Search Documents

By Fabrice Mathieu

The Cutter Soil Mixing (CSM) provides a cost effective solution for the rapid construction of retaining and cut-off walls using new equipment developed from diaphragm wall cutter technology. CSM consists of cutting and mixing drums mounted on compact hydraulic motors. Soletanche Bachy CSM has been designed to leave the space above the tool free, thereby mixing the soil efficiently during all the phases of the wall construction, with high penetration rates. The precise positioning and verticality of the wall is achieved using a kelly bar and full monitoring. Soletanche Bachy CSM is a versatile equipment which can be mounted on various carriers: pile rigs, hydraulic crane, carrier equipped with telescopic mast. The major phases of Soletanche Bachy CSM development are presented, including the results of an extensive trial carried out in Le Havre (France). The soil consists of hydraulic fill with soft soil lenses overlying sandy deposits. 20m deep panels were constructed to support a rectangular shaft. During the construction, and after its completion, the shaft was subjected to an extensive series of tests followed by a partial excavation. The paper discusses also the future development of the technique and its potential applications.

Jan 1, 2006

By R. A. Bullivant

Roger Bullivant Piling Limited has started 1992 with the introduction of the CONE PILE into its range of precast concrete foundation techniques. Since the establishment of its Piling Division ten years ago, alongside the original Underpinning Company, a commitment to innovated development has seen a steady growth in Roger Bullivant's activity in piling, ground treatment and general foundation engineering. Over the last four years, £1.2 million has been invested by the Bullivant Piling Division into research and development in the field of precast piling and other foundation systems. The goal has been to develop economically attractive systems tailored to our clients design requirements and, wherever possible, unique to Roger Bullivant Piling.

Jan 1, 1992

By Drew Floyd

Five full-scale pile load tests were performed on pairs of PZ-22 sheet piles installed with a vibratory pile driving hammer. The sheet piling was installed in several locations in soil generally consisting of miscellaneous granular fills overlying soft organic silts, inorganic silt interbedded with sands and gravels, very dense glacial till and shale bedrock. The test program also included the use of tip tell tales to determine what capacity could be attributed to tip resistance and skin friction. During the design phase of the project, it was assumed that the capacity of the sheet piles driven with the vibratory hammer could be correlated with the rate of penetration. The correlation between vertical capacity and rate of penetration would be used as a basis for determination of a driving criteria from driving the production sheet piling. The sheet piling load tests demonstrated that it was not possible to correlate the capacity of sheet piling driven with a vibratory hammer and the rate of penetration. It was also demonstrated that the capacity of the sheet piles was directly related to the density of the soil at or just below the tip. The results also tend to agree with empirical equations provided by Meyerhof (1976).

Jan 1, 1989

The Effect of Molecular Weight on the Adsorption and Efficacy of Polysaccharide Depressants

Sep 13, 2010

By M. Slatter

The need for anti-corrosion coatings has existed for many years in the ground support industry, but the application requirements have made coating selection limited. Varying groundwater and chemical conditions continually challenge long term coating performance. Traditionally the industry coating preference has been hot-dip galvanizing due to its performance characteristics in highly corrosive environments and low cost nature. However, the galvanized coating has application limitations. This paper highlights some of these limitations and provides selection criteria for a new organic coating developed for one such difficult application, DSI?s Omega BoltPTM Pwhich is an expandable ground support. [ ]

Jan 1, 2009

How did you get into mining; were you from a mining town or mining family? Not at all. I grew up in northwest Kansas. I liked to hunt and fish, so I thought it would be fun to work for a company that made knives or guns. It seemed like metallurgical engineers would be something those companies could use, so I started in physical metallurgy. I got a summer job at the great Climax molybdenum mine near Leadville, CO shoveling muck onto conveyors. I was hooked. I loved everything about mining, so in the fall, I changed majors from physical metallurgy to mineral processing. For many years you actually discouraged young people from studying the mining disciplines. Could that be right? That’s true.

Jan 1, 2007

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (KO88) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron- and steelmaking and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By M. Mets

Pile foundations have been used in Estonia since the beginning of 1960's. To evaluate the capacity of piles nearly 2,500 pile tests and 1,800 pile loading tests Have been carried out. The pile foundations of nearly 150 houses are under settlement observations.

