks can

Jan 1, 1988

By G J. Harbort, Z Pokra

It has been observed in several Jameson cell installations where the source for flotation feed is deslime screens, that the recovery of coal particles greater than 0.5 m is not as great as that of finer material. Consequently, a research project was undertaken at a CHPP in the Bowen Basin, Queensland, to assess the possibility of increasing the recovery of coarser particles (+0.5 mm) within the downcomer of the Jameson Cell. The effect of decreasing turbulence and agitation in a commercial-scale downcomer was investigated to assess the effect on the recovery of both coarse and fine coal particles. This paper details the findings of the testwork, summarising the results relating to differences in the operating parameters within the downcomer.

Jan 1, 2005

By N Pranoto, E Lawell, T Dean, M Grant

The Goonyella Riverside Mine is located 30 km north of Moranbah in Central Queensland, Australia. Recent mining activities have exposed the north–south striking Kenya and Zimbabwe thrust Faults. These faults vertically offset coal seams by up to 25 m and locally thicken coal packages through imbrication of coal seams. The presence of back-thrusts add to the geotechnical complexity of maintaining highwall stability. The Kenya and Zimbabwe Faults have provided multiple challenges to the mining operation, with an unplanned additional 240 kt of coal tonnes being mined from imbrication of coals seams or from the refinement to local scale geological models. These additional coal tonnes have been either identified during the mining of the coal seam or just prior to overburden removal above the coal seam. These faults can also negatively impacted highwall stability with highwall failures, lowering the overall slope angle for pit designs and increasing stand-off distances for hazardous highwall conditions. Unmanned Aerial Vehicles are used to scan exposed highwalls and enable geological mapping via high-quality 3D images. Measure while drill data from drill and blast rigs can provide local-scale intersections of the faults and coal seams. Mine Geologists utilise these and other data sets to create localised geological models refined position of the fault planes and coal seams. These models are utilised by relevant mine site teams to ensure the safe and efficient mining of coal around these faults.

Mar 22, 2022

By C Gimber

Dust suppression is an important environmental control in most mining operations. The poorest quality water within a mine site is often used for dust suppression since it provides an effective means of reducing the volume of poor quality water. The ultimate fate of contaminants or salinity associated with water used in dust suppression is important to consider for optimising water management and assessing the environmental impact and life span and maintenance requirements of roads associated with dust suppression.The propensity for remobilisation of contaminants or salts depends on a range of factors such as the application rate, climate, road construction, water chemistry and soil geochemistry. This paper describes a typical study approach which could be used to assess the short- and long-term impacts of mine water application for dust suppression. The steps of the study are: reviewing the environmental setting, estimating water requirements for dust suppression, reviewing source water chemistry, developing a mass balance model and assessing the mobility and fate of contaminants with a geochemical model.This approach identifies which salt species are likely to form and whether they are prone to remobilisation. It is possible to quantitatively assess the risk of exporting contaminants or salt from roads and to refine the dust suppression strategy to minimise the environmental risk. The approach can be applied at mine sites to address regulator concerns, aid decision-making and improve the understanding of short- and long-term environmental risks.CITATION:Gimber, C, 2013. Assessing contaminant risk associated with the use of mine water for dust suppression, in Proceedings Water in Mining 2013 , pp 235-240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

The OK orebody comprises a steep dipping narrow quartz reef averaging 0.4 m in width hosted in basalt and gabbro with porphyry bars cross-cutting through it. The following paper tracks the mining of this orebody, challenges encountered, measures undertaken to address these challenges and changes in mining conditions and methods as the mine matured in both depth and age. The initial mining method was narrow vein hand held shrink stoping accessed by shaft, that over the period of the mines life was superseded by gallery stoping, shrink stoping and ultimately mechanised narrow vein long hole sublevel open stoping. The reasoning behind the change in mining methods is detailed, including safety and cost benefits. The transition presented many challenges that were overcome, resulting in the successful development of a narrow vein long hole stoping method. The lessons learnt during the transition period and the practices and principles developed for successful mining of narrow vein orebodies using long-hole open stoping methods are summarised in this paper. The final section of the paper takes a retrospective view of how the knowledge gained through the mining of the OK orebody would be applied to a new mine containing an orebody of this type, with consideration given to the initial excavation design, equipment selection, mining sequence, geotechnical investigations and mining method used.

