Search Documents

By E Selvapandian, R Barr

Arrium (previously OneSteel) initiated a desktop study into the performance of its hematite ore beneficiation plant in early 2010. The beneficiation plant utilises jig concentrators and spirals to upgrade low-grade hematite recovered during mining at the Iron Duke (ID) mine site located 60 km south-west of Whyalla. The study, conducted in conjunction with Mineral Technologies, identified a number of opportunities for improvement, which were validated by a series of sampling campaigns and a pilot plant trial. One of the major recommendations was to upgrade the ultra-fines processing circuit from a single-stage spiral circuit to a three-stage circuit. The upgrade of the ultra-fines circuit was estimated to provide a significant increase in fines production and grade.In order to capitalise on the strong iron price at the time of the project, Arrium decided to utilise a fast-tracked approach to design, construct and commission the processing equipment required to achieve the improvements identified. This decision introduced the risk of missing critical steps in the project development process, which could have potentially resulted in major issues in latter stages of the project. In addition to the challenges introduced due to the expedited time line for project completion, this project presented unique challenges due to its brownfield nature. One such challenge faced was the integration of the new equipment and control system software.Furthermore, the importance of the ID ore beneficiation plant (OBP) contribution to the companyÆs export commitments meant the upgrade work had to occur while minimising disruption to normal operation. This decision presented a set of new challenges to an already complex project. One such challenge was the need to build and commission the new spiral circuit in isolation from the operating plant.The aim of this paper will be to highlight some of the challenges faced in a complex brownfield project such as the ID OBP upgrade and discuss how they were managed to enable the successful commissioning of the process in early 2012.CITATION:Selvapandian E and Barr, R, 2013. Managing challenges faced in the brownfield commissioning of an ultra-fine hematite processing circuit at ArriumÆs Iron Duke ore beneficiation plant, in Proceedings Iron Ore 2013 , pp 533-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Timothy C. Siegel

Accurate representation of the geotechnical resistance distribution is critical in evaluating the performance of piles and pile groups for design. A current practice is to infer the geotechnical resistance distribution based on measured changes in strain during conventional top load pile testing. Especially for drilled and bored piles, the residual load is typically assumed to be negligible both during testing and after the application of the structure load. A practical result is that the compressive structural load is anticipated to be opposed primarily by the shaft resistance with little or no mobilized toe resistance. The predicted top deflection is estimated as the combined elastic compression plus the movement necessary to mobilize shaft resistance. The development of residual load (and associated negative skin friction) results in a significantly different design condition. Negative skin friction tends to force the pile into the ground and develops residual load in the pile that contributes to the internal compressive load. Significant toe resistance can be mobilized in order to resist the combination of negative skin friction and the sustained compressive load. The pile movement becomes a function of the toe penetration required to mobilize sufficient resistance to reach a balance of forces. In an effort to study the development of residual load in augered cast-in place (ACIP) piles, the authors installed and monitored strain gages that were embedded in an 18-inch diameter ACIP pile at a site in southeast Georgia. The results of this study indicate that residual load develops over time and reaches a distribution that is consistent with the principles of the unified design of piles. It is concluded that residual load develops in ACIP piles (as well as all drilled and bored piles by the same mechanisms) and that the residual load should be considered in the interpretation of load tests and in the pile design, particularly in the estimation of the single pile and pile group settlement.

Jan 1, 2009

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures arc discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of ruining; modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mina is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By G. Zaitsev

In mining and mineral processing, ammonium and nitrate from residues of explosives and other sources are discharged to the aquatic environment. Nitrogenous compounds in mine water can adversely affect the aquatic environment. The aim of this work was to study the biological removal of nitrate from cold inorganic mine water at the pilot-scale in an operating underground mine. Seven-months pilot testing on biological removal of nitrate from inorganic mine water was successfully performed in denitrifying fixed-bed biofilm reactors. The feed to denitrification bioreactors contained 11 mg NO3--N/L. Methanol was added as an external carbon source to the denitrifying bio-reactor since the inorganic mine water contained only traces of organic compounds (<CODCr (50 mgO2/L). Nitrate removal reached 75 g NO3--N/m3/d with removal efficiencies above 95% at temperature below 4°C. Thus, removal of explosives-residues from cold inorganic mine water was shown in pilot-scale biofilm reactors.

