Search Documents

By N. D. L. Burger

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of steel wire rope slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist rope. This detaching is carried out via an additional detaching hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed to conform to established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted in most existing shafts. Given the simplicity and robustness of the designs, further development was recommended because of their enhanced self-sufficiency and reduced risk of malfunction. Keywords: underwind, overwind, deceleration, mineshafts, hoisting.

Jan 1, 2004

By W. J. Schlitt

The Namibian Copper Joint Venture has been formed to undertake development of the Haib copper deposit, one of the largest undeveloped copper resources in Africa. The development programme includes extensive hydrometallurgical testwork that is being managed by Kvaerner Metals (formerly Davy International).Various parts of the programme have been contracted to four third-party laboratories. The testwork involves sample selection and characterization, amenability tests, and a parametric study on the leaching variables. All portions of the programme are described and the results a represented. The ores selected for testing are quartz feldspar porphyries. The amenability tests include ?mapping? studies to assess optimum leach conditions, tests at high oxidation potentials, oxidation with various bacterial strains, and heap leach modelling. The parametric programme includes such variables as ore grade, leach temperature, crush size, pH, and ferric iron content of the lixiviant. Testing was done on both whole ore and concentrate. Results show that bacterial leaching is effective and that ore grade and temperature are key variables. Crush size and pH have less impact on copper extraction. For mid-grade ore, about 0.25 per cent copper, extraction is projected to reach 50 per cent after two years when heap leaching tertiary crushed ore at 60°C and pH 1.5. The heap leach operation would fit well with the proposed roast-leach operation used to treat higher grade ores. The latter could supply the low cost heat and acid needed in the heap leach.

Jan 1, 1999

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By A van Jaarsveld

Environmentally-friendly, safe and cost-effective technology for stope drilling has successfully been introduced at TauTona mine. It has enabled the problem of inadequate compressed air pressure and its downgrading impact on production capability to be overcome. The paper traces the development process which culminated in the conversion of the entire stoping operation at TauTona to electric drilling. Background work which took place at other mines is also described. Statistics of performance improvements are provided. 1. Introduction Holman?s Silver series and the Seco S215 were drills that had a measurable impact on the South African gold mining industry. It is too soon to say whether Hilti will join those great names. However, there is no doubt that the introduction of electric drills into the harsh and unforgiving world of deep level gold mining is a significant development. History has shown that being the first to enter a new technology is no guarantee of long-term success. The pain and suffering which accompany the birth of anything new can deplete the energy of the innovator while at the same time creating opportunities for competitors to leapfrog him. In addition to commitment and enthusiasm, the innovator must therefore also possess, or have access to stamina and resourcefulness to overcome the unexpected difficulties which will inevitably arise. All of these were needed for the Hilti project.

Jan 1, 2008

By Y. Y. Jiao, J. G. Cai

To investigate the dimensional effect on shock wave propagation in jointed rock masses, a 2-D and a 3-D calculation of a site test are performed respectively by using Discrete Element Method, the simulated results are compared with test data. It shows that, in modelling shock wave propagation and attenuation in jointed rock masses, when the explosive along explosion chamber is long enough and the joints are dense enough or uniformly distributed, the model can be considered as plane-strain problem, 2-D results are good enough to fit with test data. 2-D modelling, with much more details of rock masses taken into account, can be applied to make critical engineering judgements instead of 3-D modelling in some cases.

