Search Documents

By Mutombo Nombe, Avimanyu Das, Rick Honaker

Enhanced gravity separators (EGS) provide a more efficient separation than froth flotation when cleaning coal in the 150 x 25 µm particle size range. To improve the performance of an EGS unit, air bubbles were injected into the feed stream in an attempt to decrease the apparent density of the coal particles due to the formation of bubble-coal particle agglomerates. Air injection had a significant impact on operating characteristics and separation performance. Coal recovery was increased by 10 to 20 absolute percentage points while a 2 percentage point drop in the minimum product ash content was also achieved.

Jan 1, 2005

The Subtropolis mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, Ohio. In February 2018, mine management began implementing a heading reorientation to better control the negative effects of excessive levels of horizontal stress. The conditions in the headings improved, but as expected, stressrelated damage concentrated within crosscuts. The mine operator has worked to lessen the impact of the instabilities in the outby crosscuts by implementing several engineering controls. With the implementation of each control, conditions were monitored and analyzed using observational and measurement techniques including three-dimensional (3-D) LiDAR surveys.

Jan 7, 2020

By J. F. Barkley

Under the procedure of the American Standards Association, with the American Society for Testing Materials as sponsor, the Sectional Committee on Classification of Coals has arrived at the classification of coals by rank as shown in Table 14/. The standard explains the term "agglomerating" used for classification under physical properties, as follows: Agglomerating Index. - Coals which in the volatile-matter determination produce either an agglomerate button that will support a 500-g weight without pulverizing, or a button showing swelling or cell structure, shall be considered agglomerating from the standpoint of classification.***. Pending the adoption of a method by the American Society for Testing Materials, the coke-button grading test5,/ afforded by the examination of the residue in the platinum crucible incident to the volatile matter determination, shall be used.

Jan 1, 1937

By C. D. K. Gauert

High-pressure waterjet technology is proposed as an alternative tool for selective underground mining of high-grade ore sections in stratiform orebodies showing a preferred ?bottom? or ?top? enrichment such as the Witwatersrand reefs and the Bushveld Complex platiniferous reefs. This technique, utilizing known mining technology together with more advanced machinery and additives as used in industrial and cleaning applications, may lead to an increased life-of-mine (LOM) for mining operations. A series of experiments was successfully carried out in a laboratory on Witwatersrand quartzite material, indicating acceptable cutting performance. Mining volumes by selectively cutting of reef portions are considered to be comparable to traditional drilling and blasting. Economic advantages of waterjet mining include energy savings due to the lower quantity of gangue rock to be hoisted to surface, as well as savings by a decrease in the usage of blasting materials. Capital expenditure of waterjet cutting, if applied on a broad scale, could be lower in the long term than that of conventional drilling and blasting methods. Mining by the application of high-pressure waterjet technology could become a competitive ?green technology? improving the economics and safety of labour-intensive mining operations. This paper suggests that waterjet cutting at an industrial scale can become a routine hard-rock mining technique in the future. Keywords waterjet cutting, high pressure, mechanized narrow reef mining, abrasive agents, costs, selective mining.

Jan 1, 2013

By P Blattner

The Late Miocene gold-silver bearing epithermal system at Waihi has some close similarities in its paleo-thermal and geochemical structure with modern, volcanic-hosted geothermal systems such as Ohaaki-Broadlands. At Waihi an extensive braided quartz vein system is enveloped by hydrothermally altered andesites with minor tuff breccias and tuffs. A main stage of vein filling consists of multiple phases of chalcedonic quartz and fine to medium grained quartz, which are accompanied by pyrite, sphalerite, galena, chalcopyrite and acanthite below the base of oxidation. Platy calcite is present locally. Fluid inclusion studies indicate that the main stage quartz was deposited at temperatures of 189¦-273¦C from dilute (Tm of -0.1 to -1.0¦C) fluids that were locally boiling. Homogenisation temperature Th versus Tm data points lie within the field enveloped by dilution and boiling/gas loss paths determined for the Ohaaki geothermal field, and indicates that the parent hydrothermal fluid for the Waihi epithermal system had a similar composition to that at Ohaaki, ie 0.2 wt% equiv NaCl and 3.3 wt% equiv CO2. The hydrothermal alteration mineralogy and the isotopic composition of vein calcite indicate that the hydrothermal fluid contained relatively high concentrations of CO2 , as at Ohaaki. Oxygen isotope analyses of main stage quartz range from 6.1 to 11.6 %0 and of vein calcite from 2.29 to 9.4%0. Calculated d18Owater values for the hydrothermal fluid that deposited the main stage quartz range from 2.0 to -5.7%0, with a trend to less negative values with depth. They are similar to those in the deep chloride fluid in active geothermal systems with a substantial fluid throughput. A high fluid throughput at Waihi system is also evident from the extensive high intensity hydrothermal alteration and large volume of quartz deposited in the vein system.

