Search Documents

By Gary Peach, Khalid Saif Al-Khayareen, Vigil Fernandez, Furqan Hameed

The Musaimeer pump station and outfall project (MPSO) is in Doha Qatar. This technical paper will discuss and explain the three major stages of geotechnical investigation employed. Stage one the tender geotechnical data and how this was used to design the TBM and identify various areas of risk. Stage two was the selection of supplementary geotechnical investigation methodologies. Stage three was the geotechnical investigation by specialist equipment installed on the TBM and providing further data on a real time basis as the TBM was advancing. Analysis of all the data will be provided along with the lessons learned.

Jun 23, 2024

By S. S. Peng

To prevent mine floor heave, the mechanisms of floor heave must be fully understood. Based on the field study, the mechanisms of two types of floor heaves are analyzed in this paper. The mechanical models for the two types of floor heaves are developed. The floor heave can be predicted by the developed mechanical models and the control measures are recommended.

Jan 1, 1995

By Salvatore] [Parand

Deep well disposal is a much used and abused term which is the panacea for wastewater disposal in some minds and creates near hysteria in others. It can be the answer to a difficult waste disposal problem, or if improperly employed, can create more problems than it solves. My purpose in this presentation is to focus on the value and limitations of deep well disposal as expressed by New York State's experience and policies. To he sure, I feel a place for such practices docs exist if adequate safeguards are utilized. I shall give a broad brush approach to New York's legislative, geologic and operational concerns and speak briefly on some case histories. I shall not delve deeply into the technological details since I am not an expert in mining exploration or well drilling.

Jan 1, 1973

By Earle Faig

Along with other transportation modes, the barge industry will be greatly effected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events have caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of our long experience in moving large quantifies of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to the barging industry. Barge companies operate on a 40.23-Mm (25 000 mile) river system which includes the East and West Coasts and the Mississippi River System. Included in the Mississippi River System are the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior - Tombigbee and Mobile Rivers as well as some smaller tributaries. The Gulf Intracoastal Waterway, which stretches along the Gulf Coast from Brownsville, Texas to Apalachicola, Florida, is also considered part of the inland waterway system.

Jan 1, 1981

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021

Researchers at National Institute for Occupational Safety and Health (NIOSH) are investigating how fiber-reinforced shotcrete mix designs can be extrapolated from proven designs employing wire mesh. This paper explains the results of round determinate panel tests and relates the flexural strength and toughness of fiber-reinforced shotcrete to known energy absorbing properties of wire mesh. The energy absorbed with central deflection is strongly influenced by the amount of fibres. The higher the energy absorption the more load cracked shotcrete can support. Two types of fiber-reinforced shotcrete were investigated, one with steel fiber and another with polyfiber. The residual load supported in Round Determinate Panel Tests can be matched with the strength of wire mesh, thus providing equivalent bag strength values for fiber reinforced shotcrete panels. There is also evidence of a panel crack width comparison to the load holding capabilities of the fiber in the shotcrete mixes. In practice, this provides designers with a method for comparing the ground support provided by fiber-reinforced shotcrete with that supplied by wire mesh.

