Search Documents

By L. S. Castleman, R. K. Hotzler

We are currently studying the effects on recrys-tallization of impurities diffused into dispersion-hardened alloys. Our interest in this phenomenon was originally aroused by the observation that the recrystallization temperature range of tungsten "doped" with alumina and silica, or with thoria, is lowered drastically if nickel is plated onto the tungsten prior to heat treatment.' In this note, we report a similar effect that sulfur has on the recrystallization behavior of thoriated nickel. The experimental procedure for this exploratory phase of the investigation has consisted simply in heating commercially obtained stress-relieved samples of thoriated nickel for varying temperatures and times in sealed capsules containing air and small quantities of sulfur. The samples contain 2.4 vol pct thoria and initially less than 18 ppm S by weight; they are prepared either from 0.5-in.-ciiam rod stock or from 0.092-in. sheet and are in the "as-received" (stress-relieved) condition prior to exposure. In an atmosphere free of sulfur, such samples do not show evidence of recrystallization after being annealed for 1 hr at a temperature of 2500°F (1372C).2 The photomicrograph in Fig. 1 shows the microstructure of one of our samples annealed for 75 hr at 1000° C (1832°F) in a sulfur-free capsule. The grain structure is hardly evident (if at all) at 465 times magnification. In contrast, the photomicrograph of Fig. 2 shows the recrystallization that has taken place in a sample exposed to sulfur for 5 hr at 1000°C (1832°F). A nickel sulfide phase is visible at the grain boundaries of the light-appearing grains. We have also observed recrystallization to occur in a sample annealed at 600°C (1112°F) for 25 hr. This temperature is below the 637°C (1178°F) eutectic in the Ni-S system. In the latter case, no nickel sulfide phase is evident in the microstructure. Moreover, we have noticed the occur-

Jan 1, 1969

By W. L. Fink, H. C. Stumpf, L. A. Willey

VERY few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.l0 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. MATERIALS The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society.4 Chemical analysis of the aluminum showed the following impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectrographic standard procedures5 No. IIA and No. SII respectively. DETERMINATION OF LIQUIDUS The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano.6 As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 ½ -in. iron pipe and pipe caps. The space around the sides of the crucible was filled with 40 mesh crystalline alundum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1948

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylam-monium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x105 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values.2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x105 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle

Jan 1, 1958

A development drilling and bulk sampling program should furnish the following information: (1) geology of the mineralized zone, (2) quantitative data on grade and tons of material within pertinent cutoff limits, (3) physical size and shape of the deposit and areas underlain by waste as well as ore, (4) mineralogical and metallurgical characteristics of the ore, (5) physical characteristics of the ore, (6) bulk samples for metallurgical testing and grade, (7) data on factors that affect mining operations, such as ground water and ground conditions. The method and equipment best suited for a particular drilling job depend upon the geologic features of the mineral deposit to be tested.

Jan 10, 1967

By Thiann R. Yu, William J. Quesnel

At Kidd Creek, the annual production of 4.5 million tonnes of ore has been achieved primarily with sublevel blasthole stoping. This mining method has allowed underground operations to meet the designed production capacity while maintaining an outstanding safety record. To achieve this goal, rock mechanics principles have been integrated into each facet of mining in the planning stage, in the production stage, and in various stages of ground support. This paper evaluates the two adopted mining sequences based on ground stress patterns, blasting control, ground reinforcement, backfill support, and numerical modelling for stope stability at the mines.

