Search Documents

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Southwestern New Mexico is part of a large belt of Late Cretaceous to Eocene copper porphyry deposits found in Arizona, New Mexico, and Mexico. These deposits are the result of arc magmatism that occurred during the Laramide orogeny. Recently, attention has been brought to other commodities that can be extracted as by- and co-products, many of which are critical minerals. A new compilation of the geochronology of these deposits shows two main pulses of magmatism that produced mineralized deposits and, along with new dates by the author, shines new light on the geologic history of these deposits and the role it plays in critical mineral abundance.

Feb 1, 2024

By D. Hong

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant has been studied. Experiments were carried out in an autoclave. The effect of stirring speed, temperature, pH of the solution, iodine and iodide concentrations on the dissolution of rhenium was investigated. It was found that high temperature and high pH of the solutions were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by mass transfer of iodine with an apparent activation energy of 15.77 kJ/mole.

Jan 1, 1997

By W. Hustrulid

"In recognition of his inspiring dedication to the mining industry through education, research contributions and dissemination of practical knowledge, exceptional leadership and excellence in mining engineering practice and for his lecture, “You can't make a silk purse out of a sow's ear.” Recipient of the 2002 D.C. Jackling Award Introduction It is always difficult to decide on the most appropriate title to give to a paper or talk. It is a particularly difficult decision in the case of the Jackling Lecture, because the title becomes part of the award citation. I hope that the significance of this unusual title will become crystal clear as you read the pages that follow. However, to assist you in this journey, I will provide the following few words of guidance. In making a cake, you need the proper ingredients. If one or more of them are missing, it will not be a cake. In addition, the quality of the cake depends on the quality of the ingredients. In my lecture, the "cake" is the U.S. mining industry of the future. A national perspective President George W. Bush in his State of the Union Address (Bush, 2002) delivered on January 29, 2002, defined three national objectives: •win the war on terrorism, •protect the homeland and •revitalize the economy. Under the heading "revitalize the economy," he indicated the importance of "good jobs" and "energy production" by saying: "Good jobs begin with good schools. Good jobs also depend on reliable and affordable energy. This Congress must act to encourage conservation, promote technology, build infrastructure and it must act to increase energy production at home so America is less dependent on foreign oil." I wish that he would have broadened his focus and stated instead that: "This Congress must act to encourage conservation, promote technology, build infrastructure, and it must act to increase materials production at home so America is less dependent on foreign sources." With regard to jobs, all jobs are not equal. To paraphrase John Reeves of MidContinent Resources (Reeves, 2002): "If our nation is to prosper, we all cannot make a living by doing each other's wash. Some of us, at least, must be actively engaged in the primary production of raw materials from the riches of the earth and other Americans must turn those materials into consumer products." The unfortunate trend in our country has been to neglect the primary production of basic materials, even those coming next in line. We have left those responsibilities to others while we concentrate instead on performing various services, i.e., doing each other's wash and flipping burgers. This cannot continue. It must be remembered, especially by those in leadership positions, that all "jobs" are not created equal. Some jobs are much more essential to the security and wellbeing of our country than others. We must be sure that the important ones are in place. We cannot produce the basic materials that our nation requires without access to those materials. This leads to my Proposition 1: You cannot have a viable mining industry without a clearly enunciated, positive U.S. materials policy. Background regarding U.S. materials policy Resources for freedom. In January 1951, President Truman created the President's Materials Policy Commission, with William S. Paley as chairman. As expressed in the invitation letter from the president to Paley: This commission, within the executive office of the president, is to study the broader and longer-range aspects of the nation's materials problems as distinct from the immediate defense needs. The task of the commission is to make an objective inquiry into all major aspects of the problem of assuring an adequate supply of production materials for our long-range needs and to make recommendations that will assist me in formulating a comprehensive policy on such materials. The commission should study, together with any other aspects deemed by it to be pertinent, such questions relating to production materials as: - the long-range requirements outlook; - the long-range supply outlook; - the prospect and estimated extent of shortages; - the consistency and adequacy of existing government policies, plans and programs; and - the consistency and adequacy of private industry practices.

