Search Documents

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"One of the most pervasive diseases in the mining industry is noise-induced hearing loss. The exposure of miners to noise levels above the permissible exposure level results in hearing loss in approximately 80% of coal miners by retirement age. In this context, the U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for longwall mining systems, which are used to extract half of the national underground coal production.From field measurements, previous research determined that the dominant sound-radiating components at the shearer of a longwall system are the two cutting drums used to remove coal. Due to the dimensions and complexity of longwall mining systems, the NIOSH project developed a validated finite element model of the cutting drum to use in predicting the sound radiated by the drum due to the excitation forces experienced in underground operations. This same model will be used to develop engineering noise controls for the drum. The excitation forces arise from the interaction of the cutting bits and the coal and are transmitted to the cutting drum through the bit holders. Due to the adverse conditions at the face, and a lack of instrumentation approved for underground use, the operational coal cutting forces have not been assessed before. To this end, NIOSH, in collaboration with Michigan Technological University, developed a self-contained, intrinsically safe instrumented bit to measure these forces.This paper describes the development of the instrumented bit and the measuring of operational coal cutting forces at three working coal mines. The measurements revealed that the forces have a flat spectrum, representative of the impact nature of these forces, up to around 100 Hz. Above this cutoff frequency, the force magnitude decreases at a rate proportional to the inverse of frequency squared."

Jan 1, 2014

By R. E. Hamilton

It is more than ten years since the first fully automated process using a computer started operation. Computer control has become common in a number of process industries, yet in spite of the tremendous incentives which ere present, there are only a few computer installations in the mining industry and none of these has announced successful control of a process. Recognizing that one of the reasons for this slow progress is the lack of adequate mathematical models of the various processes involved, the author's company started a project in the summer of 1966 to develop such models. It was early recognized that the existence of a major disturbance input, in the form of the mineral composition of the feed prevents most flotation plants from attaining a steady state condition. This makes the custom¬ary method of developing correlations from steady state plant data inapplicable and requires a more fundamental approach.

Jan 1, 1968

By L. Yuan, J. H. Rowland, R. A. Thomas, D. Bahrami

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time. INTRODUCTION Underground miners are at risk of overexposure to toxic gases from various sources. Production blasting operations using explosives in underground mines are a source of multiple toxic gases that could be harmful and even fatal to humans if prolonged exposure occurs beyond the safe limits. According to Code of Federal Regulations, Title 30, Part 57.5002 [1], metal and nonmetal mine operators must conduct gas, mist, and fume measurements as frequently as necessary to determine the adequacy of control measures to protect miners from overexposure to harmful gases. MSHA will inspect mine operators’ activities to verify the evidence of such measurements [2,3]. Continuous gas monitoring in the return air is an effective way to make sure that toxic gas concentrations at the working areas are kept below the regulatory limits before the return of miners. Toxic gases can enter the mine atmosphere from different operations, such as welding, combustion, and blasting. The main gases produced from blasting are carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), and nitrogen dioxide (NO2). Other gases are produced in small amounts and, therefore, were not considered for this study. Related regulatory and recommended exposure limits of CO, NO, and NO2 gases are summarized in Table 1 [4].

Jan 1, 2019

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, B. D. Ganesh Shetty, M. RAJU