Jan 1, 2010

By Joe Hachey, Jerry Dorn, Jeff Schutt, Derek Penrice

"Sound Transit’s East Link Project, a $3.7 billion (2015 $), 14-mile light rail extension, will connect downtown Seattle with the rapidly developing east side cities of Bellevue and Redmond. Among the most technically challenging aspects of the Project is the 2,435 foot long Downtown Bellevue Tunnel (DBT), which will be constructed through the central core of Bellevue underneath 110th Avenue NE using a combination of Sequential Excavation Methods (SEM) and cut and cover tunneling. The 1,980 foot long central SEM component of the DBT will be mined at shallow depth through challenging and complex geology, comprised of glacially overconsolidated soils, containing both regional and perched groundwater conditions and in close proximity to existing high rise buildings. The paper shares lessons learned from the planning decisions and risk based approach to the investigation, design and procurement processes which shaped the DBT configuration and enabled a successful transition to the project’s construction stage. INTRODUCTION The East Link Project is a voter-approved $3.7 billion (2015 $), 14-mile extension of the existing Sound Transit (ST) light rail transit (LRT) system from downtown Seattle, across Lake Washington via I-90, to the cities of Bellevue and Redmond on the east side of Lake Washington. With targeted completion in 2023, East Link will provide riders with an efficient and reliable connection between the largest population and employment centers on the east side and downtown Seattle. The project alignment is indicated in Figure 1 below.ST completed the Preliminary Engineering (PE) phase of the East Link project in late 2011. Subsequently the final design contract for the easternmost seven miles of the project was awarded to the H-J-H Team, a joint venture comprised of HNTB, Jacobs Engineering and Hatch Mott MacDonald in February 2012. H-J-H’s final design scope includes approximately 7 miles of double-track LRT between the east end of the I-90 East Channel Bridge and the Overlake Transit Center Station. While the project scope is extensive and diverse, the focus of this paper is the DBT. The DBT is located immediately north of the East Main Station, and travels approximately one half mile through downtown Bellevue under 110th Avenue NE between Main Street and NE 6th Street; terminating at the Downtown Bellevue Transit Center (BTC) Station. The location and extent of the DBT is indicated in Figure 2."

Jan 1, 2016

By A. F. Grandt

What is prime farmland? Can such land, once it has been strip-mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on strip-mined land in St. Clair County (1). This research was done almost 30 years before requirements of Public Law 95-87 were passed by the United States Congress and signed August 3, 1977.

Jan 1, 1980

By M. Gunter, M. Buzon

"Talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic, and lacking in amphiboles. In southwest Montana, talc formed from hydrothermally altered dolomitic marbles, and is still actively mined. These talc deposits are typically in contact with quartzofeldspathic gneiss and marble. Accessory minerals vary between these rocks and the ore producing body; the identification and characterization of such minerals requires carefully selected analytical methods. Recent litigation and ensuing confusion over the petrology and asbestos content of these deposits challenges the talc mining industry in Montana, and elsewhere in the world. INTRODUCTION Commercial talc has been mined from the deposits in southwest Montana since the 1940s, and by 1956 the region had output 200,000 tons of talc ore (Chidester et al., 1964). Commercial talc refers to rocks containing more than 20% of the mineral talc (McCarthy et al., 2006); the ores from Montana typically contain upwards of 90% talc. This region remains the leading domestic source of talc in the U.S. partly due to the reserves in the area, and partly due to the diagnostic purity of the ore compared to that of other regions, some of which are no longer actively mined. The mineral talc, a sheet silicate, is expressed by the formula Mg3Si4O10(OH)2, and therefore can form in geologic environments that are rich in Mg, Si, O and water. The protolith for the talc deposits in southwest Montana is a dolomitic marble, but other common protoliths include ultramafic igneous, mafic igneous, and siliceous dolomites (McCarthy et al., 2006). Physical properties such as hardness of 1 on Mohs hardness scale, white streak and slippery feel are among some of the reasons why talc is so widely used as fillers in a number of industries. In decreasing order, ceramics, paper, paint, roofing, plastics, rubber, and cosmetics are the leading domestic industries that use talc despite the decreasing trend in U.S. talc use and production since 1994 (Virta, 2015). The purpose of this paper is to describe the mechanism of talc formation in southwest Montana by focusing on talc deposits and surrounding rocks in the Ruby, Greenhorn, and the Gravelly Ranges, and to relate the mechanism of formation to the composition of talc ores. The compositional data show mineral content of selected ores, and the major and trace element content of those minerals, specifically talc. Our electron microprobe (EPMA), powder x-ray diffraction (XRD) and x-ray fluorescence data for samples from five mines in these three ranges provide continued evidence of the purity of these ores despite claims made during recent litigation that these ores contain asbestos. The five mines that we discuss include the Beaverhead, Treasure, Regal, Willow Creek, and Yellowstone Mines (Figure 1.)"

