Search Documents

By C. Sun

In this study, numerical simulations of yield pillars employing the finite element method with time-dependent Drucker-Prager material model are conducted. The stress control mechanism of yield pillars on weak floor strata is studied. The development of pillar yield zone, the distribution of pillar stress and the development of failure zone in the weak floor strata are investigated. The study indicates that a properly selected yield pillar size may significantly reduce the peak stress induced in the weak floor strata and effectively control the development of failure zone in the floor.

Jan 1, 1999

By Peter van Dijk, Gary Almeraris, Philip Rice

This paper describes the Contractor’s value engineering design and the construction of the Interstate I-90 highway tunnel sections under the South Station railroad yard in Boston, MA for the Central Artery/Tunnel Project, using tunnel jacking and ground freezing techniques. Three tunnel box sections were constructed and installed, with typical cross-sectional dimensions of 11.6 m x 23.8 m, and respective lengths of 50.9 m, 78.7 m and 115.6 m. A 12-compartment concrete shield was built as part of the front of each multi-sectional tunnel box structure. The jacking systems employed consisted of rear and intermediate jacking stations and up to 87 individual jacks, providing a maximum total thrust capacity of 42,300 t. The tunnel alignments pass through a geologic profile consisting of historic fill, which contains remnants of old waterfront structures, building foundations and a forest of 19th century vintage timber piles, underlain by organic sediments and marine clay. Ground cover over the tunnels is in the range of 1.8–7.6 m. The groundwater table is at depths of 1.5–3 m below surface grade. The paper discusses the techniques developed and equipment used to successfully build and install these tunnel box structures with minimal impact on the commuter and long distance railroad operations directly above the tunnel alignments. Figure 1 shows the track area at the I-90 EB and WB tunnels.

Jan 1, 2001

By E. E. Ungar

Criteria applicable to noise in coal cleaning plants are presented, and the generally applicable noise control principles and approaches are discussed. The operating characteristics and equipment of coal cleaning plants are described. Considerations entering in the selection and design of noise control means are delineated, and specific means for equipment noise reduction are described. The limited utility of acoustically absorptive materials in plant spaces is indicated, administrative means for reducing worker noise exposure are pointed out, and ear-protective devices are described briefly. The reduction of plant noise reaching nearby communities is discussed. Programs leading to quieter machines an coal cleaning plants are suggested.

Jan 1, 1974

By J. A. Kost

A survey of 80 coal producers was conducted to determine the extent and scope of respirable dust control research for underground coal mines and the current methods employed to control respirable dust. Results of the survey showed that proper face ventilation and an adequate water spray system are sufficient to comply with mandatory standards in room and pillar mining. Difficulties still exist with longwall equipment, auger miners and buring machines. In these cases, known dust control techniques are not sufficient to obtain compliance. Present state-of-the-art face ventilation and water systems were discussed in addition to the sampling program.

Jan 1, 1980

By R Ratlou

Increased contamination due to sand in spiral feed has had a negative effect on the efficiency of spiral concentrators at Navigation Plant. The no. 1 seam at Kromdraai opencast, which was previously mined by underground bord and pillar methods, is now susceptible to spontaneous combustion because of air ingress into the old workings which are exposed in the opencast high wall. This posed a risk in the loss of reserves to burnt coal. As solutions, buffer blasting of the preceding cut to collapse bords and soft overburden dressing of un-collapsed bords were implemented to prevent air entering the workings. The latter remedy resulted in increased contamination due to addition of sand in Run of Mine. After evaluating alternatives, a low capital option was selected. The 110t/hr Teetered Bed Separator (TBS) has been installed, primarily to desand and upgrade the feed to the spiral concentrators. The unit indicated an upgrade with a yield increase of 0.4% during test work and is currently showing an overall plant yield increase of 0.97%.

Jan 1, 2006

By A. G. Pasamehmetoglu, N. Bolukbasi, O. Koncagul

A study has been undertaken to establish the relationships between the O&K wedge test cutting resistances and the geotechnical parameters of rock materials in the context of bucket-wheel excavator operation. Prediction equations were formed to estimate the cutting resistance from the geotechnical parameters by multiple regression analysis. The cone indentor index, uniaxial compressive strength and Shore hardness parameters have been found to be the most significant predictors

Sep 1, 1991

By L. W. Saperstein

Public Law (PL) 95-87 contains explicit demands for land use planning in its reclamation and designation sections. Both sections require recognition of local land use plans; however, they are not well integrated. Accommodation to these planning requirements affords an opportunity to create better links among local land use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take a more positive interest in local land use plans and in resource inventories. States should consider handing down to local government the responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 12, 1983

By G. W. Jones

As a part of its general safety program the Bureau of Mines has investigated various means useful for the elimination or mitigation of the explosion hazards in connection with combustible gases incident to the mining industry. Information has been obtained relative to the explosibility of numerous simple and complex gaseous combustible atmospheres. Although experiments along this line have pertained largely to combustible gases in the mining and allied industry, considerable information has been obtained relative to the explosive hazards of combustible gases and vapors used as anesthetics.

