Search Documents

By M E. Trim, J J. Johnson, W Cranston

The Brightwater conveyance system is located near Seattle, Washington in the north-western United States. The East Contract portion of the system consists of a 4.3 km long, 5.9 m diameter tunnel in soft ground and two large shafts constructed in challenging soil conditions. The two shafts are situated side-by-side in an urban valley. One will house an influent structure to direct incoming sewage and outgoing treated effluent, while the other will house a 645 megalitre per day (ML/d) influent pump station. The tunnel contains four pipelines: two force mains to convey untreated wastewater eastward from the new pump station to a new treatment plant, one gravity-pressure pipeline to convey treated effluent westward to a new outfall in Puget Sound, and one high-pressure pipeline to convey reclaimed water from the treatment plant to downstream distribution points. The shafts and the tunnel presented many design challenges. Groundwater is near the surface in the area surrounding the shafts, and compressible peat and clay soils preclude dewatering during construction. These and other challenges were encountered during design of the pump station shaft and multiple-pipe tunnel. The challenges were addressed by a design that includes a dual intersecting circular cell shaft (referred to as æthe peanutÆ) and a single tunnel into which stacked pipes will be æstuffedÆ. This paper discusses the design approach and design details for both elements.

Jan 1, 2008

By Rosenblatt M, Gilroy J. A C Cunningham C V B

Vaal Reefs Exploration and Mining Company Limited operates one of the largest producing gold mines in the world. The annual production of 76 tons of gold from 12 million tons of ore treated is obtained mainly from underground sources. Daily some 6.6 km of stope face is blasted and 41 tons of explosives is used to break the rock. The mine employs 45 000 men of whom 35 000 work underground. The company operates nine large vertical shaft systems of which seven extend more than 2000 m below surface and an eighth, currently being sunk, will bottom at 3700 m below surface.

Jan 1, 1995

There are many variables in a flotation concentrator, some of which are outside the actual flotation stage, which affect metallurgical performance. The number of such variables which can now be measured on a continuous basis has increased significantly over the past 20 years. They can be broadly classified under the headings of physical, chemical, and elemental. In this paper reference is made to a number of such variables, and comment is made on the state of the art in their measurement. Although not confined to development in Australia, particular reference is made to the considerable Australian contribution in this area of Technology.

Jan 1, 1984

Underground mining in the West Moreton coal field started in the 1870's. Subsidence related to coal mining activities is an ongoing problem facing planners and developers in the Ipswich area in South Eastern Queensland. The history of coal mining in the area over the last 110 years has left the legacy of periodic surface instability in several areas. In general, modern engineering analysis with current mining methods combine to create predicatable analysis of surface stability and movement. Where old workings using several variations of the bord and pillar system are affected by current activity, the predictibility of the surface movement is greatly reduced. Geological complexities further complicate the analysis. Mining and the related dewatering affects the stresses on pillars in old workings. This is caused by reducing buoyancy effects caused by changes in the water levels in old workings. Of particular relevance is the depth of workings and strength of the coal and overburden. The type of subsidence affecting the surface can range from localised pillar failure, to roof failure and potholing and the likelihood of the particular form of subsidence can be assessed from studying the workings in relation to the stratigraphy and structure of the coal measure Formations.

Jan 1, 1988

By Thomas CG, Armstrong GJ, Lynch KS

A small glass walled pot grate has been used to simulate drying of iron ore pellets in a travelling grate plant. This equipment has enabled the effect of decreasing grind and de- creasing pellet bulk density on plant production to be quantitatively predicted. These predic- tions are compared with plant experience. The use of the laboratory simulator in comparing the effect of various additives on plant production is also described and substantial improvements in both the goethite and free-water drying periods are predicted.

Jan 1, 1972

The theory of declining optimimum cut-off grades is more than 25 years old, but for a number of reasons it is still not widely used in industry. A lack of faith in the veracity of estimated grades is not in itself a reason to abandon any attempt to optimise cut-off grades. The use of declining cut-off grades has been thought to cause high-grading, but in fact this is only true if an artificially high discount rate is used in the calculations. Perfect application of an optimum cut-off grade should ensure that only ore generating more than a minimum net return is mined, and that as much as possible of the ore capable of generating that return is mined. Therefore differing mining costs in different parts of some underground mines necessitate local modifications to cut-off grade. Optimisation of cut-off grade is of necessity an iterative process. Integration of that process into a feasibility study need not be excessively time-consuming. A number of approximations can be made to speed the optimisation (any attempt to achieve a high level of accuracy is probably doomed to failure by a lack of precise cost and price projections). A procedure is outlined for optimising cut-off grade during planning of a typical underground mine.