Jan 1, 2003

By E. Matinde, S. L. Msibi

"The robust nature of alumina refractory materials presents opportunities for their in-process reclaiming and re-use in non-critical applications. Virgin refractories can be substituted with different quantities of reclaimed materials without compromising the quality of the refractory products. In this study, the effect of reclaimed bauxite on andalusite-containing refractory castables for tundish applications was investigated. The recycled bauxite was formulated in different proportions to replace virgin andalusite in the castables. Standard tests were conducted to evaluate the physical, physicochemical, and thermochemical properties of the formulated products. Static corrosion tests were conducted using tundish slag in order to simulate the actual operating conditions. The results show that the standard flow behaviour, open porosity, and bulk density of samples containing up to 22 mass% reclaimed bauxite were comparable to those of the reference castable. However, high-temperature properties such as static corrosion at 1400°C and hot modulus of rupture at 1500°C indicated that there is an upper constraint to the amount of substitution. The study demonstrated direct potential savings of up to 10% when the reclaimed alumina replacement ratio was increased to 22 mass%. IntroductionAlumina-based refractories can be classified into low-alumina, containing less than 50% Al2O3, and high-alumina or bauxite, containing between 50 and 90% Al2O3. High-alumina refractories have widespread applications in high-temperature metal extraction processes due to their outstanding thermochemical and thermomechanical properties and stability (Rebouillat and Rigaud, 2002; Frulli, 2016). The typical chemical composition of refractory-grade bauxite consists of 85–90 wt.% Al2O3, 5–10 wt.% SiO2, 1–2wt.% Fe2O3, 3–4 wt.% TiO2, 0.4–0.8 wt.% CaO + MgO, and 0.20–0.8 wt.% K2O + Na2O (Nyoka et al., 2013). The thermochemical and thermomechanical properties of bauxite-based refractories rely principally on the conversion of the contained silica and alumina to the highly stable corundum (?-Al2O3) and mullite (3Al2O3· 2SiO2) phases (Rebouillat and Rigaud, 2002; Hill and Sehnke, 2006; Garbers-Craig, 2008; Frulli, 2016)."

Jun 1, 2019

By J. L. Viljoen

t has long been the drive of the industry and all operations to create an environment that is free of injury and illness. We have come a long way; the leaders, executives, managers, supervisors and workers are to be commended for relentlessly driving to create, what I call a ?White Flag Day Every Day?. Yet I am also aware of the huge shift we still need to create in the industry, on the operations and in the workplaces to have them free of injury and illness. Keywords People, values, care, trust, belief.

Jan 1, 2011

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

By C. D. K. Gauert

High-pressure waterjet technology is proposed as an alternative tool for selective underground mining of high-grade ore sections in stratiform orebodies showing a preferred ?bottom? or ?top? enrichment such as the Witwatersrand reefs and the Bushveld Complex platiniferous reefs. This technique, utilizing known mining technology together with more advanced machinery and additives as used in industrial and cleaning applications, may lead to an increased life-of-mine (LOM) for mining operations. A series of experiments was successfully carried out in a laboratory on Witwatersrand quartzite material, indicating acceptable cutting performance. Mining volumes by selectively cutting of reef portions are considered to be comparable to traditional drilling and blasting. Economic advantages of waterjet mining include energy savings due to the lower quantity of gangue rock to be hoisted to surface, as well as savings by a decrease in the usage of blasting materials. Capital expenditure of waterjet cutting, if applied on a broad scale, could be lower in the long term than that of conventional drilling and blasting methods. Mining by the application of high-pressure waterjet technology could become a competitive ?green technology? improving the economics and safety of labour-intensive mining operations. This paper suggests that waterjet cutting at an industrial scale can become a routine hard-rock mining technique in the future. Keywords waterjet cutting, high pressure, mechanized narrow reef mining, abrasive agents, costs, selective mining.

Jan 1, 2013

By J. Dahner

Total milling cost is composed of energy, liner and grinding media costs. In primary high ball load milling, the grinding media play the biggest role in total milling cost. This cost can be drastically reduced by improving the impact condition inside the mill. The impact condition inside the mill is influenced by shell liner design (as well as feed end and discharge design) and the type of discharge. The improvement of the impact condition will result in a significant decrease in grinding media consumption. The softened impact condition allows for better alloy optimization, resulting in a further reduction in grinding media consumption. Optimized liner design can also improve energy consumption as less energy is wasted in the projection of the grinding media. Magotteaux utilizes tools to simulate and show the grinding media trajectories for shell and end liners. This paper will present some practical examples where the media and energy consumption can be or has been reduced by optimizing liner design. Keywords Comminution, grinding, liner design, grinding media wear.

