Search Documents

By M. Kawakami, K. Suzuki, T. Takenaka, S. Yokoyama

Molten NaNO3-NaNO2-KNO3mixture is used as a heat transfer medium at high temperature. One of the most important properties of this mixture is the heat capacity. In the present work, the enthalpy change with temperature was measured by the drop calorimetric method to evaluate the heat capacity. The results are summarized as follows: The enthalpy of the mixture increased linearly with the temperature. From the slope of the line, the heat capacity was evaluated. The heat capacity of pure NaNO3, NaNO2and KNO3was 0.129,0.110 and 0.142 kJ/mol/K, respectively. These values are in fairly good agreement with the published data. In the binary and ternary systems, the molar additivity of heat capacity, which is well known as Neumann-Kopp’s law, was obtained. The heat capacity of HTS1and HTS2, which are well known ternary mixtures of practical use, were in the range of published data.

Jan 1, 2004

By J. P. F. Charpin

The transport of large boulders in a furrow from a mining area to a nearby pond was considered. The furrow is filled with a mixture of water and soil particles flowing down to the pond at high velocity. Due to operating constraints, the slope of the furrow is reduced progressively. A relationship is derived, relating the slope of the furrow and the composition of the fluid to the maximum size and shape of the transported boulders. The characteristics of the boulders carried all the way down to the pond may then be determined.

Jan 1, 2007

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

This paper characterizes the copper cycle, that is, the flows of copper entering and leaving the African economy over a one-year period (1994). The major flows over the entire life-cycle of copper are examined; these include production (mining, milling and refining), fabrication of semi-products and manufacturing of finished products, use, and the waste management system. The results reveal that substantial amounts of copper (of order705 Gg/yr) are mined in Africa; of that amount, about 70 per cent is exported following processing, 18 per cent is utilized by African fabricators, and 12 per cent is discarded. The flows of copper products from African fabricators and product imports from other continents exceed product discards by large amounts. This difference, about 0.25 kg Cu/capita/yr on average, is added to in-use stock, largely as wire, plumbing tube, and in electronics. Some 65 per cent of the copper in discard flows is contained in electrical and electronic products, where it is relatively easy to collect and process for reuse. About a third of the copper discard flows known is recycled. The actual percentage is almost certainly higher because of informal (and unrecorded) recycling. Much of the remaining discarded copper is diluted into the municipal waste stream, where recovery and recycling are probably not economically justified. Keywords: material flow analysis, resource management, material budgets, copper, stocks and flows, systems analysis, Africa, developing country

Jan 1, 2003

By L. A. Cramer

Platinum metal was first utilized by the Inca civilization in South America where it was found in alluvial deposits along the San Juan and Atrato rivers that lie between the Andean mountain range in Colombia and the Pacific Ocean. The nuggets found in these rivers average between 77% and 86%platinum, 7%?8% iron and small amounts of copper, gold and other Platinum Group Metals (PGMs). The Incas often alloyed platinum with copper to increase its workability and fabricated various ornaments from it.

Jan 1, 2001

By J. W. van der Merwe, A. Palazzo

"Owing to the corrosiveness of the untreated brackish cooling water typically used for steel mills (and other environments), it is important to treat the water and monitor corrosion in such systems. Generally, corrosion rates are monitored with corrosion probes inserted into a pipeline or vessel. This has been standard practice for many years, and is widely accepted in industry. Typically, two kinds of probes are used - electrical resistance and linear polarization resistance (LPR) probes.In this study, the effectiveness and accuracy of the LPR technique was evaluated by comparing the electrochemical measurements with the results of mass loss tests using corrosion coupons. The corrosivity of the environment, a synthetic brackish water, was varied by varying the calcium hardness and alkalinity, and to simulate actual plant conditions temperatures of 35°C and 45°C were used. In addition to the corrosion rate measurements, the iron concentration was measured, as well as the imbalance from the probe.The corrosion rates obtained by LPR were from 57% lower to 385%higher than those from the immersion tests. Most probe measurements were higher than the immersion results, and 50% of the probe results were50% or more higher than the immersion results. The best correspondence between the two methods was obtained at low calcium levels, except for one measurement that was 93% higher than the coupon results. There was no clear correlation between parameters such as temperature and total alkalinity and the difference between the results. It would therefore appear that LPR measurements can differ significantly from immersion results, and LPR results should therefore be used with caution in industrial applications."