Jan 1, 1991

By Dight P. M

The challenge of narrow vein mining is to produce ore with as little dilution as possible, at the least cost -commensurate with the increasing degrees of safety being demanded for mine workers by the modem 'duty of care' legislation. Geotechnical factors play an important, if not overriding, role in these areas. The geotechnical factors cover the complex interaction over a period of time, between the in situ and induced rock stresses, rock structures, rock mass strength and the cable, rock bolt and other ground support members. In the Archaean schist belt areas where many of our narrow vein mines occur the pre-mining in situ rock stresses are commonly significantly higher than the overburden stresses. These are concentrated in areas beneath previous open pits and may be highly concentrated in the pillars and abutments of stopes on narrow veins. The presence of high in situ stresses may be suspected from the appearance of drill cores and underground development long before they become sufficiently concentrated by mining to cause damage or bursts. These initial indications are discussed and modem low cost methods of stress measurement are described. Practical and quick methods of analysing the stress redistribution around scopes and other underground excavations are now available and guidelines for interpreting them in terms of rockmass characteristics, stope stability and support requirements are developed with the object of increasing safety, whilst reducing overall costs and dilution.

Jan 1, 1993

By Monette J. C, Nulty J. H

High temperatures and pressures are required to obtain acceptable stripping rates. Higher chemically induced stripping rates could reduce the need for higher temperatures which lead to cyanide losses. The higher rates could lead to lower carbon inventories and higher gold production. This paper reports laboratory and continuous test unit data which strongly suggest that the preceding can be achieved. New stripping agents demonstrate efficient stripping under conditions of cyanide depletion such as after carbon acid washing. Stripping times for gold and silver can be reduced by at least half compared to caustic cyanide through the use of these novel substances.

Jan 1, 1991

By Ghose AK

Design and selection of support systems for longwall faces call for in-depth know- ledge of strata mechanics and in particular of strata-support interactions. The paper presents the results of field investigations and analysis of a difficult-to-cave roof using powered supports under a massive dolerite sill in Central India using a state- of-the-art datalogger system. The mechanised long wall face was equipped with 4/680 tons chockshields operated on the IFS mode using a 300 KW DERD shearer. The datalogger system was capable of storing data simulta- neously in 32 channels. The paper describes the monitoring system and the monitoring programme. The system provided useful information on support behaviour, build- up of leg pressures and face convergence during an intense dynamic periodic weighting phenomenon which destroyed the integrity of almost half of the face supports. At this point, the face had advanced by about 197 metres from the barrier. The paper outlines a post-mortem analysis of this dynamic event and provides a critical evaluation of the data collected for understanding strata support interaction and the behaviour of the massive sill in the overburden.

Jan 1, 1992

Underground space can be defined as space below natural ground level which can be used as an alternative to an above ground location. While many of our above ground structures inherently involve underground excavation for foundations and services, the term underground space specifically refers to organised development of underground openings and of the underground domain. For example, the services to a city such as power, gas, sewerage, water and communications are installed in a congested array which usually requires roads to be dug up when the services need to be accessed. An underground space installation of services would involve a well planned conduit which is easily accessed without any excavation. The concept of using this virtually untapped land resource to the advantage of our expanding cities is gaining considerable interest in Australia. Overseas, in the Scandinavian countries and some Asian countries, underground space has been used for centuries; in Great Britain, France and the United States of America over the last century and in Japan for over a decade. This paper focusses on the types of underground space usage which should be competitive with above ground use and suggests areas in which the competitive edge may be improved in favour of underground space. In particular, considerable advantage is seen by using well-planned underground space developments in major cities, where the strategic central location of the development takes advantage of proximity to potential users. However, the largest single factor affecting the acceptance of underground space is the high capital cost of construction, even though an underground space development may result in lower operating costs and reduced long-term maintenance costs. While excavation methods and associated costs are very much site-specific, the importance of applying the latest technology in rock breakage, with consideration of ground vibration, excavation rates and ground support, remains a major challenge to the development of underground space.

