Search Documents

By Joseph L. Condon

The U.S. Department of the Interior, Bureau of Mines, is doing research on methods to obtain premining information on problems such as detection of old mine workings, abandoned oil wells, channel sands, faults, and other geologic features that are undesirable from a production or safety aspect. Techniques being developed to acquire the necessary information include seismic and electromagnetic. The seismic methods include high-resolution seismic and acoustic methods applied from the surface and inseam channel waves applied under- ground. The electromagnetic, or radar, methods are applied from the surface, from boreholes, and from the working face underground. All of these methods are useful under certain site-specific conditions, but none of these methods is universally applicable for all mining conditions.

Jan 1, 1980

By James E. Monsees, Wayne A. Carbiener, Michael R. Wigley

This paper illustrates an approach to quantitatively document the degree of technical conservatism to be incorporated into the design of a waste isolation system in bedded salt. It is anticipated that for an actual repository site the key performance constraints and/or design bases identified in this paper will be reviewed, and modified or supplemented as required. Ultimate acceptance of a repository will be dependent upon scientific peer input and scrutiny of the demonstrated conservatism inherent in each specific repository site and design.

Jan 1, 1981

By Claus Becker

At the RETC 1979 in Atlanta/Georgia it was reported about the beginnings of the Hydroshield system and the first site experiences. Since that time over 10 miles of tunnels in various diameters have been built with that system, and the discussion of the two most interesting projects will be the main topics of this paper. AURELIA TUNNEL, ROME In Rome, the railway system is going to be completed and modernized. Therefore, it is necessary to tunnel through the Roman hills. Part of the new railway system is the Aurelia Tunnel, located some 100 feet below the famous Via Aurelia Antigua, close to the Vatican. The double track railway tunnel has an internal diameter of 9.44 m and a length of 2.410 m. It runs through completely differing soil conditions. (Fig. 1) The first 1000 t are situated in watertight clay, the rear part in water bearing loamy, clayey sands with interlayers of loamy clays. The figure shows the soft change-over from clay to sand. The groundwater head is between [ ]

Jan 1, 1983

By John M. Marek, David E. Nicholas

INTRODUCTION The purpose of this article is to outline the data requirements for selecting a proper underground mining method and to discuss the general steps taken in selecting that method. Determining the appropriate mining method is an iterative process that continues throughout the life of a mineral deposit. We will discuss the subject from the standpoint of a feasibility study, where a realistic assessment is necessary in order to determine investment merit. The feasibility stage of a project is that point where the drilling program has defined sufficient geologic reserves to consider mining the deposit but little or no underground development has been done. Primary parameters for consideration in choosing a mining method are 1) geometry of the deposit; 2) distribution of grade; 3) rock mass strength for the deposit, as well as the hanging wall and footwall; 4) mining cost and capitalization requirements; 5) mining rate; 6) type and availability of labor; 7) environmental considerations; and 8) other site-specific conditions. Of these parameters, the first four have the most impact on determining the general mining method to be employed.

Jan 1, 1981

By S. F. Willey

The difficulties encountered in justifying replacements for over-age mobile mine equipment at the Gay Mine are common to most mining operations. More critical management reviews, resulting from ever rising capital expenses, increased such difficulties. These increased difficulties are especially apparent to those who are primarily operators and are not statisticians, mathematicians, or computer oriented. The Gay Mine is located 17 miles east of the town of Fort Hall in southern Idaho. This open pit operation annually supplies the J. R. Simplot Company and the FMC Corporation with 1.5 MM - 2.0 MM tons of phosphate ore. Stripping ratios average approximately three bank cubic yards of waste per ton of ore mined. The mobile mine equipment fleet consists of ten 24 yard scrapers; twenty-one 30-50 ton end dump trucks; four 32 42 yard shovels; fifteen dozers in the D-8 and D-9 classes; and three road patrols. Equipment replacement is based on the results of evaluations made on individual units. Authorization of capital expenditures for equipment replacement is dependent upon a favorable profitability index (true rate of return on investment) plus a favorable payout time. The system is based on cash flows and requires the determination of (1) the net cash outflows in the form of capital expenses plus (2) the expected cash inflows resulting from reduced expenses and depreciation tax credits. After adjustments for taxes and the time value of money, the net amounts are used to calculate the required indices. The basic elements for the system related to the replacement of mobile mine equipment include: (1) the determination of dollar penalties to be expected from the continued use of aging equipment; (2) the selection of equipment that will provide the greatest return on the investment dollars; (3) the quantification of the expected savings; and (4) the calculations of the prescribed indices. Inadequacies inherent in previous evaluating methods led to the search for more

