Search Documents

By E. F. Schnitzer, S. R. Mamoyac, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By D. Brady

The need for onsite gas monitoring during, or following, a major incident at an underground coal mine has long been recognised. Recommendations from inquiries following Queensland mine disasters have included ?qualified persons and equipment for rapid analysis of gas samples be available in times of emergency? and that ?this may be accomplished by either mobile laboratories or laboratories established in each mining locality.? Following the Moura No. 2 disaster, the Queensland Government allocated funds to Simtars for a mobile laboratory to respond should such a disaster occur again in the future. This vehicle was commissioned in 1997 and has been used at many mine sites under a wide range of scenarios. Simtars, armed with over ten years of operational experience with this mobile laboratory, has taken an active role in the design and construction of a modernised replacement unit. With a twenty point tube bundle system and ultrafast gas chromatograph the result is, arguably, the best equipped mobile gas analysis laboratory for mine emergency response in the world. This paper outlines the features of the new laboratory, its capabilities and the philosophy behind the design and inclusions.

Jan 1, 2012

By Z. Hyder, M. D. Cleason

"INTRODUCTION Mine Ventilation has come a long way over the years. The main purpose of mine ventilation is to keep conditions in the mine safe for the worker so that the mine will be productive and profitable. Technological developments to the mine ventilation system itself and the development of mining techniques have helped improve the safety and productivity of the miners and the mine. Most of the developments to mine ventilation and to safety devices came as the result of serious mining disasters. Another effect of those mining disasters, especially in the late 19th century and after, was legislation to set specific safety standards for mines, especially in the underground coal mines. This paper will focus on the connection between mines disasters and the mine safety legislations promulgated because of those disasters. A BRIEF HISTORY OF MINE SAFETY LEGISLATION Mine legislation has a long history in the U.S. dating back well in the 1800’s. However, mine safety legislation is considerably newer. In 1891, the U.S. Congress passed the very first version of mine safety legislations setting up minimum safety standards. By today’s standards, the 1891 legislation was incredibly basic (7). It took a series of horrific mining disasters for Congress to take action a second time. In 1910, Congress established the Bureau of mines. The role of Bureau developed and changed over next 60 years. In 1995, Congress voted to disband it (27). Initially the Bureau was only charged with investigating and coming up with ways to reduce accidents in coal mines. It was not until 1941, when Congress formally allowed Bureau of Mines’ Inspectors into the mines. In 1947, the Congress enacted and adopted a set of federal safety regulations for the inspectors to follow (1). Finally, in 1952 Congress granted the Bureau of Mines the authority to inspect the mines and to issue citations and/or orders of withdrawals. This act was known as the 1952 Coal Act and the penalties were limited to civil penalties. It would take a couple more iterations of mine safety legislation for monetary and criminal penalties to be introduced (10). Up until 1966, mine safety legislation was directed primarily at underground coal mines and surface coal mines. Congress passed the Federal Metal and Nonmetallic Mine Safety Act of 1966, thus providing a set of standards for all mines to follow (1). The 1952 Coal Act was amended again to be the Federal Coal Mine Health and Safety Act of 1969. This amendment was the beginning of modern mine safety legislation (13). In 1973, Congress created what can be considered the first ‘version’ of the modern day MSHA (Mine Safety and Health Administration). The initial version was the Mining Enforcement and Safety Administrations or MESA. Congress created MESA to act as the enforcement agency, relieving the Bureau of Mines of that responsibility so they could focus on their initial purpose, the development of countries natural resources (14). As mining industry grew, mine safety and health became a greater concern and priority. More efforts were put in legislating the industry. The Federal Mine Safety and Health Act of 1977 provided the platform for today’s mine safety and health legislation. Under the Federal Mine Safety and Health Act of 1977, also known as the Mine Act, MSHA came into being (1)."

