Search Documents

By G. P. Walters, W. C. Fuller

THE production of thin films of beryllium became essential early in the irradiation program at Harwell in order to study the fundamentals of irradiation damage in this metal. In common with other metals, electron-microacope specimens of beryllium can be produced by different techniques. The techniques used to produce thin-film specimens varied according to the starting material. Most of the starting material was -0.060 in. thick. Large-area specimens (1 in. long by 0.5 in. wide) were chemically thinned to -0.005 in. thick in a solution containing 85 pct orthophosphoric acid, 10 pct chromium trioxide, and 5 pct sulfuric acid at 70°C prior to electropolishing. Small-area specimens, Fig. 1, had to be mechanically thinned prior to electropolishing because chemical thinning considerably reduces the area as well as the thickness. Mechanical thinning tends to produce a worked layer about 0.002 in. deep and hence this method cannot be used to thin bulk specimens below about 0.005 in. thick. Mechanical thinning is carried out by mounting the specimen on perspex then carefully polishing on wet grinding papers. Polishing is continued until about half the initial thickness is removed; the reverse side is then polished in a similar manner. After the bulk specimens have been mechanically or chemically thinned to -0.005 in. they are elec-tropolished in the solution shown in able I at 50" to 80°C. This solution should be prepared by adding the chromium trioxide to the orthophosphoric acid and then the glycerol last. The glycerol should be added slowly because a vigorous effervescence can occur. Electropolishing is carried out by holding the specimen in stainless-steel tweezers and gently agitating in the solution. Masking or "window" techniques are not required for beryllium, good microscope specimens being obtained from the edges of elec-tropolished foils. A stainless-steel beaker should be used, acting as the cathode and solution container. A closed circuit voltage of 30 v is used for polishing. Too low a voltage produces a matt surface and pitting occurs when it is too high. The solution temperature is important. If it is too low, the solution is viscous and bad polishing results and, if too high, etching of the specimen occurs. After electropolishing, the foils are thoroughly

Jan 1, 1963

By B. E. Lindsly

The withdrawal of gas and/or oil in appreciable quantity from a natural oil reservoir causes the pressure within the reservoir to diminish, and if the oil is completely saturated with gas, this dissolved gas begins to evolve from solution. The liberation of gas from solution in oil causes the oil to change in several ways, the principal changes being: (1) reduction in volume or "shrinkage"; (2) increase in specific gravity (decrease in degrees A.P.I.); (3) decrease of energy in the oil; (4) increased viscosity; (5) increased surface tension. As the writer's investigations have been concerned more with the first three items than with changes in viscosity and surface tension the following discussion relates particularly to the volumetric shrinkage of the oil, to the increased specific gravity, and to the decreased energy in the oil, each caused by the liberalion of dissolved gas. One of the most surprising facts that have developed in the study of high-pressure well-head and "bottom-hole" samples is the great reduction in volume that occurs in some oils when the naturally dissolved gas is liberated. High-pressure samples taken from well heads in the Oklahoma City, Kettleman Hills and Ventura, Calif., fields decreased in volume from 11.2 to 40.5 per cent when the dissolved gas was liberated in reducing the pressure on the sample to atmospheric. The amount of shrinkage an oil undergoes when gas is liberated depends upon the quantity of gas liberated and also upon its composition. A given volume of the heavier gases, propane and butane for example, will occupy more space in the oil than an equal volume of methane. The reason for this probably is that the molecules of the heavier gases are larger than those of the lighter gases. When gases are not in solution, and particularly when they are at low pressures, the distance between the gas molecules is so much greater than the dimensions of the molecules themselves that the mere size of the molecules has little effect upon the space occupied by the gas, Avogadro's hypothesis, which in effect states that all gases under the same conditions have the same number of molecules per unit volume, relates to this phenomenon. The fact that the heavier gases occupy more space than the lighter gases in the oil, and