Jan 1, 2003

By C. E. Jordan

Direct digestion of phosphate ores by the acid-alcohol method offers improved leaching selectivity for the exclusion of iron and aluminum in the product acid. The leaching kinetics of this process will have a major role in the eventual application of this technology. The Bureau of Mines investigated apatite dissolution to determine the reaction rate and mechanisms of the leaching kinetics. The dissolution kinetics were monitored on various sized fractions of pure apatite. The "shrinking-core" kinetics model was applied to the data to determine the rate controlling mechanisms. For each size fraction, the initial reaction rate was controlled by the dissolution reaction. After an hour the dissolution rate slowed indicating a diffusion controlled reaction caused by the formation of calcium sulfate hemi-hydrate coating on each particle. For complete dissolution of the apatite, the phosphate rock should be ground to near 10 µ m size.

Jan 1, 1993

By J. F. Snyder

Minor elements determined by atomic absorption spectroscopy include: zinc, cadmium, copper, cobalt, nickel, chromium, manganese, and iron. Of these elements, only three; zinc, cadmium, and copper are found to have been introduced with the ore-forming fluids. Iron, manganese, chromium, and nickel were increased in dolo-stone lithologies when compared to limestone lithologies. The uniform distribution of cobalt suggests this element was neither increased nor decreased during ore emplacement nor during dolomitization of the rocks. Zinc increases adjacent to ore result from leakages into open spaces rather than as pervasive aureoles surrounding ore bodies.

Jan 1, 1977

By V. Srivastava, T. Ghosh

The modeling and simulation of semiautogenous (SAG) mills have been widely used in the design and optimization of mill performance in terms of its power draw, processing capacity and product size distribution. However, these models are solved under steady approximation and do not provide any information on mill charge distribution in real time. 7KLVSDSHUDWWHPSWVWRFKDUDFWHUL]HPLOOFRQWHQWVE\VROYLQJ:KLWHQ¶V¿UVW RUGHUFRQWHQW EDVHGPRGHOLQWKH0$7/$% Simulink environment. The parameters in the model, such as breakage rate constant, discharge rate and appearance function, were estimated using process and design data collected from a gold mine operating in Alaska coupled with a nonlinear parameter estimation scheme. This model was then used to predict the dynamic responses of other key operational variables, such as mill power, bearing pressure, charge level and product size distribution. The transient response of mill behavior with respect to changes in feed size distribution, tonnage and mill feed water is also presented. This dynamic simulation approach can be used for practicing different control strategy and training purposes. The observed response of mentioned variables was validated using dynamic response data from the plant to encompass operational characteristics of SAG mill behavior.

By K. S. Gritton

The U.S. Bureau of Mines has investigated methods for extracting metals from a variety of arsenic-containing smelter flue dusts. One proposed flowsheet includes a sulfuric acid leach, a cooling step to precipitate hydrated copper sulfate, and a reduction-precipitation of As2O3. Arsenic extractions greater than 90 pct were achieved, while copper extraction ranged from 50 to 85 pct under the conditions examined. Copper was removed from the leach solutions by crystallization followed by SO2 precipitation of arsenic which resulted in a 98 to 99.9 pct As2O3 product. Other metals, such as lead and zinc, were concentrated in the leach residue or in other byproduct streams for recovery of their valuable metal contents.

Jan 1, 1990

By Roger Storry, Donald Bruce, Arnaud Hochart

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands and under the main shipping channel in Biscayne Bay (Figure 1).The POMT was a unique project which embodied many technical firsts and involved the first large diameter tunnels constructed through Florida’s challenging sedimentary carbonate strata. At the outset, a comprehensive ground investigation was performed, using both conventional and less conventional investigation techniques, to characterise the highly heterogeneous ground conditions.The findings of the investigation had a major impact on the tunnelling methods, triggering a series of mitigation works to ensure that the tunnels could be excavated safely and effectively. The mitigations included modifications to the already designed Tunnel Boring Machine (TBM), to facilitate an innovative excavation process, and a unique grouting campaign (Storry et. al. 2013a). The project was completed and opened to traffic in August, 2014 and has significantly alleviated traffic congestion in Downtown Miami.GEOLOGICAL CONTEXTThe geological conditions at the project site consist of carbonate sediments which can be divided into distinct geologic units; the Miami Limestone Formation (Layers S3, S4), the Fort Thompson Formation (Layer S5), the Anastasia Formation (Layer S6), the Key Largo Formation (Layer S7) and the Tamiami Formation (Layer S8). Multiple changes in sea level over a relatively short geologic time scale have resulted in a heterogeneous profile consisting of interbedded sedimentary rocks and sediments, which vary widely, both vertically and laterally (Figure 2)."

