Search Documents

By D. C. Jillson

BRIDGMAN1,2 melted metals in a graphite or hard glass tube and lowered the tube through a furnace to make it cool from one end only. Because of the difficulty of eliminating all vibration of the mold, others have raised the furnace instead. Neither way seems as desirable as a setup with no motion of either the mold or the furnace. A furnace in which both the shape and the slope of the temperature gradient could be controlled and varied over a wide range and in which such a gradient could be moved from one end of the furnace to the other, freezing the specimen from one end to the other, at any desired rate, all by means of isolated external control, seemed to offer definite advantages. In addition to eliminating the possibility of vibration due to moving parts, it might also give better control over the direction and rate of heat flow. Such an apparatus was assembled and is shown schematically in fig. 1. Equipment Furnace: A clay-carborundum tube of 3 1/2 in. ID with a % in. wall thickness was used as the core. This had a main winding of No. 12 B.&S. gauge Nichrome V with some compensation for heat loss at the ends. Taps to this winding were made at points 12 in. from each end. Fig. 2 shows details of this winding and of the two end windings. Each end winding was wound over Micanite over the main winding. No. 15 B.&S. gauge Nichrome V was used for these, and again taps were supplied at two inter-mediat,e points on each. The tube was supported in an 18 in. OD black iron shell with brick insulation. The input to each of the windings was regulated by means of a variable transformer. Temperature Regulation: A chromel-alumel thermocouple located near the furnace wall in the center of the furnace was connected with a Celec-tray controller, type PIC, 300" to 900°C range, which opened and closed a shunt across an external variable resistance in the main winding circuit. An "anticipatory response" device also was incorporated to minimize the cyclic effect of the control mechanism. Eleven survey couples in a common pyrex glass protection tube were located near the furnace wall and spaced 2 in. apart. The couple leads went to a common reference junction box where they were connected to copper leads from a selector switch which, in turn, was connected to a type K potentio-meter. This arrangement permitted rapid temperature surveys. The knob on the controller dial was replaced with a threaded brass spool turned at a controlled rate by a thin iron wire one end of which was attached to a gear train and the other to a small weight heavy enough to prevent slipping of the wire on the spool. The gear train, driven by a 1-rpm Telechron motor, contained a series of different sized interchangeable gears and threaded drums permitting a range of travel speeds from 0.10 in. per hr up to a hypo-

Jan 1, 1951

By W. L. Freyberger, R. B. Booth

Froth flotation is a chemically induced method for beneficiating or up- grading an ore, which utilizes a layer or column of froth as a separating medium to segregate and remove the valuable minerals from the worthless gangue components of a finely ground ore suspended in water. The object of this chapter is to discuss the theoretical aspects of froth formation, the various frothing agents employed in flotation, and the effect of chemical structure on froth formation, and to correlate these factors with flotation technology. The flotation method of separation is conducted in three main steps: 1) selective chemical modification of the surface of specific mineral particles to effect floatability or nonfloatability; 2) contact between air bubbles and mineral particles, the selective adherence of floatable minerals to these bubbles, and the rejection of nonfloatable minerals; and 3) separation of the floatable minerals from the nonfloatable minerals. As indicated above, these three operations are achieved by the use of chemicals. Frothers play their most important role in the second and third steps by influencing particle- bubble contact and by affecting the degree of separation obtained in the froth column. Frothers, as defined by flotation operators, are compounds that are used specifically for the purpose of creating a froth in a flotation separation. How- ever, some collectors produce froths that are adequate for some flotation operations. Although this chapter is chiefly concerned with the specific frothers used in flotation, some discussion of frothing collectors is included. Otherwise, collectors (or promoters) and modifiersare not discussed at length; for information on these types of flotation chemicals, the reader is referred to other sections of this book or to other sources.l HISTORICAL DEVELOPMENT OF FROTHING AGENTS Historically, there are two distinct phases in the development of frothing agents and other flotation chemicals: 1) 1860 to 1920-oil flotation, and 1921 to date-chemical flotati0n.2~3 Early in the first period, large quantities of fatty and oily materials, up to 10 to 20% of the weight of the ore, were used as a means of separating the sulfide and oxide components from the gangue minerals in ore pulps. Later, various gases replaced these large quantities of oil as a buoyant and separating medium, decreasing oil requirements to less than 1% of the weight of the ore. With this reduction in oil

