Search Documents

By R. Bergstrom

The implementation of a Quality Management System (QMS) or an Environmental Management System (EMS) that conforms to the standards issued by the International Organisation for Standardisation (ISO) no longer needs to result in a bureaucratic nightmare supported by mounds of paperwork. In this sense, this paper describes the Quality Management System that was implemented and demonstrates how the technologies that were developed can be used to satisfy other similar requirements.

Aug 25, 2002

By Joseph Poplawski, Christian O’Keefe, Robert Maron

"Unique and difficult minerals processing measurement situations will be described and the application of passive array-based technology for performing these measurements will be illustrated. Examples of these situations include volume flow measurements in froth lines and flotation feed lines with entrained air, slurry lines with magnetite and other magnetic ore, slurry lines with abrasive or corrosive materials, high pressure lines, and slurry and non-slurry lines exhibiting scale buildup. Other situations include measurement of entrained air levels in pipes and in flotation columns. These measurements are achieved through CiDRA’s patented passive sonar array-based technology. This technology performs two independent measurements – flow rate and entrained air amounts. Two hardware implementations of this technology have resulted in a non-intrusive flow and entrained air meter which easily is installed on the outside of the pipe, and a submersible version for entrained air or gas holdup measurements which is used in flotation processes. Recent developments in extending this technology to solve other unique measurement problems such as valve movement confirmation will be covered.INTRODUCTIONThe minerals processing industry faces many unique and challenging process control conditions and environments. In terms of flow measurements, many of these situations are not being properly served by traditional flowmeters such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. A new class of flowmeters has been developed that solves these unique situations and flow measurement problems. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition. It does so accurately, reliably and without making contact with the fluid. These measurements are performed on practically any type of fluid within virtually any type of pipe.PRINCIPLE OF OPERATIONSonar array-based flowmeters are ideal for tracking and measuring the mean velocities of disturbances traveling in the axial direction of a pipe. These disturbances generally will convect with the flow, propagate in the pipe walls, or propagate in the fluid or slurry. First let us focus on the disturbances that convect with the flow. The disturbances that convect with the flow can be density variations, temperature variations or turbulent eddies. The overwhelming majority of industrial flows will have turbulent eddies convecting with the flow, thus providing an excellent means of measuring the flow rate as described below."

Jan 1, 2008

By L McCracken

Up until 1990 CoalCorp North Island's accident record was six times that considered acceptable in those NSW operations with good accident prevention programmes. This was an obvious avoidable burden on the company in both human and cost terms.   Late in 1989 an accident prevention programme was implemented with the objective of achieving a 50 per cent reduction in the lost time accident frequency rate within 12 months. The key to achieving this objective was recognised as being an attitude change in the total workforce from General Manager downward. Management commitment and action were seen to be critical to the success of the programme.   Through very basic and simple training programmes in accident investigation, analysis and reporting, communication, on-the-job coaching and in focusing on improving supervision skills, the original objective was achieved.   During 1991 the application of methods improvement and hazard recognition techniques are seen as the logical step to achieving a further 50 per cent reduction in the accident frequency rate.

Jan 1, 1991

This paper examines the issues involved in the technical audit and valuation of exploration prospects. Certain methodologies are more appropriate to use depending upon whether the mineral property valuation is of an exploration area, a project under development, or an operating mine. Valuation approaches that are reviewed include the Multiple of Exploration Expenditure, Joint Venture Terms, Rules of Thumb, and particularly the Kilburn Rating Method. The DCF/NPV Financial Simulation Method, even modified by the use of Expected Values, is not considered appropriate for valuing exploration prospects. The choice of the most appropriate methodology and its successful application depends primarily upon the amount of reliable input data available and, more importantly, the experience and judgement of the valuer. It must be remembered that all valuations are time and circumstance specific and will be generally subject to revision as more data becomes available.

Jan 1, 1993

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

By M. Hokkanen, M. Hagfors

The Finnish Defence Forces has destroyed old and spoilt munitions in open surface mass detonations at Hukkakero fell in municipality of Kittilä, Lapland, since 1988. The technique was learned from Sweden. The destruction camp is organized every year at autumn and it lasts 4-5 weeks. During the disposal period one or two charges are exploded per day. The gross weight of a typical charge varies from 150-250 tons including 15-25 tons of explosives. They mainly consist of TNT, but may also contain smaller amounts of amatol and hexotol. As a booster there have been used 2-3 tons of emulsion explosives.