Jan 1, 2000

By Henk van der Bijl, Sean Rogers, Eugene Sidorski, Alan Carpenter

The electrode column is the heart of the submerged arc furnace. Superior electrode performance provides improved furnace performance. This paper describes the main features of the electrode column that delivers superior performance in furnaces worldwide, developed by Pyromet. Pyromet?s electrode comprises the compact slipping device, lower electrode assembly, upper and lower mantles, self-adjusting electrode seal, paste heaters, and Pyromet?s patented innovative electrode breakage detection and length determination system. Pyromet?s slipping device features compact interlocking clamping rings, incorporating fail-safe spring-loaded design. The interlocked clamping rings distribute the clamping force over a larger area of the electrode casing, preventing damage. The slipping device assembly features a low maintenance modular design that allows rapid slipping cycle times, back slipping, and compatibility with Pyromet?s electrode breakage detection and length determination system. Pyromet?s lower electrode assembly consists of the contact shoes, pressure bellows, pressure ring and heat shields. The contact shoes and pressure ring are designed for long, trouble free operation whilst the pressure bellow configuration equalise contact pressure and current distribution. Furthermore, the contact shoes incorporate a self cleaning feature, ensuring optimum electrical contact. The segmented design offers easy maintenance. Pyromet?s clients experience less down time due to longer component life. Pyromet?s remote adjusted electrode seal assembly reduces the rope seal working temperature, increasing rope life. The self compensating rope seal clamping force ensures an effective seal as the rope wears. Pyromet?s electrode breakage detection and length determination system detects electrode breaks utilising Pyromet?s electrode holder and data processing system. The length measurement system controls electrode length, eliminating the occurrence of short electrodes. The length measurement system furthermore eliminates the need for manual electrode length measurement, reducing associated production losses during furnace burn downs.

Jan 1, 2007

By R. L. Grayson

In 2010, MSHA began holding hearings on a new coal mine respirable dust rule, which proposes a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the ?hot spots? where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines? compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, seam height, and selected ?hot spot? counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications on the need for better dust control methods.

Jan 1, 2012

By J L. Carpenter, S M. Iveson, K P. Galvin

Wet beneficiation of iron ore fines less than 1 mm typically involves a desliming stage ahead of the fine gravity separation such as spirals. The desliming is achieved using a bank of cyclones. The reject ultra-fines emerge in the overflow stream at relatively low pulp density, contain high proportions of low-value slimes, but also well-liberated iron ore ultra-fines below 0.045 mm in size; however, recovering the valuable iron ore ultra-fines from this overflow stream presents a significant challenge due to the need to remove such a large amount of water and slimes.The REFLUX™ Graviton consists of distinct 3D-printed modular units, based on REFLUX™ Classifiers, which are rotated at high speed in a large centrifuge. This system has previously been investigated under semi-batch conditions, demonstrating the potential for precision separations with significant capacity. It has been shown that the throughput advantage of the inclined channels and G forces multiply. This is the first paper presented showing the performance of this system under continuous steady-state conditions. Ultra-fine silica in the size range of 0 to 0.045 mm was fed to the Graviton at different volumetric rates, fluidisation rates and pulp densities ranging from 2 wt per cent to 30 wt per cent, in order to develop a fundamental understanding of the system’s performance. Experiments were then repeated using ultra-fine iron ore.CITATION:Carpenter, J L, Iveson, S M and Galvin, K P, 2017. Separation of ultra-fine particles using the REFLUX™ Graviton, in Proceedings Iron Ore 2017, pp 141–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G. Velarde

This paper presents the metallurgical results of column and stockpile leach tests with forced aeration to determine the usefulness of this process in the operational leaching at Sociedad Minera Cerro Verde S.A.A. The evolution of the aeration system is presented and also an innovative solution developed to overcome forced aeration’s main problem, which is the early obstruction of the aeration pipes located at the base of the stockpile, causing a decrease in air and oxygen levels and therefore a reduction in the metallurgical benefits.