Jan 1, 2016

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986

By William C. Dixon

Since the mid 60's, several haul cycle simulation programs have been developed. However, most of these programs are believed to employ the continuous, rather than the discrete, event-oriented simulation approach to determine the haul cycle times. This paper describes the recently developed haul cycle simulation approach where time is advanced in varying amounts only as the system changes occur. This approach results in greater computational accuracy and increased computational efficiency. The program is written in FORTRAN and requires equipment performance curve and haul road profiles as input. Unique program capabilities include the handling of switchbacks and intersections. The program uses a master data file concept in which various haul road profiles found during the mine life can be simulated all in one job submission. The results of the model validation using the actual time study data provided by an open pit mine operator near Tucson, Arizona, are also described in this paper.

Jan 1, 1978

By Weibai Hu

Four methods to assess the relative flotability of fine coal have been tested: flotation with frother only, flotation with frother and collector, salt flotation, and timed-release analysis. A practical and simple criterion which combines the separation efficiency (capacity factor and kinetic rate constant (intensity factor) has been suggested. Five coal samples are chosen and tested. Based on test results, it is concluded that the flotability test with collector and frother is closer to practice, and, according to the suggested flotability criterion, coal fines can be classified into four categories of relative flotability: very easy, easy, moderate, and difficult.

Jan 1, 1987

By K. T. Valsaraj

The separation process called solvent sublation for the removal of two hydrophobic compounds (penta-and tri-chlorophenols) from the aqueous phase is discussed. A steady state mathematical model for the process is discussed. The process was conducted in a continuous countercurrent mode. The underlying mechanisms, theory and experimental details on the effects of process variables on removal efficiency are reported.

Jan 1, 1992

By Gary A. Nowlan

The Casa Grande West-Santa Cruz porphyry-¬copper deposit is in the Basin and Range physiographic province west of Casa Grande, Arizona (Fig. 1). The Casa Grande West portion of the deposit is controlled by Casa Grande Copper Company and the Santa Cruz portion by ASARCO. The deposit contains at least 350,000,000 metric tons of rock with greater than 1 percent Cu. The deposit is covered by at least 300 m of sediment, with no visible expression of the deposit at the land surface. The deposit is in an area of prime agricultural land that depends heavily upon well irrigation because of a hot and arid climate. Because of the deep sedimentary cover, the chance is extremely remote that the geochemistry of soil or stream sediment would reflect the deposit even if the land surface were not disturbed by many years of farming. Irrigation wells of the area generally bottom in the sedimentary cover. The purpose of the study is to see if the Casa Grande West-Santa Cruz deposit is geochemically reflected in ground waters over and near the deposit.

Jan 1, 1981

By A. D. Kalogeropoulos, T. N. Michalakopoulos

This paper deals with the numerical simulation of rock cutting laboratory tests using the discrete element method. The main objective is to provide a method for calibrating numerical DEM models of rock cutting in a systematic way so that realistic results are yielded. The numerical models are developed with the discrete element code Yade, which models rocks as a collection of bonded spheres. The models are calibrated in a four-step process based on the design of experiments method and optimization. The calibrated models are evaluated both quantitatively and qualitatively against actual laboratory cutting tests, in terms of the ratio of the simulated mean cutting force to the actual one and the cutting force time series, respectively. The fully calibrated models showed that the simulated cutting process matched qualitatively the actual cutting force recordings and underestimated the mean cutting force by approximately 3%. It is concluded that well-calibrated numerical simulations of the rock cutting process can provide not only a better understanding of the process itself but also quantitative data regarding the cutting force and energy requirements.