Jan 1, 2016

By Adil Jamali, Taufiq Hidayat, Imam Santoso, Zulfiadi Zulhan, Indah Suryani

The study investigates the segregation of iron and titanium in iron sand concentrate pellets reduced using coal under an isothermal-temperature gradient profile. The results show that metallic iron migrates to the surface while titanium and other oxides move to the center of the pellet. The study provides insights into the reduction process and the behavior of iron and titanium during heat treatment.

Mar 2, 2022

By Daniel F. Meyer, William C. Paschen

INTRODUCTION The problems involved with moving millions of tons of rock are being addressed by nationally recognized tunnel contractors who have converged in Chicago over the past 5 years. This wealth of expertise has been needed to meet the risk and challenge of constructing the world's largest network of underground tunnels which in turn has required a dramatic advance in the art and science of tunneling. These pioneers, through innovation, adaptation, and hard work, have eliminated the one major concern of The Metropolitan Sanitary District of Greater Chicago - how to move 8 million tons of rock. The Metropolitan Sanitary District of Greater Chicago (MSDGC) serves 122 municipalities covering 866 square miles in Cook County, Illinois. Of these cities, towns, and villages, 53 have combined sewer systems. On an average of once every four days, these systems overflow about 4 million gallons of combined sewage and rainwater into the area's rivers and canals. The overflows occur at approximately 640 outfall locations of which 10% are owned by the MSDGC, with the remainder of the points belonging to various other municipal bodies. All those who own these "point" sources of pollution are in violation of Illinois State and Federal regulations. To enable its member municipalities to come into compliance with State and Federal law, the MSDGC is implementing its Tunnel And Reservoir Plan (TARP). TARP is a regional solution to the problem of combined sewer overflow in the metropolitan Chicago area. TARP will greatly reduce the pollution of area waterways by intercepting the combined sewage and rainwater carried in the existing sys-

Jan 1, 1981

By Sah Rameshwar, T. Umadevi, K. S. SRIDHARA

In the magnetite iron ore pelletization process, oxidation of magnetite followed by sintering of the oxidized magnetite (hematite) is desirable. Optimum preheating time & temperature and roasting time & temperature is required to get the desired properties of the pellets with magnetite, hematite, and hematite–magnetite blend. In order to utilize the magnetite resources in a current induration furnace, which is designed for hematite resources, detailed pelletization studies have been carried out to optimize the firing cycle for magnetite concentrate as well as magnetite with hematite concentrate. Under optimum conditions, such as preheating temperature 1000–1150 °C, preheating time 10 min, roasting temperature 1250 °C and roasting time 7.5 min, the cold compression strength (CCS) of magnetite roasted pellets was 325 kg/p, and this was due to recrystallization of secondary hematite particles, and development of the strong slag bond between primary and secondary hematite particles. The strength of hematite concentrate pellets was 260 kg/p. From laboratory studies, it was found that without disturbing the induration furnace firing cycle, which is designed for hematite ore ~5%, magnetite concentrate can be used along with hematite concentrate in pellet blend and the strength of the pellets was 270 kg/p. As the magnetite concentrate increases in the blend beyond 5%, the preheating zone residence time should be increased or a supply of extra oxygen is required. Laboratory as well as plant investigation has shown that the addition of magnetite to the hematite mix blend improved the strength of the pellets compared to hematite pellet alone.

