Search Documents

By J. Evans

Including: Tailings thickeners, CCD?s, paste thickeners, HI-rate thickeners, lamella thickeners, high compression thickeners, clarifiers etc. Flocculant dosing control for mining thickeners and clarifiers is influenced by a number of process factors. 1. Flow rate into the thickener or clarifier a) As the flow rate increases into the thickener or clarifier ?retention time? decreases which causes a greater affect hydraulically on the settling solids. So as the flow rate increases it will generally mean an increase in flocculant dosing rate. b) As the flow rate decreases into the thickener or clarifier the retention time increases which reduces the hydraulic affect on settling, improving settling rates. This will generally mean that as the flow rate decreases, we will decrease the flocculant dose rate.

Jan 1, 2011

By J. Stephen Slottee, Jerold Johnson

The use of a thickener, without filtration, to produce a non-settling paste (also called thickened tailings) with non-Newtonian rheology has been practiced in Australia for many years for the disposal of red mud. The application of paste thickening technology outside of alumina is relatively new. Interest and installations in paste thickening are rapidly growing. Water shortages and environmental pressures make consideration of thickening tailings to solids concentrations within the paste range necessary in most new tailings projects. The paste thickeners at the DeBeers CTP plant in Kimberley, South Africa are the latest example of paste tailings disposal on the surface, also called “stacking”. Houman (2003) The use of a paste thickener as an alternative to filtration for mine paste backfill is a more recently developed application. This paper describes the principles of design and general operating characteristics of a paste thickener compared to the conventional and high-rate thickener. The application and operating performance of paste thickeners in mine backfill is discussed as an example. An integrated approach to process design is described that matches the performance of the thickener, pumping system, and application on a common rheological basis to ensure that none of these steps prevents achieving process performance targets.

Jan 1, 2005

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

By Paul C. Schmall, Arthur B. Corwin, Derek Maishman

Ground freezing occupies a unique and important niche in underground construction, fulfilling a geotechnical need that is difficult, or sometimes impossible, to fulfill through other groundwater control and excavation support methods. Where complete groundwater cut-off and in-built ground support are required, and deep excavation is planned or the work occurs in difficult or disturbed ground, ground freezing offers the assurance critical to safe and timely construction. Compared with other groundwater cut-off or excavation support methods, a frozen wall is easily connected to underlying bedrock and will also adhere to adjoining subsurface installations or obstructions, if necessary, to provide a composite cutoff structure. Ground freezing is effective in all soil and ground conditions and has been used for emergency situations in disturbed, displaced or loose ground, where detailed soil characterization could not practically be performed.

Jan 1, 2005

By S. C. Langvik

The presentation named 'Dewatering of fines by Rotary Vacuum Disc Filters' has an opening why the filtration process is important to the Iron Ore Industry. It goes on to describe the various types of dewatering machines which have been used in this industry in the last 30-40 years, and where the vacuum disc filters now dominates. It presents also the most important design changes which have been made during this period to enhance performance. Further are discussed the principles of filtration and the factors and parameters which influence performance and operating costs. As a closing is presented today's ideas and thoughts about what can be foreseen of design modifications and improvements in disc filter design in the coming ten years.

Jan 1, 2001

By J. Wright

Since the 1960’s toroidal conductivity has been used to determine the Alumina to Caustic ratio of the digester discharge liquor stream. In recent years the application of ceramic materials have allowed the sensors to moved upstream to provide tighter control of the process. In the Bayer process, dissolving the aluminum contained in bauxite ore in caustic soda and converting it to aluminum oxide produces alumina. An important parameter of the process is measuring the alumina to caustic ratio in the digester discharge stream. The A/C ratio at a given caustic concentration is a measure of the degree of saturation of the alumina in the plant liquor. The aim in the process is to achieve a high A/C ratio. There is however a limit where precipitation will occur if the A/C ratio is too high. For many years conductivity has been used to determine the A/C ratio. Conductivity of discharge liquor is related to the caustic concentration. The change in the caustic concentration is in the same direction of the change of solubility of the alumina. Controlling the conductivity through adding additional bauxite ore and varying the dilution flow can increase plant yield.

