Search Documents

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By A. H. Kaksonen

Numerous reactor designs for biological sulfate reduction have been reported. Fluidized-bed bioreactors (FBR) can efficiently retain biomass and allow high mass transfer and reaction rates. This work reviews the development of various sulfate-reducing FBR processes for treating acidic metal- and sulfate-containing waters and recovering metals from bioleaching liquors. The FBR process performance was evaluated with continuous flow experiments under various operational conditions: fluidization rates, influent pH values, metal, sulfate and salt concentrations, hydraulic retention times, electron and carbon sources, and temperatures. Substrate utilization and sulfide inhibition kinetics were determined with batch FBR-kinetic experiments. An artificial neural network (ANN) model was used to predict the performance of the FBR. Sulfate-reducing bacteria (SRB) were characterized in FBRs with molecular and culture-based approaches with the aim to gain a better understating of the bioprocesses. Based on the studies, FBRs are well suited for the combined removal of metals, acidity and sulfate from water.

Jan 1, 2010

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By F. D. Ayhan

The aim of this study was to investigate desulfurization and de-ashing of a mixture of subbituminous coal and gangue minerals by the agglomeration method. For this purpose, experimental studies were conducted on a mixture containing subbituminous coal, pyrite, quartz and calcite. The effects of some parameters that markedly influence the effectiveness of selective oil agglomeration, such as solid concentration, pH, bridging liquid type and concentration, and depressant type and amount, were investigated. Agglomeration results showed that the usage of various depressants (Na2SiO3, FeCI3, corn starch, wheat starch) in the agglomeration medium has a positive effect on the reduction of ash and total sulfur content of agglomerates. It was found that an agglomerate product containing 3.03% total sulfur and 25.01% ash with a total sulfur reduction of 56.71% was obtained from a feed that contained 7% total sulfur and 43.58% ash when FeCI3 was used in the agglomeration medium. Key words: Desulfurization, De-ashing, Agglomeration, Coal, Gangue minerals

Jan 1, 2009

By William R. Hess

Volcanic ash, although a little-used Kansas resource, is available in forty counties with estimated, reserves of more than 20 million tons. It was first produced in Kansas in the early 1900?s but not until the early 1920 is did it become an important abrasive material. Total production to date is estimated at 2 million tons, the major use being as an abrasive in scouring compounds and soaps, additional uses include ceramic glazes, an additive in cement, and a filler and stabilizer in hot mix asphalt for paving. Unrecorded tonnages have also been used in construction of black-top (macadam) roads. From 1916 through 1944, Kansas ranked first among the states in volcanic ash production; peak production was about 52, 000 tons in 1923. Since 1945, production has steadily declined, primarily because materials other than volcanic ash are now being used for abrasives; only two producers operated in 1964.

Jan 1, 1965

By H. Reed

The precious metal mining industry in Nevada handles and generates a certain amount of hazardous materials and waste on a regular basis. These products range from processing material additives to wastes from laboratory testing, heap leaching, and hydrocarbon treatment and disposal. The volume of materials and wastes is dependent upon the amount of ore processed. Handling, treatment and disposal is dependent on the type of material handled and the waste generated. Owing to the health and safety concerns and due to the existing regulations that control handling and disposal of hazardous materials and wastes, the mining industry is obligated to comply with all applicable requirements for proper handling of these products. Plus, in an effort to minimize any impacts from this effort, the industry is continually looking for alternative methods to accomplish these requirements and to also minimize costs. This paper will discuss the general, and in some cases the specific conditions, by which the industry is coping with the issue and efforts to minimize any impacts from handling, treatment and disposal for hazardous materials and wastes. The subject of compliance with the Toxic Release Inventory (TRI) requirements and bio-treatment of wastes and other technologies will be discussed.

Jan 1, 2001

By M. J. Zdunczyk

Located approximately 50 miles northeast of Knoxville, Tennessee, Short Mountain Silica mines the Clinch Formation, an orthoquarzite, for silica sand. In 1980, a Knoxville resident and area contractor visualized mining Short Mountain for silica sand. Because APG Industries, the main market for the glass sand product, was only 48 kilometers from the site, many silica sand companies became interested in the property. In 1986, J.D. Nicewonder began to develop the site, and in May of 1988, APG Industries received the first sand shipment.