Jan 1, 2015

By B Cope, Y Churi

Roxgold was a small exploration company when it discovered the Zone 55 orebody at the Yaramoko project in Burkina Faso in 2010. Since this time, it has actively progressed the project with the completion of a preliminary economic assessment in 2013, a feasibility study in early 2014 and obtained full permitting for construction in January 2015. With no other underground gold mine in Burkina Faso, developing a modern and productive modern gold mine in West Africa was considered a significant challenge as Roxgold moved from explorer to producer.To facilitate this development, Roxgold engaged an international underground mining contractor to partner this development. This has enabled Roxgold to successfully develop the mine over a relatively short time frame with construction commencing in April 2015, first gold being poured in May 2016 and commercial production being achieved in October 2016.This paper discusses key elements of the project development and highlights some of the challenges faced with operating in a remote poorly developed area with a limited mining culture. Furthermore, the authors highlight the key technical and operational aspects that make the Yaramoko project a very successful development project.CITATION:Cope, B and Churi, Y, 2017. The development of the Yaramoko gold project in Burkina Faso, West Africa, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Xiaowen Liu

The DSC/TG, IR and XRD analysis were used to characterize the heating phase transformation of illite, which came from Ouhai deposit, China. It was discovered that the dehydration and de-hydroxylation of illite carried out stage by stage during heating. The adsorptive water and layer-inter water were dehydrated from room temperature to 500°C; and dehydroxylated in the range 500°C~800°C. In these stages of process, illite?s layer structure kept almost unchanged. After 800°Cillite began to change into disorder structure. At about 1100°C, the layer structure of illite had been destroyed, and amorphous SiO2 and mullite crystallite appeared. At about 1200°C the structure of illite completely destroyed and mullite crystal phase had become perfect..

Jan 1, 2006

By Y. G. Li

The design and construction of the hand-dug caisson pier foundation of the Shenzhen International Trade Centre are described in the paper. In addition discussions and inquires about the load-bearing capacity of the hard bedrock are offered.

Jan 1, 2010

By Dale Matthews

The Getchell Mine, near Winnemucca, NR, was discovered in the 1930s and was initially mined to recover gold from oxide ores. During the 1940s and 1950s, gold was recovered from the highly refractory arsenic sulfide ores using horizontal kilns to roast the ores. During the 1960s, fluid bed roasters were used to oxidize the ore and recover the gold. The mine was shut down from 1968 through 1985. In 1985, heap leaching was started on the low-grade oxide ores that were available. In 1989, a pressure oxidation circuit was started to recover gold from the higher grade sulfide ores. Flowsheet The basic plant flowsheet of the Getchell Mine are shown in Figs. 1 and 2. The plant was designed to process a nominal 2.7 kt/d (3000 stpd) of ore with about an 85% onstream availability and a gold production of 15.5 kg/d (500 oz/ day). Run-of-mine (ROM) ore is fed directly to a wet semiautogenuous grinding (SAG) mill after the +457-µm (+18in.) rock is removed on a stationary grizzly. From the SAG mill, the ore goes to a ball mill where it is ground to 80% -75 µm (-200 mesh) and is then sent to a thickener. The SAG and ball mill operate in closed circuit using cyclones.

Jan 1, 1994

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984

By Ali Porbaha

Rapid growth in the urban development requires continuous search for innovative technologies to construct complex infrastructure systems. Deep mixing is one promising construction technology that has a wide spectrum of applications for development and expansion of complex urban facilities. Large number of reported case history of the projects in Europe, Japan, and the US demonstrate the versatility of the technology compared to conventional methods of ground modification. A large number of factors influence the quality of the soil cement columns; some of these are rooted in the installation process and the effective use of machinery during construction. This paper attempts to present some issues related to installation of deep mixing that affect quality of the treated columns. Presented here are various installation patterns, installation machinery, installation sequence, effect of penetration/withdrawal injection methods, penetration/withdrawal speed, effect of number of shafts, rotation of the blade, shape and orientation of mixing tools, and rotational speed of the shaft on quality of the treated ground.