The production of high strength iron ore sinter for blast furnace iron making unit was developed by optimizing the granulometry of less than − 0.150 mm fines in sinter base mix which consists of iron ore fines (− 10 mm size with 0.150 mm: 41%), beneficiation plant jig concentrate, i.e., washed ore (− 3 + 0.150 mm size with − 0.150 mm 3 to 9%), beneficiation plant concentrate (− 0.150 mm size 97%), limestone, dolomite, coke breeze, lime, sinter return fines, direct reduced iron (DRI plant) fines, and micropellets produced from steel plant waste. The sintering process consists of preparation of base mix, mixing, and production of nodules using mixing and nodulizing drum by maintaining the optimum moisture, transferring of nodules to the sintering machine, and firing of sinter by applying optimum suction pressure. To optimize the < 0.150 mm fines in sinter base mix, the − 10-mm size iron ore fines was replaced with washed ore. The size analysis, granulation index (G index), and optimization of moisture w.r.t. sinter bed permeability were carried out by varying the washed ore addition from 0 to 55% in sinter base mix to vary the − 0.150 mm fine size. With decrease in washed ore addition from 55 to 0% in sinter base mix the finer fraction, i.e., − 0.150 mm in sinter base mix increased from 9.4 to 26.7%. Granulation (G) index increased from 1.46 to 3.10, sinter bed permeability increased from 33 to 53 Japanese Permeability Unit (JPU), and balling index increased from 1.4 to 3.0. With increase in − 0.150 mm fines in the sinter base mix from 9.4 to 26.7%, the sinter tumbler index (T.I) increased and sinter reduction degradation index (RDI) decreased. Increase in sinter strength and decrease in sinter RDI was due to increase in formation of Silico ferrite of calcium and aluminium (SFCA) phase and decrease in pore phase. The SFCA is the main bonding phase in iron ore sinter, and it provides strength to sinter. Sinter base mix with − 0.150 mm fines 18.9% (washed ore addition 25%) achieved desired sinter properties with moisture 8.0%, G index 2.44, balling index 2.3, and sinter bed permeability > 45JPU. Decreased the sinter properties with washed ore addition in sinter base mix beyond 25% due to decrease in − 0.150 mm fines in sinter base mix. Further, to improve the sinter properties with washed ore 30 to 45%, 3 to 10% beneficiation plant concentrate, i.e., − 0.150 mm fines was added to maintain the 18.9% of − 0.150 mm fines in sinter base mix. From the laboratory sintering studies, it was found that minimum 18.9% (range from 18.9 to 26.7%) − 0.150 mm fines should be maintained in the sinter base mix to achieve desired sinter properties.

Oct 16, 2021

By J. R. Heberger

"“Safety Pays in Mining” web application developed by the U.S. National Institute for Occupational Safety and Health Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of more than 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, the app will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items, such as services or equipment, on which companies could spend the savings that result from the prevention of injuries. This paper reviews the app by discussing its development, how it is used to show the true costs of mining injuries, and how mines can benefit from using it.IntroductionInjuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker or divert administrative resources in the wake of an injury. “Safety Pays in Mining” is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits.The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies do not usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, for example, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide that just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of the potential impact on their company’s financial health."

Dec 1, 2018

By Hugo E. Camargo, Amanda S. Azman, Brian Kim

Repeated noise exposure and occupational hearing loss are common health problems across industries and especially within the mining industry. Large mechanized processes, blasting, grinding, drilling, and work that is often in close quarters put many miners at an increased risk of noise overexposure. In stone, sand, and gravel mining, noise is generated from a variety of sources, depending on the type of ore being mined as well as the final consumer product provided by that mine. Depending on the source of noise generation, different strategies to reduce and avoid that noise should be implemented. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the noise profile at three operational surface stone, sand, and gravel mines. A-weighted sound level meter data as well as phase array beamforming data were collected throughout the mines in areas with high noise exposure or high personnel foot or vehicle traffic. Sound level meter data collected on a grid pattern was used to develop sound profiles of the working areas. These sound contour maps as well as phase array beamforming plots were provided to the mines as well as guidance to modify work areas or personnel traffic to reduce noise exposure.

Jan 6, 2022

By Osvaldo A. Bascur

Most mining and metallurgical plants have developed predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, oil and lube analysis for critical equipment. Process control strategies have also been installed in several metallurgical sites. These control strategies require instrumentation maintenance from local personnel. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is a must for global plant optimization. Specialized performance control monitoring algorithms are required to justify their existence and contribution to the bottom line. Emerging technologies are combining these techniques into a single total plant system. Tools are required to assist in troubleshooting and adapting these process control instruments and strategies. The key is the plant equipment and process control availability and utilization rather than just maintenance.