Oct 26, 2020

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Morgana Rosset, Bárbara da Rocha Pereira

High-purity alumina finds application in various electronic industry sectors, with approximately 100 million tons of this compound being produced worldwide. Alumina is acquired through the mining process of bauxite, a rock composed of a mixture of minerals such as gibbsite, kaolinite, hematite, and either anatase or rutile. In 2020, both bauxite and alumina were included in the list of critical raw materials. Due to the demand for high-purity alumina production, the development of a methodology to remove impurities present in the leach liquor from bauxite processing by solvent extraction (SX) followed by precipitation has been widely studied. This work aims to obtain high-purity alumina from bauxite by a solvent extraction process followed by a precipitation step from the sulfur leach liquor obtained by the thorough dissolution of Al and Fe from bauxite. Different parameters were evaluated in the SX step, such as extractant type, pH, temperature, and volume-to-volume ratio. The results indicated that using Alamine 336 as an extractant at pH 0 and room temperature led to an extraction of 90% of Fe and 15% of Al. Aluminum sulfate was completely precipitated as aluminum hydroxide and 55% of Fe using NH4OH. After the calcination procedure, obtaining a 99.9% pure alumina was possible without generating a red mud-similar residue.

Dec 28, 2023

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By William H. Langer

I spent 41 years as a geologist with the US Geological Survey (USGS) conducting geologic studies and preparing peer reviewed maps and reports describing the results of those studies. Since retiring from the USGS in 2011, I have been a consultant specializing in aggregates and other industrial minerals. Consequently, I have had the opportunity and pleasure to apply the information contained in those kinds of geologic maps and reports to real-life situations. About half of my consulting is performing due diligence for mineral resource evaluations of one type or another where resource information has been provided by the property owner. Many of those jobs necessitate that I conduct desktop studies followed by field work. I then use my information to review and comment on the written reports of others; reports variably referred to as geologic reports, resource studies, reserve analyses, and so forth. While there are many well written reports addressing geologic resource issues, I was surprised to see that there are also a significant number of so-called geologic reports that only pay cursory attention to geology. Unfortunately, that lack of rigorous geologic investigation commonly leads to erroneous conclusions. This paper addresses three such reports covering concrete sand, metallurgical gravel, and proppants (frac sand). Although all three examples are located in the Gulf Coastal Plain Province, I do not reveal the exact location of any of the properties for purposes of confidentiality. Furthermore, I have generalized the site descriptions and illustrations. However, all the descriptions faithfully define the geologic situation.

Feb 1, 2024

By Sahin Furkan Sahiner, Onur Golbasi

Effective maintenance planning is vital for coal mining operations, where haul truck fleets directly determine production continuity. This study presents a discrete event simulation (DES) model for evaluating maintenance strategies under multiple failure modes and their interdependencies. The model integrates corrective, periodic preventive, and opportunistic maintenance, dynamically updating equipment lifetimes through probabilistic time-betweenfailure and time-to-repair distributions. Applied to a fivetruck coal haulage fleet over a one-year horizon, results show that periodic preventive maintenance delivers the highest availability (76%) under unconstrained conditions, slightly outperforming corrective-only maintenance (75%). Opportunistic and integrated approaches performed worse (68% and 69%), reflecting redundancy from overlapping interventions. These findings suggest that structured preventive programs provide the most reliable outcomes when costs and resources are not limiting. The DES framework serves as a baseline for future models incorporating cost, spare parts logistics, and workforce availability, supporting robust maintenance planning in coal mining operations.

Feb 22, 2026

By C. Garcia, A. Potulska, J. J. Opazo, T. Comi

"The Sierra Gorda SCM sulfide ore processing plant began commissioning in the third quarter of 2014. Located in the Atacama Desert in northern Chile, the project is an open pit mine and Copper-Molybdenum processing plant is one of the most highly-instrumented operations in the world. It is the first hard rock operation in Chile and the second in South America to utilize HPGR technology. It is a significant Molybdenum resource especially in the first five years and the Molybdenum separation plant is complex. Designed to process up to 60 million lbs. of fine Molybdenum per year, it uses the latest technology and equipment to ensure superior recovery and product quality. It also has gas handling and alarm systems to fulfil the Company’s vision of “Zero Harm”. This paper discusses the overall operation and issues relating to the concentrator start-up. These include a review of the mineral processing design, the unified process control center and management information systems, and the correlation of geological and metallurgical performance data (mine-to-mill) for use in anticipating and preparing for treatment of diverse ore deliveries. INTRODUCTION Sierra Gorda SCM is a joint venture partnership with KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining, and Sumitomo Corporation (Japan) operating in northern Chile. The Sierra Gorda open pit mine and Copper-Molybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, well-instrumented mine in Chile. This paper contains a general review of the project including geology and history. This was a very fast-track project going from greenfield site acquisition to mill start-up in 10 years. Highly-experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied. The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (see Figure 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km from the village of Sierra Gorda at an elevation of approximately 1,700 m above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic, and Escondida, to name a few."