Jan 1, 2015

By H. Gumede

The occurrence of fracturing due to high stress levels is a major factor in hangingwall stability in deep level gold mine stopes. However, rock falls cannot be the result of these fractures alone. Rock falls can result only from the occurrence of unstable rock blocks defined by the interaction of the stress induced fractures and naturally occurring geological planes of weakness. These planes include bedding planes and joint set planes. However, there is a general lack of information on the characteristics of these planes (orientations, spacings and lengths)?it does not appear that any such systematic and quantified information, if collected, has been published. To remedy this situation to some extent, joint mapping exercises have been carried out in several geological environments in two gold mines. The data collected on joint geometry included orientation, spacing and length, and this information is included in the paper. In addition, the paper describes the use of the data collected to evaluate the potential for rock falls and the probability of failure of stope support

Jan 1, 2007

By P. K. Hofmeyr

Base Metal (Cu, Ni, Mo, Zn, Co etc.) analysis traditionally has been very slow in conventional analytical laboratories which can lead to additional costs being incurred in waiting time of drill rigs or mining excessively off-reef. Recent developments in the automation of analytical laboratories now allow for very rapid turn-around times for base metal analytical data which can help reduce such costs as well as reduce the unit costs of the analyses themselves. 2.0 CONVENTIONAL ANALYTICAL LABORATORY PRACTICE Conventional analytical laboratories are necessarily are very manual. Sample preparation is slow and laborious, samples are moved from stage to stage manually and, typically, all samples are processed in batches so a sample which is the first to be, say, milled has to wait for the complete milling of the batch before it advances to the next stage eg. mixed with wax prior to pelletising for XRF analysis. Inevitably this results in long sample data turn-around times for laboratories handling large numbers of samples. Manual sample preparation can only be accelerated by increasing staff which increases costs and can lead to additional errors being introduced. Cleaning of sample preparation equipment, eg. crushers and mills, between samples is essential to avoid cross-contamination between samples and this is slow and labour-intensive. In manual sample preparation the correct sample numbers staying with the samples is totally dependent on the efficiency of laboratory operators. It is extremely difficult to detect when errors have occurred due to the switching of sample numbers during the sample preparation stages. Running duplicates and QC samples at best is only partially successful in detecting when sample number switching errors have occurred. Errors of this nature and cross-contamination problems due to incomplete cleaning of sample preparation equipment tend to occur when laboratories are working at pressure due to high sample numbers and when supervisors are not present during 24/7 laboratory operations which is often required on plant process control laboratories. These problems are common to all conventional analytical laboratories and their magnitude is dependent on the level of control and efficiency of QC systems practised by individual laboratories. The disadvantages of conventional manual analytical laboratories can be summarized as follows:- 1. Labour-intensive which is costly especially when multiple shifts have to be used during 24/7 operations.

Jan 1, 2005

By W. Abdellah

The purpose of this paper is to establish a qualitative method to estimate the risk level (e.g. rating and ranking) resulting from mining activity. Risk is the product of two factors: probability of failure and cost of consequences. A resultant assessment scale matrix is then used to assign a risk index value which is directly proportional to the potential for excavation instability. A case study, the No. 1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario will be examined. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) is presented for a mine development intersection situated 1.5 km below ground surface. The developed assessment scale matrix is used to estimate risk index for intersection (2981) located on 5000 level. The results are presented and categorized with respect to risk-index value, probability of instability, cost of consequence, and mining stage.