Jan 1, 2001

By D. F. Machuca-Mory

A change of support model consists of a procedure to change a stationary histogram at a small data scale to represent a larger scale; typically a distribution of sample drill-hole data is changed to represent a chosen selective mining unit (SMU) scale. Most grade variables average arithmetically. Thus, the mean stays the same for different scales, and the variance changes according to well-established theory using average variogram values. The longstanding challenge has been to predict how the shape of the histogram changes. The discrete gaussian model is widely used because it appears reasonable and introduces few artifacts; there are no artificial minimum/maximum values and the target mean and variance are reproduced exactly. The resulting distribution shape, however, is strongly dependent on a multivariate gaussian distribution. The authors generalize the approach by taking advantage of a property of the isofactorial model, which allows one to specify where the random function falls on the spectrum between a low-entropy mosaic model and a maximum-entropy diffusion model. A measure of dissemination (MD) is computed using a ratio of the madogram and the variogram. The change of support algorithm is developed that uses a variable measure of dissemination (VMD) that is easily calculated and fit to data from the deposit. The resulting VMD change of support model is very flexible to represent different mineralization styles encountered in practice; global predictions of recoverable reserves are more accurate and decision-making is improved. A number of real examples are shown to demonstrate the approach.

Jan 1, 2008

By B. Farshadi, B. Asi, M. J. Habibian

"Dare-Zereshk deposit is one of the deposits supplies ore for Taft copper Complex in Iran Yazd province. This deposit is situated underneath a village the same name. Prior to mining activities, the village and its agricultural lands should be dislocated and deserted. This paper discusses about sustainability factors in this area including: Social and environmental effects of mining, dislocation and substitution of communities, created and lost jobs, financial and economic factors, quality of life index, infrastructures and post-mining land use. Studies have been performed by coupling Geographical Information System (GIS) with decision support tools such as Multi Attribute Decision Making (MADM), Through these studies revealed that considering the infrastructures developed for mine and plants, earned incomes and changing the community, mining activity in this area not only increases the social and regional sustainability but also improves it to a higher level."

Jan 1, 2011

By Gary B. Glass

Seventeen percent of US coal production now comes from the 19 surface coal mines in the Powder River Basin of northeastern Wyoming. The Powder River Coalfield, which coincides with this topographic and structural basin, is unique to the conterminous US, in that it contains an estimated 934.4 Gt (1.03 trillion st) of in-place coal resources. At least 13.2 Gt (14.6 billion st) is a compliant, strippable reserve base. In 1993, an estimated 162 Mt (179 million st), or 98% of the coal mined in this Wyoming coalfield, came from the thick - average 30.5 m (100 ft) - subbituminous, Wyodak coalbed, or from the Anderson and Canyon coals in the one mine where the Wyodak is split into two separate coalbeds. The other 2.7 Mt (3 million st) of coal mined in the Powder River Basin in 1993 came from the School, Badger, Monarch and Deitz No. 3 coalbeds. In this "world class" coalfield, there are at least 13 other persistent, 3 to 15 m (10 to 50 ft) thick, coalbeds as well as the Big George and Lake De Smet coalbeds, which are each 61 m (200 ft) or more thick in places. None of these latter 13 coals are mined at this time.

Jan 1, 1994

By Scott Rosenthal, David Gilkey, Michael McGivern, Lorri Birkenbuel, Daniel Autenrieth, Ty Murphy, Hadi Aldossari

A safety climate case study was carried out at a surface metal mine where investigators administered the Liberty Mutual Short Scale Safety Climate Survey to 365–368 miners to measure safety climate in consecutive years. Following the baseline safety climate survey in 2019, Foundations for Safety Leadership (FSL) training was conducted with 81 middle to upper management employees at the mine site. Investigators found statistically significant differences in the pre vs. posttraining FSL assessment scores of the middle to upper management employees who attended the training. The follow-up safety climate evaluation was compared to baseline scores and revealed no significant improvement. The overall baseline company safety climate score of 76.38 increased minimally to 76.50 (p-value = 0.616). Investigators also evaluated differences in safety climate between the company’s three major divisions (operations, maintenance, and administration). Both years administration had the highest mean score and operations had the lowest mean score. The authors attributed the statistically significant differences found among the three major divisions to various dissimilarities in their work environments.