Jan 1, 2014

By David G. Winter

The first test pile for the carrier pier and south wharf at NAVSTA Puget Sound was driven on December 27, 1989, and the final pile was tested on February 26, 1990. Implementation and modification of the test pile program were done by the owners (WESTDIV and ROICC-Everett), the engineers (ABAM and Hart Crowser), and the contractor and his subcontractor (General Manson Joint Venture and GRL). The site is located as shown on Figure 1. SUMMARY OF THE SOIL CONDITIONS A soil profile along the pier is shown as Figure 2. The soil units can be generalized as follows: ? Upper Silts - Fill, sandy silt, and clayey silt extending from the mudline to an elevation of about -80 feet; ? Intermediate Sand - A medium dense to very dense silty sand unit which is about 30 feet thick near the shore, but thins and disappears offshore; ? Lower Silts - Sandy silts and clayey silts in a medium stiff to stiff condition; ? Deep Sand - A very dense overconsolidated sandy soil encountered at an elevation of about -145 feet.

Jan 1, 1990

By J. E. Sepulveda, R. Morrow

"In full scale mineral grinding operations, the steel balls normally utilized as auxiliary grinding media get to be consumed at different specific rates, as determined by 3 basic mechanisms: abrasion/corrosion (wear), impact ball breakage and impact surface spalling, the latter relating to the removal of rather small pieces of steel coming off the exposed surface of the balls due to repetitive impact with other balls in the charge or the surrounding mill liners. In conventional ball milling applications, the clearly predominant mechanism is gradual wear by abrasion/corrosion. In the case of SAG mills, where the make-up balls may be as large as 6”f diameter, breakage and spalling mechanisms are significant contributors to total ball consumption, although not to the extent of overriding wear mechanisms.Ball wear has been well characterized by the Linear Wear Theory, as presented at the last CMP 2014. Impact breakage has been customarily monitored, at the ball manufacturing site, via Drop Ball Tests (DBT) consisting of repeatedly dropping balls from a standard height and accounting for the number of broken balls and the weight loss (spalling) of the remaining unbroken balls. When properly conducted, DBT’s should provide meaningful indications of the breakage and spalling resistance of large diameter balls. The current publication is focused on the interpretation and projection of DBT results to full industrial scale, taking into account all 3 mechanisms of grinding media consumption in SAG mills.INTRODUCTIONA thorough, quantitative understanding of the independent contribution of all active grinding media consumption mechanisms is of the highest practical relevance, particularly in semiautogenous (SAG) milling operations where ball breakage and spalling can not be ignored or neglected, as it has been normally acceptable for conventional ball milling processes. The high severity impact conditions currently imposed in typical SAG mill environments create serious challenges to the manufacturers and suppliers of large diameter (5”–6”) SAG balls, whose products must be capable of surviving such harsh operational conditions with minimum breakage or spalling."

Jan 1, 2015

By Keith A. Heasley

Numerous different instruments and techniques have been developed for the purpose of measuring rock stress and stress changes around excavations. The interpretation of the output from many of these instruments has often been problematic. This paper covers the research performed in attempting to analyze one particular stress measuring instrument called the Borehole Platened Flatjack (BPF) . The approach used in this analysis was to combine the analytical solution for the displacements around a borehole and the analytical solution for the bore- hole-platen interaction with the empirical stiffness behavior of the flatjack. The resulting model of the BPF response was then verified using measured laboratory data with very good results. In addition, techniques for applying the method to the field are briefly discussed. The major accomplishments of this comprehensive modeling and testing program are; 1) the establishment of the critical installation and site parameters of the hydraulic pressure cell and 2) the development of a systematic procedure for calibrating the cell based on the given values of these critical parameters.