Jan 1, 2011

By J. Botin

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require more complex risk evaluation models that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, and production rates, among many other). In this context, real option valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed that successfully quantifies the risk associated with dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mine project. Keywords real options, risk management, risk quantification, dilution, minine planning.

Jul 1, 2013

By L. Holappa

Ferroalloys like FeCr and FeMn are mostly produced in submerged electric arc furnaces. Typical of these processes is that the amount of slag is quite high. The role of slag for the process is thus essential and specific chemical, physical and electrical properties are required. Slags in FeCr process are Al2O3-MgO-SiO2 based with minor contents of CaO and CrOx. Slags in the FeMn process are principally similar, originating from silicate minerals but can have quite large composition range depending on the manganese ore and its gangue minerals. Characteristic of the FeMn process is that the slag is rich in manganese oxide up to above 30%. A common feature is that the ?ore oxides?, CrOx and MnOx in slag are not only divalent oxides but also contain some higher valent of Cr3+and Mn3+, respectively. In FeMn production conditions the slag consists mainly of Mn2+. This is a clear difference from CrOx containing slags in which both two and three valent coexist in slags in FeCr process conditions. Oxidation state of the slag depends on the ambient oxygen partial pressure and temperature in the examined process. The thermodynamics of slags in ferroalloys, production are discussed in terms of phase diagrams, activities and oxidation state of chromium and manganese oxides. Further, slag properties influencing reduction kinetics and furnace operation i.e. viscosity and electrical resistivity are discussed. Keywords: review, slags, ferroalloys, ferrochromium, ferromanganese, thermodynamics, physical properties

Jan 1, 2004

By L. Lehasa

The purpose of the project was to investigate the challenges faced by Khutala Colliery pertaining to underground road construction and maintenance. Furthermore the influence of these challenges on productivity and safety requirements were taken into consideration. The operating standards required for the construction and maintenance of the 2 seam road transport infrastructure was investigated, together with reasons why the standards of operating procedure are not met. The Code of Practice put in place by Khutala Colliery was used to view the standard operating procedures. Leading practices on underground road construction were researched. The project aims to discover the gaps that Khutala Colliery must bridge to implement enhanced practices with regards to underground road construction. During the period of study, observations were carried out to determine whether the road construction standards of operating procedure were being adhered to at all times for both road construction and road maintenance. Khutala Colliery has put in place a traffic management plan, which includes safety practices and work policies that must be adhered to while travelling on underground transport roads.

Jan 1, 2012

By N. Singh

Merensky Reef is mined extensively within the Bushveld Complex. In previously mined-out areas on the Merensky Reef horizon there are pillars, potholes and remnants that have not been mined. These unmined blocks of ground on the Merensky Reef horizon can influence the mining of the underlying UG2 Reef. The extent of the influence will depend on the size of unmined ground and the middling between the two reef horizons. This paper quantifies the influence of partially extracted Merensky Reef on mining of the UG2 Reef, and aims to provide recommendations for mining strategies, as well as regional and local support to achieve efficient and safe extraction of the UG2 Reef, for various middlings beneath the Merensky Reef horizon. In some cases it was found that relatively shallow UG2 Reef mining could encounter conditions similar to those experienced in deep and ultra-deep mining environments.