Jan 1, 1984

By Albert Sauveur

The following propositions and corollaries are intended to present, as concisely as possible, some of the evidences gathered while studying the microstructure of steel. Each proposition is accompanied by photo-micrographs showing the structure of illustrative samples. But it must be understood that the special instances thus chosen for illustration are by no means the only ones on the examination of which the propositions are based. On the contrary, they have been taken almost at random among a great many, in some instances more than a hundred, similar cases. Proposition I. A slow and undisturbed cooling from a temperature x or higher produces crystallization. Plate L, Plate II., Fig. 1, and Plate V., Figs. 1, 2, 3 and 4 show the crystalline structure of several pieces of steel. Plate I. reveals this structure in the center of a slowly-cooled Bessemer ingot, 1.5 feet from the top. Plate II., Pig. 1, is from a small 2-in, square testingot of the same heat, slowly cooled. Plate V., Figs. 1, 2, 3 and 4 show the structure of different parts of steel rails. The original photographs were all magnified 70 diameters, and have been reduced in engraving to 63, or to 55 diameters, as shown in the plates. Proposition 11. Undisturbed cooling from an initial temperature lower than x is not accompanied by crystallization. Plate III., Fig. 5, shows the structure of a piece of rail-steel forged from a white heat until it had fallen to dull-red. The structure is almost amorphous. Practically no crystallization has taken place during the subsequent cooling. Corollary.—Pieces of steel finished at a temperature lower than x do not take a crystalline structure.

Jan 1, 1894

By C. Hays, R. E. Swift, E. G. Kendall

Investigations of the Zr-Pt system, by metallography, incipient melting, and X-ray diffraction, determined the phase relationshifis from 0 to 50 at. pct Pt. Phase fields in the Pt-~ich region were outlined, and three intermetallics (ZrPt, Zr2Pt, and ZrPtd were located. A eutectic between Zr and Zr2Pt, and a eutectoid veaction between Zr and a Zr + Zr2Pt, were established. The maximum solubility of Pt in P Zr was approximately 13.5 wt pct, as opposed to less than 1 wt pct solubility in a Zr. EARLIER work on the Zr-Pt system was limited to an X-ray study on the intermetallic compound, ZrPt3, by H. J. Wallbaum,1 It was reported that ZrPt3 existed at 86.52 wt pct Pt, and had a hexagonal structure, isomorphous with TiNi3. Wallbaum&apos;s data revealed the following structural particulars: a = 5.633A, c = 9.21A, and c/a = 1.635A. Other studies allied to Zr-Pt alloys concerned only 1) Pt-rich alloys (0.05 to 5.0 pct Zr) for corrosion resistance,2 2) a Zr-base alloy with 5 pct Pt and 0.124 pct C for oxidation resistance,3 and 3) electroclad-ding of Zr with Pt for in-pile corrosion resistance of Zr to uranyl sulphate. 4 Metallographic, incipient melting, and X-ray diffraction techniques were applied to accurately resolve the phase relationships in the 0 to 50 at. pct (68.2 wt pct) Pt region, and to outline the phase fields in the Pt-rich area. Three intermediate phases: Zr2Pt, ZrPt, and ZrPt3, were also established by the same methods. PROCEDURE Melting stock for this program was of the highest purity obtainable. The Zr was iodide crystal bar with a low hafnium content of about 0.05 wt pct (Westinghouse "Grade 3"). The as-received Zr was treated to remove the surface film of corrosion product that resulted from a standard autoclave grade designation test. Next, the bars were processed to yield material suitable for arc melting and free of contaminants. Sheet platinum metal (Baker and Co. "Grade 2") was used for alloying additions. This material con-

Jan 1, 1962

By E. H. Jr. Dix

OF all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations had been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 5.25° C. to about 1 per cent. at 300° C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540° C., and that this amount decreases to about 3 per cent. at 20° C.