Jan 1, 1962

By D. K. Crampton, H. l. Burghoff, J. T. Stacy

THE effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions The large number of alloys investigated made it impossible to study every one in the detail it may have merited Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold-working tends to disorder the structure, resulting in very marked lowering of conductivity The random state of atomic arrangement produces lower conductivity than the ordered state for the same composition 1 PREVIOUS WORK previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys The increase of resistivity due to severe working was less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21 7 per cent increase of resistance for an alloy containing 67 9 per cent Cu as severely worked Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens The resistance decreased again when the cold-worked crystals were subsequently annealed Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working The conductivity of 72-28

Jan 1, 1941

Gentlemen.-It is pleasant to be able to report that the year just closed has been a prosperous and successful one for the Institute. As is shown by the reports of the Treasurer and the Finance Committee, the business affairs of this organization are in excellent condition. With property valued at more than three-quarters of a million dollars, and with considerable sums in various funds and endowments, it is possible to spend on each member of whatever class $22.65 each year, more than the maxi- mum amount of dues received from any one, and substantially twice the average amount, $10.94, received from all. To do this has required close management and a strict regard for our limitations. In 1926, when the Budget was made up, the estimated expenditures for the work which it was felt the Institute must do exceeded the estimated receipts by some $14,000. At the close of the year, despite a number of unexpected decreases in receipts, it had proved possible to accomplish substantially all the work laid out and close the books with the usual transfer of initiation fees to the General Reserve, and still only reduce the cash balance $2,074.54. This was made possible by the hearty and loyal cooperation of the whole staff of employees and the extremely large amount of gratuitous service rendered by the officers, the members of the Divisions and technical Committees, and the membership generally. Even so it was impossible, because of limitations of funds, to undertake many things it is highly desirable for the Institute to do, and it was necessary to refuse the publication of important papers and committee studies, because of the lack of funds. PUBLICATIONS In an analysis of the income and expenses of the Institute published in the February issue of our Journal, MINING AND METALLURGY, it was pointed out that the largest item of expenditure is, as it should -be, for publications. Printing, binding, and distributing the various technical papers sent to the members cost in 1926 more than all the money received from dues, including the portion allocated as subscription to the magazine. Within the. year, the following volumes were printed and, with the exception of the second volume of TRANSACTIONS, which was mailed in January, were distributed : TRANSACTIONS, Volume 73, 1241 pages, covering papers on non-ferrous metallurgy, milling and concentration, non-metallic minerals, iron and steel, and the Institute of Metals Division papers read at the

Jan 1, 1928

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. We are referring here, of course, to properties inherent in the just solidified ingot and are not considering variations in properties caused by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. In plain carbon steels these elements are ordinarily not more than five: carbon, manganese, silicon, phosphorus, and sulphur. In alloy steels the special alloying elements also are specified and. determined. It might be thought that variations in properties due to such variations in ordinary chemical composition are to be expected, well understood, and hence not in need of discussion in this chapter. It will be considered here, however, that this phase of the subject is not always wholly clear. Furthermore, it certainly seems profitable to seek the explanation of anomalous properties in the ordinary chemical composition of the steel before looking into less well understood variables of open-hearth practice. It is sometimes surprising to learn that some puzzling variation in properties is caused merely by a variation in the ordinary analysis of the steel. This surprise is apt to be due not to general lack of knowledge of the effects of the composition of steel upon its properties but rather to the fact that we do not happen to have been previously much concerned with the particular property under consideration. For example, if we are accustomed to using S.A.E. 1035 bars for applications which depend chiefly on the stiffness, strength, and toughness of the steel in the as-rolled condition, we might quite logically develop the conclusion that variations in carbon content from 0.30 to 0.40 per cent are not significant. Then if we later have occasion to make heat-treated bolts of the same grade of steel, we may be surprised to