Jan 1, 2005

By G. Apsey

Eutectic freeze crystallization (EFC) is a novel technique for the recovery of pure salt and pure water from hypersaline waste brines. It is therefore a promising technology for the treatment of industrial waste waters. The impurities caused by crystallizing salt out of multi-component brines by EFC have not yet been investigated, however. To these ends, the selenium impurity found in sodium sulphate, produced from the waste brine of a platinum operation, was investigated. It was believed that the similarity between sulphate and selenate ions allowed isomorphous substitution of selenate ions into the sodium sulphate crystals, which was the likely cause of impurity uptake. It was found that the presence of sodium chloride in the industrial brine promotes the uptake of selenium, while ionic strength of the brine and mass deposition rate of sodium sulphate did not have a significant effect on the selenium uptake. Isomorphous substitution is predicted to be the most significant mechanism by which all impurities will be taken up when applying EFC to other industrial waste brines.

Jan 1, 2013

By H. C. van Zyl

Mine water in the Upper Olifants River Catchment in Mpumalanga(upstream of Loskop Dam) is at times discharged into local streams, resulting in local acidification and regional salination of surface water resources. Pollution of surface water can be prevented by collecting and treating mine water to a quality where it could be re-used without restriction (Cleanwater 2020 Initiative). Mine water in the Olifants River Catchment currently amounts to only 4,6% of the total water usage, but contributes 78,4% of the sulphate load. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. A number of alternative desalination treatment technologies were investigated (subsequent to gypsum crystallization pre-treatment) where treated mine water must meet more stringent quality requirements (e.g. less than 200 mg/lSO4). The capital cost of these processes varied between R4 million/(Ml/d) and R10million/(Ml/d) and the running cost between R2/m3and R5/m3. Water usage in the Upper Olifants River Catchment currently amounts to 947 Ml/d (including the power stations), and will increase to an estimated 1385 Ml/d by 2020. The additional water demand by2020 (438 Ml/d) will have to be supplied by importation from neighbouring catchments, and more efficient utilization of the local water resources, including excess mine water. Various levels of treatment are required to make mine water suitable for the following potential applications (acceptable treated water sulphate concentration shown in brackets): irrigation (2000 mg/l), coal processing plant (1000 mg/l), general industrial use (500 mg/l), discharge to public streams (500 mg/l), potable use (200 mg/l) and cooling water in power stations (20 to 40 mg/l). The following two options, or a combination thereof, can be considered for management of excess mine water in the Upper Olifants River Catchment: ?Collection and treatment of excess mine water to a quality suitable for selected urban and industrial applications (Option A) ?Collection and treatment of mine water to a quality suitable for irrigation (Option B). The estimated capital and running cost for Option A amounts to R528.5 million and R55.7 million/year, respectively, compared with R68,2 million and R11,9 million/year for Option B. It is recommended that Option B be investigated for implementation in the short to medium-term. Option B was selected due to cost benefits and the initial favourable results obtained by a joint Water Research Commission and Coal Industry initiative where mine water is used for irrigation. Option A may become feasible in the long-term to ensure maximum environ-mental protection and reduced treatment cost as a result of anticipated technological improvements over the next 5 to 10 years.

Jan 1, 2001

By A. K. Singh

Between the main fan and the coalface in a mine a lot of air is lost through leakage at stoppings, doors, air-crossing etc. so that a much larger quantity of air has to be circulated by the fan in order that the stipulated quantity of air reaches the face. Stoppings are of vital importance not only for effective ventilation of underground mines but also for isolation of areas affected by fire or susceptible to spontaneous heating. Generally, isolation stoppings are made of brick in cement mortar. If the area is far from the pit or unapproachable, it is very difficult and sometimes impossible to build these stoppings. To overcome these difficulties, particularly near fire affected zones, an alternate successful attempt was made in Indian mines to make a plug underground, from surface through borehole, using cement concrete. In this paper the salient features of the methodology adopted for construction of the plug and the experimental procedure for the measurement of air leakage by SF6 tracer gas is described. Measurements of air leakage through rows of ventilation stoppings in two mines viz. Moira (Jambad and Kajora seams) and Kuardi11/12 (Niga seam) collieries of Eastern Coalfields Ltd. (ECL) have been incorporated. Results of experiments conducted at the Central Mining Research Institute (C.M.R.I) to determine leakage through25 and 38 cm thick brick stoppings are also discussed. Results of all these studies are compared, which show that the efficacy and reliability of the remote filled cement concrete plug in respect of air permeability is satisfactory.