Jan 1, 1997

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"Una de las enfermedades más extendidas en la industria minera es la pérdida de audición inducida por el ruido. La exposición de los mineros a niveles de ruido superiores a los niveles de exposición permisibles resulta en la pérdida de audición de aproximadamente el 80% de los mineros del carbón a la edad de jubilarse. En este contexto, el Instituto Nacional para la Seguridad y Salud Ocupacional (NIOSH, por sus siglas en inglés) está realizando investigaciones para desarrollar controles de ruido aplicados a los sistemas de minado de tajeos largos. Este método de minado es usado para extraer la mitad de la producción nacional de carbón subterránea. A partir de las mediciones en campo, se determinó en investigaciones anteriores que los componentes dominantes que generan sonido en el cizallador de un sistema de tajeos largos son los dos tambores de corte utilizados para extraer el carbón. Debido a las dimensiones y complejidad de los sistemas de minado de tajeos largos, el proyecto NIOSH desarrolló un modelo de elementos finitos validado del tambor de corte para utilizarlo en la predicción del sonido generado por este debido a las fuerzas de excitación experimentadas en las operaciones subterráneas. Este mismo modelo se utilizará para desarrollar controles de ingeniería para el ruido del tambor. Las fuerzas de excitación surgen de la interacción de la broca de corte y el carbón, y se transmiten al tambor de corte a través de los sujetadores de brocas. Debido a las condiciones adversas en el frente y la falta de instrumentación aprobada para uso subterráneo, las fuerzas operativas de corte de carbón no han sido evaluadas anteriormente. Para este fin, NIOSH, en colaboración con la Universidad Tecnológica de Michigan, desarrolló una broca instrumentada autónoma con seguridad intrínseca para medir estas fuerzas. Este artículo describe el desarrollo de la broca instrumentada y la medición de las fuerzas operativas de corte de carbón en tres minas. Las mediciones revelaron que las fuerzas tienen un espectro plano, algo característico de la naturaleza del impacto de estas fuerzas, hasta alrededor de 100 Hz. Por encima de esta frecuencia "cutoff", la magnitud de la fuerza disminuye a una razón proporcional al cuadrado de la inversa de la frecuencia."

Jan 1, 2014

By J. H. Kempton, D. Atkins

Predictions of delayed environmental impacts from mining—degradation that won’t begin for hundreds of years, but will then continue for thousands—present new permitting challenges. Examples include evaporative concentration in pit lakes, which can eventually cause metals concentrations to exceed human and wildlife toxicity standards, and delayed degradation of groundwater by slow moisture percolation through acid-generating tailings and waste rock. Given the time-value of money, the present worth of such delayed impacts is insignificant, yet they are unacceptable undercurrent laws and cultural values. Long-term financial set-asides offer a possible solution, first funding infrequent, long-term monitoring, followed by more expensive mitigation when the set-aside has matured.

Jan 1, 2000

By Harry E. LeGrand

The purpose of this paper is to outline briefly some basic principles of ground-water hydrology that have application in mine hydrology and to suggest that an understanding of these principles can help to forestall problems that are internal as regards mining operations and external as regards damage or harm to surrounding areas. The development of a mine below the water table pleads for accurate values to answers of hydrologic problems. Such internal problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required mining or milling use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by homogeneous rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where rocks are not homogeneous. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground-water occurrence and movement should be helpful to mine operators. Mining operations that extend below the water table disturb the natural hydrologic regimen. Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine, The behavior of the cone of depression, as it tends to deepen and to increase in areal extent when the mine is deepened, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised. The geologic and hydrologic settings of mines range greatly so that a simple standard procedure for dealing with problems

Jan 1, 1972

By P. Bissert, M. Klein, L. Yan, D. Yantek, R. Matetic

"U.S. Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hours. One of the main concerns with the use of mobile RAs is heat and humidity buildup inside the RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in an occupied RA not exceed 95 °F. To investigate this, the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4 °C (17 °F) and the relative humidity approached 94 percent at the end of a 96-hour test. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the volume-weighted average air temperature inside the RA tent at the end of 96 hours to within 0.06 °C (0.1 °F) of the average measured air temperature. IntroductionIf an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter a refuge alternative (RA) for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration, and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke or even death."