Jan 1, 1944

By M. B. Willey

The Louisiana Continental Shelf is a submarine area extending offshore as much as one hundred miles. The Gulf bottom in this region varies considerably in extent, profile and composition and consists largely of sedimentary deposits, predominantly those of the Mississippi River. It is very young in a geological sense. Up to the present time few major structures have been erected offshore in the Gulf and no comprehensive preliminary tests have been carried out. Results of pile driving tests are of little value as actual bearing capacities far exceed the dynamic resistance to driving as measured by conventional formulas. Soils encountered are, with few exceptions, cohesive and piling consequently develop their supporting power through surface friction. Because of the time required and relatively high costs, no complete load tests have been made. The results of those tests which have been made, and information obtained from pulling piling in one structure, indicate that design loadings could be considerably increased, and it is contended that comprehensive preliminary investigations including an actual load test, combined with borings and examination of materials encountered by competent soil experts, would effect economies in design far in excess of their cost. The Louisiana Continental Shelf—General The Louisiana . . . continental shelf is a submarine area which extends seaward for as great a distance as one hundred miles off the present shoreline. The Gulf bottom in this region is characterized by low slopes and its outer margin is outlined by the fifty fathom (300 ft.) contour. South of the margin of the shelf the slopes steepen abruptly in the continental slope zone and plunge into the deeps of the Gulf of Mexico.l The engineer who is called upon to design a structure on this shelf is concerned only with the uppermost portion to a depth generally not to exceed Ioo to 150 ft. This layer is very young in a geological sense, and it has the characteristics usually associated with infancy. A few of these are lack of strength, lack of uniformity, and high water content. It consists of the sedimentary deposits of the various rivers and streams entering the Gulf. These streams are all heavily burdened in quantities sufficient to fill the areas at their mouths, were it not for the fact that continual subsidence, equal or greater in amount and acting directly opposite, prevail over the sedimentary workings of the streams. This subsidence has been estimated by geologists to be at the rate of at least one foot per century. Influence of Mississippi River The Mississippi River, which has been the predominant factor in the formation of practically all the Louisiana continental shelf, is one of two rivers flowing into the Gulf that have been able to build protruding deltas. The Mississippi has done so because of its enormous size and load. It deposits sediments in amounts sufficient to replace and actually gain on the amount of subsidence.

Jan 1, 1949

By J. Gardner Brooks, Sidney Sigel, Irvin R. Kramer

In 1942 Grossmannl proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigaton2-6 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent Lipon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a finite quench than predicted by Grossmann's factors for an infinite quench (Table I). Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most Of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Gross-mann's grain-size correction curves, determined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1947

By C. O. Swanson

In the iron ranges of northern Michigan, magnetic data have been used as an aid in geologic field work since the time of the earliest surveys. The presence of complex structures containing magnetic formations, and the general scarcity of exposures, guided the early work into this line of attack, and later field studies tended to place more and more emphasis upon this geophysical relationship, until, at present, the collection of magnetic data is a matter of routine in any areal survey. At first, horizontal deflections of the compass needle were the only data collected. In subsequent surveys, greater dependence was placed on dip-needle readings, which record variations in the intensity and inclination of the earth's magnetic field. Recently the trend has been toward adjusting the instrument so as to reduce the influence of changes in inclination, and using a more sensitive modification, called the Superdip,' in weakly magnetic areas. To a minor extent, the magnetometer has also been employed. The object of this paper is to present the writer's experience with magnetic data in this region. The conclusions are based on work covering a period of 10 years, and spread over nearly all of the iron ranges and a large part of the intervening areas. The viewpoints expressed are purely geological ones. In other words, any opinion as to the usefulness of a certain relationship is based upon the writer's experience with it as a guide in interpreting the structures of this region, and not upon its soundness theoretically, nor its usefulness under other conditions. A very brief summary of the conclusions is as follows. The most important step is that of collecting the magnetic data. This requires a suitable adjustment of the dip needle, and sufficient readings to accurately portray the variations in the magnetic field, which are apt to be irregular. Once the readings are taken and plotted in some clear fashion, the interpretation of them is usually merely a matter of observing their relation-