Jan 1, 1939

By Luthie Els, Chris Coetzee, Roedolf Koekemoer, Casper Els, Olof Vorster, Frank Fereday

Three electric arc furnaces (EAFs) were constructed by Union Carbide at Tubatse Ferrochrome (TFC) in1975. This plant was expanded to four furnaces at the East Plant in 1985 and the gas cleaning system was enlarged without taking flow dynamics into consideration. In order to improve competitiveness, TFC has increased furnace capacity, partially substituted coal for coke, and changed the charge mix. These changes increase the heat and dust load into the air pollution control (APC) system. TFC embarked on a project to improve the APC capacity by: ?Quantifying the required off-gas capacity ?Optimising the aerodynamic flow through the system by means of Computational Fluid Dynamics (CFD) ?Converting the old Brandt Koyo top entry baghouses to bottom entry ?Upgrading the cleaning system ?Installing Gore-tex® ePTFE membrane filter bags The estimation of required off-gas capacity is traditionally done by rule-of-thumb methods such as specific extraction. A more elegant evaluation method was developed for simulating the effects of changes in charge mix on the furnace reaction gas volume and the APC system. Reaction gases are calculated by modelling the reactions taking place in the furnace and off-gas volumes are compared to both fan and baghouse capacity. This enables identification of bottle-necks in the off-gas system. CFD techniques were utilized to evaluate geometric imbalances and propose solutions to ensure optimal use of off-gas capacity. The system modifications were completed over several months and the modified equipment went into service in May2006.

Jan 1, 2007

By G. C. Smith

Process control applications in the minerals processing industry have grown extensively over the years due to the many benefits derived, both financially and operation-wise. Although control theory is widely known, conventional control does not address many of the problems posed by minerals processing circuits. Some of these problems include interactions between process units, large dead times, few and sometimes unreliable measurements of process variables, non-linear systems, disturbances entering the process, processes with varying dynamics, and many more. For the past 26 years Mintek has been active in the field of providing specific, customized solutions for the minerals processing industry. This paper focuses specifically on applications in milling and flotation control. The underlying control principles have been applied to a wide range of other processes including submerged arc furnaces. Advanced control application is implemented on a common advanced control platform, called the PlantStar. Much innovation has been brought to the fore in terms of adapting theoretical techniques and developing new methods to resolve specific milling and flotation circuit issues by using process control. The general approach adopted by Mintek when implementing advanced control is to enforce stabilization of the process as a solid foundation for optimization strategies to be built upon. In doing this, a robust control solution is presented, and the end result is flow and level stability, better product quality regulation, increase in throughput and a stable feed to downstream processes. The MillStar advanced milling control system ensures that the milling circuit is at all times easy to operate while achieving optimum product quality and throughput. Stabilization should include product size regulation and sump level control. Another important aspect of stabilization control is the handling of milling circuit constraints without introducing cyclical behaviour and with minimal disturbance to the final product quality. Process constraints may include factors such as process water limitations, cyclone feed density, and cyclone underflow angle. An optimization strategy should be developed to increase the mill throughput without affecting product quality or introducing mill overloads. The relationship between solids feed and power draw is examined and manipulated for optimization. The interactive nature of flotation circuits and the presence of recirculating streams tend to make satisfactory control almost impossible with conventional techniques such as PI (Proportional plus Integral) or PID (Proportional, Integral and Derivative) control. The FloatStar Level Stabilizer simultaneously considers all the flotation levels in a circuit by use of a multivariable algorithm, and takes compensating action in anticipation of disturbances. The FloatStar Flow Optimizer is an optimization strategy that controls the concentrate flow rate between various sections of a flotation circuit (e.g. Rougher ?Cleaner; Cleaner ?Recleaner). By controlling the concentrate flow between the sections, the mass pull, circulating loads and residence times of the circuit can be stabilized, thereby enhancing the performance of the flotation process. Optimizing grade and recovery are coupled with the dynamic optimization of circulating flows. The FloatStar Grade-Recovery Optimizer will maximize the grade in a section, whilst ensuring that recovery or any other process specific limits remain within predefined limits. With successful applications on several milling and flotation plants worldwide processing amongst others PGMs, gold, copper and nickel, Mintek has shown that it is a leader in milling and flotation control innovation