Jan 1, 1995

The paper describes the studies conducted to date on the short term adsorption/desorption of gases in coal from the point of view of developing techniques to predict imminent outbursting conditions in coal mines. A number of different parameters such as'dP express, K' and AV 0/60 etc. which have been effectively used overseas were studied on samples of coal from Westcliff and Leichhardt Colliery. Results indicate that these do not seem to be valid indices for predicting an outbursting condition. Based upon desorption isotherms, a new index defined as "L" has been developed which shows promising results. This index is in a position to differentiate the changes in the structures of coal and its proness to outbursts. The "LZ value determinations and its usefulness opens a new field where it would be possible to determine outbursting conditions from existing drill cores obtained during exploration studies or from long holes drilled in advance from underground workings. The index is more or less independent of the time elapsed between the extraction of a sample and the conduct of the test. The test for "L" can be conducted'on site or in the laboratory. The test is simple, easy to carry out and the "L" value for a sample can be calculated in less than 20 minutes. It could be adapted as a routine test for monitoring outburst conditions in mines.

Jan 1, 1980

The subject of heat sources in deep hard rock mines, the limitation of forced ventilation to cope with these heat loads and the sizing of refrigeration plants to boost the cooling effect of the ventilation air are discussed. The development of plant selection criteria and operating experience at North Broken Hill Limited is outlined. Future options for North Broken Hill Limited and like deep mines are summarised.

Jan 1, 1982

By OÆNeil G. R

The gold adsorption capacity of ash-char and ion exchange resin Zerolit F.F. (I.P.) was evaluated by obtaining Freundlich isotherms in the presence of selected variables. It was found that the presence of Na , 2+, Ca 2+ cations and SO4 , CN , S Z, 0 2- Zn anions prompted adsorption of gold onto the char and reduced gold adsorption capacity of the resin. Temperature, particle size of adsorbent and pH of solution were found to influence the gold adsorption capacity of char and the resin. The most efficient desorbent for gold adsorbed on the ash char was S2 ions. Optimum sulphide concentrations were found in the region of 1% Na2S. Investigation into the concentration of gold from actual carbon contaminated gold residue dumps in Kalgoorlie area onto ion ex- change resin showed limited success in one case and not so in another. Maximum gold adsorption by the resin appeared when cyanidation and sulphidization treatments were carried out simultaneously in the presence of the resin.

Jan 1, 1979

By Bartosiewicz H

A method for the determination of the gas content of coal seams is presented which improves upon existing methods. The method makes use of a gravitational technique for measurement of the gas desorbed. The amount of lost gas is estimated by determining an empirical relationship relating the desorption of gas with time for each sample separately. This is to replace the assumption that desorp- tion follows a square root law with time. Laboratory investigations have been conducted which indicate that the square root desorption law does not hold good for carbon dioxide. Results of investigations on various factors influencing the technique are presented. It is shown that co-efficients of the empirical equation are dependent upon the elapsed time and the period of observation. Data about gas pressure measurements is presented and it is concluded that gas pressure can be approxi- mated to 0.6 times the pressure below a column of water equal to the depth of cover. This estimate is good enough for adsorption tests to evaluate desorption co-efficients. The technique for repressurisation of the sample,

Jan 1, 1982

Thirty six different commodities were recorded from 3708 mineral occurrences in the Atherton 1:250 000 Sheet area, mapped by personnel of the Queensland Department of Resource Industries. Tin, occurring in 56% of all mineral occurrences, is the most common, followed by copper, tungsten, silver, lead, gold, fluorite molybdenum, zinc and antimony. The densest area of mineral occurrences is the Herberton Mineral Field, one of the most intensively mined areas in the state.The majority of occurrences in the sheet area are fracture, fault or shear related vein or lenticular deposits, with subordinate types being pipe, skarn, endogreisen, disseminated and porphyry copper deposits. However the larger mines in the area are commonly of the subordinate types including the Red Dome gold-copper skarn, the Wolfram Camp and Bamford Hill tungsten- m olydbenum endogreisens, and the Vulcan pipe tin deposit. Significant gold prospects occur in quartz-antimony veins, breccia pipes and skarn deposits associated with rhyolitic porphyry dykes. A fluorite-gold association has been noted in several areas on the western side of the sheet.Mineralised fractures are predominantly oriented in a NNW direction which is the major trend in the Hodgkinson Province. Secondary N and NE directions are also present.

Jan 1, 1990

In the new refinery, at the works of the Broken Hill Associated Smelters Proprietary Limited, situated at Port Pirie, South Australia, the refining routine is similar to that carried on in the old one in that bullion is progressively refined first for arsenic and antimony, then for copper and gold, then for silver, and finally for zinc. However, actual procedure differs in that each refining operation is now conducted continuously, whereas in the old refinery intermittent batch treatment was practised.The early experimental work was concerned solely with the development of the continuous desilverising process, which, in addition to continuous treatment, embraces the novel feature of conjugate solution formation with consequent production of a silver product relatively high in silver and low in lead.

