Search Documents

By M. J. Nicol, P. D. Scott

The kinetics of the non-oxidative dissolution in acids ofthe iron sulphides FeS, Fe-FeS, and Fe9S10 were studied by the use of rotating-disc electrodes of the various compounds. It was found that the rates of dissolution vary by orders of magnitude with changes in surface potential. The dissolution rates depend on non-integral orders of hydrogen-ion concentration, which in turn vary with potential. A mechanism based on the following premises is proposed to explain the kinetics of dissolution of the iron sulphides. (I) Only an FeS compound that is exactly stoichiometric dissolves in accordance with the accepted theory of ionic charge transfer. (2) Any non-stoichiometric iron-deficient iron sulphides must be reduced to exactly stoichiometric FeS before spontaneous non-oxidative dissolution can occur. The dissolution of Fe.S1o and slightly iron-deficient FeS compounds under open-circuit conditions occurs only when an oxidation reaction (usually the oxidation of hydrogen sulphide to elemental sulphur) can provide the electrons necessary for the production of exactly stoichiometric FeS. The establishment of such a mixed-potential system is the reason for the induction period that occurs during the dissolution of pyrrhotites in acids.

Jan 1, 1979

By B. P. Watson

The Bushveld platinum group metal deposits in South Africa are the largest in the world. These deposits occur as two distinct stratiform tabular ore bodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2300 m. The mining method is a variation of planar open stoping. Crush pillars are widely used to support the open stopes. These pillars are designed to fail and the residual strength provides the required support resistance to stabilize the stoping excavations. This paper describes the in situ measurement, of stress within a Merensky pillar from Impala Platinum. These measurements were used to derive a stress-strain curve that includes pre and post failure behaviour. 2D FLAC modelling, with strain softening, was done to investigate how damage expands into the hanging- and/or footwall. Although the so-called ?squat? effect is always present, the modelling suggests that it does not dominate the pillar system behaviour at larger width to height ratios. Punching of the pillar into the hanging- and/or footwall increasingly controls the pillar system behaviour with larger width to height ratios. The paper investigates the behaviour of a system that incorporates the immediate hanging- and footwall, as well as the pillar itself.

Jan 1, 2009

By D. Limpitlaw

Industrial mining in Zambia started in the 1930s when the world class copper deposits near the border with Katanga were developed. The discovery of these deposits began at the turn of the century when the first claims in the Copperbelt were pegged at Chambishi, north of what became the town of Kitwe1. World War I and the difficulties of raising sufficient capital for such large scale undertakings delayed the exploitation of these deposits. Following this hesitant start, a large copper mining complex was built, resulting in the development of five major towns, all highly dependent on the mining and beneficiation of copper and cobalt. Copper became so important to the country that, on independence, the only non-mining town to make it onto a list of the top six was the capital, Lusaka. From commissioning of the mines to the end of the colonial period in 1964, copper production increased to just over 640 000 t annually2 (see Figure 1). After the establishment of the new Zambian state, production continued to increase, supported by a benign legislative environment and strong international copper prices. The government of Kenneth Kaunda was intent on improving the conditions of the rural poor and reducing unemployment in urban areas. To this end, the government embarked on an ambitious project of refocusing Zambia's economy away from the colonial role of commodity supply to one of decentralized mass employment. The Copperbelt industrial complex was key to the success of this approach, and in 1969 the Zambian State acquired a 51 per cent stake in Zambia's two main copper producing companies: Roan Selection Trust and Rhodesian Anglo American Corporation. The former became Roan Consolidated Mines Ltd (RCM) and the latter became Nchanga Consolidated Copper Mines Ltd (NCCM). In the year they were nationalized, the mines produced at least 720 000 t of copper? and employed approximately 48,000 workers (see Figure 2)2-4. The subsequent economic policies of the Zambian Government depended heavily on the state's ability to monopolize the proceeds of copper mining.

Jan 1, 2011

The following corrections should be made to pages 346 and 347 of the December 1981 issue (vol. 81, no. 12) in the paper by O. L. Papendorf entitled 'A note on rapid determinations of present values in the presence of growth and inflation'. (1) Equation (2) on page 346 should read as follows:

Jan 1, 1982

By M. P. Mohring

A School on the Total Utilization of Coal Resources, which was organized by the Technical Programme Commitee of The South African Institute of Mining and Metallurgy in conjunction with the South African Coal Processing Society, was held in the Civic Theatre at Witbank from 30th October to 2nd November, 1989.

Jan 1, 1990

By R. Morris, W. D. Clough

SYNOPSIS The design of an opencast coal mine over areas previously mined by underground mining methods presents several potential methods of mining the coal. The paper describes some basic methods of mining for the No. 2 seam of the Witbank Coalfield, which had previously been mined by the bord-and-pillar method.