Jan 1, 2015

By Deepak Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet auditing can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1986

By N. A. Frazier

The goal of the U.S. nuclear waste management program is to provide assurance that existing and future nuclear waste from military and civilian activities, including spent fuel from the once-through nuclear power cycle, can be isolated from the biosphere so as to pose no significant threat to public health and safety. The U.S. Department of Energy (DOE) is responsible for defining and implementing this national waste management effort. The Environ- mental Protection Agency (EPA) and the Nuclear Regulatory Commission (NRC) are responsible for providing a framework of criteria, standards, and regulations that will assure that the disposal methods developed by DOE are consistent with the achievement of the goal of safe, long-term waste isolation. Within DOE, the responsibility for implementation of the national waste management program rests with the Office of Nuclear Waste Management. The nuclear waste management effort involves three major activities: The Defense Waste Management Program, the Spent Fuel Storage Program and the Commercial Waste Management Program. The major programmatic effort in the Commercial Waste Management Program is the National Waste Terminal Storage (NWTS) Program.

Jan 1, 1981

By Norman E. Lehman

INTRODUCTION The Washington Camp - Duquesne mining district is located on the east flank of the Patagonia Mountains, 98 kilometers south of Tucson and within 5 kilometers of the International border (Figure 1). Since the development of high-grade silver and copper ores by settlers in 1862, the Washington Camp - Duquesne district has yielded an estimated 450,000 metric tons of ore. The mined ores averaged 8% zinc, 2% copper, 3% lead and 124 grams of silver. REGIONAL GEOLOGY The Patagonia batholith, of Laramide age, crops out in the core of the Patagonia Mountains intruding Precambrian granite, Paleozoic sediments and Mesozoic igneous, volcanic and clastic rocks. This granodioritic batholith lies in a northwest-trending zone of Laramide plutonic rocks, which can be traced for a distance of 320 kilometers from the Nacozari district in Sonora, Mexico to the Silver Bell Mountains west of Tucson, Arizona. Several major porphyry copper systems occur within this plutonic belt including the Red Mountain deposit found at the northern end of the Patagonia Mountains. Data from more than 80 mineral deposits within the Patagonia Mountains show metal zoning symmetrical to the Patagonia granodiorite (Graybeal, 1975). Disseminated copper-molybdenum deposits occur within the batholith. Pyrometa-somatic, limestone replacement and vein deposits of copper, lead, zinc and silver occur in the wallrocks adjacent to the. granodiorite and epithermal manganese-silver deposits occur at the outer periphery of economic mineralization. GEOLOGY OF THE WASHINGTON CAMP - DUQUESNE DISTRICT Stratigraphy Nearly 900 meters of miogeosynclinal Permian and Pennsylvanian sediments are exposed in the district (Figure 2). In addition, 700 meters of older Paleozoic rocks crop out 6 kilometers north of the district. The Paleozoic rocks occur in fault contact with a sequence of Triassic-Jurassic pyroclastic and flow rocks, ranging in composition from latite to rhyolite.

Jan 1, 1977

By Peter Bush

The deposition of metastable carbonate minerals in ar. aid, sheltered, coastal environment, leads to the formation of a flat, coastel, sabkha plain. The ground waters of the sabkha plain are modified by evaporation, precipitation of salts and reaction between ions in solution and the host carbonates. The resulting brine is similar to those found in fluid inclusions associated with Mississippi Valley type deposits. The aragonite and high magnesium calcite found in the sediments can concentrate lead and zinc from sea water. On diagenesis the lead and zinc are released into the sabkha brines.

Jan 1, 1979