Jan 1, 1934

By Robert H. Richards

The adaptation of European methods of concentrating ores to suit the conditions of this country has followed the lines that simplify machinery, diminish labor and increase capacity. Noteworthy instances are the substitution of hydraulic classifiers for the last one or two trommels in the series, and the substitution of a distributing-tank for the slimes in the place of the Spitzkasten. The question may be fairly asked, At what point do losses become serious in consequence of these changes? It is to study this question that the investigation herein described has been undertaken. After the losses are located and the methods of stopping them are pointed out, it will then lie with the individual mill to decide whether or not the plans proposed will save suficient value to warrant their adoption. In the discussion of sorting followed by sizing, as the terms are used in this paper, me have to deal with the preparation of slimes by the Spitzkasten for subsequent washing upon the slime-table. The Spitzkasten, or pointed box, is an inverted hollow pyramid, generally of wood, usually with four faces or sides coming together in a point below. The sides can have, according to Rittinger, a minimum angle of slope of 50" with the horizontal. The feed-water carrying fine slimes (less than 0.01 inch, or 0.25 mm. in diameter) for treatment is fed at one end and carefully distributed over the whole width. The outlet is over the opposite end. The water-current passes direct from inlet to outlet, and has usually been regarded as a surface-layer pass-

Jan 1, 1898

By C. C. Wright, T. S. Spicer

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By T. S. Spicer, C. C. Wright

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By R. J. Schaefer, M. E. Glicksman

Direct, in situ observation of metallic alloys during solidification reveals that in some systems crystal multiplication occurs by means of a dendrite remelt-ing process, without the necessity of independent nu-cleation events. The solidification is observed on optically clean surfaces of supercooled molten alloys. In one system (Sn-3 wt pct Bi) , a fine-grained equi-axed structure is produced by the complete disintegration, via remelting, of transient initial dendrites. In contrast, several other metallic systems show little or no evidence of remelting activity. The behavior of these metallic systems is consistent with that expected on the basis of published observations of dendrite remelting in transparent organic alloy systems. It is concluded that dendrite remelting is an important crystal multiplication process in some metallic alloys, but is velatively unimportant in some other alloys. The detachment of dendrite branches from the primary stem by a remelting process has been observed by Jackson, Hunt, Uhlmann, and seward1 during the solidification of some transparent organic alloy systems. The branches released by this remelting process can drift free of the primary stem and serve as seeds for the formation of numerous independent crystals. This proliferation of new crystals does not require repeated independent nucleation events, but only modification of the initial solidification structure. The mechanism of dendrite remelting, as described by Jackson et a1.1 and by Tiller and O''Hara,2 is dependent on the transport of both heat and solute and is, therefore, expected to operate only in alloys, and not in pure substances. It was found in the transparent organic alloy systems that remelting occurred primarily in the constricted regions near the base of dendrite branches, where the branches had grown through the solute-rich liquid layer surrounding the primary dendrite stem. It was suggested that impure solid had formed in these constricted regions at a relatively low temperature and had later become unstable as further solidification of purer material raised the temperature. Jackson et al. proposed that the equiaxed zone of metal alloy castings originates from a similar remelting process, and they demonstrated the operation of this mechanism in "ingots" poured from saturated salt solutions. Although these substances were especially selected to show solidification behavior similar to that of metals,3 the remelting mechanism has, until now, been subject to the objection that its operation has not been directly observed in a metallic system. Considering the fact that thermal properties such as diffusivity may differ by as much as two or three orders of magnitude between metals and organic compounds, this objection was considered to be possibly serious. A method has now been developed by which it is possible to make direct optical observations of metals during solidification. This method has revealed transient solidification processes which would not be detected by metallographic examination of totally solidified specimens. In particular, a grain-refinement process in a metallic alloy has been observed to be a direct consequence of the total disintegration of an initial dendritic structure. The influence of an initial, transient solidification structure on the final solidification structure is demonstrated here for the first time in a metallic system. I) EXPERIMENTAL The technique of using a transparent flux to maintain an optically clean metal surface during solidification has been described by us elsewhere.* The

