Search Documents

A pyrite flotation concentrate assaying 0·065 oz/ton gold was investigated to determine the mode of occurrence of the gold. Ftom cyanidation and acid leaching experiments it was concluded that O· 02-0· 03 oz/ton goldwas in solid solution in pyrite and the balance of the gold was finely dispersed as grains throughout the pyrite.Autoradiography and electron-probe examination of possible areas in briquetted concentrate did not detect any grains of gold. Neutron irradiation and gamma spectrometry confirmed on 100 mg samples the fire assays obtained on 1 assay ton samples.Oxidation to hematite and reduction to magnetite at 600°C made practically the whole of the gold extractable by cyanide. This technique could be of major significance for gold ores which contain a substantial amount of "refractory" gold.

Jan 1, 1969

By K. A. Grace

K.A. Grace's article advocates usage of the terms describing resources as defined by the US Bureau of Mines (USBM) and the US Geological Survey (USGS). Originally recommended in 1943, the terms were revised in 1976 and again in 1980. Mr. Grace further recommends that the term reserves should be severely restricted and that it should encompass mining and processing factors. The list of references quoted in the article does not, however, mention the study concerning reserves that was made over a period of almost four years by a joint Committee on Definitions. This committee was sponsored by three societies - the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the Society of Economic Geologists (SEG), and the American Institute of Professional Geologists (AIPG). Most of the detailed work was done by a working party appointed by the Society of Mining Engineers (SME) of AIME. After studying previous definitions in the US as well as in the United Kingdom, Canada, Australia, France, and other European countries, the following definitions were proposed and accepted in 1974 by the SME board of directors. (Ore reserve definitions in Rhodesia, South Africa, or New Zealand were not mentioned as having been reviewed.) Table 1 lists definitions from MINING ENGINEERING, July 1975. Notice in Table 1 it was mentioned, under Resources, that the definitions of reserves were recommended for the purposes of commercial evaluation. It was further stated that the terminology adopted by the USBM and the USGS, as released to the public, covering resources, was recognized as such. Mr. Grace also recommends that reserve calculations should allow for future losses in ore tonnage, ore grade, milling, and smelting. Unfortunately, it might take years to develop a prospect after it has been discovered. Mining methods have to be tested before being finalized in order to know what tonnage of ore is going to be lost, or how much dilution is likely to occur. The same problems are present in concentrating or in smelting. Operating mines usually know how mined grade compares with ore reserve grade. They can usually predict fairly closely what their final metal recoveries are probably going to be. It is, however, expecting too much to have to delay quoting reserves from say a recently drilled prospect. Any responsible mining geologist or mining engineer (or company for that matter) should state several things about an ore reserve calculation: that it is or is not a preliminary estimate only; that estimated grades have not been diluted to allow for a future, as yet unknown, mining method; that metal recoveries are or are not only tentative, based perhaps on drill hole samples only or on no metallurgical testing at all. Reserves of a partially explored prospect are always quoted when it becomes necessary to raise capital. If they are described as preliminary only (really just tonnage and grade estimates and not true "reserves") in addition to being accompanied by some of the items just mentioned, nobody is going to be misled. If, on the other hand, a report by a member of the SME or SEG is intentionally misleading, the individual must be reported and eventually disbarred from his or her society. To summarize, let us stay with the definitions of ore, ore reserves, and related terms as recommended and accepted by SME. I might add that on occasion I have used a fourth category in my ore reserve calculations, namely Geologically Possible Ore. This category is more or less the same as Inferred ore defined by the USBM and USGS. I have never given a grade to this category, which may be based only on geological mapping, geochemical sampling, or geophysical traversing.

Jan 8, 1985

THE Talisman mine is situated on the Waitawheta (pronounced Wytaffetta) river just above its junction with the Chinemuri (pronounced Chinnemurre) river near Karangahake, NZ. The explored reef-bearing portion of the claim includes the angleformed by the junction of the rivers and extends southwards for slightly over a mile (See Plate V.). The country is mountainous both rivers flowing through precipitous gorges.The trig. station on Karangahake mountain is almost directly above the workings on the Bonanza section and is 1680 ft. above river level, the adit from the gorge giving 1200 ft. of backs measured vertically. The officers of the N.Z. Geological Survey are engaged in a detailed survey of the Waihi district and the rocks of Karangahake are under examination. The rocks of the district are andesites and dacites much altered and silicified. One of these exhibits a columnar structure in the mass in the Waitawheta gorge near the surface workings on Taukani hill, also on the southern bank...