Jan 1, 2001

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals in the hope of understanding the reasons for poor performance when it occurs, and developing mitigating strategies.This testwork along with a review of the relevant literature has demonstrated that the amount of sulphide added to the primary reactor, relative to the copper concentration, is the most critical parameter dictating plant performance, with pH and residence time important secondary factors. The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. Testwork shows that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. The theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are likely to experience growth in crystal particle size through aggregation rather than heterogeneous nucleation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process.There is evidence to suggest that operating the copper sulphide thickener in the SART Process without flocculants may be beneficial. Thickener underflow densities could improve from the current 10 - 15% range to 40 - 50%. This will not only reduce the flowrate of slurry to the filter, but the filtration properties of the slurry (filtration rate, filter cake moisture content) will also improve. This is one of the most critical engineering and design aspects of the SART Process, and the achievement of high solids density in the thickener underflow will not only improve the health and safety aspects of the operation, but also has the potential to lower capital costs and improve the quality of the final product."

Jan 1, 2016

By I Hustwick

New Zealand Steel Mining Limited operates two independent sand mining operations on the West Coast of the North Island of New Zealand. Waikato North Head 30 km south of Auckland supplies ironsand concentrate as the raw feed for New Zealand Steel's works at Glenbrook and Taharoa 70 km further south, exports ironsand concentrate to Japan.   Taharoa uses two sets of six low pressure Warman centrifugal pumps in series to load bulk ore carriers 3 km off shore through two underwater pipelines. Waikato North Head delivers the ironsand to Glenbrook 18 km through a 200 mm ID buried pipeline using two stages of high pressure positive displacement (HPPD) pumping.   A high level of operating and maintenance expertise has been developed since commissioning the two systems which are proving to be reliable, efficient and of minimal impact environmentally.

Jan 1, 1990

By G. L. Oldright, J. D. Sullivan, W. E. Keck

"An apparatus and procedure developed in the laboratory of the South-west Experiment Station of the Bureau of Mines are capable not only of determining the rate and volume of penetration of solutions into porous materials but also of determining the total volume of voids within particles of porous material, and the density. The method is applicable to ores, bricks, concretes, tiles, filter bottoms, or other porous materials of this nature. As will be made clear in the descriptive matter to follow, the method measures (a) the volume of voids within the porous materials and is not concerned with the interstitial space between the particles.Porous materials usually contain some large voids and also pores that are capillary in nature. To measure the total volume of voids in a sample it is necessary to replace the gas or gases within the voids with some liquid of known density. The large cavities can be filled quite readily, but under ordinary conditions a long time may be required to fill capillary pores. As many porous materials are of a decomposable nature it is necessary to evacuate the porous materials and then submerge them in a liquid of known density to bring about saturation in a short time. Then by the use of a hydrostatic balance the volume of porous material (solid itself) can be determined. To determine the volume of porous material plus voids it is necessary to coat the sample with some material, such s paraffin, which will prevent solution from entering the voids; then, by means of a hydrostatic balance, the volume of porous material plus voids is determined and by subtracting that of the porous material from this the volume of voids is ascertained. The rate of penetration of solutions can be determined either (a) by measuring the change in weight as the sample becomes saturated when immersed ni a liquid of know density, or (b) by measuring the volume of liquid penetrating with a dilatometer. In either instance, due to the fact that some penetration takes place as soon as the sample comes in contact with solution and before a reading can be taken, the sample must be paraffined to determine the total volume of penetration. Since many porous materials partly decompose and disintegrate in liquids the rate and volume of penetration can better be measured by dilatometer than by the change in weight, as saturation takes place when immersed in a liquid. The details of procedure for determining (a) total volume of voids, and (b) rate and volume of penetration are given in this paper."

Oct 1, 1930

By Roy H. Borde

The design of foundations to support overhead signs is primarily based on providing adequate resistance against horizontal wind loads. The typically used subgrade reaction model for the load-deflection analysis of laterally loaded piles and shafts has been found to underpredict the capacity of shafts with length to diameter ratios less than five. The general applicability of an improved model incorporating the influence of shear and moment resistance at the shaft base is demonstrated. The detrimental effect of ground surface slope angle on the ultimate capacity is discussed, and a design chart for estimating the magnitude of the reduction in capacity is presented. A comparison between the predicted and measured responses of nine full-scale load tests performed within this study and sixteen external tests is presented. The models described are implemented in the computer program "LTBASE".