Jan 1, 1934

By F. E. Bash

PREVIOUS to the war, this country depended on Europe for its supply of a number of alloys of great importance in the manufacture of electrical apparatus and equipment. When this source was cut off shortly after the beginning of hostilities and the small stocks in the United States were exhausted, either inferior substitutes had to be used or the manufacture of the apparatus suspended. Since electrical equipment was of primary importance in the prosecution of the war, the substitutes had to be used until the composition and processes of manufacture of the alloys could be determined. Included among these alloys was one generally known as manganin, which is composed chiefly of copper and manganese and which, beside having a low-temperature coefficient of resistance, has a low thermal electromotive force against copper. These qualities make it valuable for the manufacture of electrical instruments and machines in which it is used in the shape of wire, rod, and strip. As a result of these circumstances, an investigation was started to deter mine how manganin could be made on a commercial basis so that a product of uniform quality and the necessary electrical characteristics could be produced. The object was to procure an alloy with temperature coefficient of resistance not greater than T 1 X 10-5 per ° C. and a thermal e.m.f. against copper no greater than that of the imported material. It is characteristic of manganin that the temperature-resistance curve is not a straight line but has a peak, which varies in position with different samples; it is most desirable, however, to have it at a temperature of 25° C. if possible. The coefficients of manganin from all records available ranged from a large negative to a large positive value. The composition as reported by different authorities is given in Table 1. Prof. Matthew A. Hunter, of Rensselaer Polytechnic Institute, made up a number of small melts of manganin in a graphite crucible and the one that he reported as having the best coefficient gave the following analysis: Copper, 83.6 per cent.; nickel 2.5 per cent.; manganese,-13.6 per cent.; iron, 0.3 per cent. An analysis of a sample of German manganin gave the following: Copper, 82.6 per cent.; nickel, 3.8 per cent.; manganese, 12.8 per cent.; iron 0.7 per cent.

Jan 9, 1919

By Terje Preber

Undisturbed sampling of shale has always been difficult. As pert of a comprehensive subsurface investigation for a nuclear power plant in northwestern Illinois, the Maquoketa shale, which contains seams of argillaceous dolomite, was sampled using different coring techniques. Since the Maquoketa shale is extremely fissile, careful sampling preservation by both lateral and vertical confining was utilized. The samples were tested to determine both static and dynamic properties. A relationship between void ratio and compression index, swell index, and swell pressure ratio was established. Correlation was found between the dynamic properties and both undrained shear strength and confining stress. Based on the results of the sampling and testing programs, recommendations for sampling and sample preservation techniques are given. INTRODUCTION Undisturbed sampling and preservation of samples of weathered, fiasile shale is often a very difficult task. The often erratically varying degree of weathering with depth complicates sampling and makes reproducibility of testing results difficult. Therefore, the testing of weak, weathered rock very often yields a wide variety of test results with large data scatter. The reproducibility of teat results usually associated with water-deposited soils is seldom, if ever, obtained. The testing and sampling program described in this paper was part of a comprehensive subsurface investigation for a nuclear power plant in northwestern Illinois. The sampling, preservation and testing program of shale samples taken from the Maquoketa shale are described, and, in particular, the different sampling techniques and sample preservation procedures are evaluated with respect to their effectiveness. The samples obtained by these procedures were subjected to a comprehensive testing program, including both static and dynamic testing in order to provide input for soil-structure interaction analysis. GEOLOGY The Maquoketa Shale Group is of Ordovician age and is part of the Cincinnatian Series. The area where the shale samples were taken was in a broad sea far from sources of clastic sediments during most of Ordovician time. However, during Cincinnatian time when large deltas in the Appalachian region were being formed, clastic sediments from the east dominated the sedimentation ii. Illinois, resulting in formation of the shale and dolomite shales of the Maquoketa Shale Group (Willman et al., 1975). The geologic unit sampled consists of a greenish gray to gray silty shale containing numerous 1- to 12-inch (2.5- to 30.5-cm) thick interbeds of argillaceous dolomite. The dolomite comprises up to 40 percent of the profile studied. The shale