Jan 1, 1995

By Paul C. McWilliams

The U.S. Bureau of Mines has, primarily through its contract program, used large-scale centrifuges to determine design criteria for tailing embankments. The centrifuge runs were made at two installations, the University of Cambridge, Cambridge, England and Sandia National Laboratories, Albuquerque, NM. The major problems considered were as follows: slope stability of embankments, modeling erosion and seepage, use of the phreatic surface level to ascertain the validity of centrifuge modeling, and the effects of compaction and weathering on a tailings embankment. This report summarizes the results of the four test series conducted at University of Cambridge and Sandia National Laboratories. A review of prior centrifuge applications to mining problems is included. Consideration is given to future centrifuge application to mining problems in both soil and rock mechanics.

Jan 1, 1989

By H G. Bosmare, G Bedser, C V. B Cunningham

Peak Quany has achieved substantial improvements to its bottom lie by giving close attention to blasting practice, and in pr@icnlar by introducing electronic delay detonators for routine production blasting. The precision and flexibility provided by these units has enabled the quarry to gain control over fmes and curtail oversize without increasing explosive usage. In addition, the extent of nuisance from blasting vibrations has been reduced.

Jan 1, 1998

By Jiulong Cheng

Underground coal mining causes overburden deformation and failure, one major form of which is bed separation in the overburden. Surface subsidence can be controlled by injecting grout into the bed separations. For a long time, the grouting results of bed separation can not be validated. This is the problem in the application of this technique. This paper analyzes the conditions leading to bed separation, develops mathematical models for seismic wave fields generated before and after bed separation, and bed separations grouted with different materials, and computes the seismic wave field characteristics using the finite difference method. The results show that the existence of bed separation causes changes in the characteristics of seismic wave field, and that different grouting materials generate different seismic wave field characteristics. Intact strata, bed separation, and bed separation filled with air or water all display distinctive seismic wave field in amplitude and frequency spectra. After mining, the original location that provides strong seismic reflection wave no long exists. It is replaced by a weak and syncline-shaped reflection wave. The area, where the seam wave disappears, is larger than that of the mined area. The location, where a bed separation occurs, generates a set of reflection waves stronger than the normal one. The energy of the reflection waves varies with the materials filling the separations. Bed separations filled with air generate stronger reflection waves than those filled with water. The major frequencies for those filled with air are lower than those filled with water. Therefore, it is possible to determine the property of filling materials by analyzing and comparing the amplitude and frequency spectra of the reflection waves. Case studies of application of seismic method for exploring bed separations and grouting were analyzed. The results show that it is feasible to use seismic technique for exploring bed separations and grouting.

Jan 1, 2006

By Mohan K. Wali

This report, the first in a series of 13 reports, provides a summary of 11 major topics on which individual reports have been prepared. These major topics are: (a) Nature of coal mine spoils, topsoils, and unmined soils; (b) influence of macro- and microclimate on (c) plant production on spoils and topsoils; (d) prediction of aboveground biomass from plant cover; (c) mineral composition of plants; (f) controlled environment studies on plant growth response; (g) microbial communities (h) water chemistry and organism diversity of catchbasins; (i) vegetation and soil development on abandoned, and (j) topsoiled sites; and (k) viability and diversity of seed bank. Based on these investigations, general conclusions and some recommendations are presented.

Jan 1, 1982

By K. Kawakami

In Japan, pile foundations have been used extensively for buildings, bridges and port facilities. A large number of steel pipe piles were first used in the 1960's and the amount of steel used in foundations increased by 1973 to one million tons. This report describes current practice in the actual use of large diameter and long steel pipe piles in Japan, related to their performance: including consideration of pile size, hammer types used for driving the results of field tests measuring stress occurring in the piles and the driving formulae currently being used in practice in Japan.

Jan 1, 2010

By James J. Neate

The augered cast-in-place pile system came into use in the late 1940's where various techniques were tried using pressure grouting methods. In the early development stages some piles were installed using the preplaced aggregate concrete system. As development continued it became more apparent that placement of coarse aggregate was more costly than making a pile out of a cement and sand mixture only. Various techniques were tried consisting of pumping structural grout into an open hole through a pipe left in the bottom of the hole, drilling or driving a pipe in close proximity to the tip elevation of the auger or in working a pipe down adjacent to the auger fluting. For these techniques the pipe was usually withdrawn after grout appeared at the surface. In 1951 a patent was applied for by Raymond Patterson describing the above techniques along with a technique for placement of grout using a hollow stem auger and a removable plug or lead bit at the tip of the auger. The plug or lead bit was removed by grout pressure and this would be an expendable item for each pile placed. The patent was granted in 1956 and patent rights were assigned to Intrusion-Prepakt, Inc. Shortly thereafter other contractors were granted licenses to utilize the system. Patent coverage expired in 1973 and this method now is in the public domain. Today the method is in wide use throughout the world and is particularly well accepted in Japan and England.