Jan 1, 1972

By Gary Brieley

Until well into the 20th century, most construction work was performed under the auspices of a master builder or in a manner that would be described today as design-build. In addition, many civil engineers served as ?interns? under the tutelage of a master builder in order to learn how to design and construct a certain type of structure. This was certainly the case for tunneling projects with various individuals having been identified as tunneling experts as a result of successfully completed projects The master builder approach began to change in the early 1900s to a model that would be referred to today as design-bid-build. A design-bid-build approach to project procurement gives the owner more control over the final product and al-lows the contractor to know exactly what is expected of them before the work is constructed. As a result of this transition in project procurement, civil engineering schools placed a greater emphasis on the training of ?design? professionals. This article will document how the training of tunnel design professionals progressed within the United States. Although it is difficult to generalize about the hundreds of tunnels that were constructed in the first four decades of the 20th century, there is one project that stands out as having resulted in a university program related directly to tunneling and that is the Chicago Subway. During a visit to the United States in 1938, Dr. Karl Terzaghi met a student named Ralph Peck who was then studying at Harvard University in a pro-gram established by Arthur Casagrande. Shortly thereafter, Terzaghi traveled to Chicago for a lecture and was asked to consult on the Chicago subway project that was then under construction. The Chicago subway was being constructed in clay, and the owners were worried about possible settlements to nearby buildings. Terzaghi asked Peck to serve as his field engineer for that project. Thus was established one of the most productive relationships in the history of civil engineering in the United States. Peck, who would become Dr. Peck, moved to Chicago in 1939 to participate in an extensive research project that con-tinued until subway construction was halted in 1941 because of World War II. During that time, the cost of subway construction in Chicago was reduced substantially as a result of Peck?s observations and Terzaghi?s recommendations. In fact, it was reported that subway construction in Chicago cost less than one-half of similar projects in London even though the clay in London is considerably stiffer compared to Chicago. Upon the completion of his work on the Chicago Subway, Peck accepted a professorship with the University of Illinois in Champaign/Urbana.

Jun 1, 2010

By K. C. Kocsis

Underground ventilation systems, which require electricity to operate the fans and fossil fuel for heating in winter, can account for a significant portion of the energy consumption of mines. Recent studies have shown that the ventilation system in deep and highly mechanized metal mines could be responsible for 40 to 60 percent of their overall energy consumption. Presently, underground ventilation systems are designed for peak air volume requirements, which usually occur well into a future stage of the mines’ operating life. As a result, during their early operating stages, the intake air volume of the mines could be well in excess of their true air volume needs. Such ventilation systems could be considered as uneconomic, and to remain competitive the ventilation design needs to improve while the mines are trying to reduce energy consumption and their carbon footprints. This paper introduces a new mine ventilation design method where an underground base-metal mine’s ventilation system is designed by integrating discrete-event mining process simulation (DES) with mine ventilation modeling techniques. Furthermore, based upon the output data generated by means of discrete-event mining process simulations, the air volume requirement for the operating life of the mine is determined for “traditional” versus “activity-based” ventilation requirements. The output data generated through ventilation simulations are then used to quantify the economic and environmental benefits of an activity-based ventilation delivery system.

Jan 1, 2018

By Courtney Chamberlain

The Telfer Project, Australia's newest, largest and most remote gold mine, treats 480,000 metric tonnes of ore grading 9.33 grams per tonne derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded using a continuous strake, table and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, CCD and stellar filters for clarification and precipitate removal. Overall recovery into bullion averages 98 percent. The mill incorporates a number of design features which allow for maximum efficiency and security using a minimum number of operating personnel.