Jan 1, 1968

By C. G. Dunn, J. L. Walter

Secondary recrystallization to the (110) [001] texture in high-purity silicon iron occurs if low-oxygen material is annealed in a nonoxidizing atmosphere. Any departure from these conditions results in a growth of (100) oriented grains. The nature of the matrix and secondary recrystallization structures and textures and the nature of grain boundary interactions during growth show that the low gas-metal interfacial energy of the (110) surfaces provides the driving force for growth of these grains. A type of grain growth, characterized by a driving force which derives from energy differences of {hkl} surfaces at the gas-metal interface, has been treated in recent papers.&apos;-7 Secondary recrystallization to the cube text!:: in high-purity silicon iron provides one example. The present paper also deals with a surface energy driving force but the texture that results by secondary recrystallization is not the cube texture; it is a texture in which the (110) plane is in the plane of rolling and the [001] direction is in the direction of rolling. The phenomenon described in this paper is different from the impurity (dispersed phase)-controlled secondary recrystallization process in which the (110) [001] oriented grains grow under the action of grain boundary driving forces.8-12 It is also different from tertiary recrystallization,2 which also produces the (110) [001] texture in high-purity silicon iron, since the matrix textures and grain sizes are different. Finally, it is unlike any other form of secondary recrystallization reported in the literature. The possibility of obtaining the (110) [001] texture in high-purity silicon iron became clear in a study of the effect of impurity atoms on the energy relationships of (100) and (110) surfaces. In this study Walter and Dunn6 observed the migration of (100)/(110) boundaries, i.e., boundaries between two grains, one of which has a (100) plane and the other a (110) plane, respectively, parallel to the plane of the sheet specimen. At 1200°C the (100)/(110) boundaries advanced into (100) grains in a vacuum anneal, then reversed their direction and migrated into (110) grains in a subsequent anneal in impure argon. Finally, the direction of migration reversed once again with (110) grains growing into (100) grains in a second vacuum anneal. These results were explained in terms of a change in concentration of oxygen atoms at the gas-metal interface during the anneals. Thus, oxygen atoms were added to the surface during the anneals in impure argon to the point where ?100, the specific surface energy of the (100) oriented grains, was lower than ?110, the surface energy of (110) oriented grains. In vacuum, however, the oxygen concentration at the surface was lowered to the point where ?110 < ?100. Concerning the possibility of secondary recrystallization in high-purity silicon iron with a low initial oxygen concentration, the observed effect of adsorbed oxygen atoms has indicated6 that a good vacuum anneal would favor the rapid growth of matrix grains with the (110) plane in the plane of the sheet much more than grains in the (100) orientation. The growth of only (110) oriented grains of course would depend upon y110 being less than ?hkl, where hkl refers to any plane different from (110). The present paper is concerned with the application of the above ideas to secondary recrystallization to the (110) [001] texture in high-purity silicon iron. The matrix and secondary recrystallization textures and structures are defined and discussed. Observations of growth of nuclei for secondary recrystallization and of boundary interactions are included to provide direct information on the surface energy relationships between (110) and other (hkl) surfaces. EXPERIMENTAL PROCEDURE As before, 2,4-6 high-purity iron and silicon were melted and cast in vacuum to provide an alloy containing 3 pct Si with less than 0.005 wt pct impurities. The oxygen content of the ingot was lower than in previous ingots, being approximately 3 ppm (by weight). The carbon content of this ingot may have been slightly higher than was found for previous ingots. The same rolling and annealing schedule used previously2 was followed in this study to obtain samples 0.012 in. (0.3 mm) thick. These samples were electropolished prior to annealing. After rolling and polishing, the oxygen content of the material was approximately 6 ppm; material used in the previous studies contained about twice this amount of oxygen.

Jan 1, 1961

By Carl J. McHargue

Rods of 99.99 + pct Al which had initial orientatzons of <001>, <118>, <115>, <111>, and random were swaged at room temperature. Changes in orientation as a function of deformation were studied on axis distribution charts. The <001> orientation appeared to be relatively stable due to the inhomogeneity of the deformation process. near the <100> zone were quickly reoriented towards <001>. Orientations on the <110> zone between <118> and <115> appeared to be stable to reductions of about 50 pct, then were reoriented toward <001>. At very high reductzotzs. movement away from the <111> orientation was observed. the requirement that a circular cross section be maintained. In addition to these mechanical factors, there are grain-boundary effects in poly crystalline materials which are not yet understood. Hartmann and Macherauch conclude, for example, that multiple slip occurs for all orientations in fine-grained aluminum and copper and that the choice of operative slip systems has no simple relationship to orientation.? Many investigators have attempted to avoid problems of interpretation caused by an initial texture by treating the starting material to obtain as ran- IT has been generally accepted that the deformation texture obtained at high reductions, e.g. 90 pct, will not be noticeably affected by a prior texture; whereas, that obtained at reductions of 40 to 50 pct may be significantly influenced by the specimen history.&apos; Some recent studies, however, have been interpreted as showing that an initial texture strongly influenced the deformation textures in rods at reductions greater than 90 pct. Freda and Cullity suggested that the <001> texture in a heavily cold-worked copper rod was due to a <001> texture in the original casting. McHargue, Jetter? and Ogle concluded that the <001> component in an aluminum rod extruded at liquid nitrogen temperature was remanent from a <001> texture in the cast extrusion billet.3 Most of the published work on the effect of initial orientation on deformation textures has been for cold-rolled or compressed single crystals,4-6 The primary interest in these studies was to examine various orientations with regard to their stability under flow? thus determining the possibility of such orientations being stable end orientations. There appears to be no published studies on the effect of initial orientation on fiber textures in polycrystalline specimens. A recent study, however, is concerned with the reorientation of individual grains in polycrystalline specimens pulled in tension.? Although the reorientation of single crystals loaded in simple tension is well known, the movements in the forming of wires and rods would be expected to be different due to the circular array of radial-compressive stresses exerted by the die walls or the rolls, and to

