Search Documents

By Bernard H. Hertlein

All methods of deep foundation construction present challenges to the contractor and engineer that vary according to the method employed, and the geotechnical conditions in which it is being used. Augered-Cast-In-Place (ACIP) piles are generally regarded as one of the most challenging, because the construction method precludes the use of traditional shaft inspection and quality control techniques. Application of Nondestructive Test (NDT) methods can provide quality control for ACIP shafts that traditional methods cannot, but each NDT method has limitations. These make some NDT methods unsuitable for use on ACIP shafts, and may limit the effectiveness of others, depending on geotechnical conditions. To help contractors and engineers working with ACIP piles select the test method most appropriate to specific site conditions, this paper presents a summary of the major NDT methods currently available, and reviews their capabilities with respect to the unique conditions presented by ACIP pile construction. Case histories illustrate how a combination of careful method selection, skilled data interpretation, and experienced engineering judgment have resolved problems and ensured quality in foundation construction by discriminating between potentially serious defects, and those that are unlikely to be significant.

Jan 1, 1997

By R. D. Leitch

"INTRODUCTION The character of mine drainage from areas of low pyritic coal3 and from average pyritic coal4 has been investigated, and to complete the study it seemed desirable to select a number of mines situated in high pyritic are as to determine whether or not this variation determines the relative acidity of drainage from mines operating in these characteristic coal fields. Advantage has been taken of some worked on in 1918 by Henry Leighton 5, then Professor of Economic Geology, University of Pittsburgh. He visited and has reported certain areas of high pyritic coal which we also visited during this study. Many of the mines were found to be idle in 1930 and a few were caved shut, apparently for several years. However, samples of the outflow from all mines visited were collected if possible and analyzed, and some general information was gathered for each mine. The map (fig. 1) shows the location of these areas as given by Leighton.ACKNOWLEDGMENTSThe information and assistance obtained from officials and others at the mines visited during this study are gratefully acknowledged, as well as the original suggestion from Dr. Glenn V. Brown of the State Sanitary Water Board who called attention to the desirability of such a study.Thanks are also especially due the coal laboratory of the United States Bureau of Mines, under the direction of H. M. Cooper, for the analyses and determination of sulphur forms in the large number of solid samples necessary to the work reported,This study has been carried on under the direction of R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station, of the U. S. Bureau of Mines."

Jan 1, 1932

By V. D. Jalevsky

A new methodology of an experimental-analytical approach has been developed. It is used in building an information geomechanic monitoring system for the modeling of geomechanic processes during coal seam working. The approach synthesizes experimental (in-situ) measurements of rock pressure manifestation in separate points, methods of numerical modeling of processes on rock boundaries with coal, and a seam analytical calculation of rock mass in a spatial strained state. One of the realizations of this approach is the developed theory and calculation method of adjoining rock surface shift (overhang) formation during underground working of sheet deposits and of rock mass geomechanic state determination. There are description algorithms of cavity configurations with broken lengths of faces during underground working of useful mineral sheet deposits. These algorithms have been used in computer modeling of formations of adjoining rock surface overhangs and abutment pressure upon rock mass in the area of coal faces with irrectilinear longwalls. Peculiarities of surfaces shifts and stress allocation are established for different face schemes. The use of theory and methods alloww working out techniques of automatic control to receive processing algorithms of RPM measurement results and calculate geomechanic situations within panels in the process of planning and development as well as during mining, i.e., to carry out long-term prediction, in-line control, and short-term prediction of rock pressure manifestations.

