Search Documents

By J. A. Ober

"In 2016, the estimated value of total nonfuel mineral production in the United States was $74.6 billion, a slight increase from the revised total of $73.4 billion in 2015 (Table 1). Increased construction activity spurred increased production of industrial minerals, especially those used in infrastructure and residential construction. Although starting the year relatively low, prices for several metals, especially for some of the precious metals, began to trend upward. Decreased production of most metals produced in the United States, however, contributed to an overall decline in the value of metal production.Several U.S. metal mines and processing facilities were idled or closed permanently in 2016, including iron ore mines in Michigan and Minnesota; three primary aluminum smelters in Indiana, Missouri and Washington; one secondary zinc smelter in North Carolina; a titanium sponge facility in Utah and titanium mineral operations in Virginia. In addition, in May, the weekly average rig count for oil and gas drilling reached its lowest level since the 1940s when that measurement was first recorded. The reduced drilling activity resulted in decreased production of some industrial mineral products used in the drilling sector. Trends in mineral-related sectors of the domestic economy declined or held steady, except in the manufacturing of nonmetallic mineral products and nonferrous metals excluding aluminum, which increased. Overall, mining trended downward as the result of significant declines in coal mining, oil and gas extraction and metal mining (Table 2). Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, which have higher production quantities but are lower-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of construction aggregates are orders of magnitude larger than those for most other mineral commodities thus making direct compar"

Jan 5, 2017

By U. S. Geological Survey Staff

"In 2017, the total estimated value of nonfuel mineral production in the United States increased by 6 percent from 2016 (Table 1). The value of metals produced domestically increased by 12 percent and the value of industrial minerals produced domestically increased by 3 percent. Some metal commodity values (cobalt, magnesium metal and palladium) increased by more than 35 percent in 2017 from 2016 owing to higher prices.Some U.S. metal mines and processing facilities remained idle in 2017, including three primary aluminum smelters in Indiana, Missouri and Washington; a titanium sponge facility in Utah and a byproduct vanadium production facility in Utah. In contrast, new gold mines opened in late 2016 and 2017 in Nevada and South Carolina, respectively, and iron ore mines in Michigan and Minnesota restarted or operated for the full year. In addition, increased oil and natural gas drilling activity led to increased production of some industrial mineral commodities that are used for oil and gas drilling. Production of some industrial minerals, especially those used in infrastructure and residential construction, remained essentially unchanged in 2017, a reflection of the limited growth in construction activity. The production of some metals, including iron and steel, aluminum and other nonferrous metals and nonmetallic mineral products increased. Overall, mining activity trended upward as the result of increases in coal mining, oil and gas extraction and metal mining (Table 2).Discussion of mine production is commonly segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, such as crushed stone or construction sand and gravel, which have higher production quantities but are lower-valued materials. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of natural aggregates are orders of magnitude larger than those for most other mineral commodities, thus making direct comparisons based on weight meaningless (Fig. 1)."

Jan 5, 2018

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016

By G. E. Viens

The electric arc furnace has characteristics which make it attractive for a number of metallurgical applications. Some of these characteristics are: high thermal efficiency, the possibility of attaining very high temperatures, low off-gas volume compared to fuel-fired furnaces, no impurities are introduced by the heat source, and impurities in only minor amounts are introduced by the electrodes. It also has disadvantages, the chief ones being the relatively high cost of electrical energy compared to fossil-fuel energy and the fact that, when oxide ores are smelted using carbon as reductant, the off-gases emitted are rich in carbon monoxide. As in many other pyrometallurgical processes, fumes and dust are emitted from melting or smelting operations. In many installations, some or all of the off-gases are flared, thereby wasting their energy and contributing to atmospheric pollution. During the last eight years, a shaft-electric furnace has been under development at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This project was initiated to try to overcome, or at least minimize, the disadvantages of the electric furnace. Experience on other projects, prior to the beginning of this program, had indicated that preparation of the charge materials, for example by sizing raw ore, sintering concentrates and crushing and sizing the sinter, or agglomerating concentrates into uniform-sized pellets, could make a substantial contribution towards achieving success in arc-furnace smelting projects; This entire

Jan 1, 1971

By L. M. Gochioco

The U.S. coal industry is under-going dramatic changes to meet the challenges of the keenly competitive fuels market. The application of innovative technologies is needed to improve safety and to increase productivity in order to make coal more competitive as a fuel. As more coal companies shift into capital intensive longwall mining, there is a clear need to invest more in exploration before mine plans are made. Coal seam anomalies may create adverse mining conditions. The early detection of these anomalies could make the longwall mining safer and more productive through improved planning. A standard exploratory drilling program can provide only limited geologic information. The seismic reflection technique can be used to detect coal seam anomalies and is effective in reconnaissance surveying. Recent advances in the quality of coal seismic data have increased the success rate of seismic surveying. Therefore, surface seismic surveys, coupled with selective drilling, will come to play an integral role in coal exploration in the 1990s.