Jan 1, 1980

By Bo Hyun Kim, Mark K. Larson

Although techniques and practices of mining are highly advanced, coal pillar bursts or bumps continue to occur. Many uncertainties remain because of the highly anisotropic characteristics of coal seams that are associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous efforts are required to better understand the catastrophic failure mechanisms in coal mines. In this study, 3DEC modeling in conjunction with the Discrete Fracture Networks (DFNs) technique was performed to better understand the true anisotropic behavior of the specimens acquired from a bump-prone underground coal mine. The spatial characteristics of the dis- continuities (i.e., cleats and bedding planes) as input data for the 3DEC model are estimated based on the results of the laboratory tests and field observations. The DFNs explicitly generated the coal seam that was poorly or well cleated, indicating the different spacing between cleat apertures using the probability distribution functions for fracture density (or frequency) and size. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) are also considered by Monte Carlo simulations. Simulation results of laboratory tests using the 3DEC model and DFNs technique agreed well with the results of the laboratory tests. These calibrated results can be used as we seek to evaluate bump risk by modeling at field scale.

Jun 25, 2024

By John Callahan

A stream sediment (minus 80-mesh and minus 60-mesh panned concentrates) and lithogeochdcal survey for gold did not locate any Triassic-age placer deposits in the northern Wadesboro and southern Sanford basins in North Carolina. A stream sediment geochemical program for uranium funded by the North Carolina Energy Institute did identify one and anomalous site (8.5 ppm U; 5 ppm Th) near Covenington, North Carolina and eighteen possibly anomalous sites (1-1.6 ppm U) . Five of the eighteen samples with uranium levels in the 1-1.6 ppm range have high thorium levels (112-853 ppm) and may indicate a monazite source for the uranium. Gold values as high as .83 ppm in the stream sediments and 9.3 ppm in the panned concentrates were obtained during the survey. Small (<.5mm) flattened grains of gold (1-4 grains) were observed along with coarse kyanite and/or monazite in some of the panned concentrates. A distinctive pattern of high gold values in the sediments was observed in the vicinity of Mangum, N. C. where Minard (13) reported values as high as 2.1 ppm £ram a Triassic lithology. Follow-up gold analyses on over 400 rock samples from twenty-eight exposures near Mangum failed to obtain any high values (<55 ppb). The presence of coarse kyanite, monazite and gold in panned concentrates may be from a source younger than the Triassic lithologies that the streams currently drain or adjacent Paleozoic rocks.

Jan 1, 1979

By Stephen W. Kline

Rock suitable for crushed-stone aggregate is almost entirely restricted to the Highlands region of Arkansas, mostly from Paleozoic sedimentary units, but also from a few Cretaceous igneous plutons. Reserves in the state are sufficient for local needs, and Arkansas is geographically well situated for export markets to the south, where resources for crushed-stone aggregate are lacking. A study of 423 quarries, test pits, and exploration sites in Arkansas has been completed to evaluate the relative quality of bedrock units for producing crushed aggregate. Of these, 274 sites have records of engineering tests for stone evaluation done by the U.S. Army Corps of Engineers and/or the Arkansas State Highway and Transportation Department (AHTD). Of the 1,775 sample records from these sites, the most commonly reported parameters are the LA abrasion test and the Na-sulfate soundness test. Many records also have absorption and specific-gravity data, and, for some, petrographic information helps identify the potential for alkali-silica reactivity in portland-cement concrete. By determining the bedrock sources of the tested samples, comparison is made between the various geologic mapping units as to their relative quality for crushed stone.