Jan 1, 1996

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

At Great Boulder Gold Mines Ltd. a number of attempts were made to remove water soluble copper and iron salts from calcined pyritic concentrates but variou~ problems arose and the methods were abandoned.A method of rapid washing has been developed and although some problems still exist a workable process was established which resulted in substantial savings of reagents used for the cyanidation of calcine.INTRODUCTIONIn the Great Boulder flowsheet crude ore is ground in cyanide solution, then thickened, agitated and subjected to two stage filtering. Secondary filter discharge is pulped with flotation circuit water, gassed with sulphur dioxide to precipitate soluble gold and activate pyrite, and after the addition of copper sulphate and xanthate, the pyrite and tellurides are recovered by flotation. Flotation tailings are thickened and pumped to the disposal area and concentrates are calcined in Edwards roasters. Calcine is washed to remove water soluble copper and iron salts and the washings pumped to the flotation section where the copper is used as an activator. The washed calcine is cyanided and returned to the crude ore circuit via the thickeners. Solution for precipitation in the Merrill Crowe is drawn from the crude ore thickeners.Prior to the introduction of calcine washing the calcine contained 7 lb/ton copper of which approximately 60 per cent was water soluble. It also contained approximately 90 lb/tol'l of water soluble iron salts. Both the copper and...

Jan 1, 1964

By Jacob Masliyah, Zhiang Zhou, Dharamdat Christendat, Tshitende Kasongo, Kevin Hyland, Zhenghe Xu, Ted Kizior, Douglas Cox

"A novel on-line visualization system, previously developed at Syncrude Canada Ltd., has been modified to characterize rising bubbles, particles and particle-bubble aggregates in a flotation process. With this system, the bubble size and rise velocity in a laboratory flotation cell can be determined. The technique allows the loading of solids on bubbles to be visualized, thereby providing an in-depth understanding of sub-processes of flotation. A step-by-step data processing procedure is presented. The applicability of the developed system to mineral flotation and bitumen extraction is discussed. Under batch flotation conditions in a laboratory Denver cell, three main bubble-particle attachment patterns are observed. They are: i) single particles attached to single bubbles, ii) particle aggregates loaded on single bubbles; and iii) a group of particles aggregated with a group of bubbles. The results demonstrate that the on-line visualization system is a powerful tool for understanding and diagnosing flotation processes.INTRODUCTIONAir (Gas) bubbles are an indispensable component in a flotation system. Both industrial practice and theoretical analysis indicate (Yoon, 1993; Diaz-penafiel and Dobby, 1994) that the size and population of bubbles are two important process parameters in modeling flotation. More recent investigations (Finch, et al., 1999; Gorain, et al., 1997) suggest that for a given flotation system, bubble surface area flux, defined as the air liquid interfacial area per unit time and unit cross-sectional area of flotation cell, showed a better correlation with the flotation rate constant. As a result, the bubble surface area flux is now being considered as a key parameter to account for the combined effect of bubble size and population in evaluating the performance of flotation machines and modeling flotation processes. However, the success of using bubble surface area flux in flotation process modeling largely depends on how accurate it can be determined or estimated (Finch, et al., 1999)."

Jan 1, 2000

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By R Byrnes, P Hensley

The outstanding environmental management initiatives undertaken by Novacoal at its Western Main Site near Lithgow in New South Wales over the past five years are detailed in this paper. These initiatives have been based on a combination of proven and innovative investigation and implementation techniques, close consultation with regulatory authorities and full support by colliery management. The results of these initiatives have enabled the colliery to exceed its pollution control obligations from a base well below industry standards. The initial poor condition of the mine was the result of over 50 years of traditional mining which paid little regard to environmental management. The transformation of the colliery within such a short period, with limited capital, is considered a model for the N.S.W. coal industry.

Jan 1, 1995

By Graham W. Gibbs

The current state of knowledge concerning mesothelioma risk estimates is reviewed. Estimates of the risk of mesothelioma exist for the commercial asbestos fiber types chrysotile, amosite and crocidolite. Data also exist on which to assess risks for winchite (sodic tremolite) and anthophyllite asbestos. Uncertainty in estimates is primarily related to limitations in measurements of exposure. Differences in the dimensions of the various fiber types and of the same fiber types at different stages of processing add a further complication. Nevertheless, in practical terms, crocidolite presents the highest asbestos related mesothelioma risk. The risk associated with sodic tremolite (winchite) appears to be similar. In chrysotile miners and millers, the mesothelioma risk has been linked with exposure to asbestiform tremolite. Exposure to chrysotile in a pure form seems likely to present a very low if any risk of mesothelioma. While the majority of mesothelial tumors result from exposure to the asbestos minerals, there are other well established and suspected etiological agents. While a practical threshold seems to exist for exposure to chrysotile, it is unlikely to exist for the amphibole asbestos minerals, especially for crocidolite. To date there is no indication of an increased risk of mesothelioma resulting from non-commercial fiber exposure in the taconite industry. © 2007 Elsevier Inc. All rights reserved. Keywords: Mesothelioma; Amosite; Grunerite; Taconite; Crocidolite; Tremolite; Anthophyllite; Winchite; Risk estimation; Etiology