Jan 1, 1912

By J Law, S Jahanshahi, R Holmes

Iron ore is AustraliaÆs largest commodity export and is vitally important to AustraliaÆs current and future prosperity. However, while major expansions are currently in progress to satisfy demand, the industry is also undergoing major transformations. Reserves of traditional high-grade Brockman ores that have underpinned the Australian iron ore industry since its inception are slowly being depleted and alternative ore types such as Marra Mamba bedded iron deposits, Yandi and Pannawonica channel iron deposits and magnetite deposits are now being developed. However, the impurity levels in some of these alternative ores are higher and they require blending and/or upgrading as well as an advanced knowledge of their downstream processing characteristics to facilitate cost-effective utilisation by overseas customers. The research challenge is to use advanced techniques for mineral exploration, ore characterisation, mineral beneficiation, agglomeration and sustainable processing to identify and develop innovative and breakthrough options for locating, unlocking and enhancing the value of AustraliaÆs iron ore resources. Furthermore, to sustain the steel industry and hence secure the demand for iron ore, there is a growing need to enhance the environmental and business performance of the industry through reductions in wastes and emissions. Therefore, cost-effective breakthrough and enabling technologies that massively cut waste generation, CO2 emissions and water consumption are also being developed. These include the use of renewable fuels and reductants, waste heat recovery and conversion of by-product slag into a saleable substitute for Portland cement. A number of examples of recent developments in the above areas are provided in this paper.CITATION:Holmes, R, Jahanshahi, S and Law, J, 2013. Research and innovation for the iron ore to carbon steel value chain, in Proceedings Iron Ore 2013 , pp 3-6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Tracy Brettmann

The use of rock-socketed Augered Cast-In-Place (ACIP) piles is new to the Austin and central Texas region. This case history describes the design methodology, load test results, quality control procedures and the rate of production pile installation for the first large commercial project where ACIP piles were used in Austin. The piles were 24 inches in diameter and extended through about 45 ft of alluvial materials to be socketed 6 ft into limestone. A full-scale instrumented load test was performed on a test pile that was loaded to 452 tons and held for 24 hours. Telltales were installed in the middle and the tip of the test pile. As part of the overall quality control procedures, singlehole sonic integrity logging was performed on the production piles to verify structural integrity during pile installation. During pile production, an average of 14 piles per day were installed, which is approximately seven times faster than the original design that consisted of drilled shaft foundations.

Jan 1, 1998

The process of electrostatic separation was developed in the late 19th century, but did not make much headway for about 25 years. High dc voltages, of the order of 20 kilovolts, are involved, and the only means of obtaining such voltages at that time were by the use of frictional machines, such as the Wimshurst. These were not reliable, for two reasons:-a. If a spark discharge occurred it took an appreciable time before a steady voltage was again attained.b. In damp weather the machines were almost useless.In the first 20 years of the 20th century the advent of mechanical and vacuum-tube rectifiers led to promising developments of 'the process. In the early 1920's flotation became widely used commercially, and proved to be more reliable, and capable of wider application, than electrostatic separation. During the last 15 years or so, with a better knowledge of the fundamentals forming the basis of the process, electrostatic separation is beginning to compete with flotation, especially in the treatment of smallsizedgranular material, such as beach sands. Electrostatic separation can be, and is, widely used in many cases where flotation is impossible, such as in the cleaning of food products which must be kept dry.

Jan 1, 1950

By C. Deutsch

Resource estimation for the West Leeville deposit is prepared using a conventional explicit approach. The geologic model is developed using interpretive methods based on visual logging. Grade shells are then prepared at low and high grade cutoffs. The low grade shell includes material of interest (Au > 0.010opt), while the high grade shell is developed slightly below the economic cutoff grade for mining. Grade estimates are made within these boundaries. This paper documents a conditional simulation study to evaluate the uncertainty contributed by both the grade shells and grade estimates. Multiple realizations are generated for the grade shells and the grades. The full combinatorial of realizations are merged to assess the uncertainty and the relative contribution of the grade shell and grades.