Jan 2, 1926

By D. W. G. White

The surface tension of zinc has been determined by the sessile-drop method in a progvam emphaszzing detailed experimental care. The surface tension oj. the pure metal was measured over a range of ternperature from the melting point (419.6"C) to 540°C. At the melting point, the suvface tension of zinc was found to be: 1) 99.99+ pct Zn - 757.0 5 dynes per cm 2) 99.999+ pct Zn - 761.0 5 dynes per CI 3) 99.9999 pct Zn - 76&apos;7.5 5 dynes pev cna From experiments carried out in a closed, isothermal cell, the temperatuve coejyicient of the surface tension (6y/6T)p, , of zinc xas found not to be negative but to be postiue. A positive tenzperatre coefficient indicates a greater depee of order in the surface than in the body of the lquid. Houlezer, by delibevately inducing continuous zaporization, a temperature coefficient of su)face tension with a negative slope can be produced. The work reported herein was undertaken as part of a larger program of fundamental research on the properties of molten zinc and zinc alloys. This program grew out of a continuing interest at the Mines Branch in the behavior of liquid metals in the foundry and of a desire on the part of the zinc industry for reliable basic data. The work was originally begun in cooperation with the Consolidated Mining and Smelting Co. Ltd., Trail, B.C., and was subsequently continued from 1960 to date in association with the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Although the surface tension of liquid zinc has of course, been measured before, as Table I and Fig. 1 demonstrate, there is not good agreement among the existing values. Such disparities arise because sources of experimental error are insufficiently controlled. This situation places the reader in doubt. One result may be correct within narrow limits—even fortuitously—yet, because there is not agreement between several values, none can be accepted with conviction and all become suspect. It seemed, therefore, in the circumstances, that there was room for further work embodying considerable emphasis on experimental care in order that, within a small margin of error, an accurate value might be obtained. It was in this spirit that the work was undertaken. METHOD The sessile-drop method -as adopted for this work. In this method, when applied to liquid metals at elevated temperatures, the outline of the meridional section through a drop resting freely on a horizontal surface is recorded photographically. Certain parameters

Jan 1, 1967

By Frederick Laist, H. J. Maguire

The ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaccs, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper; this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it mas found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first- and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator produces a product that is self-fluxing; in fact, it is possible to produce a concentrate containing more iron than is necessary to flux the silica. Under these conditions, the amount of basic fluxing materials required for the smelting operations became very srnall and the converter slag lost its former value as a blast-furnace flux. For this reason, a less expensive method of recovering the copper, silver, and gold contained in it than smelting in blast furnaces had to be found. It was not feasible

Jan 1, 1921

By J. B. Newsom

IN the September 1936 issue of MINING AND METALLURGY the pioneer work of boring a 5-ft. shaft to a depth of 1125 ft. at the Idaho Maryland mine in California was described. Later, a Bureau of Mines Information Circular (No. 6923) gave additional data. In re¬cent months still further progress has been made in this technique through the sinking of a 5 1/2-ft. shaft for Pickands, Mather & Co. at their Zenith mine, Ely, Minn. The present work was done with new carefully designed equipment and several experienced men so that progress, as shown below has been much better:

Jan 1, 1938

By H. O. Hofman

PAGE Part I. Decomposition OF Zinc Sulphate by Heating in Air, . 811 I. Introduction............ 811 II. Zinc Sulphate Used,..814 III. Fumes and Pyrometers,........ 816 IV. Heating Zinc Sulphate—Dehydration,...... 817 V. Heating Zine Sulphate—Decomposition...818 (a.) Beginning of Decomposition..818 (b.) Rapidity of Decomposition,..819 (c.) End of Decomposition..823 (d.) Retardations in Heating.-Curve,..825 (e.) Formation of Basic Salts,..826 Part II. Decomposition OF Zinc Sulphate by Heating with Carbon (Reducing Roast), .830 I. Introduction,........... 830 II. Experiments and Results ,.........832 III. Summay,........... 834 Part 111. Formation of Zinc Sulphate by Roasting,... 834 I. Introduction,........... 834 IT. Description of Blende,......... 836 III. Outline of Operations,.........838 IV. Details of Experiments.......... 839 1. Decrepitation,.......... 839 2. IgnitionPoint,....839 3. Sulphatizing-Roast of Joplin Blende..840 4. Sdphatizing-Roast of Warren Blemde ,..843 5. Sulphatizing-Roast with Addition of Pyrite...848 6. Summary of Sulphutizng-Roasts,....... 854 Part IV. Appendix : Formation of Zinc Ferrate...856 Part I. Decomposition of Zinc Sulphate by Heating in Air. I. Introduction. With the exception of lead sulphate. all common metallic