Jan 1, 2016

By A. D. S. Gillies

The use of refuge chambers for use in handling underground emergencies is an issue of topical relevance within the US mining industry. Chamber design is of importance to meet some new safety requirements of US federal and some state government mine regulations. A review has been undertaken of a steel mine refuge chamber design to predict what will be internal temperature within the chamber over an extended period with miners present? The design has been examined for the situation when the chamber is sited in still mine air. Spreadsheets have been developed to allow various design assumptions to be tested. The evaluation has been undertaken using thermodynamic heat transfer models with some assumptions specified to produce a model of appropriate simplicity but with adequate degree of accuracy. Under normal still air conditions it can be seen that internal chamber conditions rise quickly to often arduous conditions. There will always be quite a few assumptions necessary in complex heat transfer process evaluations. Some important refuge chamber design parameters are: ? External surface area of the chamber, its wall thickness and construction. ? Metabolic heat generated and number of persons making use of the chamber. ? The temperature of the external mine atmosphere to the chamber over the year and the influence of geothermal gradient on temperature at depth. ? The maximum internal chamber Apparent Temperature considered safe. ? The distance inside the underground mine and adjacent ventilation conditions.

Jan 1, 2012

By E. F. Schnitzer, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007

By G. Lawrence, R. Pieters, A. Leung, T. Pedersen

The Main Zone and Waterline pit lakes at the Equity Silver Mine near Houston, BC (Canada) are the sites of a new 3-yr research program with three primary goals: 1) understanding controls on metal concentrations in the lakes; 2) using mesocosms to test a variety of remediation strategies; and 3) verifying and improving an existing coupled physical-geochemical model with the goal of improving predictions of pit lake water quality. Initial data from two summer surveys in the Main Zone pit lake reveal elevated dissolved metal concentrations (e.g. [Zn] as high as 800 µg/L) present in a two-meter-deep mixed layer, and elevated particulate metal concentrations towards the bottom of the water column. Hydroxide sludge, a byproduct of ARD treatment, is being discharged to the surface waters of the Main Zone pit lake. The sludge sinks rapidly to the lake bottom, leading to deep waters with elevated levels of dissolved O2 and total metals. By contrast, the deep waters of the proximal Waterline pit lake are mildly reducing, manifested by depletion of O2 and elevated levels of dissolved Fe. These reducing conditions have led to elevated levels of As (up to 1500 µg/L) in Waterline pit deep waters. The contrasting behavior of these two pit lakes, as well as the processes controlling metal concentrations in the lakes, will be discussed.

Jan 1, 2002

By S. J. Schatzel

In order to better understand the effects of longwall mining on the methane reservoir overlying the panel, the National Institute for Occupational Safety and Health/Pittsburgh Research Laboratory (NIOSH/PRL) designed and implemented a vertical borehole monitoring experiment (BME) on an active longwall panel. The mine operates in the Pittsburgh Coalbed in Greene County, Pennsylvania. The BME site was located away from either end of the panel to avoid mechanical influences caused by the draping of overburden in this region and was positioned at the same distance from the tailgate gateroad as the mine?s gob gas venthole sites. The borehole drilling depths and monitoring intervals were chosen to address a different stratigraphic zone in each of the three planned holes. The monitoring boreholes were positioned perpendicular to face advance using a close spacing pattern of about 15 m (50 ft) between collars. Boreholes were instrumented downhole and on the surface for various measurements. It was observed from the field data that the gob gas venthole fracture network formed 24-46 m (80-150 ft) ahead of the mining face. Overburden permeability?s within the same test zones increased 100 to 500 times following undermining. The borehole test interval within the fractured rock responded to overburden gas pressure while the test interval in the caved zone responded to mine ventilation conditions. Eight months after the boreholes were undermined, slug testing indicated permeabilities had increased further in the fractured rock zone. Measurements of surface movement indicate that the permeability development observed in the boreholes is a product of vertical subsidence without lateral movement within the tensional rock mechanics zone on a supercritical longwall panel. Results from this study suggest that maximum permeability in the longwall panel overburden is achieved 58 to 190 m (190 to 620 ft) behind the longwall following maximum compaction of the overburden.