Aug 13, 2021

By Scott G. Britton

Microcomputeranalysis has long been a technique for engineering professionals to improve the theoretical and practical design of continuous mining systems. Such work has been typically composed of modeling observed events and then introducing a variety of known elements with predicted results to compare against the results of the model. Programs written in BASIC, Cobol, Fortran or other language dominated such efforts. These programs have taken years to develop and prove out. This article explores a new management tool used daily at Tanoma Mining Co. (TMC) to track and improve continuous mining systems through the use of microcomputers and Lotus l-2-3 software. Data provided by section foreman, shift foreman, and maintenance personnel are analyzed against predetermined goals. In this way, new production targets are developed, weaknesses in the current mining systems are identified, and the results of changes are measured. The current results of this system on the productive output of TMC systems is on the order of 10% improvement. Thin seam coal mining is an industry within the broader industry of coal mining. Thin seam mining faces the same cost pressures and engineering problems as its higher-seam competitors without the advantages of moving volume per foot of extracted material to stay at an economic parity with others requires additional creativity within the management teams to extract higher productivity gains from the existing workforce and mining systems. TMC operates a deep mine in Indiana bounty, PA, about one hour northeast of Pittsburgh.

Jan 1, 1991

By Ian Hooper, Alan Winter, Stefan Sadokierski, Craig Covil

The existing Tappan Zee Bridge was built in the late 1950s and has been working over its design traffic load for some time now. A new project, which is being jointly sponsored by the New York State Thruway Authority and Metro-North Rail Road, is looking at new alternatives to provide new road and rail crossings of the Hudson River. These include 2 to 5 mile and potentially longer tunnel crossing options that include hardrock TBM and EPBM opportunities. The paper describes the project needs and tunnel concept design work done on some of the alternatives. It also relates to the current EIS process for the project and talks about a possible double-stacked tunnel option. It also talks about the geology and environmental constraints relating to tunneling and provides and introduction to the tunnel ventilation work necessary for tunnel crossing of this magnitude. It does not report on the bridge engineering options being evaluated.

Jan 1, 2005

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

Several of the larger copper projects recently built have included a molybdenum byproduct circuit as part of the overall project due to the favorable molybdenum market conditions and overall economic contribution to the project. This paper provides a summary of moly plant flotation practices across a number of both recent projects and historical ones. Modern Molybdenum flotation flowsheets predominantly incorporate self-aspirated cells and forced air cells with nitrogen addition. The paper provides insight into the process considerations, capital and operating costs associated with both of the cell types. It also reviews metallurgical aspects and important safety aspects. Other aspects including instrumentation and degree of automation are also discussed along with overall plant design.

Feb 27, 2013

By Dennis Ofiara

Several recent tunnel jobs have required special adaptations of hard rock TBMs. Some of the special job conditions are ?no blast? launch requirements, small shafts or launch pits, proximity to existing underground structures, and short tunnels where the TBM must be retrieved through the primary lining. This paper describes a few of these projects, and the machine adaptations that have made TBM excavation feasible.

Jan 1, 2008

By D. Rendini, R. D. Gutridge

INTRODUCTION Gwinnett County, Georgia, is a part of the rapidly expanding metropolitan Atlanta Georgia area. Located approximately 48 km (30 miles) northeast of Atlanta, Gwinnett County has a current population in excess of 600,000 and is projected to reach a population of 1,200,000 by 2025. As a part of the County’s master plan to supply drinking water for the expanding population and to increase system reliability, the Gwinnett County Public Utilities Department undertook the Shoal Creek Raw Water Intake and Pump Station Project. Figure 1 shows a vicinity map for the project. Prior to construction of the Shoal Creek Raw Water Intake and Pump Station Project the County had a single raw water intake to feed water from Lake Sidney Lanier (Lake Lanier) into a filter plant for processing into potable water. This project together with a newly constructed water filter plant provides Gwinnett County additional capacity and system redundancy to prevent interruptions to the drinking water supply. Lake Lanier is a man made reservoir with over 800 km (500 miles) of shoreline and was constructed by the Army Corps of Engineers in the 1950s for hydro electric power generation, flood control, and navigation benefits for the Chattahoochee River. Over time, Lake Lanier has become an increasingly important source of drinking water for the metropolitan Atlanta area. This paper focuses on the primary underground construction and lake tap components of the project including a 42.7 m (140 ft) deep pump station shaft 24.4 m(80 ft) in finished diameter transitioning to a 6.1 m (20 ft) finished diameter shaft, a3.05 m (10 ft) finished diameter by 19.8 m (65 ft) deep intake shaft constructed in an average of 21.3 m (70 ft) of water, and a 190.5 m (625 ft) by 3.05 m (10 ft) finished diameter modified horseshoe tunnel connecting the two shafts. This raw water intake system, in conjunction with the incorporated pump station with 8 pumps and dual1,829 mm (72 inch) pipelines, provides a system capacity of 1,091,062 m3/day(240 MGD) to two water filter plants and is expandable by the addition of pumps to1,500,210 m3/day (330 MGD). Parsons provided design and construction management services for the project. The $29.6 million contract to construct the project was awarded to W.L. Hailey &Company. Notice to proceed was given August 6, 2001 and substantial completion was achieved on January 20, 2004. Value engineering changes adopted for the project contributed to completing the project at a final cost of $28.8 million.