Jan 1, 2004

By A. E. Taylor, A. S. Judge, P. T. Lafleche

"Resource development in northern Canada has special requirements which derive from the unique environmental and eco-logical nature of the northern environment. In this paper several case histories in which the Permafrost Research Section of the Geological Survey of Canada (GSC) has participated are used to illustrate how geophysical methods may be used to address some of these considerations. Although some of these examples were developed while examining problems directly related to oil and gas development and transport in frontier regions, such or similar methods also have application to mining problems.IntroductionA critical parameter is the distribution and thickness of permafrost, which in northern Canada varies from being a few metres and discontinuous at the southern limit to thicknesses in excess of 700 m in the Arctic Islands'!'. Figure I is a schematic diagram of typical ground thermal conditions in a permafrost zone. The upper zone is defined by an active layer which undergoes a seasonal freeze/thaw cycle. In the simplest case, the ground remains permanently frozen below the active layer to the depth of the O°C isotherm, which is defined as the base of the permafrost. Water chemistry, pore structure and pore or grain size may cause the base of the frozen ground to be above the permafrost by up to 100 m(2). Ice can be found within the permafrost in the pores of solid rock or sediments, as massive ice within unconsolidated sediments or as ice lenses within fissures in a solid rock mass. The mining technique used in these conditions, whether open pit or underground, can differ considerably from that used in southern Canada. In the high Arctic, for instance, the dry drift method is feasible underground in the permanently frozen host rock. The frozen nature of the wall rocks can obviate water-related problems."

Jan 1, 1987

"To prevent the propagation of mine explosions, the Bureau of Mines recommends:1. That all coal and lignite mines, except anthracite mines shall be rock dusted.2. That rock dust shall be distributed upon top, bottom, and sides of all underground openings of every description, to within. at least 4o feet of all working faces and the areas not rock dusted shall be kept wet.3. That the rock dust shall be maintained in, such quantity that the incombustible material in representative samples of dust collected shall not be less than 65 percent. Where methane gas is present in the ventilating current, the minimum percentage of incombustible matter in the mine dust shall be increased 1 percent for each 0.1 percent of methane.4. That when the rock dust in any area becomes caked so thatit cannot be dispersed readily as a cloud in the air, that part of the mine shall be redusted immediately.5. That the dust to be used shall not contain more than 5 percent of combustible matter nor. more than 25 percent of quartz or free silica; all of the dust shall pass through a sieve having 20 meshes per linear inch and 60 percent or more shall pass through a sieve having 200 meshes per linear inch; the dust shall not absorb moisture from the air to such an extent as to cake and destroy its effectiveness as a dry dust.6. That rock-dust barriers shall not be regarded as a substitute for generalized rock dusting.Research and experience have shown that maintenance of an adequate percentage of rock dust in all underground openings, whether gassy or not, of bituminous and subbituminous coal and lignite mines (anthracite dust does not propagate explosions) is the best means of preventing coal dust explosions. In rare instances where all fine coal particles on the floor, ribs, roof, and timbers are in a muddy condition continuously rock dusting is unnecessary.The term ""underground openings"" refers to all unsealed openings whether they contain track or not, and includes rooms, entries, crosscuts, breakthroughs, rock tunnels, slopes, haulageways, airways, and travelingways. The sealing of unused or abandoned parts of a mine in accordance with Mine Safety Board Decision avoids the necessity of rock-dusting the sealed-off openings.The kind of rock dust to be used should have the approval of the State Mine Inspection Service. Pure limestone or pare dolomite produces the best rock dust, as these dusts have low silica content, little tendency to cake, and a light color that aids illumination. To reduce tendency to cake it is preferable that not more than 75 percent of the dust pass the 200-mesh sieve. All sieve sizes are those of the Tyler screen scale. If the mine personnel is repeatedly exposed to breathing high concentrations of the dust, the percentage of free and combined silica should be as low as possible, preferably less than 5 percent. Persons engaged in the application of rock dust should wear approved dust respirators as listed in Bureau of Mines Information Circular 7030 or revisions thereof."

Mar 1, 1940

By G. W. Jones

As a part of its general safety program the Bureau of Mines has investigated various means useful for the elimination or mitigation of the explosion hazards in connection with combustible gases incident to the mining industry. Information has been obtained relative to the explosibility of numerous simple and complex gaseous combustible atmospheres. Although experiments along this line have pertained largely to combustible gases in the mining and allied industry, considerable information has been obtained relative to the explosive hazards of combustible gases and vapors used as anesthetics.

Jan 1, 1939

By Richard H. Bares

This report describes the purpose and application of seventeen statistical and mathematical procedures used in a series of studies made in the project ?A Systems Approach to the Reclamation of Strip-Mined Areas in North Dakota". The objective is to help readers better understand the utility of these procedures.