Jan 1, 1999

By K. Komnitsas

Activities in the mixed sulphides industry, such as mining and beneficiation, cause adverse impacts to the environment due to excavation, treatment and disposal of low-grade ores and tailings containing residual sulphide minerals. The greatest impact is caused by the oxidation of sulphide phases contained in the tailings and waste rock and the subsequent production of leachates characterized by low pH and high concentration of heavy and toxic elements and sulphates, called acid mine drainage, that contaminates soils, surface- and groundwater. Therefore, rehabilitation of these sites is required in order to render these pollution sources inactive and minimize environmental impacts. The calculation of risk, based on acid mine drainage probability and magnitude of consequences at the disposal sites offers engineers, environmental scientists and authorities a valuable tool for the selection and application of the best remediation technology. Several parameters, such as the chemical and mineralogical properties of the wastes, the most probable pathways the contaminants follow, the potential receptors and the exposure scenarios have to be taken into account. Therefore, risk is the most critical parameter in decision-making regarding management of mining wastes and rehabilitation of disposal sites.

Jan 1, 2002

By Claude E. Wykes

Deep Well turbine pumps receive constantly increasing application to the problem of mining water and other fluids from great depths. Many installations of medium settings are presently operating successfully and it is felt that mach greater depths are immediately within reach. Settings and lifts in excess of 2000 feet: are not at all out of reason with present knowledge experience, and materiels; however, conditions of individual applications will govern in each case and dictate methods and possibilities to the designer. Design and operating problems of deep set -turbine pumps ire discussed together with a description of various types of equipment falling within this category. Although the deep well turbine pump has been produced In the vertical turbine pump industry for many years, the connotation of the word "deep" still remains questionable. Among the manufacturers of this type of machinery, answers to the question implying the practical limitation of setting for a deep well pump will vary to an extreme. Most pump designers are in accord that this type of equipment has not yet been exploited to its fullest degree; however, the subject is admittedly fraught with unsolved problems and un¬tried solutions so that such a discussion must necessarily derive from personal opinion and, belief., even though based on substantial experience and background. For this reason, it will be stipulated that the present writing will deal with what may be termed euphemistically ?a highly controversial subject.? During the nineteenth century, a paper was published under proper authority proving beyond question that the human body could not withstand speeds exceeding 20 miles per hour. As a limitation, this looks &apos; pretty ridiculous to us today. At the beginning of the twentieth century, there was not a single machine in operation that could be described as mullti-stage deep well centrifugal pump. As a matter of fact, very few centrifugal pumps of any type wire operating against heads in excess of 50 feet, since such applications were considered impractical. In the

Jan 1, 1960

By Timothy F. Markey, Brian C. Strohm

This paper presents a case study which applies risk assessment techniques in evaluating potential environmental problems associated with past waste disposal practices at a 65 acre non-ferrous metals and metal alloys manufacturing facility. Waste management activities at the site involved a number of surface impoundments for gangue material, neutralized acid rinse waters, acid rinse sludges, demolition debris, storm water runoff, stockpiled ores, and a permitted residual waste landfill. As a result of these activities, the She contained 9 identifiable waste management areas impacted by over 35 potentially hazardous chemicals and metals. Extensive environmental data obtained from investigations at the Site revealed heavy metal and volatile organic chemical contamination in various environmental media. These data were utilized to evaluate potential risks to human health and the environment. The human health risk assessment estimated potential health risks to workers, residents, and Site trespassers under current and expected future uses of the Site. Areas of the Site were identified which were considered to present potential health concerns under the various exposure scenarios. Results from the human health risk assessment were utilized to develop cost effective risk based soil remediation goals protective of the public health and environment.

Jan 1, 1992

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983

By Floyd M. Thorman

Gypsum is the crystalline chemical compound CaS04?2H20. A close chemical relation - and frequently occurring with Gypsum ? is Anhydrite which is Cask. Gypsun has wide commercial use because relatively simple heat processing reduces it to Plaster of Paris. While Anhydrite can be converted to Gypsum and thence to Plaster of Paris, the procedure is not simple and is quite costly. Anhydrite, however does have use in the agricultural field and in the Portland Cement industry. Occurrence of Gypsum in the earth structure is usually near or at the surface. Most underground mining is at 60 to 100 feet although one mine in southwest Virginia reaches a depth of 1300 feet. Gypsum is one of our softest minerals, rating only 2.0 on the Mohs scale of hardness. Specific gravity is 2.3 to 2.4. It is soluble in water but only slightly so. Interestingly, it is more soluble in cold water than in hot. For example, one part Gypsum dissolves in 370 parts water at 106° Fahrenheit while at 212°F. the water requirement is 452 parts. Compressive strength of massive Gypsum runs about 3000 lbs. per square inch. Color ranges from grey and brownish-grey to white.