Jan 1, 1992

By G. Newman, C. D. Sellars, E. A. Portfors

Power for mine operation in remote locations is usually provided by diesel generators. For gold mines where processing is normally desirable on-site, power requirements can be significant and the operating cost for diesel generation then becomes an important factor in mine feasibility. If a suitable site is available, a small hydroelectric power facility near the minesite can provide a significant portion of the mine power requirements. The hydrological, engineering and economic factors involved in small hydroelectric power development are described in this paper. Capital costs are minimized by run-of-river hydro development which does not require a dam and reservoir and has less environmental impact. During periods of low flow, diesel generators are used to make up the power demand. The hydrologic analysis required to determine unit energy costs is described and technical requirements for linking the hydroelectric power facility with diesel generation are outlined. Case studies are presented demonstrating the economic advantages of a small hydro installation. One case study is for a proposed gold mine in British Columbia and the second is a large operating gold mine overseas, for which the hydroelectric power scheme is presently under construction .

Jan 1, 1987

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By Laszlo Valentyik

Heavy media separation (HMS) is one of the most widely used gravity methods in the mineral industry. The feed is separated, according to the specific gravities, into two products; float (light) and sink (heavy) particles. The universal acceptance of the process is due to simplicity, efficiency and robustness for ease of control. However, if optimum separation is desired during the operation of heavy media plants, a delicate balance of a number of variables is essential. Among the variables, the two which are generally the most frequently checked and controlled are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media. The medium is generally made up of finely ground ferrosilicon, magnetite, galena, shale, quartz sand, clay contaminants and water. The frequently present clay in the medium acts as a stabilizing agent, since the coarse heavy medium solids (called media) would quickly settle if they were mixed only in water. Clay concentration of the medium varies between 3-7% by height (1,2). Although clay is essential for reasonable media stability, clay concentration greater than 7-8% imparts too high a viscosity to the medium, and the feed cannot accurately stratify and therefore separate into the required products. To be on the safe side, plant operators clean the medium from most of the clays, and would rather work at a lower stability than have a very viscous medium on their hands. The most recent advance in the area of consistency control rlas made by the introduction of atomized (spherical) ferrosilicon (3). This extended the upper limit of the use of ground ferrosilicon from 3.3 to approximately 3.6, broadening the range of the optimum operating conditions. A viscosity control method was also worked out by the use of low cost additives which lower viscosity while retaining a favorable low setting rate (4). Recently (5) polymers have been successfully used in oil well drilling muds then the requirements were mainly to suspend and transport cuttings during the periodic shutdowns and dril1ings respectively. The rheological properties of these polymer suspensions are such that they present an infinite viscosity to

Jan 1, 1971

By I. S. Parrish

As noted by McKinstry (1948), "How to deal with erratic high samples is one of the knottiest problems in ore estimation." He described a variety of approaches and methods to alleviate the problem through the averaging and weighing of assay data and by "cutting" or "clipping" of the erratic assays. Bird (1991) elaborated on ways of dealing with the nugget effect (erratics). He listed several procedures for cutting. Bird's list has been reproduced and/or added to by several authors including Vallee (1992) and Stone and Dunn (1993). Missing from each of these otherwise excellent reviews is a definition, description or guideline to recognition of an "erratic," or just where or when cutting is warranted or justified.

Jan 1, 1997

By T. H. Combs

Increased productivity in the U.S. underground coal industry has taxed pre-existing conveyor belt haulage systems. The usual remedies are costly and can disrupt production. A reduction in the belt feeder discharge rate on mobile haulage sections results in more uniform loading and reduces the spillage vulnerability. An investigation is made to determine the effect, if any, on shuttle car discharge time arising from lower feeder discharge rates. A five-section, underground mine is visualized, and belt spillage is introduced. The sectional feeder discharge rate is progressively lowered until spillage is precluded. At each level, the simulated spillage is measured and compared to the loss in face production. Methods of predicting the loss in face production from lower feeder discharge rates are discussed.

