Search Documents

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

In the process of oxygen blast furnace, the lower coke ratio and the higher coke load make the skeleton coke more important. To understand the dissolution of coke in melting and dropping zone, the influence of FeO content, temperature and reaction time on the dissolution of coke with slag were studied by single-factor experiment. Meanwhile, the three factors and three levels orthogonal were conducted. The dissolution degrees were characterized by the weight loss ratio and diameter variation. The results showed that the weight loss ratio increased and the diameter decreased with the increase of FeO content, temperature and time. The three factors and three levels orthogonal test showed that time was the most significant factor on coke dissolution, FeO content of the second, and finally the temperature. The microstructure of coke after reaction indicated that the dissolution occurred on coke surface.

Jan 1, 2016

By Mary Cunningham

The EPA and DOE have collaborated on a series of studies to evaluate the effectiveness of treatment technologies at stabilizing bulk elemental mercury and wastes containing high concentrations (i.e., with greater than 260 mglkg total mercury) and multiple forms of mercury. The data from these treatment demonstrations are intended to help EPA to determine if regulatory revisions to allow a stabilization alternative for high-mercury subcategory wastes are warranted. In addition to mercury-contaminated wastes, the disposal of bulk elemental mercury is of concern because of the excess quantity of mercury in the Defense Logistics Agency (DLA) stockpile, as well as other potential sources of excess elemental mercury. The studies evaluated the effectiveness of several technologies at: I) stabilization of mercury in a "hard-to-treat" matrix; and 2) conversion of elemental mercury into a stable waste form for disposal. A surrogate waste was designed for the study on high-mercury wastes, which included an organic form of mercury, elemental mercury, and several mercury salts in an inorganic matrix. The surrogate waste and the bulk elemental mercury were treated by the vendors, and the treated waste forms evaluated for mercury Icachability, using both the TCLP and an automated, constant-pH leaching protocol. Constant pH leaching was conducted at pH 2,4,6,8 10 and 12 for 14 days at each pH. The leaching data demonstrate that the stability of the mercury in three treated waste forms varies widely across the pH range tested. Clearly, the stability of mercury in these treated waste forms will be highly dependant on the disposal conditions. The combination of site-specific disposal conditions and appropriate treatment technology must be considered as decisions are made about disposal of high-mercury wastes.

Jan 1, 2003

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By Jana Dobrovska

Solidification and cooling of a continuously cast slab and simultaneous heating of a mould is a very complicated problem of transient heat and mass transfer. Nowadays, the solving of such a problem is impossible without numerical models of the temperature field not only of the slab itself, while it is being processed through the whole concasting machine (Caster), but of the mould as well. Two original numerical models have been developed and used in the investigation of a continuously cast steel slab. The first (one of two) 3D model of the temperature field of a concasting is capable of simulating the temperature field of a caster. Experimental research and data acquisition have to be conducted simultaneously with the numerical computation-not only to confront it with the actual numerical model, but also to make it more accurate throughout the process. After computation, it is possible to obtain the temperatures al each node of the network, and at each time of the process. The utilization of the numerical model of solidification and cooling of a concasting plays an indispensable role in practice. The potential change of technology-on the basis of computation-is constantly guided by the effort to optimize, i.e. to maximize the quality of the process. The user can therefore choose any appropriate longitudinal or cross-section of a slab and display or print the temperature field in a 3D or 20 graph whenever necessary. The second numerical model of dendritic segregation of elements assesses critical points of slabs from the viewpoint of their increased susceptibility to crack and fissure. In order to apply this model, it is necessary to analyze the heterogeneity of samples of the constituent elements (Mn, Si and others) and impurities (P, S and others) in characteristic places of the solidifying slab. The numerical model, based on measurement results obtained by an electron micro-probe, generates distribution curves showing the dendritic segregation of the analyzed element, together with the distribution coefficients of the elements between the liquid and solid states. The combination of both models enables the prediction of cracks and fissures in critical points of the continuously cast carbon-steel slab. Both models had been applied in the industrial investigation of a cast low-carbon-steel slab.

Jan 1, 2003

By Zeng Zheng, Liu Chen, Yu Xing-Fu, Tian Su-Gui, Zhang Chao

"Single crystal nickel-base superalloy is prepared by using the various withdrawing rates. By measuring creep properties and microstructure observation, the influence of the element segregation on creep properties of the superalloys is investigated. Results show that the dendrite spacing and the segregation extent of the elements decrease with the enhancing withdrawing rate. The superalloy with smaller dendrite spacing has lower segregation of the elements and better creep resistance. The dislocations climbing over the rafted y’ phase is thought to be the deformation mechanism of the alloy during steady state creep. In the later stage of creep, the fact that some dislocations shear into the rafted y’ phase may twist the rafted y’ phase. As the creep goes on, the initiation and propagation of the cracks occur up to occurring creep fracture, which is thought to be the fracture mechanism of the superalloy during creep.1. IntroductionSingle crystal nickel-based superalloys consist of high volume fraction of ?? strengthening phase and ? matrix, and possess the excellent high-temperature mechanical and creep properties, therefore, they have become the main material to make the blades of the advanced aeroengines[1-3]. Some literatures report that the temperature-bearing and creep-resistance properties of the single crystal nickel-based superalloys can be remarkably improved as the increases content of the refractory elements, such as W and Re[4-6]."