Jan 1, 1984

By Harold R. Bradford

EXPANSION initiated during and after the war has placed industrial plants in new areas and increased reduction and manufacturing facilities in communities already established. With added expansion interest has grown in possible area contamination from waste products. Evolved flue waste contains many chemical contaminants that may or may not cause concern; however, atmospheric pollution has always been a problem to industrial communities. For some time effects attributed to small quantities of compounds of fluorine in various waste gases have been studied by industrial, medical, agricultural, and associated interests.1'2 Aside from an article by Churchill, Rowley, and Martin in 1948," little has been published on the subject of fluorine in coal except by foreign investigators. The first indication of fluorine compounds in coal was noted in England in 1934 by R. Lessing,4,5 who found that the presence of fluorine in Midland and West County coals was definitely established by etching of glass and by severe corrosion of porcelain fillings in a gas works scrubber. Etching of glass in a direct contact annealing kiln initiated research, and in 1944 four papers were published by H. E. Crossley,6-9 giving results of investigations of fluorine in coal of England by the Fuel Research Board, Department of Scientific and Industrial Research. These investigations studied methods of determining fluorine, the quantities present in various coal deposits, the geographical distribution of fluorine in British coals, occurrence of fluorine in minerals associated with coal, amounts of fluorine compared to other constituents of coal, the nature of fluorine compounds, and industrial significance of fluorine in coal. It was shown that British coals contain from 5 to 200 ppm of fluorine, which is probably present as fluorapatite [Ca10F2(PO4)6], often written as [3Ca3P2O8.CaF2]. The fluorapatite is intimately associated with shale in some coals and can often be separated from these coals along with the shales. H. E. Crossley8 also reported no correlation between the amounts of chlorine, sulfur, or ash and the amount of fluorine in different coals. He found, however, a relationship between the content of fluorine and phosporus in many British coals. Thus it should be possible to anticipate likely fluorine-rich coals from existing data giving phosphorus content. Behavior of the fluorine compounds of coal was compared with that of 12 fluoride-phosphate minerals in sink-float separations and solvent ex-

Jan 1, 1958

By Goro Shimaoka, Kichizo Niwa

IN the past, the crystalline states of graphite in cast iron have been studied by many investigators. Recently several authors 1-4 have published interesting information on the crystal texture of the individual graphite grain, especially spherulites in nodular cast iron. In regard to the crystal structure of graphite, Lipson and Stokes0 howed by powder X-ray analysis that most of the crystals contain about 14 pct rhombohedra1 structure (ß-form) which differs from the hexagonal structure (a-form) in the sequence of layer stacking. Hoerni6 onfirmed the existence of the ß-form in a single crystal with electron diffraction by Kossel-Moellenstedt's method. Furthermore, Hoerni and Weigle7 found extra reflections in electron diffraction patterns, which are given by a unit cell twice as large as the usual one in the basal plane. Recently, Lukeshs observed graphite twinning and satellite reflections in his X-ray work and considered them as evidence for the existence of an orthorhombic superstructure. Owen and Street" and Matuyama" studied the structures of graphite crystals in several types of cast iron, using the X-ray powder method, and they showed that the graphite crystal contains a certain amount of the ß-form, an amount which varies with the sources of the cast iron used. The present study was made in order to secure structural information on graphitization in cast iron. Electron diffraction studies on the structure of single graphite flakes segregated from molten carbon or silicon-rich iron at 1200" to 1500°C are reported. Experimental Honkeiko pig iron (4.05 pct C, 1.59 pct Si, and 0.65 pct Mn) was used as the solvent of carbon or silicon. The pig iron was melted in an open furnace and a small quantity of metallic silicon was added to the melt at 1300°C. The melt was heated to 150O°C, and then retort black carbon or metallic silicon was added little by little. The components added to the bath contained approximately 5.0 pct C and 2.0 pct Si in the carbon-rich material, and 3.8 pct C and 5.4 pct Si in the silicon-rich iron. These two types were held at 1500°C and then cooled without graphitizing by cutting the heat sup-