Jan 1, 2007

By C. A. Ozturk

The compressive strength of rock (sc) has an important effect on design of structures in rock engineering. Compressive strength can be determined in the laboratory using the uniaxial compressive strength (UCS) test. Some other index tests, such as the point load test, are also used, particularly when suitable samples for UCS are not available. The quantification of rock texture has introduced a new method in rock engineering for estimating the mechanical and physical properties of rock materials from microscopic investigations. The aim of this study is to quantify rock texture to estimate rock strength from the texture coefficient (TC), which is determined from a statistical assessment of thin section images. Rock texture is quantified by twelve different images from a single thin section to increase the reliability of texture analysis. A data-set is prepared to investigate correlations between TC and sc. The statistical correlations are computed after classifying of the rock samples based on their lithology as well as grain features. Equations derived based on the results of this study are used to predict the approximate value of compressive strength from the texture coefficient. This method is particularly useful for preliminary studies in rock engineering projects prior to detailed site investigation.

Jan 1, 2014

By Lily Ruíz

El presente texto evalúa el relave minero de SIMSA con el objetivo de obtener un producto ecológico que pueda ser utilizado como mejorador cationico de suelos y restaure el equilibrio de los suelos ácidos de la selva peruana. Para ello, se desarrolló un trabajo a nivel de laboratorio, obteniéndose resultados satisfactorios. Posteriormente se pasó al nivel piloto donde a través de la experimentación se utilizó el relave en diferentes concentraciones para la producción agrícola y forestal, reafirmando los resultados en las mejoras de la productividad en suelos ácidos.

Sep 9, 2007

By Craig C. Johnson

The purpose of this effort was to investigate the feasibility of employing a piezoelectric transducer for seismic communications applications in mine environments. The transducer, a government furnished device incorporated a high Q, spring-mass resonator to load the air side of the piezoelectric crystal. The resonant frequency was seismic load dependent and fell in the range of 300 to 340 Hz. The effort included a mathematical analysis of the transducer, with corroborative laboratory tests, together with actual communications experiments performed first in an open-formation limestone quarry and finally in an operating iron mine. This work showed that the transducer could be coupled efficiently to hard, competent rock media with power conversion efficiencies of 70 to 80 percent (electrical to mechanical) in typical installations. In the iron mine, when radiating peak power was about 30 W (acoustical) in a gated pulse mode, signals were received at a distance of 760 ft through a massive rhyolite porphyry formation. This represents a 15% radiation efficiency with an input of 200 watts. Despite the high ambient noise level due to operating mine machinery, a signal-to-noise ratio of about 20 dB was achieved using a very narrow band filter to process the received signal, and a data rate of about two pulses/sec was demonstrated.

Jan 1, 1972

By R. Sharon, P. M. Hawley, X. Ochoa

"Development of Barrick Gold’s Pierina gold mine in north-central Peru requires construction of a waste dump for disposal of nonore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low-quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high-quality, hard, durable, blocky waste rock.A hybrid dump design concept was developed that requires in-pit segregation of highand low-quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included.This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems."