Jan 1, 2012

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015

By R. G. Reddy

Viscosities of alkaline metal oxide-silicate melts were estimated using our previously developed mathematical model. The structural based model considers depolymerization effects and related breakdown of the silicate network structure, on the addition of metal oxides to the melt. The developed expression: n =4.9x10 9 NO 0 T ½ exp(E/RT) poise was used to calculate the viscosities of various binary silicate systems such as, CaO-SiO,, MgO-SiO, and MnO-SiO,, as a function of temperature and composition. Excellent agreement was obtained between the calculated and experimentally determined viscosities.

Jan 1, 1991

By E. F. Vegman, Ndabezinhle Dube

"In the practice of conventional sintering, production is always afflicted with the problem of being unable to get a uniform quality of produced sinter in the bed. Invariably the top layer of the sinter cake is composed of weak but highly sinter, while the bottom layer is over-fused, forming a sinter that is very strong but less reducible. These symptoms point to a variable distribution of the heat balance in the process of sintering which results in a deficit of heat in the top layers of the sinter bed and an excess of heat in the bottom layers, due to an increasing input of regenerated heat in the heat balance down the bed. This causes losses in the productivities of the sinter machine and the blast furnace.The current work was designed to improve on the solution to the above problem through the establishment of a more accurate combustion zone heat balance of the sintering process. This development is mostly on the method of determining the regenerated heat input in the overall heat balance. Previous methods were based on the assumption that the width and the velocity of the combustion zone remain constant through out its whole life, which is not the case since tests have shown that both its width and velocity increase as the combustion zone moves down the bed. In this work, these factors have been taken into account. Tests and calculations using the model were carried out for haematite and limonitic ores. The high sensitivity of the model to changes in the sinter mix composition and sintering conditions was demonstrated.The results present the following prospects:• The minimum theoretically possible coke breeze consumption during the sintering of any type of iron ore fines, under any sintering conditions, can be established.• The model can be used to control the metallurgical quality of the sinter in any point in the sinter bed since calculation data includes desired basicity, combustion zone temperature and FeO content in the sinter produced."

Jan 1, 2001

By Tuula Mäkinen

One of the latest applications of the Outokumpu Flash Smelting Technology is the direct smelting ,of nickel concentrates to metallised low-iron nickel mattes. Compared to the conventional nickel smelting, the new DON process needs a lower number of smelting vessels resulting in considerable economic and environmental benefits. Fundamentals of smelting nickel concentrates in one stage to low-iron mattes are presented. Properties of nickel. smelting slags with an emphasis of the slag fluidity at high MgO-levels are also discussed. Conditions prevailing in DON mattes at high oxidation degrees are presented as well as their influence on the behaviour of such mattes in the settler and on tapping the furnace. Distributions of elements in the direct smelting are presented and compared with the conventional process. A further comparison is made with pilot-plant data and the industrial scale.

Jan 1, 1998

By William Petruk

The concentrator of the Iron Ore Company of Canada consists of spiral circuits, a cone plant and a magnetics plant with regrind. The proportions of liberated and unliberated grains of iron oxides at each point throughout the concentrator were measured by image analysis, and recoveries were calculated for each particle type by the MATBAL materials balancing program. The results show that spirals and cones recover more than 92% of the liberated iron oxide grains in the size range of 848 to 150 um,, but the recovery drops off rapidly for finer grained particles. The tailings from the spirals and cones are reground and low intensity magnetic separators are used to recover liberated magnetite in the -37.5 um size range. The concentrator does not have a unit that efficiently recovers iron oxide grains in the size range of 150 to 37.5 um Consequently about 25% of the iron oxides in the ore are lost to tailings as liberated. grains in the size range of 150 to 37.5 um

Jan 1, 1989

By Pekka Taskinen

The converter-less nickel matte smelting technology (DON) adopted more than 20 years ago in Boliden Harjavalta smelter has been since that applied successfully to the processing of large number of nickel sulphide concentrates of various Ni-to-Cu ratios and MgO contents. The operational point of the technology is far from the conventional primary nickel smelting in the smelting-converting route. Therefore, a careful scouting of distribution equilibria of the base and trace elements in the smelting conditions of DON process has been conducted, in order to obtain quantitative information about the equilibria and thermodynamic properties of the nickel mattes at low iron concentrations, less than 10 wt% [Fe] in matte. The series of investigations has included novel experimental and analytical techniques for increasing the reliability and sensitivity of the phase equilibria as well as the element distribution observations carried out in typical high-grade nickel matte smelting conditions.