Jan 1, 1998

By N Donnellan

The Palaeoproterozoic Warramunga Formation is notable as the host to the enigmatic, so-called 'Tennant Creek style' mineralisation. These polymetallic (but mainly Au-Cu-Bi) ore deposits typically have a close spatial association with massive ironstone bodies, and frequently also with banded ironstone, known locally as 'haematite shale'. The Warramunga Formation is a polydeformed, turbiditic succession. Partial, or complete Bouma sequences variously comprising lithic arenite, wacke, siltstone, and mudstone constitute a classic flysch sequence deposited as a proximal (sandstone lithofacies) to distal (siltstone lithofacies) fan association. The Warramunga Formation has a substantial component of volcanic detritus and has generally been attributed to an essentially contemporaneous volcanic provenance. However, lithostratigraphic revision (Donnellan, Hussey and Morrison, in press) apparently precludes outcropping volcanic rocks of the Tennant Creek Block, or indeed Inlier, as the source of detritus. Warramunga Formation geochemistry indicates rapid derivation from a fractionated, predominately felsic igneous source (Palaeoproterozoic upper crust) with a minimum of chemical weathering; together with an admixture of mafic material. Warramunga Formation geochemistry cannot, however, be reconciled with that of the Bemborough Formation, which is here taken to be representative of Flynn Subgroup felsic volcanic rocks. Similarly, the Warramunga Formation is geochemically distinct from Flynn Subgroup sedimentary rocks. Geochemistry of the banded ironstone is consistent with its interpretation as Dine-grained turbidites.

Jan 1, 1994

By S Karosiya, A Sharma, M Jain, N N. Viswanathan, M M. Pande, D Kumar, S Kumar

Desulfurisation of steel during ladle refining is governed by both thermodynamics and kinetics. For effective desulfurisation, thermodynamically, a low partial pressure of oxygen at the steel-slag interface and highly basic slag which possess a large sulfide capacity are desired. Kinetically, the mass transfer coefficient of sulfur in the liquid steel and in the slag determines the rate of desulfurisation. A fast desulfurisation rate is achieved by maintaining sufficiently strong argon stirring of the melt. In the present work, sulfur mass balance for steel and slag was performed after the desulfurisation treatment for several industrial heats. The decrease in the sulfur quantity of the liquid steel was more than the increase in the sulfur quantity of the slag. The discrepancy in the sulfur mass balance suggests that the sulfur could be transferred to: (a) the gas (via slag) phase; or to (b) the refractory (crucible) phase. The preliminary investigation of the refractory samples taken at slag-refractory and steel-refractory interface showed no interaction of sulfur with the refractory. Therefore, the possibility of sulfur transfer to the gas phase was verified by carrying out melting experiments of sulfur containing slag in an argon/air atmosphere. Sulfur containing slag was initially melted in an MgO-C crucible under an argon atmosphere followed by creating the air atmosphere just above the melt. Careful sampling and analysis from the cold spots of the crucible, much above the melt surface, revealed formation of a fibrous structure. Scanning electron microscopy energy dispersive X-ray spectroscopy (SEM-EDS) analysis of these fibrous deposits confirmed the presence of oxides and sulfides. Oxidation of sulfur containing slag under air atmosphere was also performed using a thermogravimetric analysis (TGA) set-up. It showed a constant sulfur loss in the range of 1300– 1500°C. Thermodynamic calculations carried out using FactSage™ ver 8.3 for these experimental conditions are in good agreement with the observed results.

Aug 21, 2024

By Z Li, Z Yan, T Htet, S Zhang

During the pyrometallurgical processes, a substantial quantity of high-temperature ironmaking and steelmaking slags, generated at temperatures ranging from 1400 to 1600°C, is wasted, as the heat contained in these slags is released into the environment during the tapping process without effective utilisation. On the other hand, a significant amount of energy is required to reheat the cold materials for the manufacturing of glass and mineral-wool, often necessitating the addition of high-silica materials to facilitate the production process. In this study, an innovative approach is presented to harness the heat present in molten metallurgical slags to directly produce new raw materials for glass and mineral-wool manufacturing while simultaneously reducing energy consumption and mitigating CO2 emissions. The theoretical amount of waste glass that can be effectively added in the process has been estimated via thermodynamic calculation. Experimental assessments were conducted to examine the impact of high-silica waste materials on the dissolution, melting and fluidity. Potential recipes for glass and mineral-wool manufacturing were suggested and an assessment of the energy savings, and reduction in CO2 emissions with manufacturing of glass and mineral-wool using this innovative approach were included. It was determined that the processes could lead to a reduction of over 26 kg of CO2 emissions per 100 kg of new material used, primarily due to the utilisation of heat from slag and the accelerated smelting process.