Jan 1, 1988

Increasing depths and mechanization of underground mines have led to the production of large amounts of gaseous and particulate contaminants. Over 100 000 lives have been lost due to methane gas and dust explosions in coal mine workings in both the United States and Canada since 1900. There is, therefore, the need to constantly assess and evaluate the performance of existing mine ventilation systems to maintain safe and acceptable mine environmental conditions. This paper advances research initiatives in the control of methane gas in underground mine environments. It uses the results of continuous monitoring of methane gas concentrations conducted in selected coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems to control methane gas concentrations. The results show that the average quantities of fresh air required to dilute, disperse and remove methane gas concentrations within set levels of one minute varied from 5.43 m3/sec. to 27.97 m3/sec. in the development headings. The average dilution times in the headings studied were less than eight minutes. The calculated dilution efficiencies of the auxiliary ventilation systems in the headings varied from 12% to 139%. These efficiencies ranged from poor to excellent. This implies that the auxiliary ventilation systems were capable of controlling the methane gas concentrations below statutory levels but may not be able to cope with large and unusual methane gas concentrations in the headings. This study is significant in the control of methane gas and coal dust explosions in coal mines.

Sep 1, 2001

By John T. Norton

N order to attempt to arrive at a better under-Jl standing of the whole basic problem of sintering, these remarks will serve as an introduction for discussion that is included and will, perhaps, help to isolate specific questions which need to be answered or to suggest some definite avenues of investigation which should be followed. To bring some sort of logical order into the presentation, I will consider the various types of interaction between the metal to be sintered and the atmosphere which surrounds it, depending upon whether the phenomena are essentially chemical or physical in nature. For example, when the only necessary criterion for the satisfactory sintering of a certain powder is the removal of an oxide skin, then the problem of choosing a suitable atmosphere is primarily chemical; however, if a special surface condition as a consequence of the oxide skin removal is necessary for particularly effective sintering, then the problem becomes a physical one. Of course, the two aspects overlap considerably, but it may be possible to make a distinction in principle if not in practice. The chemical characteristics of the phenomena will be emphasized, since these are the better known. Metal-gas reactions involved in sintering are controlled primarily by the thermodynamics of the processes involved. In which direction will a reaction go and how far before it stops? The answer is to be found in the magnitude of the free energy change associated with the reaction. If a constituent is to be removed from the specimen as completely as possible or if a constituent is to be formed in the specimen as completely as possible, then one chooses conditions which are far from equilibrium so that the reaction is driven toward completion. On the other hand, if the composition is to be maintained at a desired value, then conditions are adjusted as closely as possible to the equilibrium point. This aspect of the problem is susceptible to quite precise analysis, provided, of course, that the significant reactions can be recognized and the required thermodynamic data are available. Conversely, if one asks how fast the reaction goes or how far it proceeds in a given time, the answer is frequently much more difficult to answer in quantitative terms. Yet the rate-con trolling factors of the reactions may be of primary importance in the success of a particular operation, especially where competing processes are at work. Both equilibrium and rate factors must be understood if a clear picture is to be obtained. For instance, in a process for carburizing titanium dioxide, is the difficulty of obtaining a stoichiometric Tic due to a true limitation of the equilibrium or simply to a very slow rate of reaction? An example of this appears in the work of Kalish and Mazza.' They showed that the oxygen content of sintered iron compacts was lower when sintered in pure hydrogen than in the case where the hydrogen was diluted with either argon or nitrogen. The equilibrium oxygen content of the iron would be the same in the two cases, since it is determined by the ratio of the partial pressures of water vapor and hydrogen and this pressure ratio is unchanged by dilution. The rate of oxygen removal, however, under the conditions of a constantly replaced furnace atmosphere, depends upon diffusion and thus upon the concentration of hydrogen in the furnace atmosphere. Possibly the clearest way to illustrate the interplay of these two factors is to consider in more detail some of the typical metal-gas reactions. Adsorbed Gases It is common experience that fine metal powders with their very large surface areas often contain large quantities of gas. This gas, which results from exposure to air or perhaps from some step in the

Jan 1, 1957

By Thomas Schwind, Pamela S. Moran

For short tunnels, a reinforced cast-in-place lining is not economical and shotcreteis a logical substitution. In the past, reinforced shotcrete linings have been constructed with lattice girders and welded wire fabric. For the Russia Wharf Tunnel in Boston, MA, the Contractor, with the help of the Dr. G. Sauer Corporation offered the MBTA a VECP to substitute the reinforced cast-in-place concrete lining with a steel fiber reinforced shotcrete lining. The challenge was to adequately model the ductility of the steel fiber reinforced shotcrete and to test the shotcrete prior to and during construction to assure quality control. To our knowledge, this type of numerical simulation has not been used on any other tunnels in the US.

Jan 1, 2005

horizontal-type classifier prior to charging into a blastfurnace.

Apr 1, 1995