Jan 1, 1982

By Roberto J. Guardia, Tim Shell, Robert A. Robinson, Steve Rodolf

Our aging infrastructure includes numerous tunnels that provide easy access through topographic and societal obstacles. These tunnels are renewable resources that require periodic maintenance and rehabilitation to extend their useful lifespan to hundreds or even thousands of years. However, as with any structural rehabilitation project, tunnel liner rehabilitation requires an inordinate amount of evaluation and care due often poorly documented original construction and subsequent repair construction methods and materials. This paper documents the investigation, planning, design, and construction efforts of the rehabilitation of a 74-year old, 216-meter (713 foot) long two-lane highway tunnel in moderately fractured to highly sheared basalt on the Oregon coast. The tunnel consists of four sections lined originally with timber and subsequently overlaid with concrete, and three unlined sections.

Jan 1, 2005

By A R. Cameron

"The number of commercial explosive products available to the mining industry has been steadilyincreasing and associated with this there has been an increase in the range of characteristics or properties of them. This has lead to increased difficulties in selecting the most appropriate explosive for a particular blasting situation. Techniques are available that can be used to evaluate and compare the characteristics of explosives under a range of conditions. Also, the techniques are used to assess the variability in the characteristics between batches."

Jan 1, 1994

By D. R. Flinn

A newly developed chemical conditioning technique, which greatly simplifies the preparation of plating baths for the electrodeposition of titanium diboride (TiB2) coatings, is described in this report. The new plating technique was used to prepare samples of titanium diboride (TiB2) coatings on three types of substrate materials. These samples were then evaluated in both low- and high-speed wear-test programs to determine the wear resistance, microhardness, and adhesion of the coatings. In general, it was found that the wear resistance of the coatings is independent of substrate. Scanning electron micrographs have shown that the coating wear surfaces are very smooth, suggesting slow and continuous removal of the coating during the wear test (that is, adhesive wear). Adhesion between the coating and all substrates was excellent. Microhardness results show that the TiB2 coating is harder than alumina, with a hardness value exceeding 5,000 kg/mm2 measured in one test. The results of the wear tests show that TiB2 coatings have relatively poor wear resistance compared with alumina in low-speed unlubricated sliding environments, but exhibit wear properties comparable with alumina in high-speed unlubricated sliding environments.

Jan 1, 1981

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By R. E. Wilmot

This paper is based on the experiences, over many years, of numerous authors in the South African mining industry and of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and, when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a case where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions in a new mining operation and concludes with two follow-up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2007

By C. S. Samis, D. P. Seraphim

In the presence of oxygen, galena is oxidized in an aqueous medium containing ammonium acetate in accordance with the following reaction: PbS + 1/2 0, + 2 NH~Ac -» PbAc, + So + 2 NH: + H2O. This reaction was studied in an autoclave under oxygen pressure by polarographic measurement of the concentration of lead ion in solution. Oxidation rate is parabolic. The reaction products are lead acetote and elemental sulfur, the latter forming a film on the galena crystal. Reaction kinetics appear to be determined by the diffusion of lead from the galena phase to the solution interface through the film of sulfur. RECENT applications of pressure leaching on a commercial scale have emphasized the metallurgical importance of the oxidation of sulfide minerals in aqueous media by oxygen under pressure. Research experience has shown that sulfates, thio-nates, and metal oxides are the products of humid oxidation of sulfide minerals in basic solutions. The metal oxides may be solubilized in the presence of a complexing ion.' Certain oxide minerals are also amenable to treatment by this type of oxidation.' Several kinetic studies have been made of reactions of this type. Stenhouse' found that pyrite (FeS?) oxidized in a sodium hydroxide solution to produce a soluble sulfate and an insoluble layer of iron oxide and that the kinetics of the reaction were controlled by oxygen diffusion through the oxide layer. Andersen' studied the oxidation of galena (PbS) in a sodium hydroxide solution under oxygen pressure. He found the lead and sulfur to be simultaneously oxidized to produce plum bite ions and sulfate ions, and that the reaction rate was proportional to the surface area of the galena. The kinetics appeared to be determined by the reaction of oxygen and water with the galena surface. In each of the above reactions the metal and sulfur components of the mineral were oxidized simultaneously and at equal rates. In the present study the alkaline medium has been replaced by an approximately neutral solution of ammonium acetate in which lead sulfate is soluble. Under the conditions no sulfate was produced and no sulfur could be detected in the solution. The metal component of the mineral was solubilized and the liberated sulfur remained as a film of elemental sulfur on the surface of the galena crystal. A kinetic study of this reaction was undertaken to establish the kinetic mechanism and to determine the rate controlling step. Specific reaction rates were determined by oxidizing crystals of galena of measured surface areas in an autoclave maintained at the desired temperature and oxygen pressure. The rate of reaction was followed by measuring the concentration of lead in the ammonium acetate solution with a cathode ray polarograph, employing stationary platinum electrodes incorporated in the autoclave. Experimental Materials and Equipment Crystals of galena obtained from Violamac Mines, Retallack, B. C., were selected for oxidation because

Jan 1, 1957