Jan 1, 1989

By V. T. Dow

This report describes construction details and methods used in driving the 5490 tunnel at the Kennecott Copper Corp, property, Bingham, Utah. The tunnel will provide railroad access to the world-famous open-pit copper mine at the projected 5490 level. This publication is one of a series prepared by the Bureau of Mines to depict mining operations and techniques in various mining districts in the United States. Utah Construction and Mining Go. (formerly Utah Construction Co.), contractor on the tunnel project, began work during September 1956 and completed the project in February 1959. The tunnel is 18 feet wide, 24 feet high, and about 18,000 feet long, It will accommodate a railroad locomotive on standard- gage track. With the exception of the last 1,700 feet, the tunnel is supported by steel sets embedded in concrete lining. The 1,700-fact segment of the tunnel is supported by timber sets that will eventually be removed as the pit is deepened.

Jan 1, 1962

By A. B. Parsons

Jan 1, 1971

By Michael J. Jorgensen, Pranathi B. Aedla, N. K. Kittusamy

Risk factors associated with the development of muscu­loskeletal discomfort and disorders during the operation of heavy mobile equipment include whole-body vibration and awkward and sustained joint postures of the shoulders, neck, and trunk. Cab design may influence awkward postures of the joints, and task duration may influence duration of exposure to awkward and static postures and whole-body vibration. To reduce exposure to risk factors related to the interface between cab design and task, it may be necessary for manufacturers to address cab design. This study assessed the repeatability of a cab design checklist developed to evaluate various design characteristics that can influence exposure to risk factors for musculoskeletal discomfort. The ability of the cab design checklist to identify posture-related deficiencies of design was also assessed. The checklist was used by two administrators across 10 pieces of heavy construction equipment. Video analysis was performed to quantify postures of the neck, shoulder, and trunk; correlation analysis was used to determine whether specific questions from the checklist were associated with the identification of awkward postures. The repeatability assessment resulted in kappa coefficients ranging from 0.52 to 1.0 (good-to-excellent reproducibility) across each piece of equipment, and an overall kappa coefficient of 0.77 (excellent reproducibility) when considering all equipment together. Results from the correlation analysis showed that shoulder flexion posture was correlated with scores from the cab design checklist. However, results of the cab design checklist were not significantly correlated with shoulder abduction or awkward postures of the neck and trunk. Results suggest that the cab design checklist may be useful for identifying cab design characteristics that need further improvement and for identifying design characteristics that increase shoulder flexion. The strength of the repeatability assessment suggests that outcomes of the cab design checklist administered by different individuals may be consistent, independent of the type of equipment being assessed.

By Robert E. Hershey

1. This investigation shows that the most important beds in Claiborne County, from the standpoint of present production and reserves, are the Coal Creek and Jellico. Together, they contain 69 percent of the known recoverable reserves in the county. Reserves in five other beds are tabulated in this report; in order of quantity of reserves, they are: Blue Gem, Lower Pioneer, Pewee, Big Mary, and Rex. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 60 million tons, as of January 1, 1953. Of this total, 55 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Deepak B. Deshpande

This paper enumerates various difficulties encountered in the design and construction of deep caisson foundations for the Second Bassein Creek Bridge constructed over a creek with very difficult site conditions. The designer of the bridge had anticipated the problems associated with the construction of large diameter floating caissons and limited the maximum size of caisson to 12.5m O.D. facilitated by the means of Shock Transmission Units (STUs). This is the first road bridge in India where STUs are installed to distribute seismic horizontal loads among piers installed with fixed and unidirectional bearings. Besides the usual difficulties of tilts, shifts, and sinking in the construction of floating caissons, the paper also describes a novel methodology used to retrieve a circular 12.5m O.D. caisson which had been swept away during a storm and stuck into the creek bed.