Jan 1, 1905

By Charles Bohdanowicz

The accompanying tables&apos; show that in 1936 production of crude oil in Poland decreased very slightly (Tables 1 and 5), by about 1 per cent, and that gas production increased by about 11 per cent. As in preceding years, drilling (Tables 1, 2 and 3) was devoted principally to extension of oil fields in the Jaslo district (fields 1, 5 and 7) and, in a lesser degree, of those in the Stanislaw6w district (field 27). Production of crude oil is being sustained in a large measure by the deepening of old wells; besides a total number of 183 new wells completed (Table 3) about 152 wells were deepened, and in a general way the results of deepening were better than those of new wells drilled. Reserves of "proved land" have not increased as far as crude oil is concerned, but a notable extension of gas fieldsZ was attained in Daszawa (field 25) and in the Roztoki area (field 5). In the sub-carpathian zone gas fields have been proved in the vicinity of Kalusz, Kos6wJ and in the northwestern sector of that zone, between Tarnow and Lezajsk. The gas horizons of Daszawa occur in the Upper Tortonian, those of Kos6w in the Lower Tortonian (Middle Miocene). Exploratory drilling has been performed near Kalusz, and has been commenced near Kos6w and in the Tarn6w area. The Kos6w gas approaches the "wet" type. A possible gas reserve with a volume of 4,000,000,000 cu. m. (141,000,-000,000 cu. ft.) has been calculated, for an area of about 5 sq. km. of the Daszawa field, on the basis of production obtained and of decreases in pressure and their distribution. The fields of Roztoki and Strachocina (No. 12) have not yet supplied sufficient data for a calculation of reserves, which might possibly be estimated at 2,000,000,000 cu, m. (70,000,-000,000 cu. ft.).

Jan 1, 1937

Strain-Hardening Exponent of Cross-Rolled Beryllium Sheet by S. R. Maloff, Vol. 215, No. 5, page 872, was omitted from Table of Contents for the October issue. Stabilization Phenomena in Beta Phase Au-Cd Alloys by Howard Birnbaum, Vol. 215, No. 5, page 786. The figure denoted Fig. 1 should be Fig. 3, Fig. 3 should be Fig. 4 and Fig. 4 should be Fig. 1. The captions are in the proper sequence. Activity of Carbon in Liquid Iron Alloys by Tasuku Fuwa and John Chipman, Vol. 215, No. 4, page 708. First equation, right hand column, page 710 should read

Jan 1, 1960

J. E. Stead, Middlesborough, England (communication to the author): Prof. Howe&apos;s valuable paper on cast-iron brings forward most prominently the correct explanation of the part played by combined carbon in pearlite and cementite, in determining the strength and hardness of cast-iron. On a previous occasioil I have shown that castings made by melting a white Cleveland iron and glazed iron, one containing 1.5 and the other from 4 to 5 per cent. of silicon, and each about 3 per cent. of carbon, were stronger than those made of ordinary foundry-iron; the difference in the final castings being a differ-

Jan 1, 1902

By M. Hall, Y. P. Chugh, A. Okunola

Effects of moisture absorption on the behavior of the Dykersburg shale overlying Harrisburg coal seam in Southern Illinois are presented in this paper. Cylindrical samples of the shale 2.5 cm in diameter and 5.0 cm long were studied for weight gain and swelling strains at 90, 95, and 100 percent relative humidity and under immersed water conditions. After attaining equilibrium conditions, the samples were studied for changes in the strength and deformation behavior. The depth of moisture penetration was measured using the Vickers microhardness measurements. Using the basic mass transfer concepts, effective diffusion coefficients were computed for the shale.

Jan 1, 1981

J. E. Stead, Middlesborough, England (communication to the author): Prof. Howe&apos;s valuable paper on cast-iron brings forward most prominently the correct explanation of the part played by combined carbon in pearlite and cementite, in determining the strength and hardness of cast-iron. On a previous occasion I haveoshown that castings made by melting a white Cleveland iron and glazed iron, one containing 1.5 and the other from 4 to 5 per cent. of silicon, and each about 3 per cent. of carbon, were stronger than those made of ordinary foundry-iron; the difference in the final castings being a differ-