Jan 1, 1988

By J. Roth

The purpose of the present study is to increase the safety of explosive storage. This was accomplished by: a) review of the histories of recent and past magazine explosions to define causes and trends; b) observation of present-day explosive storage conditions and practices at active mines; c) examination of existing Federal regulations on explosive storage to determine whether they address all conceivable safety problems, whether they contain redundant or obsolete standards, and whether their intent is clearly stated; d) recommendation, for safety improvements and for revision and clarification (if necessity) of governmental regulations. Magazine explosions are rare. A recent increase in magazine explosion frequency must be attributed to a large increase in deliberate (criminal or malicious mischief) explosions. Fires of various origins account for the remaining explosions of the past decade. During 1884-1926 several lightning-generated explosions occurred in non-metal magazines, but none recently. It appears that the contents of a well-constructed, metal magazine are immune to direct lightning strikes, regardless of whether the magazine is grounded or not grounded. Grounding a metal magazine cannot be harmful, but it may well be superfluous. Magazines were observed at 34 widely separated mines and storage problems were discussed with personnel at these mines. In general, storage conditions and practices were found to be satisfactory. Usually, only small quantities of explosives are stored on mine property since most explosives are brought in by suppliers when needed. MSHA and BATF standards on explosive storage appear to cover safety aspects adequately. However, certain revisions are recommended to clarify some of these standards and to reduce inconsistencies in their enforcement.

Jan 1, 1983

By Kevin Andrews, Terry Hamric, Scott Nelson

"Mining conditions in underground coal mines are dictated by the environment in which the coal seams were geologically deposited. Depositional features can change rapidly, significantly affecting mining conditions. Mine geologists understand factors affecting mining conditions, predict future conditions, and provide guidance to mine management. A case study demonstrates how a mine in Appalachia merged an understanding of depositional environments with mining conditions and drilling data to make informed decisions as the mine encountered geologic anomalies. The assessment included drilling, mapping of geologic hazards and mine productivity, and creation of a conceptual depositional model. Metallurgical coal quality and clean tons per foot served as incentives for continued advance. Mining in the south was historically favorable, with good production and advance rates. As mining advanced north, changing geologic conditions caused the upper seam split to abruptly disappear. The mine ramped down into the lower seam split. Mining in the north area encountered unfavorable conditions, including transition roof, “horsebacks,” sandstone intrusions, roof rolls, and bony floor, resulting in low rates of mining advance. The mine geologist characterized the features and created a predictive model for future mining. Most of the adverse conditions were attributed to the coal in the north being part of an incised, transgressive valley fill environment, as compared to the favorable conditions in the south resulting from a floodplain depositional environment. Geologic conditions, low productivity, and unfavorable future predicted conditions in the north ultimately resulted in mine closure and reallocation of resources to a new mine with better forecasted conditions.INTRODUCTIONThe role of a geologist in assisting coal mining operations to understand and predict the impact of varying geological factors on mining productivity is a critical one, especially when management decisions must be made about the future prospects of a mine operating in difficult conditions. Chase, Newman, and Rusnak (2006) provide a very thorough discussion of the evolution of the role of the coal mine geologist and emphasizes the importance of understanding geology with regard to mine management decisions. Using actual mining performance data to determine which geologic factors are the most critical for mining is a powerful tool for making informed mine management decisions. For example, Nelson, Mullennex, and Miller (1988) provide a case study of analyzing the geologic factors impacting productivity of a Kentucky longwall mine to predict future mining conditions for the operation. In that case, the difficult geologic factors for longwall mining were prevalent across much of the remaining permit area and, in response, mine management converted the operation from a longwall operation to a continuous miner (CM) operation to better adapt to the geology. In another example, Keim and Miller (1999) evaluated geologic conditions impacting a West Virginia longwall mine. In both examples, significant geotechnical and geological information was available, including the opportunity to compare predicted mining conditions against actual conditions as mining progressed. Numerous examples of advanced Geologic Hazard Mapping (GHM) methodologies have come from government agencies and academia. For example, development of the Coal Mine Roof Rating (CMRR) system (Molinda and Mark, 1994) provided a standard means for geologists and engineers to communicate quantitatively with regard to mine roof conditions, and the introduction of the Stability Mapping System (SMS) provided an efficient means for analyzing numerous factors affecting coal mine stability (Wang and Heasley, 2005)."