Jan 1, 1958

By T. S. Lovering

The Moffat tunnel passes through the continental divide about 50 miles west of Denver, Colo., on the Denver & Salt Lake R. R.: It is 16 ft. wide, 24 ft. high, and 32,383 ft. long, a distance of a little more than 6 miles. The advantages accruing from its construction may be briefly summarized as follows: The tunnel eliminates 27 miles of grade averaging more than 3.5 per cent. and actually running well over 4 per cent. in many places, and changes the steepest grade from 4.5 to 2 per cent. It reduced the peak of the railroad from 11,660 to 9249 ft. which enables one engine to pull four times as much freight as it could before the tunnel was built. If the Denver & Salt Lake R. R. completes its line, this road will shorten the distance between Denver and Salt Lake City by 200 miles and will have no steeper grades than the lines now connecting the two cities. The proposal to drive the tunnel through the divide dates back about 25 years and D. H. Moffat, who was the leading spirit in the organization of the Denver & Salt Lake R. R. spent much of his time and energy in efforts to raise money for the tunnel that bears his name. He was unsuccessful and died before the work was started. In 1920 an effort was made to obtain state legislation favoring a bond issue to finance three important railroad tunnels in Colorado but the measure was defeated, largely through the efforts of the citizens of the region near Pueblo. A few years later devastating floods caused the Pueblo voters to seek relief from the state and at this time they withdrew their objection to the tunnel bond issue. As a result, a $6,720,000 bond was issued to finance the Moffat tunnel. Construction bids were so high that the work was finally allotted on a scheme analogous to a cost-plus basis. The contract was awarded to Hitchcock and Tinckler, who are paid a fee of $140,000 for driving the tunnel. All bills are paid by the Moffat Tunnel Commission. The contract was let Sept. 19, 1923, and Hitchcock and Tinckler agreed to complete the work by July 19, 1927. In the event of finishing before this date they were to be given a bonus of $1000 a day and

Jan 1, 1928

By Enid C. Plante

To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), rnarcasite (FeS2), orpiment (As&.), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also exarnined to determine if its behavior could be correlated with that of pyrite or rnarcasite (FeS2. Experimental Method Mineral for Flolation and Contact Tests Mineral was prepared in the manner a1ready described1 and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and CO2-free air bubbled through each suspension at a constant rate (about I bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation , oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the 'supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.l No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 Flotation of "Unoxidized" Minerals with Ethyl Xanthate as Collector Fig I to 3, 4. 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox8 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1949

By C. A. Stickels

In a recent paper, Held1 showed that rolling conditions can have a marked effect on the volume fraction of surface texture produced in low-carbon steel. This variation in rolling texture is reflected in the recrys-tallization texture and affects the plastic properties of the annealed sheet. The fact that roll friction can influence the surface deformation texture in iron and steel has been known for some time;'= but the magnitude of the effect has never been shown quite so clearly before. The analogous effect during wire drawing has been recognized for many year.4 Dillamore and Roberts5 examined surface textures in warm- and cold-rolled aluminum and copper. They found that when a surface texture was present it could be described as the interior texture rotated about the transverse sheet direction. The angle of rotation was a function of the type of lubrication, the amount of reduction per pass, and the temperature of rolling. The purpose of the present note is to show that surface textures in cold-rolled iron can also be described as interior textures rotated about the transverse sheet direction. Vacuum-melted electrolytic iron* was straight- rolled 90 pct at room temperature in a two-high rolling mill with 5-in.-diam rolls. Two rolling procedures were used: a) no lubrication with reductions of about 0.035 in. per pass, and b) heavy lubrication with lano-line and reductions of about 0.002 in. per pass. The final sheet thickness was 0.030 in. (110) pole figures were determined by transmission through specimens taken from the sheet surface and sheet midplane. The surface texture of the sheet cold-rolled according to procedure a is shown in Fig. l.* The shapes of the low-intensity contour lines indicate that the texture can be described as a partial fiber texture with a (110) fiber axis normal to the sheet. The approximate range of orientstions present is (011)[211] — (0ll)[100] — (011)[211]. This range of orientations is what one would obtain by rotating the interior texture 90 deg about the transverse sheet direction. The intensity of (110) and (222) reflections from planes parallel to the surface was measured after removing metal from the surface by chemical polishing. The surface texture here was confined to the outer