Jan 1, 2002

By Felix Cheng

Extensions to the Convention Centre in Adelaide, South Australia consisted in part of construction over the existing railway system comprising nine rail lines and passenger platforms. Vibro-pile (Aust) won the design and construct tender with a solution comprising over 500 cast insitu concrete piles. The pile types were 500 to 900mm diameter non-displacement CFA piles and 400mm diameter displacement V-piles. The V-pile is a cast insitu screw pile developed by Vibropile (Aust) Pty Ltd. Both pile types were installed with minimal noise and vibration required for the project, while the displacement V-pile had the advantage over the CFA pile by developing the same pile capacity but with a smaller diameter and with minimal spoil. The latter was important in alleviating spoil removal problems near the railway tracks and disposal of potentially contaminated spoil. The results of dynamic compression load testing and static lateral load testing indicated that the performance of a 400 mm V-pile was equivalent to a 500 mm CFA for this site. The lateral load testing indicated that the surficial soils have a major influence on the load-deflection response, but despite the site containing up to 4 m of filled ground, the piles were found to carry the required lateral loads satisfactorily.

Jan 1, 2002

By Jian Liu

The dissolubility of a natural sphalerite (ZnS) in the entire pH range was theoretically calculated, and its practical dissolution in an aqueous solution at different pH values in an inert environment, together with its surface properties after dissolution, was fully investigated. The results of the investigation indicate that the total concentration of Zn (CZnT) decreases significantly with the increase of pH value, while the pH value is set below 8; however, it reverses when the pH value reaches 8. Such a tendency is similar to that of the theoretical calculations, although the experimental CZnT were much higher than those of the theoretical calculations. The X-ray photoelectron spectroscopy (XPS) of the sphalerite surface after its dissolution under alkaline solution shows that a polysulfide (Sn 2-) surface layer with a binding energy (BE) value of 162.96-163.25 eV is present on the surface, and the percentage of Sn 2- increases significantly with an increase in pH value; the undissolved and dissolved sphalerites under the acidic solution have a negligible difference in S2p peaks. The surface S/Zn ratio of all dissolved sphalerites shows a marked Zn enrichment and S deficiency. An atomic force microscope (AFM) view of the sphalerite surface, after its dissolution under the alkaline solution at a pH of 12, shows that the surface is significantly different in morphology from that of the undissolved one.

May 1, 2012

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Sneddon N

In November, 1975, Aberdare North colliery was sealed at the surface to extinguish an open fire underground.The fire had developed from a spontaneous heating in one of the open goaf areas of the mine.The mine was re-entered with normal ventilation methods following the isolation of the working district containing the fire. The isolation was accomplished by remotely sealing the open roadways with lly ash emplaced through boreholes from the surface. A subsequent re-entry operation similarly closed the roadways close to the fire and enabled the re-opening of the sealed district.Most of the mine and the underground equipment was recovered after clearing of numerous falls and production recommenced on 25th October, 1976.

Jan 1, 1978

The drill steel&apos; sharpening shop, which stands adjacent to the Chaffers shaft, is built to the dimensions of 110 ft. 9 in. by 58 ft. wide, and is air conditioned in order to maintain reasonable working conditions during the summer months.Figure 1 is a plan of the shop, showing the disposition of the machines and equipment.LIST OF STEEL SHOP EQUIPMENTAir Conditioning Plant comprising:-1 Spray and Eliminator Type Air Cooler, 6&apos; ft. x 7 ft. x 6 ft. with 80 fine sprays.1 No. 36 Keith type ER. Ball Bearing upcast multivane centrifugal fan.20,000 cfm. a in. WG. at 450 r.p.m.Fan motor, A.G.E. S.C. 10 h.p. 1,160 r.p.m.1 Water Pump. 2?!-3-in. Thompson Class G. Single Stage Centrifugal Pump.1 Pump Motor, A.G.E. S.C. 70 h.p. 1,160 r.p.m.Drill Steel Sharpening Equipment:-2 Holman Sharpening Machines, No. 11.1 Ingersoll Rand Sharpening Machine, No. 54.5 Ingersoll Rand Sharpening Machines, No. 50.2 Holman Hot Millers, Type DM. Double Spindle Machines.2 Morgan Hot Millers, Type 1.6 Reamers consisting of motors with Ingersoll Rand Chuck fitted to the shaft and carrying a reamer of i-in. square Ultra Capital Steel Motors, A.G.E. S.C. 1 h.p. 1,160 r.p.m.4 Double-sided Drill Sharpening Furnaces, oil fired with L.P. &quot;Major&quot; 2-in. non-rotary whirl type burners.Combustion Chamber, 2 ft. 4 in. x 6 in. x 12 in. Oil consumption, 3&#183;3 to 3&#183;8 gallons per hour.Furnace Lining, Standard Kyanite.Firebricks, 9 in. x 3 in. x 4 in.2 Moving Frame type double-sided tip hardening furnaces, oil fired using High Pressure Air reduced to 3 lb. per square inch.Combustion Chamber, 3 ft. 5 in. x 5 in. x 16 in.Burners, &quot;Major&quot; L.P. 2-in. non-rotary whirl type.Oil consumption, 3&#183;3 to 3&apos;8 gallons per hour.Furnace lining-bottom and sides, 60 only 9 in. x 3 in. x 4 in. Kyanite bricks.