Jan 1, 1990

By Jerry G. Rose

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14,000 kPa (2,000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room-and-pillar mines so that a Substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction because of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal-crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the coal-crete pillar system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 1, 1977

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Cat 994 class) as primary loading equipment in open pit iron ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Data were gathered on loader selection rationale; operating and maintenance experience; and production, availability, and cost information. Brief time studies were conducted to indicate machine performance and utilization. The paper summarizes the field data and includes economic comparisons of wheel loaders versus cable shovels in an iron ore application.

Jan 1, 1996

By A. D. Davis

Environmental impacts from acidic mine drainage are growing national concerns that are particularly acute in the headwaters of the Rocky Mountain region. In the Black Hills of South Dakota, approximately one thousand mines are inactive or abandoned, most of them in the headwaters of major drainages. This paper examines the Bear Butte Creek basin, a heavily mineralized watershed with significant historical mining impacts and a surface gold mine permitted in 1997. The watershed loses its surface discharge to swallow holes in the karstic Madison Limestone. The integrity of the aquatic ecosystem was monitored with a suite of site-specific bio-indicators. Stream surveys covered the entire reach of Bear Butte Creek from near its headwaters to the swallow holes in the Madison aquifer. Data from the stream surveys, water-quality sampling, and bio-indicator surveys clearly showed that water-quality impacts are limited mainly to Strawberry Creek and to the area of Bear Butte Creek near and downstream of the town of Galena.

Jan 1, 1999

By B. R. Waples

Sometimes a project is born easy, sometimes a project has a hard time being born. Probably every project can say we had tremendous problems to overcome and they would all be right. This project had all things happen to it. Born easy, a hard time after being born, there were tremendous problems to overcome but here it is, a major copper project, a major operation, and a new source of copper for Mexico and the world market. La caridad is an ore body located in the state of Sonora in northwestern Mexico. It is at an elevation of 1,200 meters above sea level and the nearest major city is Hermosillo, the capital city of Sonora. Hermosillo is located approximately 270 kms (about 168 miles) to the southwest of la caridad. North of la caridad, 130 kms (about 81 miles), is the U.S. border town of Douglas, Arizona, which has a sister city on the Mexican side of the border -Agua Prieta.

Jan 1, 1979

By Corale L. Brierley

Bacteria, algae and fungi react to heavy metals in their environment by immobilizing, mobilizing and/or transforming metals. Microorganisms carry out these changes by (1) precipitating metals outside of the microbial cell, (2) binding and complexing metals to the outside of the microbial cell's protective coating, (3) accumulating metals inside of the microbial cell, or (4) transforming metals by oxidation, reduction, methylation or demethylation. Most of these mechanisms are operative in constructed aerobic and anaerobic wetlands for metal's remediation. Several more advanced biotechnologies for metal's removal from aqueous streams have been introduced, but have not been widely accepted commercially.

Jan 1, 1995

By Dayu Long, Changhong Li, Yu Wang, Juzhou Li, Yongyue Hu

To address the problem of seepage failure that affects the stability of the fine-grained tailings dam, two kinds of prevention and treatment measures were proposed involving composite flocculants and composite curing agents. The orthogonal test was conducted to determine the optimal ratio flocculant (ORF) and the optimal ratio curing agent (ORCG). Then, numerical models were established to evaluate the effects of the prevention and treatment measures on the seepage and stability of the tailings dam. The results show that the mechanical properties and microstructure of the tailings are significantly improved by adding the ORF and ORCG. Furthermore, numerical studies suggest that the addition of the ORF and the ORCG to the tailings improves the factor of safety of the tailings dam, but the addition of the ORCG also increases the height of the phreatic line. It is also speculated that the addition of the ORF can prevent the formation of through failure zone in the tailings dam. Therefore, the optimal measure to prevent seepage failure in the tailings dam is adding an appropriate amount of the ORF, as it reduces the height of the dam’s phreatic line and lowers the risk of seepage failure. The typical area susceptible to seepage failure can be treated by adding the ORCG. However, it is important to ensure adequate drainage of the area and to maintain the phreatic line at a reasonable buried depth.