Dec 28, 2022

By Richard E. Beane

For several decades, the minerals industry has used leaching techniques to extract metals from rocks whose grade was too low to be treated profitably using conventional metallurgical techniques, and, as of 1972, about 15% of domestic copper production was derived using leaching methods (Beall 1). Increasing interest is currently being directed toward solution mining, particularly with respect to copper, for basically two reasons. In the first place, geological exploration has outlined several copper deposits of large tonnage and 1m', grade which are buried at sufficient depth to preclude open-pit mining which would make such mineral deposits ore deposits. Nevertheless, these occurrences provide significant potential if they could be treated by chemical leaching in situ. Secondly, the porphyry deposits of the western united States, which provide by far the largest percentage of domestic copper, do not terminate geometrically with sharp borders. These large disseminated bodies commonly decrease in grade laterally away from volumes of rock containing ore grade metallization, and the distinction between ore and waste is strictly economic. In order to extract ore grade material from the ground, a significant amount of rock containing sub-ore-grade copper must also be removed which, when placed on dumps, is amenable to solution mining. These two considerations clearly indicate the reasons for the growing interest in solution , leaching techniques--namely the ability to exploit deeply buried low grade deposits and the expansion of reserves in deposits currently under production.

Jan 1, 1977

By Sotiris Psomas, Colin M. Eddie

"Steel Fibre Reinforced Concrete (SFRC) Segmental Tunnel Linings have successfully been used for over 20 years in the UK and have been adopted in a number of high profile projects such as High Speed 1, Crossrail, Thames Tideway, as well as High Speed 2. Tunnel linings and especially SFRC design are not covered in the Eurocodes. This shortage of SFRC tunnel design rules seems to be partially addressed by several international publications. However, in the UK, the ‘design-assisted by testing’ (DAT) approach has also been adopted. The Paper discusses the UK’s best design practice and focuses on the DAT methodology as applied in the case of the 6.9km (4.3miles), 7.8m (25.6 feet) ID Lining for the £635million Lee Tunnel Project. The design approach, the full scale testing at the Building Research Establishment (BRE), and the construction innovations are presented. This experience will be transferred to the £4billion Thames Tideway Tunnel.INTRODUCTIONSteel Fibre Reinforced Concrete (SFRC) has been used for Tunnel segments for more than 20 years. The first application of SFRC in the UK was for the Heathrow Baggage tunnel (1994). Since then significant size tunnels have been designed and constructed, such as the Jubilee Line (1999) High Speed 1 (CTRL, 2006), Crossrail (2014), Lee Tunnel (2014) and the scheduled 25km Thames Tideway (‘Super Sewer’) and High Speed 2 rail tunnels. However one the main obstacles in achieving streamlined design and improving efficiency are the lack of appropriate design guidelines for SFRC tunnel segments. This issue will – to some extent – be addressed by a number of current documents on tunnel FRC design either being produced by BSi (PAS8810, expected 2016), ACI (544.R) and ITAtech (Design Guideline PCFRC, 2015) in an effort to advance the design of SFRC and take into consideration the recent developments in Steel and Macro-Synthetic FRC technology."

Jan 1, 2016

By Ahmed M. Yousif, Walid M. Abdellah, Galal M. Abdel Wahab, Amal E. Mubark

The present work is concerned with selective dissolution of niobium from Gabal El Faliq concentrate sample by using fluoridefree process. The chemical analysis of concentrate sample revealed the presence of high amount of ZrO2, Nb2O5, Re2O3, and HfO2 assaying 33.6, 1.99, 4.8, and 1.2%w/w respectively. Several economic minerals including zircon, samarskite, fergusonite, and xenotimewere recorded in the studied sample. About 98%of Nb content was selectively dissolved at the optimumconditions of 1:2 concentrate sample: KOH weight ratio, 2.5 h fusion time, and fusion temperature of 550 °C. Organic solvent extraction process using Aliquat 336S in xylene was effectively used for preparing pure Nb2O5 (98.95%).

Oct 22, 2019