Jan 1, 2003

By Eric E. Cather

In 1984 and 1986, at the request of the U.S. Forest Service, the U.S. Bureau of Mines conducted a mineral appraisal of the 315,000-acre Lemhi Range study area. This area is located in Lemhi and Custer Counties, about 25 mi south of Salmon, Idaho, and is in the Northern Rocky Mountain physiographic province, Topography is generally rugged with elevations ranging from 5,600 ft to about 11,350 ft above sea level. Since the 1880's, approximately 500 mining claims have been located within the study area; about 400 were current at the time of this investigation. Also, part or all of 12 patented mining claims are in the study area. During Bureau field work, forty-four mineralized sites were examined. The sites had been explored by 80 adits, 14 shafts, and about 140 pits and trenches. At least five properties in the study area have had significant production; the adjacent Mohawk, Grace Phelan, and Snowbird claims had a combined total of 136,000 oz of silver and 67,000 lb of lead; production at the Brown Bull was about 14,800 oz of silver and 115,000 lb of lead; the Portland mine yielded an unrecorded amount of silver. The Hilltop mine, located a few hundred feet outside the study area, produced 125,000 oz of silver, 2.7 million lb of lead, 87,000 lb of zinc, and 62,000 lb of copper from mineralized zones that might extend into the study area. More than 10,000 lb of copper were produced at the Blue Jay mine from workings located about 1,000 ft outside the study area. The Bureau of Mines investigation did not reveal the presence of identified resources in the study area. However, several areas contain mineralized sites and are known occurrences. Some of these warrant additional work to further delineate the mineralization and possibly determine identified resources.

Jan 1, 1988

By J. C. Edwards

A series of four coal combustion experiments (I)' was conducted at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory in the Safety Research Coal Mine to evaluate the response of optical and ionization smoke and CO sensors to a small 0.61 m square smoldering coal fire which transitions to flaming combustion in the presence of diesel emissions. With the increased utilization of diesel engines in underground coal mines, it is important to be able to discriminate fire products-of-combustion (POC) from diesel emissions. One proposed method to accomplish this is the deployment and interpretation of multiple sensors.

Jan 1, 2010

By Ian Hutchison, Ted Sluder, Jack Caldwell, Don Moore

Introduction The Cannon mine at Wenatchee, WA has recently been brought into operation to recover gold from the sandstones of the Swauk formation. The mine is a joint venture between Asamera Minerals (US) Inc. and Breakwater Resources. A tailings impoundment was constructed to impound 2.7 to 3.6 Mt (3 to 4 million st) of tailings at 1.8 kt/a (2000 stpd) over about five years. This paper describes the design and construction of the impoundment. In particular, it describes the 100 m (300 ft) high earthfill embankment that is the main feature of the facility. Project environment The project is located on the outskirts of Wenatchee, a town of about 40,000 people. The town is situated on the flat alluvial terraces beside the Columbia River. The Cascade Mountains rise from the terraces in a series of ridges and valleys. The mine is at the foot of the Cascades. The tailings impoundment is in one of the steep valleys. The climate is mild and dry (Table 1). Site selection Twelve alternative sites within a 16-km (10-mile) radius of the mine were examined. Decision making theory was used to select the most suitable site. Advantages of the chosen site include its proximity to the mine and its low visibility from points of common public access. Also, the area was already heavily impacted by an existing silica quarry. The major disadvantage of the site is the need to pump tailings over a distance of 1.5 km (1 mile) and against a static head of 200 m (655 ft). Also, it is located in a gulch just upstream from the town of Wenatchee. Site geology The impoundment is generally underlain by interbedded sandstones and siltstones. The siltstones are often shattered. The sandstones are often friable. Both rock types are extensively jointed. Some isolated faulting of the sediments occurred before the area was covered with basalt flows. About 10,000 years ago, at the end of the ice age, the basalts were covered by 3 to 10 m (10 to 33 ft) of wind blown loess - a fine sandy clay and silt. River deposits filled the base of the valley to depths between 5 and 25 m (16 and 82 ft). Under the main part of the embankment, these materials were removed to expose bedrock. Ground water flow is generally through the more permeable layers. The permanent water table is about 5 m (16 ft) beneath the ground surface. Project and impoundment layout Figure 1 shows the layout of the mine, the mill, and the tailings impoundment. The tailings deliv-