Aug 21, 2024

By J Coveney, A Rich, D Grimsey, J Wood, S Creedy

In 2021, BHP and Metso examined processing of high-MgO nickel sulfide concentrates using Metso’s Ausmelt Top-Submerged-Lance (TSL) technology. Test work was conducted in Metso’s pilot test work facility in Dandenong, Australia to explore operability of the SiO2-FeO-MgO-CaO-NiO slag system across a wide range of compositions, temperatures and bath oxygen potentials. Pilot-scale testing aimed to define slag ‘operability limits’, representing the lowest bath temperature at which stable process and equipment operation could be maintained. This work was supported by FactSage™, version 8.2 (by Thermfact/CRCT and GTT-Technologies) thermodynamic modelling, slag viscosity measurements, physical characterisation of quenched slag samples performed by the University of Queensland and benchmarking of commercial-scale TSL nickel smelting operations. A wide range of slag compositions were examined, with Fe/SiO2 ratios varying from 0.4–1.1, CaO content from 0.8–7.0 wt per cent and MgO content from 6–19 wt per cent. Slag SiO2/MgO ratio, wt per cent CaO and matte grade were found to have the greatest impacts on identified operability limits. Operability limits were found to be influenced by both the solids content in slag and viscosity of the remaining liquid slag phase, with the relative contribution of these parameters heavily influenced by the slag composition. In the majority of trials, limits were defined by a theoretical solids content of 40–50 per cent, however in trials with a low Fe/SiO2 ratio and/or low wt per cent CaO, limits were characterised by a much lower solids content due to the increased effect of the liquid slag viscosity in determining the behaviour of these slags. The test work highlighted inherent flexibility of the Ausmelt TSL process to operate across a wide slag range of slag compositions and recover from process disturbances without an interruption to feeding. The trials also demonstrated the possibility for Ausmelt TSL technology to process concentrates with an Fe/MgO ratio as low as 1.4, which has important implications to the commercial-scale processing of high MgO feeds. Arsenic rejection across the trials was very good, with only 30 per cent of arsenic in the feed inputs reporting to the matte phase. Such high levels of arsenic removal provide the Ausmelt TSL process with a notable advantage over alternative smelting technologies.

Aug 21, 2024

By M Francoeur

Oct 12, 2022

By M Jahani, M Taji

For suitable production planning in an open pit mine, and also to carry out the optimisation process during the mining production cycle, prediction of fragment size distribution is required prior to carrying out the blasting operation. For this purpose, many prediction models, such as empirical models, were presented. The proficiency of these models differs in various conditions and mines. Therefore, in this paper the most important models, including SveDeFo, Kuz-Ram, CZM, Modified Kuz-Ram in 2005, Kuznestsov-Cunningham-Ouchterlony (KCO) and also Gheibie et al, were examined by the information of 20 blasts in Gol-Gohar iron ore mine. Fourteen images were taken on average for each blast. For image processing analysis Split-Desktop software was used. After examination, it was understood that none of the available empirical fragmentation models had presented acceptable performance, except the Kuz-Ram model for magnetite ore, which had somewhat acceptable results. However, this model for blasting patterns in hematite presented unsuitable results. Examination and comparison of two important distribution functions, Rosin-Rammler and Swebrec, were carried out and it was observed that the performance of Swebrec for fines was far better than Rosin-Rammler. This result for the upper part of fragment size distribution curve, coarse, is the reverse.CITATION:Jahani, M and Taji, M, 2015. Comparison of empirical fragmentation models at the Gol-Gohar iron ore mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 707–714 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G N. Phillips

No new goldfields have been found in the Witwatersrand Basin for over 60 years, and one consequence of this is a long-term decline in gold production. Exploration throughout this period has been based on the placer model that infers alluvial transport of gold grains and then sedimentary sorting in the basin; however, there is no viable source for so much alluvial gold and no single sedimentary setting that hosts the gold.An alternative genetic model can now provide a quantified explanation for the source of the gold, and it does not rely on alluvial gold processes. The hydrothermal model can easily explain the source of the Witwatersrand gold as being derived from the background gold at parts per billion (ppb) level throughout the Kaapvaal craton of South Africa. This gold is involved in metamorphic processes, available for solution in metamorphic fluids, and hence may be transported whilst dissolved in fluid into the Witwatersrand Basin. The hydrothermal model warrants consideration as it can explain the source of gold, the large alteration halo in the goldfields, the mineralogy, and especially the gold-carbon association.Working on the premise that if one model (placer) is not giving the desired results (discovery of new goldfields), then it may be prudent to consider alternatives. Application of a hydrothermal model to guide exploration would place importance on large and small early structures in and around the Witwatersrand Basin; it would also emphasise the geochemical nature of potential host rocks (especially C and Fe) rather than their sedimentary origin.CITATION:Phillips, G N, 2013. Origin of Witwatersrand Gold - a viable source region and source process for gold, in Proceedings World Gold 2013 , pp 175-180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

The Kwademen Au deposit was discovered in 1977- 1978 following a regional geochemical survey carried out as part of a UNDP (United Nations Development Programme) and BUMIGEB (Bureau des Mines et de la Geologie du Burkina) mineral exploration programme. The climate in Burkina Faso is rather dry, with markedly seasonal rainfall averaging 800 mm pa in the Kwademen project area. The relief is low and the drainage poorly developed, so that soil sampling was preferred to stream sediment sampling. Rocks have been subjected to deep lateritic weathering, so that they are transformed into a mixture of Fe-oxides and kaolinite over depths varying between 30 and 40 m. At the regional stage, soil samples (30-40 cm depth) were collected a a 300 x 500 m grid. The Kwademen deposit was indicated by Cu, Zn, Mo and Au anomalies. Subsequently, an area of 9.2 km2 was covered by a detailed geochemical survey by soil (100 x 50 m) and auger sampling. The regional anomaly was fully confirmed, and subsequent drilling intersected mineralized ore shoots, justifying the establishment of an evaluation project led by the U.N.R.F. (United Nations Revolving Fund) in 1983- 1985.

Jan 1, 1988