Jan 1, 1985

By HORNICKA OSTRAVA

The Czechoslovak Scientific-Technical Institute has arranged the international conference 'Hornicka Ostrava' for four or five days at the end of October, 1969, as part of the preparation for the international 'Miners' Congress' on deep coalextraction in 1970. The keynote of the conference is 'New Techniques in coal mining,' and will be covered by five groups dealing mainly with: 1. New trends in the opening of mines, optimal parameters, projections, equipment, utilization of computers for economic analyses, etc. 2. Increase in efficiency of coal extraction in deep mines, technology, concentration, pressure control, optimization of material and coal transport. 3. Modernization of devices for increased safety and working conditions, new trends in explosives, new techniques for reducing environmental diseases. 4. Innovations in deep level coal extraction, mechanization, rationalization, automation, etc. 5. Other topics about modern techniques in mining. Address your enquiries to: Ing. Karel Kalas (Secretary of the Conference), Dum Techniky Cs YTS, Ostrava 1, Jesenkiho 7-9, Czechoslovakia.

By K. A. Annan

The last seven hot rolling passes of the ferritic stainless steel AISI430 were simulated on a Gleeble-1500D® thermo-mechanical simulator to investigate the effect of temperature, strain rate, and interpass time on the texture. The compression tests were carried out over a wide range of strain rates (0.1 s-1 to 5 s-1) and temperatures (1100°C to 820°C) with different interpass times (2, 10, 20, and 30 seconds). The dynamic recrystallization to dynamic recovery transition temperature was determined from examining the relationship between the mean flow stress and the inverse of the deformation temperature in multi-pass tests. It was found that the texture in the central layer of the compressed sample is a strong recrystallization-type. The through-thickness textural and microstructural banding, to a large extent, were found to be weakened by hot deformation in the two-phase (a+ ?) region, as opposed to the single-phase (a) region.

Jan 1, 2013

By K. A. Moxham

The ARM 1100 was described in a paper presented at the 6th International Symposium on Mine Mechanization and Automation in September 2001. It started operation underground at Rowland Shaft in early 2002. This paper covers the results of those trials that resulted in more than 1 100square metres of UG2 being mined.

Jan 1, 2004

By A. O. Filmer

An account is given of a study on the non-oxidative dissolution in aqueous acidic solutions of nickel sulphides of different stoichiometric composition, in which a rotating ring-disc electrode was used. The rate of dissolution was found to depend on the potential of the sulphide and the nickel-to-sulphur stoichiometric ratio. A maximum rate for the dissolution of nickel from nickel sulphides containing an excess of nickel was recorded at potentials around -0,2 to -O,3V. The rate decreased markedly at more anodic potentials. For nickel-deficient nickel sulphides, the nonoxidative dissolution rate increased with a cathodic shift in potential. Under open-circuit conditions, a nickel sulphide of a composition approximating Ni ,S. reacted most rapidly. The dissolution rate was controlled by either a chemical or an electrochemical reaction at the electrode surface, had an activation energy of between 50 and 65 kJ.mol-1, and was independent of stirring speed.

Jan 1, 1980

Contribution by W.D. Ortlepp In the Journal of May 1994, the authors first presented the concept and analysis that formed the basis for a design approach for deep tunnels, now expressed more explicitly in the present paper (March/April 1996). In a contribution in the Journal of March/April 1995, I expressed a certain disquiet about the validity of their original approach. The authors responded to these criticisms in the same issue. It is apparent to me now that both the contribution and its rebuttals were written, probably for different reasons, in such an obscure and pedantic way as to further confuse the reader rather than provide enlightenment. My concern still persists. But in order to avoid further confusion I will attempt to pose my uncertainties and difficulties in a much more direct way. On page 98 (top of 2nd column) in the earlier paper, an important statement concluded as follows: '. . . the horizontal ellipse requires 140 per cent less force for equivalent stability'.

Jan 1, 1996

By J. H. Fourie

This paper highlights modern practices in ore-treatment plants, with particular reference to the flotation of P2O5 at the plants of the Phosphate Development Corporation (Foskor) at Phalaborwa in the northern Transvaal. The following aspects are covered: design criteria, equipment and personnel, production standards and control. cost control, maintenance, and process development.