Jan 1, 1962

By R. T. Hukki

IT is no great exaggeration to say that present grinding practice and economics are largely determined by lining design. A record of outstanding liner wear can be achieved with any liner surface pattern that will positively lock the outer layer or layers of grinding media. With no slippage, lining wear is bound to be slight. At the same time, popular practice calls for tumbling loads of about 50 pct of mill volume to obtain maximum grinding capacity. Innumerable parallel grinding investigations have verified that optimum speed for such a mill lies within 70 to 85 pct of theoretical critical speed. If the mill is speeded up to 100 pct of critical, little or no grinding can be accomplished. Earlier Work on Supercritical Grinding: First investigations concerning grinding at supercritical speeds seem to be very old. Remarkable work on the subject has been performed by White,&apos; and his experiments have been described and summarized by Richards.&apos; White&apos;s contributions seem to have passed unnoticed by Fahrenwald,2,3 whose extensive experiments have been well presented, yet apparently very little appreciated. Additional work on grinding at supercritical speed has been reported, e.g., by Lewenson and Tscherny,&apos; USSR; Anselm and Grunder,&apos;, Germany: and Rose and Evans." Great Britain. Subcritical and Supercritical Speeds: In the formula of the critical speed given in the textbooks of mineral dressing, no factor indicating the coefficient of friction is generally included. If this factor = 1.0, which is equivalent to grinding conditions in a mill provided with heavily ribbed lining, the formula of the critical speed holds as such and grinding is possible at subcritical speeds only. In a mill equipped with a smooth or relatively smooth lining, the numerical value of the friction factor in the denominator of the formula becomes <1.0, indicating that grinding at supercritical speeds should be possible in such mills. It has been recently shown by the author&apos; that a wide supercritical speed range will become available for grinding—and especially for fine grinding—if the basic conditions within the mill have been selected properly. Mathematical analysis of mill dynamics at supercritical speeds&apos; has indicated that the mill speed may be increased if: 1) total mass of grinding medium decreases, 2) mass of the individual grinding piece increases, and 3) the coefficient of friction between the outer layer of medium and the mill lining decreases. It is obvious that the mass of the individual grinding piece will be affected by its shape and by its specific gravity. The coefficient of friction decreases with: 1) increasing smoothness of liner surface, 2) increasing roundness of the grinding piece, 3) increasing fineness of material to be ground, 4) decreasing pulp density, and 5) decreasing hardness (abrasiveness) of the mineral to be ground. In a mill equipped with heavily ribbed lining, practically no size reduction will take place between the lining and the outer layer of tumbling medium, because slippage is prevented. In the overwhelming majority of today&apos;s mills the grinding accomplished is by virtue of cataracting and/or cascading media with some action within the tumbling charge. Sub-critical speeds only can be applied. In grate-type or peripheral discharge mills equipped with a smooth lining a tumbling load of any kind of common medium occupying about 50 pct of mill volume will behave in such a way that practically no slippage will take place. This has been verified in experiments run by the author in the laboratory and in pilot plant mills&apos; equipped with smooth lining. Again, the operation is limited to the subcritical range. In a mill with a smooth lining, grinding will be possible either at subcritical speeds or within a wide supercritical speed range as soon as the basic requirements for a desired speed are fulfilled. In a mill operated at supercritical speed, any point on the liner surface proceeds at a speed greater than that indicated by the formula of the critical speed, while any grinding piece situated in the outer layer of the medium against the lining proceeds in the same direction at a speed less than that indicated by the critical speed. This speed difference produces a very effective attrition grinding zone between the liner surface and the outer layer of the medium. The share of attrition grinding of the total grinding accomplished increases rapidly with increasing speed in the supercritical speed range. The smooth surface of the mill lining may be well illustrated by the surface of a bucking board. The outer ball layer may be similarly represented by the lower surface of a muller. If the bucking board, the material to be ground, and the muller all proceed in the same direction at the same speed, no grinding will result. This is the general situation in the mills of today. If, however, the muller is pulled with respect to the board, moving or stationary, grinding will be accomplished effectively. Although grinding in today&apos;s mills is primarily the result of cataracting and/or cascading media, the principal place of grinding at high supercritical speeds will be the attrition zone.&apos; In the mineral dressing laboratory of the State Institute for Technical Research. Helsinki, Finland, large quantities of different ores have been ground in a pilot plant ball mill (3x3 ft) at a top speed about 230 pct of the critical. With the same mill, theoretical investigations concerning the grinding characteristics of ball mills equipped with a smooth lining have been carried out up to the speed of 313 pct&apos; of the critical. With a smaller mill, the grinding characteristics with a variety of grinding media have been investigated at speeds up to 2000 pct of the