Jan 1, 2014

By J. Dienenthal

Automatic Charging and Stoking Machines for use at ferroalloy furnaces are in operation for more than 20years. Dango & Dienenthal Maschinenbau GmbH (short: DDS) has developed several machine generations. Today advanced solutions help to achieve better charging and stoking results to minimize cost and to improve the working environment around the furnaces. Three different alternatives can be considered: Rail-mounted solution The machine(s) travel(s) on an overhead monorail to one or several furnaces and is locked in the desired working position from where charging and stoking is performed. Mobile solution This machine travels on the charging platform and is also locked at the respective working position to perform charging and stoking. Automation of a standard mobile charging and stoking machine A standard charging and stoking machine can be adapted for automation. A reliable navigation system is included. Charging and stoking is performed with the moving machine. Advantage versus other solutions: considerable lower investment cost and possibility to upgrade the mobile charging and stoking machine for later automation. Overall, automatic charging and stoking can save up to 10 per cent of the specific smelting energy. A better and more consistent furnace operation can be achieved. Different programs are used to cope with different furnace conditions and changing raw materials. All machine movements can be recorded and correlated to other furnace parameters. Working environment on the charging platform is greatly improved.

Jan 1, 2007

By I. J. Barker

Keywords: Submerged-arc furnace, plasma furnace, d.c. furnace, scale up, Søderberg electrodes, smart grid, demand side management, load shedding This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferro-alloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase a.c. electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become a more complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to get cheaper power from the organisations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of d.c. power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

This paper reports on recent field observations on the performance of support systems under different corrosion environments in Canadian underground mines. Phenomenological data are used to gain a better understanding of the main causes of corrosion in underground metal mines. Preliminary field data collected from five metal mines have been complemented by atmospheric and water sample analysis as well as fractography and metallographic studies. This has identified dominant factors that control the corrosion of support systems. The data are analysed in order to develop a support strategy for mines operating in corrosion environments.

Jan 1, 2008

By F. Lombard

We consider the Grubbs estimation of the precision of an online gauge. Typically, this type of estimation involves independent results from two or more reference instruments (sampling and laboratory analysis operations). The properties of the estimator are then independent of the product variability. However, the use of more than one reference instrument entails significant additional costs. The two-instrument Grubbs estimator, which is based on results from a gauge and a single reference instrument, has the disadvantage that its standard error is heavily dependent on the degree of product variability. We propose a new estimator that has a variance that is more or less independent of product variability. In fact, the variance is typically less than that of the Grubbs estimator based on the use of two reference instruments. In order to function successfully, our methodology requires some prior knowledge of the extent of product variability and of gauge precision. In practice, such prior knowledge is often available and it is a weakness of the traditional two - and three-instrument Grubbs methods that no use is made of such knowledge. The efficacy and robustness of the new method is illustrated by Monte Carlo simulation.

Jan 1, 2012

By F. Agterberg

In his 1978 monograph ‘Lognormal-de Wijsian Geostatistics for Ore Evaluation’, Professor Danie Krige emphasized the scale-independence of gold and uranium determinations in the Witwatersrand goldfields. It was later established in nonlinear process theory that the original model of de Wijs used by Krige was the earliest example of a multifractal generated by a multiplicative cascade process. Its end product is an assemblage of chemical element concentration values for blocks that are both lognormally distributed and spatially correlated. Variants of de Wijsian geostatistics had already been used by Professor Georges Matheron to explain Krige’s original formula for the relationship between the block variances as well as permanence of frequency distributions for element concentration in blocks of different sizes. Further extensions of this basic approach are concerned with modelling the three-parameter lognormal distribution, the ‘sampling error’, as well as the ‘nugget effect’ and ‘range’ in variogram modelling. This paper is mainly a review of recent multifractal theory, which throws new light on the original findings by Professor Krige on self-similarity of gold and uranium patterns at different scales for blocks of ore by (a) generalizing the original model of de Wijs to account for random cuts; (b) using an accelerated dispersion model to explain the appearance of a third parameter in the lognormal distribution of Witwatersrand gold determinations; and (c) considering that Krige’s sampling error is caused by shape differences between single ore sections and reef areas.