Jan 1, 1932

Optimising drill performance has always been a primary goal of drilling and blasting managers. Improving drilling rates and utilisation will ultimately drive the cost per foot or metre downward. Additionally, more consistent production will ensure shovel or dragline performance goals are met and the chances of machine idle time is minimised. Over the past 20 years, many studies have examined rotary drilling factors and performance issues. In most cases a common theory points to energy input versus drilling output. Indexes such as specific energy and total work energy have been -developed to quantify the drilling process. As general engineering principles dictate, energy is required to drill rock by overcoming compressive and shear strengths. Concurrently, the greater the energy input, the faster the penetration output. Therefore, by examining the basic drilling energy parameters, optimisation is possible. The principles of rotary drilling are driven by five factors. When optimised individually and as a system, drill performance will improve. Most recent studies all agree that a performance relationship exists between bit load, bit rotation, and hole flushing. Additionally, proper bit selection and most of all, the operator, can have a tremendous effect on drill productivity. By analysing these factors and establishing the best case scenario, an overall drilling system can be engineered to match the mining characteristics. Furthermore, by balancing these factors, a lower cost will be achieved through increased production rates, maintenance costs, and effective drill utilisation.

Jan 1, 1995

Krupp Polysius AG, FRG, in close cooperation with Prof. Dr. K. Schoenert, FRG have developed the principle of the high pressure grind- ing roll POLYCOM. The POLYCOM mill basically consists of two counter-rotating rolls of large diameter and relatively small width, one of which is fixed and the other moving in slide blocks. The pressure required for comminu- tion is applied via the sliding roll by a powerful hydraulic system. The comminution takes place between the rolls under high pressure in the bed of material by nipping and compacting. The top feed size-depending on the rolls diameter -may be as coarse as conventional secondary crusher feed and the product is a compacted cake containing a high amount of fines created by micro-cracking. The amount of fines depends on the pres- sure (grinding force) applied. Operating results show that even in wet griding circuits capacity increases at downstream connected grinding mills of up to 100010 can be accomplished with an interconnected POLYCOM machine and energy savings of up to 25070 may be achieved depending on application. POLYCOM can be used in existing grinding plants for low-cost upgrad- ing of capacities but also as an advanced alternative to conventional crush- ing and grinding equipment in open or closed circuit configuration. A single industrial size 2.8m roll diameter POLYCOM machine may be fed with top feed size of up to 200mm and produce a finish product as fine- grained as known from rod and ball mills but with less energy consumption. Meanwhile, the POLYCOM high pressure grinding roll has established itself world-wide in the cement industry and is now entering the mining industry. POLYCOM machines are currently designed in industrial standard sizes of 1.0m to 2.0m rolls diameter and drive units of up to 2400 kW. This paper includes: principles of high pressure grinding, main fea tures of the POLYCOM machine, results of tests on various materials including Australian gold and copper ores carried out at the POLYSIUS research centre in Germany. Some examples of industrial applications of high pressure grinding will also be presented.

Jan 1, 1988

By Bevan JE

The US Bureau of Mines is conducting research to improve the health and safety for underground coal miners, and the efficiency of the mining systems that are used. In 1986, the Bureau began a major research effort on the technology for computer-assisted mining systems for underground coal mines. The initial target was technology for continuous mining machines that would allow them to extract coal by computer-assisted operation. Technology areas being investigated include guidance systems, machine condition systems, computer systems, machine control, human-machine interfaces and planning. In each of these areas, individual system development has progressed to where underground testing of these systems will begin in 1991.In addition to coal extraction, the Bureau has also begun research for the development of technology for computer-assisted roof bolting. The Bureau is developing technology for a "smart" roof bolter that would be able to sense and analyze strata conditions to determine the requirements to provide a competent roof. The system would determine the location of the hole, drill the hole to length, and select and install the appropriate bolt.

Jan 1, 1991

By Swift J. D

A key parameter affecting the performance of gravity thickeners in hydrometallurgical processing operations is the aggregation state of the feed after the addition of a flocculant. New procedures which measure the settling ratelsize relationship and the size distribution of aggregates in their process liquors have been used to quantify the aggregation state of the feedwell, overflow and underflow streams in a tailings thickener. The data obtained have been related to the thickener's operation and to a change in the flocculant dosage. A comparison is also made between the settling rate/size relationships determined with these new procedures and the mud-line settling rates from cylinder tests.

Jan 1, 1991