Jan 1, 2006

Extraction of copper from a chalcopyrite concentrate by means of a cupric chloride leach is described. Initially the concentrate is mixed with sulphur in a 9: 1 ratio, and heated to 350-400°C. This converts the chalcopyrite into more readily soluble sulphides, while the iron rejected from the chalcopyrite is transformed to pyrite, which is insoluble in the leach solution employed. A two-stage countercurrent leach using a leach solution of 1 M cupric chloride, 3.5 M sodium chloride, and 1 M hydrochloric acid extracts 98 per cent of the copper, if conducted at 105°C. Iron extraction is relatively low, the mole ratio of iron to copper extracted being 0.17, compared to 1.0 for unreacted chalcopyrite. After dissolution, copper can be recovered by electrolysis, cupric chloride leach solution being regenerated at the anode.Electrolytic power requirement is low, being approximately 0.5 kWh per kg of copper. The sulphur and, most of the iron entering as feed are rejected from the process in the form of pyrite, which remains in the leach residue.

Jan 1, 1974

By A. H. Winckers

"The San Nicolás deposit is a complex fine grained polymetallic volcanogenic massive sulphide deposit located in central Mexico.Metallurgical testwork was carried out in 1999 and 2000 to develop a flowsheet. During the course of the metallurgical testwork it became evident that it would be impossible to develop an accurate head gradehecovery based model for the projection of metallurgy. It was suspected that variability in mineral texture was a predominate factor affecting metallurgy. For this reason it was decided to evaluate the applicability of QEM*SEM technology to this test program.This paper summarizes the metallurgical testwork and describes the evaluation and subsequent application of the QEM*SEM technology to characterize the mineral texture throughout the deposit. Finally it is shown how the QEM*SEM data are used in the mine block model to project the metallurgy.The QEM*SEM (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) is an automated image analysis system developed by CSRO which provides quantitative numerical estimates of the compositional and textural properties of the mineral suite which govern the concentration process.INTRODUCTIONThe San Nicolás deposit, was discovered in 1997 through the application of geological and geophysical techniques. The property lies 60 km southeast of the city of Zacatecas on the central Mexican plateau as shown in Figure 1."

Jan 1, 2002

By A. Broussaud, J. D. McKay

Benefits analysis of adaptive Expert control systems operating at plants in Africa and the United States are presented. Proper statistical tools and techniques are discussed. Technical and practical pitfalls of strategy comparison are also presented and illustrated with from published data. Advantages and disadvantages of a “Pay for Performance” approach to a project are reviewed.

Jan 1, 2001

By Carl Heinrich

I HAVE read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: Horn Silver Slags Oxygen(b) Oxygen(b) Average of I and. II Slag I percentage Slag II percentage Oxygen Si02 33.9 18.1 .35.0 18.7 34.50 18.40 FeO 26.8 6.0 25.4 5.7 26.10 5.80 CaO 26.1 7.5 24.9 7.1 25.50 7.30 BaO 3.2 (a) 0.3 3.2 0.3 3.20 0.30 A1203 10.8 5.1 9.3 4.4. 10.05 4.75 100.8 37.0 97.8 36.2

Jan 10, 1916

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By A. M. Cummings

Each mining district presents different problems as to the methods of ore extraction cad underground support, which are dependent upon the type of the ore deposit and the character of the inclosing rock. Mining costs, however, depend largely aeon the efficiency with which the methods employed underground are [applie] as well as upon the selection of the method best adapted to the physical conditions. The purpose of this paper is to present to the operator in other districts a detailed description of ho mining method used ins results obtained in tie exploitation of the bedded magnetite deposits of the Mineville district. The town of Mineville is situated in the Adirondacks, five miles west of Port Henry on Lake Champlain.

Jan 1, 1928

By M. Ayhan

Drums of a modern longwall shearer are manufactured to include various constructional features conveying extracted material onto the face conveyor as efficiently as possible. Designing a drum with a conical shell or with reduced vane length, consequently with a stepper vane angle, is the most widely employed method in an attempt to increase loading efficiency. This study compares loading performances of two such drums, one having a conical shell with modified loading vanes, the other with a cylindrical shell with reduced vane length. Firstly, the loading performances of drums are predicted and the maximum haulage rate attainable with the drums are calculated. Then the performances of drum are compared by long-term comprehensive underground trials with coal shearers under similar conditions during the production operation of Park Termik Cayirhan coalmine in Turkey. Although higher loading performance is predicted for cylindrical drums, the in situ trials point out that Globoid drums have a slightly higher loading performance than cylindrical drums. Furthermore, the relationship between operational variables, i.e. extraction height, sumping depth, haulage rate and in situ loading performance, were investigated statistically on the basis of data gathered during the underground trials. Keywords: longwall mining, shearer drums, loading performance.

Jan 1, 2006