Jan 1, 1968

By Robert F. Mehl

THE solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstätten figures profusely nor with great ease. A study of the Widmanstätten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstätten figures.1 ALLOYS OF ALUMINUM WITH COPPER The most accurate determination f the solid solubility, of copper in aluminum seems to be that by Dix and Richardson,2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548°, and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solution on cooling tends to precipitate the compound CuAl2, and this conclusion has been confirmed experimentally by Schmid and Wassermann .3

Jan 1, 1932

By W. Joseph Schlitt, William D. Southard, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott's Bingham Canyon copper precipitation plant, one of the world's largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12 - 15% moisture could be consistently delivered for smelting.

Jan 6, 1979

By William D. Southard, Joseph W. Schlitt, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott 's Bingham Canyon copper precipitation plant, one of the world's largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12-15% moisture could be consistently delivered for smelting.

Jan 1, 1980

By C. A. Stewart

PAGE. I. Introduction............ 241 II. Location. TopoGRaphy. and History....... 243 III. DescRiption of the Rocks......... 245 1. Altered Sediments.......... 245 2. Alaskite........... 246 3. Alaskite.Porphyry.....255 4. Quartz Dikes........... 257 5. Biotite.Granite.......... 256 6. Quartz.Porphyryl......... 260 7. Andesite........... 262 8. Miscellaneous Dikes......... 263 IV. Age oF the Rocks and Comparison with other Localities.. 263 V. AlteRation............ 265 1. Sericitization........... 265 2. Silicification........... 266 VI. StRuctuRes........267 1. Dip of the Limestone......... 267 2. Faulting........... 267 VII. Contact - metamorhism,.......... 269 1. Endomorphism.......... 269 2. Exomorphism......... 271 Recrystallization and Loss of Color...... 271 New ,Minerals.......... 272 Addition of Material........ 274 Volume.Changes.... 276 Locus of Metamorhism........ 277 Method of Precipitation.........278 VIII. ORe-Deposits............ 278 1. Contact-Metamorphic Copper.Ores,..... 279 General..........279 Shape and Distribution........ 279 Minerals........... 281 Secondary Enrichment........ 282 2. Disseminated Copper.Ores........ 283 3. Origin of the Copper.Orcs........ 284 4. Lead-Silver Ores.......... 287 IX. Bibliography............ 288

Jan 1, 1913

By Charles S. Barrett, Frederick N. Rhines, Robert F. Mehl

The solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstatten figures profusely nor with great ease. A study of the Widmanstatten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstatten figures.' Alloys of Aluminum with Copper The most accurate determination of the solid solubi1it.y of copper in aluminum seems to be that by Dix and Richardsoq2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548", and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solu-lion on cooling tends to precipitate the compound CuA12, and this conclusion has been confirmed experimentally by Schmid and Wassermann.

Jan 1, 1932

By William B. Plank

FOR the third consecutive year, I have collected the data on enrolment and employment of graduates from the schools in. the United States and Canada that grant degrees in mineral technology. The data were collected in the same way as formerly; namely, by questionnaire, dated Jan. 5, 1935, and are therefore comparable with the figures reported for former years. This year, along with the names of the 48 schools in the United States and the six in Canada, are listed the courses offered and the degrees granted by each, school, together with the names of the professors in charge. The names and addresses of the four schools in Mexico are also given. The list is on pages 450-1, which should he valued as a directory by those interested in mineral technology education. So far as is known, this is the most complete and up-to-date list that has ever been published.