Jan 1, 1993

By J. B. Knaebel

I have been asked to discuss the "Development of the Twin Buttes Mine for Production." This property, which is a large low-grade open pit copper mine about 25 miles south of Tucson, Arizona, was recently brought into production by The Anaconda Company under a long-term lease agreement with the Banner Mining Company. Since the scope of this paper is limited to the subject broadly indicated by its title I will confine discussion of historical, environmental and other general matters to a brief summary sufficient, I hope, to establish a background of those conditions which influenced our approach to the technical and economic problems that faced us at Twin Buttes. The paper deals primarily with our studies and activities related to the solution of these problems and with the resulting engineering and business decisions that were taken - decisions which culminated last September in the initial commercial operation of another major open pit copper producer unique and interesting in several respects.

Jan 1, 1970

By R. Mishra

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solutions. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors will demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning.

Jan 1, 1977

By Carl E. Williams

During the past two years a computer program called "COPOR," Computerized Open Pit Optimization Routine, has been developed and used for mine planning of several base metal deposits. This routine utilizes a three dimensional computerized block model of an orebody, some economic parameters and operating constraints to locate the mineable or economic limits of the deposit schedule the yearly production from the mine and produce bench by bench ore reserve summaries and maps of the yearly and ultimate pit configurations. The moving cone method is used to perform these functions with a conventional block model. This model is conventional in the sense that each block is assumed to be homogenous; i.e., either ore or waste but not a mixture of the two. Due to the nature of a seam type deposit this approach is not realistic; therefore, revisions have been made to form a new version of the COPOR program. This version has been named "COALOR," Coal Optimization Routine. COALOR contains all of the power of the COPOR program but is equipped to handle the intricacies of coal seam type deposits. The deposit can be composed of a single seam or multiple seams which are horizontal or dipping at any angle. The numerous coal quality values can be incorporated to aid the optimization of the economic pit limits and yearly scheduling.

Jan 1, 1978

By L. Adler

The valuable Maximum Utilization Factor (MUF) concept has been extended to other rotating excavators beyond stripping shovels and draglines. In this concept the boom reach and bucket capacity are multiplied to get an MUF, then normalized by dividing by the equipment weight. Statistical analyses were applied to the remaining shovels (hydraulic and cable), draglines, and backhoes. Positive correlations were found. Stripping shovels and draglines were also re-examined. The results provide an estimate of equipment diggability and encourage versatility by the interchange of the boom and the bucket. The concept further clarifies the existing equipment classification by delineating general excavating, loading, and stripping kinds. The results also forecast trends, and noted innovative advances and possible retrogression. Extension to other boom excavators, such as front-end loaders is recommended. The MUF concept provides one of the few indices of gross external characteristics available to the engineer-user of equipment.

Jan 1, 1990

By B. E. Davis

A technique was devised by the Bureau of Nines to recover coarse (plus 1.7 m) North Carolina phosphate now discarded as waste. Concentration utilizes the difference in particle sphericity between the relatively flat calcite and the rounded phosphate pebbles. Sizing, treatment in a continuous hydraulic classification system, and grinding upgraded a 17.0-pct-P205 reject to 24.5 pct P205 with a phosphate recovery of 63 pct.

Jan 1, 1985

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By James J. Snodgrass, David E. Siskind

The Bureau of Mines investigated the effects of vibrations from underground blasting in four rock types to define blast parameters that affect vibration amplitudes and to establish means of predicting expected vibration levels. Previous studies of surface blasting indicated that charge weight per delay period had a major influence on vibration amplitudes. Dividing the distance from the blast by the square root of the charge weight scaled the effect of various charge weights, however, and allowed vibration data for a particular site to be represented by a propagation equation of the form v = K(D/W ½ )-n (1) where v = particle velocity, D = distance from the blast, W = maximum charge weight per delay period, and K and n = empirically determined site constants. For square-root scaling, particle velocity and acceleration data from the underground sites appear to follow a similar propagation law. The subsurface data are in good agreement with those of the surface studies and provide a basis for engineering estimates of vibration amplitudes in many different rock types.

Jan 1, 1974