Jan 1, 1973

By Prashanta K. Chatterjee

The planning of an underground coal mine requires a complex blend of technical expertise, experience and subjective design criteria implemented by the mining engineer. Currently the procedure is largely manual and requires considerable resources to generate a single mine plan. Often three or four people are assigned to work in the development of a single draft layout. Evaluation of the layouts is also tedious as it requires many repetitive calculations. The evaluation of layouts developed manually generally attempts to derive a single economically feasible solution. Operational constraints in underground coal mining such as manpower, time, equipment, etc, do not allow the generations of more than one alternative layout. As a result, the first plan is generally the only one considered. Computer-aided mine planning can automate many of the manual procedures and calculations involved in mine planning thus allowing to evaluate many layouts and mining strategies and to select the optimum plan with confidence. An optimized planning procedure will also provide the capability to evaluate mine performance continuously and critically, thereby helping to maximize return on investment.

Jan 1, 1986

By P. J. G. du Toi

Anaconda&apos;s experience with percussion longhole drilling in Butte, Montana, has consisted of six phases: 1. Drilling horizontal blast holes in stopes with push feeds. 2. Ring and parallel blast hole drilling in longhole stopes with bar mounted as well as skid jumbo mounted longhole drifters. 3. Ring and parallel drilling in raise climber shrinkage stoping using special raise climber drilling decks designed and built in Butte, Montana. 4. Parallel longhole drilling in horizontal cut and fill stopes with monorail jumbo. 5. Drilling water drain holes between mine levels. 6. Drilling leach holes through caved zones into old stope workings for leaching purposes. 7. Sample hole drilling.

Jan 1, 1970

By W. E. Adkins

Ore and waste haulage usually constitute one of the major cost items in the operation of an open pit mine. This has always been true at the Chino mine, one of Kennecott Copper Corporation&apos;s western mines, located in southwestern New Mexico. The Chino Mines Division is an integrated operation. The open pit mine, dump leaching operation, and a precipitating plant are located at Santa Rita, New Mexico, and a power plant, mill, smelter, and fire refinery are located in Hurley, New Mexico, about nine miles south of the mine. Approximately 22,000 tons of ore are mined and processed each day; in addition, approximately 42,000 tons of waste are removed from the pit. Originally the pit was located along the side of Santa Rita Creek but it has deepened and expanded so that at the present time, it could better be described as a nearly circular pit about one to 1.5 miles in diameter. The bottom is at an elevation of 5750 feet, the west rim near the ore gathering yard is at an elevation of 6230 feet, and the highest bench on the east side of the pit is at an elevation of 6750 feet, giving a vertical mining depth of 1000 feet. The train waste dumps reach a maximum elevation of 6580 feet. At the present time, Chino uses electric locomotives, off-the- highway trucks, and a skip system for mine haulage.

Jan 1, 1963

By Douglas J. Lootens

Geologic mapping was undertaken in the Sierrita Mountains as part of a Doctoral program at the University of Arizona, Tucson. During the study, approximately 35 square miles was mapped in detail, with particular attention given to specific areas of great or significant structural complexity and their relation to mineralization in the vicinity. A combination, of field studies and photogeologic interpretation was used in order to define regional and local structural controls for disseminated copper-molybdenum mineralization in and adjacent to the study area. Gratitude is expressed to the faculty of the University of Arizona, Department of Geology for their assistance in this work and to Bear Creek Mining Company for making numerous reports and drill cores available for study.

Jan 1, 1965