Jan 1, 2007

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

Water Balancing in Mineral Processing - Issues and Opportunities

Sep 13, 2010

By C. Ogasawara

This document describes the direction and progress of the Bureau of Mines Oil Shale Mining Environmental Research Program as of January 31, 1979. It is aimed at focusing the Bureau's role in environmental research supporting oil shale development with respect to the activities of other involved government agencies and private industry. Environmental considerations in oil shale extraction, such as ecological disturbances, health and safety hazards, waste management, and socioeconomic impacts, are discussed along with the type of research known to be planned by organizations to ameliorate these problems.

Jan 1, 1979

By Monique Pharand, Jeet Basi, Simon Hille

"High quality activated carbon is essential in the recovery of gold in Carbon-in-Leach (CIL), Carbon-in-Pulp (CIP), and Carbon-in-Column (CIC) circuits. Goldcorp’s Campbell complex at Red Lake Gold Mines (RLGM) experienced a period of low soluble gold (Au) recoveries during Q3 2013, during which time the processing plant saw higher than typical Au grades in the CIP tails solution stream. A technical review identified that the CIP circuit may be experiencing a carbon-fouling issue. To further understand the degree of fouling, and to troubleshoot the low recovery problem, samples of carbon were collected from the CIP, elution, acid wash, and regeneration circuits, and submitted for characterization test work. This paper summarizes the steps taken to remedy the carbon-fouling problem at RLGM resulting in increased overall Au recovery.Overview of Red Lake Gold MinesRed Lake Gold Mines is located approximately 450 kilometres northeast of Winnipeg, Manitoba, in Ontario’s western boundary region.All mining is carried out through underground operations, utilizing overhand cut and fill, underhand cut and fill, and long-hole mining methods. Ore types include: silica-replaced carbonate veins with free milling gold, siliceous replacement-type mineralization (rich with arsenopyrite) marginal to veins, broad disseminated sulphide mineralization along major shears, and some minor sulphidized chemical sediment-hosted ore. The operation is supported by two milling complexes: Red Lake, and Campbell.Process DescriptionThe Campbell processing plant's main unit operations consist of grinding, gravity concentrating, flotation, autoclaving, leaching, carbon-in-pulp (CIP), carbon elution and reactivation, electro-winning, bullion smelting/refining and cyanide destruction, and concentrate handling. A schematic of the plant flowsheet is shown in the figure below.BackgroundHigh quality activated carbon is essential in the recovery of gold at many CIP/CIL/CIC processing plants. At RLGM, gold-bearing ore is milled and cyanide is added to leach the gold from the solids into solution. The dissolved gold then comes into contact with activated carbon, and adsorbs onto its highly porous surfaces. Gold is then recovered by separating the activated carbon from the main slurry for further refining. As such, the characteristics and quality of the activated carbon have a significant and direct impact on overall gold recovery."

Jan 1, 2016

By David J. Blackwell

The challenge; to design production facilities and in particular separation equipment which have the ability to deal effectively with the ever changing composition of well fluids, over the life time of the field in which it is operating, ensuring maximum uptime of the asset coupled with consistently effective separation. Design engineers are, however, continually confronted with a dilemma when selecting materials of construction for Oil/Gas separation equipment, since they are generally obliged to select an acceptable material of construction, based on ?predicted? operating conditions, at the lowest acceptable cost. Consequently many designs are somewhat basic and do not take into account the constantly varying dynamics of the well fluids being released into the separator. As oil fields mature, oil companies endeavour to maximize revenue by maintaining oil and gas throughputs. This often results in an associated increase in water and sand volumes and, in order to maintain efficient separation, an increase in operational temperature and pressure; subjecting the equipment to operational conditions for which it was never designed. In reality, therefore, the limitations and constraints placed upon new construction design often result in Maintenance Engineers having to solve the ensuing problems in difficult ?in-field? environments. Should refurbishment or upgrade be required then the status of the platform and that of the vessel during shutdown will dictate how this is achieved. Hotwork on the vessel is generally not preferred due to the requirement for post weld heat treatment and re-classification of the pressure vessel, not to mention the added risk in terms of safety. Unfortunately, until recently, there have been few alternatives to conventional ?hotwork? repair and protection systems, especially since the performance of cold curing polymer based repair and coating systems, for use in oil and gas process equipment, has, until recently, been limited by their resistance to temperature and pressure in immersed conditions. In line with the continued development of high temperature / high pressure oil and gas fields however, recent breakthroughs in polymer technology can now offer both repair and protection solutions which are able to function effectively at temperatures up to 180°C in immersed conditions combined with resistance to the destructive forces of explosive decompression from pressures in excess of 90 bar. This paper will look at recent work that has been undertaken to determine the suitability of modern polymer based repair and protection systems as an alternative to hotwork; thus enabling newly designed and upgraded internals to be cold bonded into position and further protected with temperature resistant coatings, in order to minimize the downtime of the asset and further to protect the vessel internals from the Erosive Corrosive environment.