Jan 8, 1986

One would anticipate that after 40 years in the mineral industry it would be simple to project the trends at least 5 or 10 years into the future. However the last 20 years, 1950-1970, have been so different in the mineral industry from the years 1930-1950 that I suggest only 20 years or so are relevant to any forward projection.Those, of us that have been about during the last 40 years find it hard to relate the two periods.The first with the depression, low base metal prices, attempts to revive the gold industry, very little export of minerals, and finally World War II and the recovery period.The second, a period of unimagined discoveries and the reappraisal of a wide variety of minerals and metals-iron, coal, bauxite, beach sands, manganese, oil and gas, and nickel, to name but a few.The second period started early in the 1950s and was triggered off by the search for oil in Australia.Rough Range No. 1 was an important milestone in our history because it initiated a series of speculations and the re-examination of much of our thinking about our mineral resources. It lead to the discovery of bauxite and the start of a flourishing aluminium industry.The realization of the extent of the iron ore resources was another, major step and the influx of overseas capital and competence started the large wave of development made effective by the Japanese markets.The momentum of the late 1950s has carried us to where we are today and will undoubtedly carry us further forward in the next few years.All this development in the mineral industry has come at a time when our pastoral industries have reached a difficult period. I have no doubt that if it were not for the mineral industry Australia would at the moment be experiencing one of its blackest eco...

Jan 1, 1971

By Andrew Chapman

The scope of the SA (Situational Awareness) working group is to analyze the effectiveness of information delivery systems in mining equipment and develop a unified display design, to mitigate against the proliferation of screens within equipment cabs. This working group comprises a variety of stakeholders representing a cross-section of relevant mining and mining-related organizations. This stakeholder network will help guide the direction of the working group towards a common, mutually beneficial end. For now, the focus is on shovel displays; however it should be noted that this work is expected to form the foundation for similar work with other equipment in the future.

Aug 1, 2013

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By P. F. Allen

WITH capacity of 51,000 tpd, the Morenci concentrator produces approximately 49,000 tons of tailing for final deposition. Disposal involves distribution of thickened tailing to dams in such a manner that solids can be used for dam construction and water can be impounded for reclamation. During early operation, although tonnage treated was lower, it was necessary to use orthodox disposal practices in the areas available for tailing. Trestles mounted on a series of dams, constructed of borrow material, carried the pipelines from which tailing were spigoted behind the dams. When adequate disposal areas were finally established, it became desirable to look for more efficient methods. The idea of placing the distribution pipe or manifold directly on the crest of the dam was advanced in 1945. After a period of testing, that procedure in modified form replaced the older trestle arrangement. Marked economies resulted, and time required to prepare dams for succeeding storage cycles was greatly reduced. The tailing disposal area for the Morenci concentrator lies south and southwest of the concentrator building. Ample storage space is available. A wide valley contains three sharply defined ravines lying on an average slope of 4 pct. The more central of these ravines, and the largest of the three, is known as Morenci canyon, which provides substantially more tailing storage area than the other two. Stargo canyon lies to the west; the other is appropriately named East canyon. Total area of the tailing disposal site is nearly 31/4 sq miles, or about 2000 acres. The storage area in use was somewhat more than 850 acres at the end of 1954, or 16 acres per 1000 tons of tailing to be stored daily. At the present time none of the east side dams are in regular use but they are available in emergency. There are five dams on the west side (in Morenci and Stargo canyons) as well as two auxiliary dams adjacent to No. 4 West and No. 5 West. This has made it possible to concentrate men and equipment in a smaller area with consequent savings in both manpower and machinery. Tailing Thickening: Tailing from the flotation process reaches the thickeners with a solid content of about 18 pct. The launder carrying this pulp is subdivided at a central point into seven launders carrying a proportional share to each of seven tailing thickeners, which are located in Morenci canyon close to the concentrator. Five of these thickeners are 300 ft diam and two are 325 ft diam. Thickeners are of the peripheral traction type and rakes travel at the rate of one revolution in 37 to 39 min. The entire installation provides 500,000 sq ft of settling area, or approximately 101/2 sq ft per ton of tailing to be thickened daily.

Jan 1, 1957