Sep 1, 2016

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By Yun-tao Xin, Yu Yi, Kang Yan, Gang Li, Xiao-dong Lv

This study investigated the selective removal of arsenic from high-arsenic dust in alkaline systems and the effects of different leaching conditions. The results indicated that the liquid–solid ratio, NaOH concentration, and sulfur dosage had a significant influence on the process. The leaching efficiency of arsenic reached 99.57%, while that of lead was as low as 0.03% under appropriate conditions. In particular, the addition of sulfur can effectively promote the leaching of arsenic and reduce the dissolution of lead in the solutions. An artificial neural network was used to model the leaching process. It consisted of a back-propagation artificial neural network model with a “6–10–2” structure that could effectively simulate and predict the value with more than 99% accuracy. Based on the difference in weights of the different parameters in the neural network model, the relative importance of the parameters related to arsenic and lead leaching efficiency was obtained, which followed the order of NaOH concentration, liquid–solid ratio, sulfur dosage, temperature, time, and stirring speed.

Jul 29, 2021

By Alan A. Campoli

The US Bureau of Mines (USBM) conducted research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments. The goal is to minimize the over and under design of mine roof support, resulting in more productive and safer mines. To obtain the necessary data on roof behavior and support performance, USBM conducted several field studies. Each study covers roof geology, stress regime, ground reaction, support interaction and mining environment. A consistent experimental design is being used. This includes measurements of roof bolt loads and roof movements. So far, 10 studies have been conducted in several geologic settings.

Jan 1, 1996

By Minerals and Materials Analysis Section

During 1996, US mines produced 319 t (10.26 million or) of gold metal valued at $4 billion. At yearend, mine reserves were estimated to be 4.7 kt (151 million oz) of gold metal. Almost all of the production was from western states. Nevada accounted for about 68% of national production. Information for this article was obtained through annual reports of mining companies, US Geological Survey (USGS) databases and other public sources. Table 1 shows production and reserves by mine. It divides the mines into two categories. These are producing mines whose primary product is gold, and producing mines for which gold is a byproduct or coproduct. The mines listed in Table 1 accounted for more than 98% of US gold production during 1996. Except the Daisy Mine, the table does not include mines that produced less than 31 kg/a (1,000 oz/year). The Daisy Mine started production in December of 1996. Nor does it contain mines whose byproduct concentrate is

Jan 1, 1997

By Hans Adden, Anne Lehan, Markus Thewes

"1. INTRODUCTION AND MOTIVATION Traditionally design processes are focussed at creating new tunnels for lowest building cost. But the trend towards sustainable constructions in tunnelling has greatly increased in recent years. A critical subtask of this approach is to realize the potential for optimizing and reducing the life-cycle costs (LCC) of tunnels and their components. To evaluate underground infrastructure projects from an economic point of view is therefore a highly topical subject of public authorities as well as private companies participating in Public Private Partnerships (PPP) projects. Nowadays, in the case of public works contracts, the contracting authorities shall draw up rules not only for the design but also for life-cycle costing. Within the scope of the decision-making process of building a new tunnel, planning the maintenance activities or the refurbishment of a tunnel in operation, the decision-makers need detailed knowledge about the current and future financial conditions of the planned projects and selected sub-measures. But in practice, the initial costs still represent the primary decision criterion in the planning phase, whereas the subsequent or follow-up costs, respectively, are only estimated roughly. Although tunnels are the key components and the most costly parts of the transport infrastructure, only a small number of scientific papers deal explicitly with the calculation of life-cycle costs for underground infrastructure. And in these cases, most authors use as the starting point only the basic form of the Net Present Value method which is known as the frequently applied life-cycle costing technique in building construction. The present study explains the strategic concept of life-cycle costing and its fundamental instruments for operational implementation. It shows the necessity to take into consideration that there are fundamental methodical problems when the life-cycle concept is transposed without modifications from building construction to civil engineering. The paper will discuss in detail some selected associated problems with the net present value method. On the basis of operational and safety related tunnel equipment it is shown, what impact this may have on principle determining the LCC of tunnels. Selected best-practices of maintenance planning for tunnels undertaken by the German Ministry of Transport fill the theoretical approach of the concept with life and give a practical orientation. In particular government authorities but also construction companies are interested parties in modern cost management considerations. The reason for this development is the replacement of aged excisting structures and the advancement of technical standards. The increase in the total numbers of tunnels (Fig. 1) as well as the need for future re-investments in existing tunnels show the overall economic impact and justify the change towards the life-cycle perspective."

