Search Documents

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are steel-based, thin-walled tubular ground reinforcement widely used in underground mines in Western Australia. Following installation these stabilisers are subject to corrosion which may reduce the load carrying capacity and lead to unexpected ground falls. Although corrosion has been recognised as a common occurrence, particularly under aggressive mine water and mineral conditions present in underground mines, the knowledge of the effects of corrosion on the mechanical behaviour of FRS is limited. The Department of Minerals and Energy of Western Australia has conducted a laboratory based program of studies to investigate the effect of corrosion on the mechanical properties of FRS. The studies have focused on the effect of corrosion on tensile strength of FRS and frictional resistance along the interface between FRS and the drillhole wall. The results indicate that under certain conditions corrosion damage can significantly reduce the effectiveness of FRS.

Jan 1, 1996

By Nemcik JA, Gale W. J

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ

Jan 1, 1992

The activiltion of sphalerite with electrolytically generated copper ions from a copper electrode instead of the usual practice of the addition of copper sulphate was studied in the laboratory. A large surface area of copper was provided by lining three sides of a bench flotation cell with copper sheeting. The lining was connected to the positive terminal of a low voltage d.c. source, and the cell impeller to the negative terminal.Sphalerite was effectively activated by this arrangement and was subsequently floated using xanthate as the collector.Flotation results comparable to those obtained with 1 lb/ton CuS04.5H20 (0,255 lb/ton copper) were obtained using 0·1062 lb/ton of electrolytic copper and 0·488 kWh of electrical energy. The wastage of copper due to the formation of insoluble precipitates was found to be dependent on the length of time the current was passed. Maximum current was passed for the shortest time to minimize wastage.

Jan 1, 1973

Structural Controls Interpretation of regional aeromagnetics, radiometrics and satellite image data has identified three structural domains (fig 2): The Fairyland Domain: a general N - S structural trend. The Cracow Domain: a general NW - SE structural trend. The Bald Mountain Domain: a general N- S structural trend. Known mineralisation is confined to the Cracow Domain in which there occurs two major NW - SE trending fault zones. The Cracow Fault Zone (CFZ) and the Immy Creek Fault Zone (ICFZ). Enhanced detail of the CFZ (fig 3) shows three main structural trends within it: NW-SE structures which include the mineralised White Hope South fault zone and the Golden Mile fault zone. NE-SW structures which have an influence on mineralisation in the Orange Creek, Fernyside and Golden Plateau areas. N-S structures comprising several major structural zones.

Jan 1, 1990

The Carnilya Hill Mine, a joint venture project between Western Mining Corporation Limited (WMC) and The Broken Hill Proprietary Company (BHP), is a nickel sulphide deposit being developed by the Kambalda Nickel Operations (KNO) of Western Mining Corporation. Seven months elapsed from the time a decision to proceed with the project was taken until the first ore production. During the first month of operation a new KNO record for decline development was set. Equipment used includes an electro- hydraulic drill jumbo, 4 cubic metre front end loaders, and 35 tonne haulage trucks.

Jan 1, 1981

Initial coal production at Ulan was solely from underground mines. A significant increase in demand for steaming coal in the late 1970's emphasised the need to further expand production and led to the development of the open cut mine which commenced commercial production in June, 1982.During the initial stages of mine planning, feasibility and cost studies were undertaken to determine the most suitable method for coal haulage from the pit. The comparison between a conventional truck haulage system and an in-pit crushing system using a mobile crusher and moveable belt conveyor haulage confirmed that the mobile crusher and conveyor system was superior in every respect for the Ulan mining operations.Technical features and design parameters for the major items of equipment are outlined as well as operating, manning and performance assessments. Minor equipment problems were encountered during initial operation but these have since beenrectified and the plant is now capable of exceeding the design production. Maintenance and energy costs are considerably lower than originally estimated and production efficiencies are continually improving as operators develop new techniques and procedures in the handling of the equipment.

Jan 1, 1985

The mineralogy, maero- and micro-textures of Thackaringa ore are simple and have many counterparts among base metal-quartz-siderite vein type deposits elsewhere.The ore consists predominantly of galena, sphalerlte, chalcopyrite, tetrahedrite, and arsenopyrite in a quartz and siderite gangue. Silver minerals, as such, appear to be lacking and silver values are no higher than in other sulphide ores of this type. These features contrast very markedly with those of the A.B.H. Consols Lode which appears to have emanated from the north end of the Broken Hill Main Lode Horizon during high grade regional metamorphism. The Consols Lode has been regarded as of Thackaringa type, and both are regarded as possibly arising from the remobilization of Main Lode Horizon ore. Whilst this may yet prove to be so it appears that the marked differences in mineral composition between the Consols and the Thackaringa types, would require somewhat different modes of regeneration.Thackaringa ore, as well as A.B.H. Consols ore, on this basis, would necessitate the development of a metahydrothermal ore fluid to account for their present apparently hydrothermal (or pseudo-hydrothermal) constitution...