Mar 4, 2024

By D. J. Lachel, Douglas E. Hansen, Bruce Kennedy

The very high cost of exploration and development for new mines requires that a carefully planned, complete, and technically competent geotechnical evaluation be applied to the ore body and the surrounding rock. The ground conditions must be predetermined sufficiently so that, during the development and exploitation stages, unexpected conditions will be of minor consequence. Ground conditions are a major factor affecting the cost of excavated items such as shafts and inclines. For example, shafts cost less to sink in tight dry ground than in highly pervious ground below the water table, with all other factors being equal. The proper mining methods also is dependent upon the ground conditions. Bad ground for room-and-pillar mining may be ideal for caving methods; whereas, ideal ground for room-and-pillar mining would be extremely difficult for a caving operation. To do a proper engineering design, the parameters of strength, deformability, and permeability must be determined, in addition to the loads that will be applied as a result of the mining activity. The required degree of accuracy for each parameter depends upon the individual case. For example, the strength of massive rock in which openings of small cross-sectional area are to be driven at shallow depths needs to be resolved only within several thousand kilopascals (pounds per square inch). Under such conditions, the rock strength is not likely to be of great economic importance unless the rock is very weak. Large openings at great depths require a much more accurate appraisal of rock strength and deformation characteristics. Ground water conditions are important at any depth. Today, a number of techniques exist for evaluating conditions before opening up the ground for development. These techniques and their applications are described in more detail later in this text. The evaluation of ore body ground conditions should start at an early stage, as soon as the deposit has been proven viable for a mine. Economic geology investigations mainly serve to define the value and limits of the ore deposit. To do this properly, the geology of the site is determined in at least as much detail as is necessary to define the "controls" for the ore body. The ground-condition evaluation must determine the engineering properties of the ore body and the surrounding material. This includes the structural geology as it relates to rock strength; i.e., the frequency, extent, and orientation of discontinuities such as faults, joints, bedding, etc. Ground water conditions also must be determined. It is important that the detailed geology of the site be determined at an early date. Reasonable geotechnical parameters must be established during this time period, so they can be used in mining model studies that include both physical and mathematical models. The ultimate goal bf-the geotechnical evaluation is to predict the ground behavior as the excavations are made and how the ground behavior will affect the safety and economic well-being of the mine. The formulation of a ground-condition evaluation program should be planned carefully to determine the particular geotechnical parameters only in as great a detail as will have a bearing on the mine design. For instance, it is not necessary to make numerous triaxial tests in strong rock when the mining will be conducted within a few meters (feet) of the surface in a regime of gravity loading and an absence of tectonic stresses. Similarly, it is not necessary to invest large amounts of time and effort in the determination of joint strengths if the orientations of the joints are such that the failure could not occur along them. Generally, the determination of ore body ground conditions can be divided into four main steps: 1) The general and structural geology of the site must be determined; this is determined primarily during the economic evaluation. 2) The material behavior characteristics of the deposit and the vicinity must be determined. 3) The ground water hydrology of the deposit and the vicinity must be determined. 4) Miscellaneous ground support considerations must be established. Gross features are defined first, followed by a series of increasingly detailed investigations. Specifically, the geology study should start by utilizing techniques such as remote sensing, topographic map interpretation, geologic mapping, etc. After the gross features, such as major faults, have been delineated, the studies are directed toward defining the more detailed elements of jointing, rock strength, ground water hydrology, and other characteristics. This information is used to formulate an assessment of the strength of the ore body and the surrounding rock. Finally, all of the gathered information is integrated to make an assessment of the rock behavior in relation to the types of openings, the excavation methods, the support requirements, etc., that should be used for the rock conditions that are present. The mine design and the geotechnical assessment should be an iterative process. General conclusions about the rock conditions will dictate a type of mine plan. The specific mine plan then should be modified by specific geotechnical considerations. For example, an initial assessment may conclude that the ore body is strong and that a strong rock unit is present over the ore body. Thus, one definite possibility is to mine the deposit by room-and-pillar methods. However, subsequent investigations may reveal faults through the deposit, requiring relocation of the mine openings so that pillars and other structures are in sound rock. In other words, the final mine plan should be compatible with the geotechnical aspects of the ore body.