Jan 1, 1935

By J. F. KENP

THE White Knob copper-deposits are situated about three miles south of Mackay, on the Salmon River .branch of the Oregon Short Line Railroad, in Custer county, Idaho. An outline-map of this district is given in Fig. 1. The deposits have been known and spasmodically worked for many years, and a total of over 3.5 miles of tunnels, shafts and other workings has been driven with a view to their development. These extensive excavations have exposed the deposits sufficiently to permit a careful geological examination. The peculiar features which give special interest to this paper are the branching, free-like form of the ore-bodies; the absence of zones of secondary enrichment in the partly oxidized pyritic deposits, and the fact that while the deposits are associated in a general way with the contact of an eruptive rock with limestone, which it penetrates, the garnetization has taken place not in the limestone, as is the usual case, but in the igneous

Mar 1, 1907

Total U.S. mineral production reached an estimated $17.8 billion for 1960, 4 pct above 1959 and second only to the record high of $18.1 billion established in 1957. As a group, metals achieved a rise from $1.6 billion in 1959 to $2.0 billion this year, an increase of 28 pct. Similarly the value of nonmetallic production including fuels (i.e., natural gas, petroleum, natural-gas liquids, asphalt and related bitumens, carbon dioxide. anthracite. bituminous and lignite coal, peat, and helium) rose from $15.5 billion in 1959 to approximately $15.8 billion in 1960. However, this 2 pct increase in the total value of non-metallic production was due to an increase in the value of the fuels ($11.8 billion in 1959 to $12.2 billion in 1960) which offset a drop in value of the other nonmetallic minerals ($3.7 billion in 1959 to $3.6 billion in 1960).

Jan 2, 1961

By L. S. Austin

I. Introduction............ 431 II. Organization............ 432 III. Production............ 434 IV. Transportation............ 435 V. Sampling..........436 VI. Concentration............ 440 VII. Blast-Furnace Plant........... 442 1. Construction........... 442 2. Operation............ 450 VIII. Advantages of Large Furnaces........ 455 1. Saving in Fuel........... 455 2. Saving in Jacket.Water..... 455 3. Quick and Large Discharge of Matte and Slag... 455 4. Decrease of Incrustation... 456 5. Elasticity of Operation..457 6. Large Flow Through Fore.Hearths...4. 57 7. Alterations Without Interruption..458 8. Variations in the Composition of Slag....458 9. Less Labor-Cost.......... 458 10. Less Initial Cost.......... 460 IX. Briquetting.Plant........... 460 X. Roasting-Plant............ 462 1. Kilns............ 462 2. Reverberatory Furnaces...468 XI. Converter-Plant........... 474 1. Construction ..........474 2. Operation.......... 476 XII. Flues and Stacks........... 478 XIII. Arsenic-Plant............ 480 XIV. Coke-Washing Plant.... 452 XV. Slime.Ponds ........... 483 XVI. Brick-Plant............ 484 I. Introduction. The Washoe plant; in Anaconda. Mont., together with the local street-railroad, ranches. a foundry and machine-shop. A

Jan 1, 1907

By E. L. Jr. Spain

THE deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of. Mississippi and Alabama respec-tively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewell1 and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance.

Jan 1, 1936

By Per Kofstad, Hallstein Kjöllesdal

The oxidation behavior of niobium (columbium) has been studied in the temperature range 500° to 1200°C and at oxygen pressures of 760,100, 10, 1, and 0.1 mm of Hg. The work comprises kinetic studies of the oxidation as well as structural investigations of the oxidized specimens by means of X-ray diffraction, electron diffraclion, electron microscopy, and metal1ographic techniques. The oxidation reaction has a highly irregular temperature dependence and is unusually sensitive to changes in the oxygen pressure. The complex oxidation behavior is suggested to be due to formation of different Nb2O5 modifications in different temperature regions. During oxidation oxygen is also dissolved in the metal. Formation of oxide whiskers take place on the oxide surface at temperatures above approximately 800°C. VARIOUS aspects of the oxidation of niobium have been studied.l-12 The investigations show that niobium has a complex oxidation behavior, and the oxidation

Jan 1, 1962