Jan 1, 1967

By Perring CS, Vearncombe J. R, Ho SE, Groves DI

Large Late Archaean greenstone belts in Western Australia, Canada and Zimbabwe, contain abundant mesothermal gold, volcanogenic massive base-metal sulphide, and komatiite-associated Ni-Cu mineralization. These greenstone belts are similar in many respects to convergent and accretionary plate margins found in the Pacific rim; modem environments which are cor-respondingly rich in gold and base-metal mineralization. The giant gold placer deposits of the Late Archaean Witwatersrand Basin (the world's largest gold producer) formed in a foreland or retro-arc basin; in a similar tectonic setting to much modem placer mineralization around the Pacific. Gold and volcanogenic base-metal sulphide mineralization are abundant in Late Archaean terranes and the Pacific rim because1. gold mineralization is a product of convergent margin tectonics, and 2. accretion in convergent margin orogens provides the best chance of preserving base-metal mineralization related to submarine volcanism.It is therefore likely that the abundance of gold and base-metal sulphide mineralization in the Late Archaean reflects the widespread growth and sta-bilization of continental crust via tectonic processes broadly similar to those operating in the present Pacific basin.

Jan 1, 1990

Some important mineral fields are referred to in discussing the formation of placer deposits in Australia. Testing methods include boring hand, with percussion rigs; with auger and pit digging drills; and l by vibro drilling. Sampling errors are minimized by the use of correct techniques and equipment for boring, sampling, and sample dressing, A hypothetical set of data is used to demonstrate the final process of evaluation, and some relevant taxation provisions are discussed.

Jan 1, 1964

By Klenowski

Rational design of layouts for longwall operations is greatly facilitated by use of an accurate and economical method for predicting stresses and displacements. The displacement discontinuity method (a form of boundary element method) is based on replacing actual excavation geometries by thin slits of the same plan area. This approach allows three-dimensional stress- analysis at a fraction of the cost of alternative methods. The analyses can be readily performed on economical microcomputers, putting the analysis capability within the reach of mine-site personnel. This paper describes investigations associated with the German Creek Central Colliery, the first longwall operation in Queensland's Bowen Basin. The material properties used in the model, in particular the rock mass and goaf properties, have been 'tuned' to fit stress measurements obtained during extraction of the first and second longwall panels at the mine. The study shows that model predictions based on suitably scaled anisotropic rock strata properties are in good agreement with the stress measurements made to date. This model predicts average chain pillar loads significantly higher than predicted by models based on United Kingdom conditions. A working chain pillar design method is proposed using average pillar loads predicted by the numerical model and ultimate strength characteristics given by Bieniawski's formula.

Jan 1, 1988

By Till M, McGee WA

The Hermit Islands are situated at 145¦ E 1 30'S in the Bismarck Sea approximately 200km WNW of Manus Island. They are dominated by basalt flows, one of which yielded a K/Ar isotopic date of 3.4 + 0.05Ma. All basalts examined were olivine-bearing, but one sample also contained hornblende. Although many outcrops were weathered, no evidence of pervasive hydrothermal alteration was observed on any islands and non-weathered rocks are petrographically fresh and many retain glass.

Jan 1, 1990

Process variables in flotation circuits are outlined with a view to producing mathematical models of circuits. The nature of the kinetics of flotation are discussed and the effect of process variables on the kinetics considered. An approach for a possible model is briefly outlined.