Jan 1, 2004

By A. T. Visser

"SynopsisAlmost 20 years have passed since the cutting-edge research by Thompson and Visser on the design and management of opencast mine haul roads was conducted in South Africa. This system is based on three principles, namely the structural ability to support the ultra-heavy truck loads, the selection of vehicle and environmentally friendly riding surface, and an appropriate level of maintenance to counteract wear and tear. Obviously, proper layout and geometry are essential.These principles have been implemented worldwide, and it is useful to review the lessons learned. The objectives of this paper are to present a critical review of the status of mine haul road design and management, and the impact that these principles have made on operations, particularly the cost-effectiveness. The paper briefly reviews the principles of the haul road design and management and the extent to which they are applicable. Case studies of a number of implementations are presented to demonstrate that the principles are sound and have been applied effectively. For example, at an international operation the transport cost of coal was 40% more expensive than anticipated in the feasibility stage, and this made the mining operation uneconomic. Correction of this problem resulted in a viable enterprise. Although designed for opencast operations, the principles are equally valid for underground operations, and initial development work will be discussed.The main conclusions are that the research approach is valid and its effectiveness has been demonstrated in a number of applications. The anticipated financial benefit has been derived, and has made the mining operations that used the principles more effective. Of major importance is the application of opencast haul road design principles to the future thrust of using driverless vehicles in opencast and underground mining, where the road quality is not negotiable as there is no driver that can avoid obstacles or severe road deterioration.IntroductionAlmost 20 years have passed since the cutting-edge research by Thompson and Visser on the design and management of opencast mine haul roads in South Africa (Thompson and Visser, 1996a, 1996b, 1998, 1999, 2000a). This system is based on three principles, namely the structural ability to support the ultra-heavy truck loads, the selection of vehicle and environmentally friendly riding surface, and an appropriate level of maintenance to counteract wear and tear. Obviously, proper layout and geometry are essential."

Jan 1, 2015

By M. Andrews, B. J. Göhre, G. Strong, C. Terblanche

Mechanized mining can be experienced as a symphony by substituting the instruments for the different machines that each perform their own function and thus have different sounds. The drill-rig is the soloist around which all the other machines must play their part in harmony. Each machine can function on its own, but productivity is achieved only when all of the machines function in a holistic manner, as the different sounds of instruments form a symphony when playing together. To produce a symphony is to have the ability to put together all the pieces. It is the capacity to synthesize rather than to analyse. Today?s managers have to apply this harmonic way of thinking to make the system of mechanized mining work. In other words each of these people must have the ability of a conductor, whose job involves corralling a diverse group of notes, instruments and performers, and producing a unified and pleasing sound. At Modikwa Mine the introduction of the MAPS (Mine Activity Performance System) has allowed management to obtain a clear view of all the activities associated with the equipment. Through synthesis the issues that hampered productivity were identified and addressed to improve production and reduce costs.

Jan 1, 2006

By A. C. du Preez

Mintek has been involved in extensive test work since the early 1990s on the recovery of nickel and cobalt from leach liquors saturated in calcium, using synergistic solvent extraction systems. During this period the Nicksyn? reagent was developed, optimized, commercially manufactured, and tested by Tati Nickel on a demonstration plant for more than 2800 operating hours. Efficient recovery of nickel without the co-extraction of calcium, thus avoiding gypsum formation in the extraction and stripping circuits, was illustrated. This synergistic system was recently evaluated on a laboratory scale for the recovery of nickel and cobalt from synthetic lateritic sulphate leach liquor containing about 3 g/L nickel, 0.5 g/L cobalt, 0.7 g/L manganese, 20 g/L magnesium, and with calcium at saturation. Extraction and stripping parameters were determined for this feed liquor and are discussed in this paper.

Jan 1, 2014