Jan 1, 2006

Characteristics Analysis of a Bastnaesite Rare Earth Mineral for Recovery of Cerium

Sep 13, 2010

By Lancucki C. J, Nickson N. M

X-ray diffraction and differential thermal methods were used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis was made of the mineralogy and particle size distribution of eighteen samples from beds in two pits in the Recent sediments in the Adelaide plains, of six white clays developed from the weathering of the Adelaide series of sediments, and of four Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products in the Adelaide area are manufactured from mixtures of these clays, so the mineralogy and particle size distribution was determined of eighteen clay mixtures used to make red bricks, cream bricks, facing bricks, pipes and tiles.Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.INTRODUCTIONIn this investigation an account is given of the clay mineralogy and particle size distribution of some ceramic clays from the Adelaide area. The clays are used in the manufacture of structura,l clay products and the results to 'be described are part of an overall 'plan of study covering the heavy industrial clays and shales of Australia. Previous work has been published (Cole and Carthew, 1953; Ferguson, 1954; Ferguson and Hosking, 1955; Cole and Nielsen, 1958/59).In this work no attempt has been made to examine clays from all pits engaged in supplying materials for the structural clay industry. However, in 1954 the senior author collected detailed samples from two pits working in Recent alluvial clays in the Allenby·Gardens and Beverley areas near...

Jan 1, 1963

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010

This Bureau of Mines publication consists of an overview of the mine waste management research currently being conducted by the Bureau. The following papers, given at a Technology Transfer Workshop, emphasize the increasing importance of research related to the safety and environmental considerations of mine waste disposal In recent years. Current work related to legislation passed in the last 10 years and their subsequent standards includes the development of adequate monitoring systems, development of stability and seepage prediction and control techniques, control of runoff water, and control of leaching solutions. Selected topics are included here that cover coal mine waste disposal, embankment slope stability monitoring, flow failures of mine tailings impoundments, and controlled burnout of abandoned coal mine fires. The projects described provide a current documentation of problems being addressed.

Jan 1, 1981

By Donald Leroux, Simon Gariépy, Luc Lachance

"Quantitative information about the quality of metal balance results is often overlooked when making important plant production planning decisions. Not only is this common omission made in a context where many measurements taken in and around mineral processing plants carry significant errors, but it also conflicts with the AMIRA P754 Code of Practice for Metal Accounting. The fact that metal balances are typically published without any indication of data quality may give the wrong impression that the measurements are unquestionably accurate. While it is true that statistical data reconciliation can improve the confidence intervals of redundant variables, there is no data processing technique that brings them down to zero at a finite cost. In this paper, we review the entire data flow, starting from field instruments to metal accounting-based decision-making to show how measurement errors are transmuted into business risks associated with production planning. Necessary conditions for first exposing then quantifying such business risks are stated. Pitfalls to be avoided are also discussed. Finally, a simplified risk assessment and management procedure which considers the quality of metal balance results are applied to a polymetallic mineral processing plant. INTRODUCTION Each and every mineral processing plant has production reporting obligations. In this paper, we are concerned with metal accounting reports (Morrison, 2008) where saleable metal flows and inventories are estimated and published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimisation, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that spotless metal accounting is instrumental to high-quality corporate governance (Gaylard et al., 2014) of mining and metallurgical companies. To this extent, one would have expected industry-endorsed standards to have emerged a long time ago. However, the lack of an accepted set of standard procedures for metallurgical accounting was explicitly recognized as an industry-wide problem only in August 2001 during an SAIMM workshop held in Cape Town, South Africa. Discussions that followed this workshop led to the initiation of the AMIRA Project P754, “Metal Accounting and Reconciliation”, in 2003."

Jan 1, 2015

By D Lichti

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995