Jan 1, 1971

By Ulvelin K, Antila K

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

By Bennet A. G

As part of the construction of the Melbourne Underground Rail Loop it was necessary to construct two 7 metre diameter tunnels, each 100 metres in length, by shield driven excavation through an alluvial valley at Elizabeth Street. The tunnels had a primary support of bolted precast reinforced concrete liner blocks and were excavated with the aid of compressed air. The work was undertaken by the Tunnelling Group of the Melbourne and Metropolitan Board of Works as nominated sub-contractor to John Holland (Constructions) Pty. Ltd. The paper describes some of the problems associated with the construction of the above tunnels and the methods used to overcome them. In particular

Jan 1, 1981

By Bhattacharyya A. K

In this paper, the current methods for predicting surface subsidence due to underground coal mining are evaluated first. A single index, called a strata parameter (P), is then proposed to describe the overall character of the undermined strata in the context of surface subsidence. Based on the strata parameter, a method for predicting the maximum surface subsidence for various panel width (w)/depth (h) ratios is presented, which has been tested against specific empirical curves or data from several coalfields in different countries. From the data relating to several coalfields, a linear relationship between the reported average angle of draw and the strata parameter has been established. It has also been found that the strata parameter can be used for studying the locations of the inflection points and the shapes of transverse subsidence profiles.

Jan 1, 1995

By A J. Tucker, L Bottomley

The principle objective of development mining is to create thoroughfares that can be accessed by personnel and machinery for the entire life of an underground mine. The drill and blast process, being the primary method used when creating these thoroughfares, needs to be able to adequately fracture the rock to be removed whilst at the same time minimising any damage that may be sustained to the rock surface that remains. This process of damage prevention is known by a variety of different names including smooth blasting, sculpture blasting, contour blasting and controlled blasting. Whilst the terms are different, the objective is the same and that is to reduce and better distribute the explosive charges to minimise stressing and fracturing of the rock beyond the neat excavation line. The process in this report will be referred to as perimeter control blasting. This paper will discuss the benefits of using perimeter control blasting in a development mining operation and the theories that govern how these blasting techniques work. The methods that are used to implement perimeter control blasting will also be addressed, paying particular attention to how these blasting techniques have evolved, spawning new and improved perimeter control products. Finally some attention will be given to the process of optimising perimeter control blasting in any underground mining operation.

Jan 1, 2005

By Hayes P. C, Matthew S. P

The product morphologies formed on the reduction of dense wustite crystals are classified into three types, A) porous iron, B) porous wustite covered with dense iron, and C) dense wustite covered with dense iron. The mechanisms of formation of these structures and the effects of impurity elements on the product morphologies are discussed.

Jan 1, 1985

By Longworth C. R

Competing requirements for land usage sometimes make the correct all- ocation difficult. The decision can be complicated by many factors such as local resident pressure, previous government decisions, economic pres- sures and the duration or permanency of the competing land usages. This problem often confronts the extractive industries with consequent delays in granting leases and some- times considerable local dissension. A proposal to extend the high grade silica sand quarry of the Wamberal Sand Company Pty. Limited is a microcosm of these competing requirements. The sand quarry is located on the New South Wales central coast. It is an open pit operation on a near beach deposit of silica sand suitable for flint glass manufacture.

Jan 1, 1976

By Stokes WPC

The capital requirements to develop a new mining venture are becoming very large; amounts of the order of US$1,000 million are not now unusual among estimates to bring new mining complexes into production. At the same time prevailing political and economic conditions are making it increasingly difficult to determine whether or not a project is likely to be viable. These factors emphasise the need to carry out thorough evaluation studies of all mineral prospects before making major investment. Additionally with the rapidly changing economic climate existing at the present time, it is becoming more and more necessary to carry out reappraisals of existing mines. An important function of both initial evaluations and reappraisals is to provide the operators of the mine with effective mining plans to ensure that the operation will meet its required economic targets. P, p M. tl p b, c v, s c 1 n 1 f r d c e c e u w Modern computers are well equipped to store and manipulate large amounts of data with speed and reliability. Their use in the mining field r is increasing and this trend serves to free f technical staff from much of the time consuming m and error prone hand calculations which were o formerly required in determining reserves and w carrying out all forms of mine planning. r Nevertheless, computers are not a universal

Jan 1, 1980

By Hengst B

The first production stage in any mining operation is the breaking of whole rock into fragments small enough for loading and subseq- uent handling. This primary fragmentation is most frequently accomplished with blasting. The maximum fragment size and the fragment size distribution have an influence on the subsequent loading, handling and crushing costs. It is assumed that total rock fragmen- tation in practice is a result of an interact- ing array of radial cracks from various blastholes. The representation for the basic pattern of radial cracks emitted from a particular blasthole is first described. A model is then developed simulating the interaction between blastholes at various burdens and spacings, and in simultaneous and delayed modes. The resultant picture is analysed and a fragment size distribution calculated. Methods of incorporating the existing faults in the rock are also discussed. Finally application of this model to various facets of mining are considered.

Jan 1, 1977