Jan 1, 2019

James Barnes is Managing Director of James Barnes & Associated Ltd which is a company that has invested ten years of development to provide developers with a transparent, user friendly consultation framework that identifies who needs to be consulted, how they are to be consulted and procedures required to manage the risks associated with getting all the wrong! Despite the assertion above, this paper is not about to provide delegates with the answer to whom they ought to consult or identify the expectations that Maori might have in regard to the consultation process. It would be a very brave person indeed who would venture an opinion on such a sensitive subject. There are no short cuts to finding out what expectations Maori might have on any given situation. Nothing can be taken for granted. What this paper will attempt to do however is provide practical insights into what might be on the minds of Maori interests as they deal with the issues associated with mineral resources, particularly those under Treaty of Waitangi Claim. The Treaty of Waitangi has a significant bearing on the current debate between Maori and the Crown regarding ownership of mineral resources in New Zealand. The Waitangi Tribunal is currently hearing a case presented by a number of Iwi over the ownership of oil and gas resources in Taranaki and Hawkes Bay. Others will follow. The Crown and Maori have never been able to settle differences over ownership rights without resorting to legal action and it looks like this scenario is about to be repeated in regards to minerals. The Crown has a duty to actively protect the Maori interest. This is a fundamental expectation in the relationship between Maori and the Crown. In the case of minerals, Maori have yet to see the Crown do its duty. The impact on developers has become evident through Maori objections to consent applications as the issues of mineral right remain unresolved.

Jan 1, 2000

Geostatistical methods have become well established in the last two decades for the evaluation of ore reserves in base metal, industrial minerals, coal and gold deposits of the Witwatersrand type. However, there has been considerable debate about the applicability of geostatistical techniques when applied to vein-type gold deposits with hydro or epithermal mineralisation. The main problems stem from a lack of spatial continuity and the highly erratic sample values that characterise these deposits. This paper reviews some of the current geostatistical techniques that are applied to the evaluation of gold prospects.

Jan 1, 1992

New Zealand has been a significant producer of gold for over a century. Total recorded production is over 850 tonnes. There were three major periods of production: the first and biggest was between 1860 and 1880, the second was between 1895 and 1920 and the third was between 1930 and 1945. After 1945 gold production fell continually until 1980 when the major upward adjustment in gold price led to renewed interest. There have been important new developments in each of the known gold-rich areas: Westland, Otago and Coromandel and exploration for gold in these areas and in previously unprospected regions has reached unprecedented levels.

Jan 1, 1988

By E. C. Hoeman, W. C. Stoecker, R. C. Redfield

"INTRODUCTION Industrial sands, characterized by specific physical and chemical proportion, are,essential new materials for the manufacture of glass, sodium siliante and other products. Sands of suitable characteristics are used extensively for molds and cores in the casting of metals as a granular medium in municipal water filters, as abrasives, as traction sand to prevent the slipping of driving wheels of self-propelled vehicles on trucks and in various ceramic and other structural forms. In addition to the use of common silicon sands in concrete, cement, and mortar, special sands find use in sand-lime brick oxychloride cement, and flooring, for coating prepared roofing, and for placing ware in saggers although sand for sandpaper has been mostly displaced by other harder mineral or synthetic grains, other abrasive uses are numerous and include sandblasting stone sawing, glass burnishing and finishing."

Oct 1, 1945

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li2O-A1203-4Si02) a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Rills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade e deposits it s in North Carolina. The theoretical lithia (Li20) content of spodumene is 8.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By Gábor Csicsovszki

We have developed a novel method - at the laboratory scale - comprising an ion-exchange separation and a membrane-electrolysis step for the purpose of zero-waste regeneration of spent HCl pickling liquors originating from hot-dip galvanizing of common steels. It is aimed at the parallel regeneration of HCl and iron. Experiments revealed that iron can be electrodeposited at high current efficiencies by maintaining the following conditions: 0.04-0.08 M HCl, 500-1000 A/m2, 20°C and stationary electrolyte in a conventional cell. Zinc in the solution did not disturb the deposition of iron, however it contaminated the product and it poisons the anion-exchange membrane required to tackle acidity during electrolysis. For a preliminary separation, anion-exchange tests were carried out to produce pure iron solutions. Beyond the equilibrium studies, column experiments were carried out showing that low flow rates of the loading solution and the ~1.5 M HCl eluent are essential for separation.

Jan 1, 2006