By Cong Wang, Siyang Long, Pengcheng Zhang, Haibin Zuo

This paper introduced the research progress of microwave treatment on coal. The mechanics of microwave treatment mainly include thermal effects and non-thermal effects. Thermal effects, which lead to cracks and changes of pore structure, attribute to the selective heating of microwave. Non-thermal effects involve the removal of oxygen functional groups, improvement of coal rank and decomposition of minerals. Therefore, microwave treatment of coal has a lot of potential applications, mainly including drying, desulfurization, improvement of grindability, enhancement of coal-water slurry property and change the combustion and gasification properties.

Jan 1, 2016

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By Tao Xuea

Gold frequently occurs in nature in the form of a gold-silver alloy. Thus, investigation of the electrochemical behavior of gold-silver alloys in cyanide solution has practical significance. In this paper, the potentiodynamic method is used to determine the anodic polarization curves of gold-silver alloys (Au-10% Ag and Au-50% Ag) in cyanide solutions. To facilitate the interpretation of the results, complementary experiments conducted in NaOH solution in the absence of cyanide are also reported. The results for the Au-Ag alloys are compared with the polarization behavior of pure gold and pure silver. With the aid of potential-pH diagrams for the Au- and Ag-CN-H20 systems and electrochemical kinetics concepts, the dissolution mechanism of gold-silver alloys, the effect of the presence of silver on the cyanidation of gold, as well as the factors which control the anodic reaction rate are clarified.

Jan 1, 1998

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By S. Ajima

The Naoshima Smelter and Refinery is the most important copper operation of Mitsubishi Materials Corporation. There are a Mitsubishi Continuous smelter and a conventional type of copper tankhouse. The continuous smelter with 240,000 mtpy of anode production was commissioned in May 19914 replacing two existing smelters, i.e an original Mitsubishi Process line and a conventional reverberatory furnace line. In July 1992, the copper tankhouae was expanded for the purpose to close the gap of production capacity between the smelter and the tankhouse. The cathode production capacity was increased from 13,800 to 15,800 mtpm. By these plant modifications, the distribution of minor elements was significantly changed and the impurities load is getting on increase reflecting recent shortage of clean copper concentrates supply. The paper discusses the distribution of minor elements and the impurity control strategy at the smelter end the refinery.

Jan 1, 1995

By Gabriel Riveros

The stags from the Teniente Converter (TC) have high copper and magnetite contents. The reduction and copper impoverishment of these slags in an electric furnace was simulated in the laboratory, as part of a conceptual study for the Ventanas smelter of ENAMI. The effect of power input, electrode immersion, temperature of the slag, coke and solid revert additions on the rate of magnetite reduction and copper recovery was investigated. It was found that the addition of solid reverts, containing copper matte, enhanced the recovery of copper. Magnetite stratification and a corresponding gradient of the copper content occurred in the slag. Microscopic examination of slag samples showed the presence of copper in the form of matte and metallic copper inclusions. The results of the experimental work combined with an analysis of the phenomena that take place in an electric furnace led to a better understanding of the slag cleaning mechanism. The successful start-up of the slag cleaning electric furnace at the Ventanas smelter resulted in good copper recovery and confirmed the beneficial effect of solid reverts addition. Electrode consumption is lower than anticipated. No bottom build-up problems have been experienced. Keywords: copper, slag, magnetite.

Jan 1, 2001

By José D. T. Capocchi

Viscosity of liquid lead, tin, and Pb-Sn alloys has been measured by the rotational viscometer method in the temperature range from 50 K above their respective liquidus temperature to 823 K. The results are accurate to within ±1.0 %. The variation of viscosity with temperature followed the Arrhenius-type equation µ = µo.exp(Q/RT). The composition dependence of the isothermal viscosity and the activation energy for viscous flow have not shown anomalous changes at the eutectic composition of the Pb-Sn system.

Jan 1, 2000

By Ali Nadir Khan

Depleting copper resources and advancing technologies have challenged industries to develop more viable, adaptable and cost efficient processes using also secondary raw materials in copper production. This study is targeting to that goal by dynamic modelling of flow and heat transfer coupled with chemical kinetics in an industrial scale flash smelting furnace settler using commercial CFD software ANSYS Fluent. First, different physical phenomena occurring inside the settler, for example, settling and separation of the matte/slag phases, and heat transfer between slag/matte phases and settler walls are studied. Secondly, reaction kinetics between matte and slag, and between slag/matte and settler walls, and impurity element distribution will be studied. This would also include phase changes phenomena due to these reactions and the flow of the reaction gases inside the settler. Settling of polydispersed droplets, their coagulation, breakage, and WEEE particle behavior are further targets of the modelling work.

By T. Fujita

The removal of phosphorus is essential 1n order to increase the recycling of steelmaking slags for their manganese, iron and lime contents. This study aims at establishing the phosphorus mineralogy and its distribution in steelmaking slags, the effect of slow cooling, and the methods of phosphorus removal. A series of steelmaking slag samples was prepared at different cooling rates, and the mineralogy, chemistry and grain size of the samples were investigated with SEM/EDS and x-ray diffraction. The test results using high gradient magnetic separation are discussed.

Jan 1, 1988