Jan 1, 2009

By William R. Yernberg

The Fifth International Heavy Minerals Conference (HMC) was held Oct. 16-19, 2005, at the Marriott Sawgrass Resort in Ponte Vedra, FL. With SME as sponsor, the 2005 conference marked the first time that the HMC was held in North America. The conference is held every two years and provides an important forum for professionals in the heavy minerals and related industries to meet and discuss issues related to heavy mineral exploration, mining, processing and marketing. Previous locations included Australia and South Africa. The conference consisted of technical presentations, field trips to heavy mineral operations, a trade show and social activities. It was appropriate that Ponte Vedra was selected as the location for the conference. Ponte Vedra, located on the Atlantic Coast 17 km (10 miles) southeast of Jacksonville, FL, is the birthplace of heavy minerals mining in North America. Ponte Vedra beaches were mined from 1916 to 1929 in what was then called Mineral City. Though Ponte Vedra is now a golf and beach resort, there are still four heavy mineral mines operating within an hour’s drive. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site.

Jan 1, 2006

By D. R. Gagnon

Mining companies are continually looking for product-ivity and efficiency improvements with their equipment to reduce operating costs. This paper will review the results of a productivity analysis conducted at the Luscar Ltd. Boundary Dam and Bienfait mines near Estevan, Saskatchewan using a Computer-Aided Earthmoving System (CAES) installed on a track-type dozer. The CAES TTT system is a Global Positioning System that provides the operator with constant survey guidance. The study includes a productivity comparison between two similar test sites, one with the aid of the CAES system and the other, without. The CAES TTT system shows a productivity improvement of between 20 and 35% in the reclamation slope leveling application. Even with the CAES TTT system deactivated, some of the advanced features of the system were used to: retain terrain data for volume calculations; track the equipment position; and, accurately record and separate idle time from working time.

Jan 1, 2002

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

By H. Lyn Bourne

This is the ninth annual tabulation of royalty information. Again this year, some of the older information has been deleted to make room for more than 30 new entries. Several articles and publications crossed the author's desk this past year that relate to mineral valuation and mineral royalty. Tom Loucks presented a paper, "The Valuation of Hard Rock Mineral Property," at the Rocky Mountain Mineral Law Foundation in Santa Fe, NM in July, 1990. His paper gives an indepth explanation of the definitions and concepts related to mineral valuation. It includes descriptions of numerous legal cases that have dealt with mineral valuation and proper reference is given for each case. Loucks works for the Denver Mining Finance Co. Gold royalties generally range from 5% to 7%, net smelter return. However, Severn Brown sent information that shows a much wider variation. Echo Bay Mines reported in its 1989 annual report royalties that range from 1.5 % to 30% for gold from various gold properties. Brown also sent a copy of an article that appeared in the Dec. 27, 1982, issue of Fortune magazine. This issue carried an article by Walter Guzzardi, Jr. "The Huge Find in Roy Ash's Backyard." The article gives the history of Newmont's leasing in Nevada on property that became the Carlin, Bootstrap and Blue Star Mines. The article states that the initial royalty was 10% that escalated to more than 16%. Another property, the site of Gold Quarry, provides an 18% royalty to the same own¬ers. The article makes interesting reading for those interested in mining history.

Jan 1, 1991

By Anna Sukhanova, Svetlana Babaeva, Sergey Andreev, Victor Beltenev

"The Zenith-Victoria /1/ and Jubileynoye /2/ hydrothermal fields have symmetrical structural position on the Mid Atlantic Ridge (Fig. 1). In order to compare the evolution of hydrothermal systems, we conducted mineralogical and geochemical studies of SMS from both sites.Radiochemical and geochemical investigations of massive sulfides of the Zenith-Victoria field distinguishes three major stages of evolution: initial, interim and final represented by Fe-S, Cu-Fe and Zn-Fe types of SMS respectively /3/. In this talk, we describe the results of geochemical analysis of massive sulfides from the Zenith-Victoria field. Geochemical varieties of SMS are considered to be indicators of the evolutionary stages of the hydrothermal system."