Jan 1, 1982

By M. E. Rossi

This paper discusses the use of Conditional Simulation (CS) models to provide mill feed grade profiles for different time periods. The conventional approach of classifying block estimates as ore or waste generally does not adequately represent dilution, lost ore and the anticipated grade control data, including variability of mill feed from the pit and possible stockpiles. The detailed simulation of grade control practices can be done, but at the Pre- or Feasibility stage of the project may be impractical, since drawing dig limits on multiple benches is tedious and time consuming. Using the Feasibility Grade Control (FGC) method as developed by the Centre for Computational Geostatistics (CCG, University of Alberta-Edmonton), the CS models can be processed quickly to establish dilution and lost ore, and predict daily or short-term feed to the mill. The simulated nodes can be aggregated into selective mining units with adequate representation of likely geometries to be recovered from the pit, to mimic anticipated selectivity. An example from a large copper deposit is shown. The study provides an estimated stream of tonnages and grades fed to the plant by mining periods of interest and based on a specific mine design and schedule. The resulting cash flows support the economic and financial analyses of the Feasibility Study; also leads to improving mine schedules; and aids in developing blending schemes if necessary. INTRODUCTION The conventional approach of separating mineralized material into ore or waste categories does not always include a realistic amount of dilution and ore loss. Also, often it does not provide a good estimate of the grade that will be fed to the mill. If the grade control estimates are unbiased, they will over the long run represent the long-term average of grades fed to the mill; but the anticipated variability of mill feed from the pit and stockpile sources may be misrepresented. Some references on traditional grade control implementations can be found in Chunnett (1982); Davis et al. (1989); Srivastava et al. (1992); and Nowak (1992). Alternative methods based on economic variables improved significantly on the purely grade-based control methods, see Douglas et al. (1994). Further developments involved the use of geostatistical conditional simulations (CS) and profit models, which in several cases have been successfully implemented (Aguilar and Rossi, 1996; Rossi, 1997; Deutsch et al., 2000; Norrena and Deutsch, 2002; Neufeld, 2005; Jewbali and Dimitrakopoulos, 2009). But they can be impractical, mostly due to the lack of understanding of the methodology involved; even if semi-automatic dig limit drawing is implemented, there is always a need for is tedious and time consuming checking and corrections, even if using a single profit model derived from the simulated grades.

Jan 1, 2019

By D. J. Beeby

California's Surface Mining and Reclamation Act (SMARA) was passed in 1975 to identify and protect mineral resources in areas of high land use conflict and ensure reclamation of mined lands. Under SMARA, aggregate resource availability is quantified and compared to forecasted demand in specific market regions. Fifteen regions studied thus far cover 51,800 km2 (20,000 sq miles) and contain 45 Gt (50 billion st) of high-quality aggregate resources that have been legally designated as "regionally significant," providing a measure of protection previously unavailable. SMARA reports and state testimony at local hearings have supplied objective information and helped reduce conflict in mine permitting decisions.

Jan 1, 1987

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By M. J. DeMarco

Beginning in late 1985 and continuing through 1987, Bureau of Mines personnel investigated longwall chain pillar and entry design in two-and three-entry gate-road systems at a deep underground coal mine located in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau of Mines hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in roof falls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1988

By Albert R. Rule

Beneficiation studies were made by the Bureau of Mines to develop a process for concentrating phosphate minerals from the altered rock of the Phosphoria Formation. This report describes research on intermediate - and marginal-grade ores from southeast Idaho, The process developed consists of attrition scrubbing and sizing to produce a coarse concentrate; desliming at about 800 mesh (18.5 microns); flotation of the fine sands; roasting of the combined concentrates for removal of organic carbon and combined water; and leaching with SO2 for removal of magnesium and nonapatitic calcite. Results of continuous tests on three different ore types showed that approximately 80 percent of the available phosphate can be recovered at a grade suitable for phosphoric acid production. While leaching with SO2 is not necessary for all ore types, it is an important step in purifying concentrates containing excessive magnesium.

Jan 1, 1966

By James L. Hendrix

This paper is intended to give the reader an update on the work being done at the Mackay School of Mines about the fate of cyanide on precious metals mill tailings waste. During the last two years several tailings impoundments have been sampled and analyzed for total and free cyanides. From our sampling program we are beginning to learn valuable information concerning the fate of cyanides in precious metals mill wastes. Included in this paper is a detailed description of our sampling and analytical techniques. Also, some of the data obtained from five sites are given.

Jan 1, 1986

By M. S. Celik

Unlike most other minerals, electrokinetic measurements of calcium montmodonite (a clay mineral) and u1exite (a boron mineral) exhibit an unusual behavior. While the addition of monovalent salts such as NaCI and KCI is expected to compress the electrical double layer with a resultant less absolute charge, an opposite trend is observed. A set of systematic experiments with monovalent and multivalent ions has been carried out to understand the mechanism of this phenomenon Examination of the results reveals that the behavior of montmorillonite is dictated by the exchangeable divalent cations at the edges which undergo an exchange process with monovalent cations resulting in the reduction of positive charges. The solubility of ulexite, on the other hand, is found to decrease with increasing monovalent cation concentration leading to again an increase in the absolute negative charge.

Jan 1, 1996

Anomalous geologic or stress conditions ahead of the longwall face can cause great harm to both the individual miner and the mining operation as a whole. The U.S. Bureau of Mines has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of a field effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure, and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration, likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with laboratory measurements.

Jan 1, 1995