Jan 1, 1959

By R. W. Raymond

Through the courtesy of Mr. James H. Mayo, a member of the Institute, who is in charge of the operations of the Mindrinetti Company in the Saramacca district of Dutch Guiana, I have received specimeris of certain peculiar pseudomorphs of limonite after pyrite, which occur abundantly in the auriferous deposits of that. region.* I am indebted to Mr. H. Tweddle, a geiltleman- connected with the same company, for some particulars of interest con-

Jan 1, 1899

C. A. HANSEN (communicated appendix*).-Since the above paper was written, tests have been conducted with a view to securing a sounder basis for discussing the effects of temperature on the behavior of the zinc cell. The following data, while making no pretense to great accuracy, are still reasonably close. Cells were operated with the same feed solutions, but at varying temperatures, the latter being controlled by means of immersed steam coils. Current efficiencies obtained indicate that the corrosion rate

Jan 11, 1918

By H. H. Rachford, J. Douglas, D. W. Peaceman

A numerical solution of equations describing two-phase flow in porous media shows promise in providing a technique for predicting the displacermet from satlds of oil by water or gas. The description includes the influence of relative permeability, fluid viscosities and densities, graviry, and capillary pressure, and, tholrgh tested ortly for two-dimensional cases, should be eqlmlly applicable in three-dimensional geometry. Two memorical methods ore presented: the first method is quite general in its applicability; the second method can be used only with certain types of boundary conditions but requires less computing. Comparisons of computed results with data from Inhoratory models are presented. These data were taken on a water flood of a strarified model and on water floods of a five-spot model for favorable and unfavorable mobility ratios. On the stratified model, excellent agreement with recovery at breakthrough was obtained; agreement with recovery after breakthrough was poor. In the five-spot model, good agreement was obtainecl with recovery at and after breakthrough. The purpose of this paper is twofold: first, to present a reservoir engineering method requiring knowledge only of rock geometry and the normally measured rock and fluid properties for calculating the multi-dimensional flow of water displacing oil from porous, water-wet rock containing connate water; and, second, to investigate the validity of the method by comparing results of calculations with previously observed displacements in laboratory models. The availability of such a verified technique of reservoir analysis would afford major advantages. First, it would demonstrate that the fundamental macroscopic concepts of two-phase fluid mechanics, i.e., relative permeability and capillary pressure, yield an adequate description of the physical process. Also, since most reservoir rocks appear to be water-wet and contain connate water along with oil, it would provide a method of technical and economic value for calculating the course of oil displacement by water directly from measured reservoir and fluid properties. It is important to emphasize that the calculation is subject only to the limitations of detail and precision of reservoir information, but not to limitations introduced by simplifying assumptions. Further, it would providc almost the only means of examining the influence of factors such as the size and extent of reservoir inhomogeneities and uncertainties in the basic reservoir data. Knowledge of this influence is essential in stating quantitatively the detail required to define a reservoir and in establishing the relation between the uncertainty in the definition of reservoir properties and the reliability of predicted performance. Moreover, in the process of solving a particular problem much detailed information would become available about the displacement process. For example, at each point in the reservoir for all stages of the displace ment. the calculations would yield not only the water and oil saturations but also the direction and magnitude of fluid velocities and the local fluid mobilities. Such dctail is potentially of great value in giving insight into the mechanics of particular displacements. The development of such a method has long been the goal of research in the application of numerical an-alysis to petroleum reservoir enginecrinz. The most complete treatment of the displacement process published to date is that of Douglas. Blair, and Wagner,&apos; which, however, was limited to flow in a single dimension. The method presented in the present work is hascd on the numerical solution of a finite difference analogue of the multi-dimensional differential system describing the displacement process. Although current work has considered only displacement of oil by water from water-wet sands, the differential system for other immiscible displacements, such as gas displacing oil with which it is in phase equilibrium, is quite similar. It should therefore be expected that the technique described will be applicable to displacement by gas as well. The description of the simultaneous flow of fluids through porous media in terms of relative perrncability and capillary pressure has been adequately discussed in the literature and standard textbooks. Sec, for exampje, Muskat. Chapter VII.&apos;