Sep 1, 2014

By W. Rogers

Blast-induced rock mass displacement can have a significant impact on ore loss & dilution. The mischaracterisation of the grade boundaries both prior to, as well as a result of blasting can lead to significant financial losses on account of ore loss and dilution. Ore dilution occurs when waste material is miscategorised as ore and sent for processing or stockpiling, diluting the run of mine head grade and recovery. Ore loss takes place when valuable mineral is miscategorised as waste and sent to the waste dumps, thus never being processed and recovered. Extensive research has been conducted at the University of Queensland over the last fifteen years to understand the impact of blast movement on ore loss and dilution. Recent outcomes of this research have developed innovative tools and techniques to measure and model blast movement. These techniques have been implemented at Ahafo gold mine in Ghana to understand blast movement dynamics and to implement solutions to reduce blast-induced ore loss and dilution. These solutions are validated through controlled trials and have been incorporated into site standard operating procedures to sustain the benefits.

Jan 1, 2012

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By A. Yu. Lein, V. V. Maslennikov, S. P. Maslennikova, I. Y. u. Melekestseva, Yu. A. Bogdanov

Tellurium is a high-tech and also toxic element. This element shows sufficient contents in Fe-Mn crusts and nodules in the modern ocean to be involved in future industrial processes [Hein et al., 2003]. Tellurium minerals and contents are not well recorded in modern and ancient black smoker systems. Tellurides are rarely found in sulfides from the modern oceans [Iizasa et al. 1992; Maslennikov et al., 2010]. The previous common opinion that tellurium is scarce in active seafloor hydrothermal systems can be revised due to the recent discovery of abundant tellurides in chimneys from Brothers Volcano vent site [Berkenbosch et al., 2012]. We found abundant tellurobismuthite, hessite, and native tellurium in chimneys from Su Su Knoll vents sites (West Pacific). So, tellurides can be found in some chimneys but absent in others. The causes of this are poorly understood. These conflicting data create numerous questions and require an explanation. The problem can be resolved by research at different scales including analysis of relevant genetic features of host sequences, systematic textural and paragenetic studies of different types of chimneys, and their rare mineral assemblages. Paragenetic models, compositional analyses and ranges of tellurium-bearing minerals and the physicochemical interpretation of chimney diversity in different types of VMS deposits are the main subjects of our research. The data on tellurides in chimneys from ancient VMS deposits should also be useful to resolve this problem.

Sep 1, 2014

By S. G. Mougiakakou

A computerized system (SCAPEVIEWER) based on landscape indices and artificial intelligence techniques is proposed in order to classify landscape images into various categories according to the quality of the pictured scenery. Photographs (totally 108) from various landscapes have been clustered, from seven experts in accordance to the mean estimation of landscape quality, into distinctive (C1), typical or common (C2), and indistinctive (C3). For each of the landscape photographs, ten (10) environmental and operational indices have been selected and determined, corresponding to visibility (V), naturalness (N), relief (R), flora quantity (FC), flora quality (F), water (W), skyline (SL), visual entities (G), season (S), and viewer position (P). These landscape indices are fed to a classifier. The classifier is a feed forward Neural Network (NN) trained by a novel hybrid method combining genetic algorithms and the back-propagation algorithm with adaptive learning rate and momentum. A total classification rate of 93.5% has been achieved, using only 8 input neurons. The discarded input neurons correspond to the indices S, and P. The pilot system SCAPEVIEVER has shown the feasibility of landscape photograph classification into three categories (C1, C2, and C3) according to the landscape quality, selecting simultaneously the most robust indices, by means of a computerized system combining the knowledge of an expert with a NN based classifier.

Jan 1, 2003

By Paul Zick

The Port Authority of Allegheny County North Shore Connector (NSC) Project involves TBM excavation of twin 690 m (2,240 lf) precast segment lined light rail tunnels through soil and rock under the Allegheny River and a narrow, downtown city street. The $435 M project is funded 80% ($348 M) by the Federal Government, 17% ($72.5 M) by the State of Pennsylvania and 3% ($14.5 M) by Allegheny County. Along the tunnel alignment are a historic building on shallow foundations, modern buildings on deep foundations, and one building constructed directly over the alignment. The project includes construction of twin 369 m (1200 lf) cut and cover concrete box tunnels and an underground station shell. This paper provides an overview of general site conditions, current project status and construction challenges for the Twin Tunnels and North Shore Light Rail Station.