Jan 1, 1941

By Wilton Johnson

The Bureau of Mines study indicates that land utilized by the mining industry for mineral extraction and processing from 1930 through 1980 amounted to 5.7 million acres, or 0.25 percent of the land mass in the United States. Land reclaimed by the industry during the same period was 2.7 million acres, or 47 percent of the land utilized. Land use by the mining industry includes surface land used for excavation or mining, for waste from underground mining, and for wastes from milling or processing operations. Data on land use for disposal of overburden waste from surface coal mines and on areas affected by subsidence associated with underground mining are included for the period 1930-71 only. The 10 leading States in total land used for mining over the 51-year period were, in decreasing order, Pennsylvania, Kentucky, Ohio, Illinois, West Virginia, Florida, Indiana, California, Alabama, and Missouri. Seven mineral commodities accounting for 92 percent of land use are, in decreasing order, bituminous coal, sand and gravel, stone, phosphate rock, clay, copper, and iron ore, all predominately surface mined. Bituminous coal production was responsible for nearly half of the total area utilized. Reclamation of mined lands and waste disposal sites over the reporting period was largely on lands utilized in mining bituminous coal; 75 percent of the land used for bituminous coal production was reclaimed.

Jan 1, 1981

By António Fiúza, Anthony Danko, Patrícia Leitão, Aurora Futuro, Cristina Vila, Lurdes Dinis

The average global recovery rates for processing scheelite ores by physical methods are normally in the range 50 to 70%, and it is problematic to attain a minimum grade of 60% WO3 in the concentrates without penalizing further this yield. Direct hydrometallurgical processing of low-grade concentrates or medium- to high-grade ores may become an interesting global economic alternative as it allows increasing the recovery rate, avoiding major penalizations due to the grade of the concentrate and increasing the added value of the final product. Leaching of scheelite by sodium carbonate presents several advantages such as its selectivity regarding the dissolution of troubling metals like iron and aluminium, allowing for a simple and flexible process diagram. However, it has the disadvantage that it is performed at high temperature and pressure with a high consumption of reagents. The feasibility of leaching is appraised by the extraction yield and selectivity, but also by the operating cost. Considering these aspects, a relevant objective of the research was to transform alkaline pressure leaching into a feasible processing alternative directly applicable to both medium- and high-grade ores and simultaneously to low- and high-grade concentrates produced by physical methods. The research used ore samples and low-grade concentrates from a typical skarn orebody as well as high-grade concentrates from a chalcopyrite-scheelite orebody. Different operating conditions were tested. Temperature, pressure and reagent concentration showed to be fundamental, but not exclusive, in determining the leaching behaviour. The operating conditions are milder than the ones generally proposed in the literature or currently in use in industry, but with higher carbonate consumptions. The research was oriented towards potential industrial implementation allowing for the application of optimization methods and straight scale-up to pilot-plan design and project.