Jan 1, 2016

By J. de Bakker

It hardly needs to be repeated that if coal is to continue as America’s premier source of cheap energy, it is absolutely necessary that the carbon dioxide from its combustion somehow be sequestered. A promising method proposed to accomplish this is the “indirect” carbonation of serpentine in a concentrated magnesium chloride brine. Indirect carbonation could be also applied to precipitate magnesium in lateritic nickel processing: this would not only solve magnesium-control problems in laterite hydrometallurgy, but also reduce its energy requirements and create CO2-sequestration credits. Fifty-five percent of the electricity generated in the United States comes from coal-fired power plants, and American coal reserves can last over 500 years at 1990-level consumption1. Coal is therefore both abundant and cheap: it could (and in fact probably will) continue to be an affordable source of energy, both for producing electricity and as a feedstock for liquid hydrocarbon production by Fischer-Tropsch reactions. As a result, it is important to find a workable method of permanently sequestering CO2.

Jan 1, 2007

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs.Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By B. Birol, M. N. Saridede

"Slag density is a significant factor in determining the process efficiency of the electroslag remelting (ESR) process, where calcium fluoride (CaF2)-based slag is formed synthetically to refine metal ingots. Although there are some former studies investigating the density of CaF2-containing slags, the prediction models focusing on them are applicable only to some specific systems. The present study aims to build a model to predict density for a wide range of CaF2-containing ESR slags. To investigate density for various slag compositions, CaF2-Al2O3-based and CaF2-Al2O3-CaO-based slag compositions were prepared. Additionally, some minor constituents like FeO, MgO and MnO were added to a 5:3:2 CaF2-Al2O3-CaO slag in order to investigate the effects of these constituents on the slag. The volumes of the prepared slags were measured in a tube furnace at 1450-1550 °C using the sessile drop technique, and their densities were calculated. The results showed that for the slags, density is related to optical basicity, and therefore a prediction model based on an Arrhenius equation was built. The model was tested with data from literature, and its limitations and validity are discussed.IntroductionThe electroslag remelting (ESR) process is a refining method in which a metal ingot is remelted under a synthetic slag. These synthetic ESR slags are mainly composed of calcium fluoride (CaF2), calcium oxide (CaO) and aluminum oxide (Al2O3). Other constituents like iron oxide (FeO), magnesium oxide (MgO), manganese oxide (MnO) and chromium oxide (Cr2O3) are added to this system in relatively low amounts, according to the type of steel ingot to be refined. The prediction of slag properties, such as electrical conductivity, viscosity and density, is crucial for the selection of the synthetic slag in order to obtain the required process parameters, like temperature, the passing time of the molten metal droplet through the slag, and metal-slag separation (Akbari, Reitz and Friedrich, 2009; Hara and Ogino, 1981; Mattar, El-Faramawy and Fathy, 2002; Mehrabi, Rahimipour and Shokuhfar, 2005; Presoly, Korp and Schneider, 2008).As slag density affects metal-slag separation in the ESR process, predicting the density of an ESR slag is important for appropriate refining and improved product quality. Although there are many studies investigating the density of slags (Akbari, Reitz and Friedrich, 2009; Aune, Hayashi and Sridhar, 2005; Hara and Ogino, 1981; Matsushita, 2011; Mills and Keene, 1987, 1981; Seetharaman et al., 2013; Shu, 2007; Shu and Chou, 2013; Sikora and Zielinski, 1974; Xu et al., 2012; Zhang and Chou, 2010), the prediction models built are generally valid for oxide-containing slags (Aune, Hayashi and Sridhar, 2005; Bottinga and Weill, 1970; Mills and Keene, 1987; Seetharaman et al., 2013; Shu, 2007; Xu et al., 2012; Zhang and Chou, 2010). These models were built on either the molar volumes of the constituents (Bottinga and Weill, 1970; Mills and Keene, 1987) or the thermodynamically calculated enthalpy or free energy of mixing, which can be applied to a system containing constituents sharing an ion, such as an O- ion for oxide systems (Aune, Hayashi and Sridhar, 2005; Hillert, 1980; Persson et al., 2007). Some recent studies modeled the density of some oxide slags on their optical basicity (Shu, 2007; Shu and Chou, 2013; Xu et al., 2012; Zhang and Chou, 2010)."

Jan 1, 2016