Jan 1, 2005

By Dale Matthews

The Getchell Mine, near Winnemucca, NR, was discovered in the 1930s and was initially mined to recover gold from oxide ores. During the 1940s and 1950s, gold was recovered from the highly refractory arsenic sulfide ores using horizontal kilns to roast the ores. During the 1960s, fluid bed roasters were used to oxidize the ore and recover the gold. The mine was shut down from 1968 through 1985. In 1985, heap leaching was started on the low-grade oxide ores that were available. In 1989, a pressure oxidation circuit was started to recover gold from the higher grade sulfide ores. Flowsheet The basic plant flowsheet of the Getchell Mine are shown in Figs. 1 and 2. The plant was designed to process a nominal 2.7 kt/d (3000 stpd) of ore with about an 85% onstream availability and a gold production of 15.5 kg/d (500 oz/ day). Run-of-mine (ROM) ore is fed directly to a wet semiautogenuous grinding (SAG) mill after the +457-µm (+18in.) rock is removed on a stationary grizzly. From the SAG mill, the ore goes to a ball mill where it is ground to 80% -75 µm (-200 mesh) and is then sent to a thickener. The SAG and ball mill operate in closed circuit using cyclones.

Jan 1, 1994

By Kevin G. Stricklin

Introduction Continuous monitoring techniques have been used in the US and abroad for many years. A continuous miner has a monitor that measures methane and automatically gives a warning if the methane exceeds 1%. It deenergizes the continuous mining machine automatically at a maximum concentration of 2%. Main fans are also continually monitored to ensure operation. Alarms may also be given at a remote location should a fan slow or stop. The systems being developed can continuously monitor various gases and equipment throughout the mine and transmit pertinent data to a surface monitoring station. At this station, conditions throughout the mine can be monitored and, in some instances, controlled. These are known as Mine Wide Monitoring Systems (MWMS). History The use of environmental monitoring systems began in 1976 when a federal court approved the petition of modification to use belt air at the face. The first mine to receive a modification did install a system to supplement existing safeguards. Later, the Mine Safety and Health Administration (MSHA) and the US Bureau of Mines (USBM) conducted tests dealing with the use of belt air. Findings from these tests are being used to set guidelines as requirements of a petition. These requirements include: • Velocity of air has to be 0.25 to 1.5 m/sec (50 to 300 fpm); • Monitors will be installed at each belt drive and tailpiece and at intervals not to exceed 610 m (2000 ft); and • An alarm level of 10 ppm, above the ambient level is appropriate. The early uses of environmental monitoring could only be used outby the last open crosscut. That may be a reason for an initial slow growth of these systems. In June 1982, MSHA began evaluating systems that could be used in returns to ensure that monitoring systems being used in areas where permissible equipment is required does not of itself pose an explosion hazard. This is known as the Mine Wide Monitoring Systems Evaluations and Sensor Classification program. The evaluations and classifications granted are based on electric currents and voltages. Use of mine wide monitoring systems The environmental aspect of MWMS in today's coal industry deals with carbon monoxide (CO), methane (CH4), and air velocity. Just as all mines are different and encounter different problems, the MWMS are diverse and can be used to provide necessary data in all areas of coal mines. Mine operators in an ultragassy seam, for example, may be concerned with monitoring methane, while a mine that used diesel equipment may want to continuously monitor for diesel contaminants. In a mine with roof fall problems, airflow monitors may be helpful as an indication of whether the air is flowing in its normal course and at its normal volume. Today's MWMS can monitor any or all of these parameters. Most systems can be expanded as mining needs require. For example, a mine is now being monitored for methane and five years from now CO monitoring would help increase safety. It may be possible to use the same system by adding additional equipment. In the US, 30 environmental monitoring systems were installed from May 1985 through May 1986. In 1984 and 1985, there were 38 and 44 environmental monitoring systems in operation, respectively. Due to mine closings, 11 of these are no longer in use. However, the number of mines using environmental monitoring systems increased to 63. Use of these systems are not limited to any geographic area or

Jan 9, 1987

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020