Jan 1, 1902

By S. J. Matas, R. F. Hehemann, R. H. Goodenow

The hot-stage metallographic method has been employed to determine radial growth rates of upper and lower bainite. Lower bainite appears to grow as individual plates that increase in both length and thickness while upper bainite grows as sheaves of closely spaced plates or needles. A discontinuity in the temperature dependence of the growth rate appears to be associated with the transition from upper to lower bainite and stepped quenching experiments suggest that lower bainite will not continue to grow when the temperature is raised to the upper range. Thus, a single process does not appear to control the growth of both upper and lower bainite. A tentative model based on the forces acting on a dislocation interface is proposed to account for the slow growth of bainite. It has been recognized since the early studies of Davenport and Bain that a close relationship exists between the martensite and bainite transformations in steels. However, diffusion of carbon during the transformation has lead to considerable controversy concerning the reaction mechanism.1-7 Many studies4,5,7-9 have emphasized the structura and kinetic aspects of the bainite reaction and, in particular, the difference observed between the two forms of bainite—frequently termed upper and lower bainite. A kinetic difference between the two types of bainite has been revealed in the activation energy determined from the overall reaction;4,5 however, many difficulties arise in an interpretation of these activation energies since a number of temperature dependent factors contribute to the kinetics of the overall reaction. The displacive surface relief10 accompanying the bainite reaction permits a separation of the nuclea-tion and growth contributions to the reaction and allows the kinetics of the growth process to be examined. Several investigations of this type have been conducted; however, they have been restricted to the low temperature range.3&apos;6&apos;11 Here, bainite plates are observed to grow slowly in both length and width. The present investigation extends such studies to include the upper bainite range. MATERIALS AND PROCEDURE Materials. The composition of the steels studied in this investigation are presented in Table I. The range of composition permitted a study of the effect of carbon content on the growth rate of upper bainite in the 9 pct Ni steels and consideration of both upper and lower bainite in the higher carbon steels. These steels were received as hot-rolled rounds and were forged to approximately 1/2 in. thick plates for preparation of metallographic specimens. In order to produce an essentially zero carbon steel, Steel A was decarburized in wet hydrogen at 1550°F for 15 days with the result tabulated as Steel AD. Experimental Procedure. In order to study the slow growth of the displacive transformation product, a commercially available Leitz hot stage was modified to permit heating of the specimen by its own resistance in a manner similar to that employed by other investigators.6 The furnace chamber was maintained at a pressure of 2 to 3 X 10-5 mm Hg prior to austenitizing at 2000° ± 12° F for 5 min. Samples could be cooled from the austenitizing to the transformation temperature in approximately 15 sec and the progress of transformation was recorded with a 9 cm by 12 cm single frame camera or a 16 mm movie camera. RESULTS AND DISCUSSION Growth Characteristics. The general growth characteristics observed in this investigation were analogous to those reported previously.3,6,11 Typical growth sequences for the high temperature and low temperature forms are illustrated in Figs. 1 to 5. In both temperature ranges, bainite plates increase in length at slow, temperature dependent rates until interrupted by a grain boundary, another plate, or

Jan 1, 1963

By H. W. McCue, Henry Rogatz

Oil.—During the year 1939, there were 365 oil wells drilled in the Texas Panhandle, with a total daily initial production of 130,968 bb1.— that is, 69 fewer oil wells drilled than in the previous year, with a decrease. in total daily initial production of 61,738 bbl. The total daily potential of the field on Dec. 5, 1939, as determined by the Texas Railroad Commission, was 1,344,677 bbl., an increase of 94,032 bbl. over the previous year. On Dee. 5, 1939, a daily allowable of 130,527 bbl., which was an

Jan 1, 1940

By Henry Rogatz, H. W. McCue

Oil.—During the year 1939, there were 365 oil wells drilled in the Texas Panhandle, with a total daily initial production of 130,968 bb1.— that is, 69 fewer oil wells drilled than in the previous year, with a decrease. in total daily initial production of 61,738 bbl. The total daily potential of the field on Dec. 5, 1939, as determined by the Texas Railroad Commission, was 1,344,677 bbl., an increase of 94,032 bbl. over the previous year. On Dee. 5, 1939, a daily allowable of 130,527 bbl., which was an

Jan 1, 1940