By R. H. Winn

In this paper a heterogeneous carbonate reservoir is considered as a succession of layers of formations of radically different porosities, permeabilities, water saturations, and rock matrix types; i.e., the heterogeneity is vertical rather than radial to the wellbore. Presumably each layer is more or less homogeneous. To determine the "net oil in place" in this reservoir it is desirable to know the porosity and water saturation of each layer. In addition, the section must be subdivided into that which will produce oil, that which will produce water, and that which will produce little or nothing. In numerous wells drilled in these reservoirs radioactivity surveys, guard electrode surveys, and caliper surveys have been made. These logs have been compared with core analysis data, when available, and the analysis of the surveys compared with production data. This study, still in progress, is intended to provide improved analytical techniques if such are possible. This paper is a progress report on the work. DETERMINATION OF POROSITY The neutron-gamma log has long been recognized as a measure of hydrogen concentration.1,2,3 In reservoirs that are free of clay, shale, or other hydrogen containing matrices, it has been accepted as a measure of porosity.4,5 Empirical methods to relate relative neu-tron-gamma intensity to porosity are often employed." To provide a more precise determination of porosity from the neutron-gamma log each instrument is calibrated immediately prior to each survey by a method which refers all tools to a hydrogenous cylinder. To insure stability a calibration check is made after each survey. These calibration records are printed as an integral part of the log that is recorded in standard counts per second. A detailed description of the calibration procedure is available in the literature.&apos; The procedure employed insures that each Survey is numerically reproducible within the limits of statistical variation. To relate the standard neutron counts per second to porosity and hole size, records were made in test wells constructed of blocks of limestone. The porosities of the blocks were accurately measured and the blocks completely saturated with fresh water. Fig. 1 presents some of the results obtained in these test wells.&apos; The lines shown in Fig. 1 were obtained by deriving an empirical equation relating the 11 points shown so that the relationship may be projected to larger and smaller hole sizes. A detailed description of the tool is available in the literature.&apos; Field tests indicate that the tool is adjacent to the wall of the hole most of the time when the surveys are made in uncased holes drilled with saline muds. In this circumstance porosity may be calculated from Fig. 1 if the hole size is known. When fresh muds that form thick mud cakes are employed, the centralizing effect of the mud cake must be considered and the porosity determination is less reliable. In cased holes the combined effect of variations in hole diameter and the unknown eccentricity of the casing in the hole may make porosity determinations extremely unreliable. In any event, an accurate knowledge of hole size is essen-

Jan 1, 1958

By H. R. Hoffman

SINCE slag is a necessary product of the reactive oxygen additions necessary to the present-clay quality steelmaking, the study of the control of its volume is being attempted. With other varying factors that may affect the volume of slag kept as nearly constant as possible, the object of this investigation is to determine what effect the one factor of varying the amounts of iron-ore additions and the time of the additions may have upon the volume of slag in producing an acid electric steel heat.

Jan 1, 1947