Jan 1, 2015

By A. D. Pelton

The evolution of thermodynamic models of molten salts and slags, starting with Temkin in 1948, has culminated in today?s sublattice models. These modern models have permitted the development of large thermodynamic databases of model parameters, which can be used to calculate and predict accurately the properties of multicomponent solutions. The model parameters are mainly obtained by the critical evaluation and optimization of available thermodynamic and phase equilibrium data for binary and ternary subsystems. The models are then used to estimate the properties of multi component slags and salts from these assessed binary and ternary parameters. When used in conjunction with thermodynamic databases for solids and solid solutions (salts, oxides, sulphides, metals, etc.), other liquid solutions (such as liquid metals),and gases, these databases permit the calculation of complex multiphase equilibria in multicomponent systems, with applications in a wide variety of industries. These calculations can be performed with general commercial software for Gibbs energy minimization, which can also be incorporated into process simulation software packages. Keywords: slags, salts, solution models, thermodynamics, phase diagrams, oxide systems, molten salts

Jan 1, 2004

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By F. T. Cawood

The distinction between real estate ownership and that of interests in the property is fundamental to the appraisal of mineral properties. This distinction affects the nature and understanding of security of tenure and, consequently, the perception of what constitutes fair value. Legal matters are a particular concern because of their influence on security of tenure, ownership definition and use restrictions. The dynamics of the market and the complex interrelationships between the factors of production define value at a specific point in time for the bundle of rights, interests and assets that constitute a mineral property. Because each mineral property is unique, physically immobile and of a wasting nature, its usefulness to its owner and society must be optimized. The US Appraisal Institute (2001) classified the forces that affect land use as the cultural, political and economic attitudes of society. These forces culminate in laws that often dictate the purposes for doing appraisals. Once the legal definition of the asset is understood, valuers can decide on the valuation process that will support the final valuation approach.

Jan 1, 2004

By X. Bai

A new heuristic sublevel mining stope optimizer is presented. The optimizer seeks the best locations and lengths of a series of vertical raises that, together with the blocks linked to each raise, define a mining stope. Five design constraints ? the footwall angle, the hangingwall angle, the number of raises, the maximum distance of a block from a raise, and the minimum width required to move the farthest block towards the raise ? allow the shape of the sub-stopes associated with each raise to be controlled. The optimization is done on the locations and lengths of raises using a genetic algorithm to efficiently sample the parameters? space. For each raise, a local network is defined in cylindrical coordinates around the raise such as to impose the design constraints. A maxflow algorithm on the local network is used to determine the optimal sub-stope for each raise. All substopes are combined to define the global stope for the entire deposit. The best global stope is obtained using a genetic algorithm to find the raise parameters providing the best profit over the entire deposit. Two synthetic cases and one real deposit are used to evaluate the new algorithm and compare the results with the single-raise optimizer. The multiple raises approach leads to significantly improved economics compared with the single-raise stope optimizer, and the dilution is also substantially reduced compared to the single-raise case.

Jan 1, 2014

By L. Mpolokeng, J. P. Labuschagne, H. Yilmaz

"An investigation into pillar cutting was carried out at a platinum mine on the western limb of the Bushveld Complex. The focus was on crush pillar design and implementation in order to ultimately improve the compliance percentage for pillar cutting. The major findings from the investigation suggest that the pillar cutting problem lies with the implementation of the design rather than the design itself. Observations of the practical issues underground that prevent good pillar cutting were made. After these issues had been identified, recommendations to rectify these problems and a few other issues identified during the investigation were provided. The recommendations are aimed at improving the pillar cutting compliance and reducing the likelihood of pillar bursts or pillar runs, which will ultimately create a safer mining environment. Paper written on project work carried out in partial fulfilment of BSc. Eng. (Mining Engineering)"

Jan 1, 2015

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004