Jan 1, 1981

By R. G. B. Pickering, B. Ebner

The hard rock gold and platinum mines in South Africa have seen little development in the technology of mining. Holes are still drilled in the rock—though the latest water hydraulic rockdrills will complete that task in two minutes compared with the eight hours for hand drilling. Charging up is with far safer explosives and with available initiation systems it is no longer necessary to run up the face lighting each fuse. Movement of rock in the stope is predominantly by means of scraper buckets and scraper winches — these were first introduced in the 1920s.Support is still mainly rock, either in sit pillars or backfill, or alternatively wood. Just as themining process has changed very little it is hardly surprising that the productivity of mining is also relatively unchanged. Major efforts have been made to mechanize the mining process. However, most of the narrow reef mines where ‘trackless mechanized mining’ was introduced in the early 1980s have reverted to conventional mining. In the wider reefs mechanized mining is the option of choice, unfortunately most of the gold and platinum mines have very narrow reefs that are not suitable to’ off the shelf’ equipment. The move to introduce room-and-pillar mining into the narrow UG2reefs is at the expense of mining more waste with the reef, fortunately it appears that appropriate waste and reef separation processes are available. Room-and-pillar mining followed by long holedrilling and blasting of a narrow slot of reef out of the pillars currently appears to offer the best of both worlds—maximum reef recovery with minimum waste dilution. All these mining methods are still dependent on blasting to break the rock. The cyclic nature of mining by blasting places severe constraints on the rate of face advance that can be achieved and consequently the utilization of the invested capital. For narrow reef hard rock mining to break out of these constraints and to really make progress in the 21st century it is necessary to follow the lead of the soft rock mining industry and change the technology of mining. In the underground coal mining industry, coal cutting has been proved to be the most cost-effective solution. In narrow reef hard rock mining the future must be based on the development of non-explosive methods of rock breaking that in turn are integrated into continuous mining systems. Non-explosive so that the mining operation can be conducted on a continuous basis, with nodelays for the removal of blasting fumes. Continuous mining also maximizes the return on the capital invested in developing the mine. Rock cutting will define the stope width and that in turn will be designed to minimize waste dilution; it will also minimize damage to the hanging and create a safer environment. Mechanization makes it possible to automate the mining process and further improve safety by positioning the operators in a safer environment. This paper defines the work to evaluate cutting processes carried out by Sandvik TamrockVoest Alpine. The evaluation was in the UG2 and the pyroxenite and norite typical of the Merensky Platinum Reefs. A novel form of mining machine is proposed that will utilize existing technology. Finally the paper describes the interaction between Sandvik Tamrock Voest Alpineand Lonmin Platinum and the initiation of an agreement to develop and trial a prototype hard rock narrow reef mining machine.

Sep 1, 2001

Gerhardus Paulus Badenhorst passed away on 2nd December, 1989. Badie, as he was known to all, will be missed by his many friends and colleagues, and will be remembered by al who knew him as a warm-hearted person who was totally dedicated to the safety and health of the workers in the mining industry.

Jan 1, 1990

By M. Rudman, L. Pullum, L. J. W. Graham

Centrifugal pumps are the workhorse of hydraulic conveying systems but their performance is derated when viscous non-Newtonian fluids, such as pastes and/or coarse solids are present. The reduced performance for purely viscous Newtonian fluids may be calculated using techniques such as the Hydraulic Institute method, but similar deration for non-Newtonian fluids is not so easy to apply. As part of the AMIRA P599 project investigating high concentration suspension pumping, centrifugal pump tests were systematically conducted on a wide range of non-Newtonian coarse particle suspensions. Suspension sup to 38% v/v of coarse particles with mean diameters in the range of 1.1 < d50< 3.4 mm suspended in carrier fluids with dynamic yield stresses of 0 < t?< 17.2 Pa and shear thinning indices in the range 0.35 < n< 0.79 were examined. Techniques such as the Hydraulic Institute de-ration method require a characteristic shear rate to be assigned before application with a non-Newtonian fluid, and a method based on pump geometry, fluid rheology and flow rate is proposed. This method predicts the dramatic characteristic reduction in head at low flow rates that is often observed and explains why larger pumps are relatively insensitive to this form of head deration. Head deration due to the presence of coarse particles in non-Newtonian carrier fluids is seen to follow similar trends to that of Newtonian suspensions and often dominates the total deration procedure.

Jan 1, 2007

1. Reviews Steel and its heat treatment, by K-E Thelning. 2nd Edition. London, Buterworths, 1984.678 pp. R201,60 (incl. OS1). Reviewer: J.P. Hofman The Southern Queensland Conference 1985. Parkvile (Australia), The Australasian Institute of Mining and Metallurgy, 1986. A$ 15.00. Reviewer: R.B. McGilivray Rock mechanics, by A.R. Jumikis. 2nd edition. Clausthal-Zelerfeld (West Germany), Trans Tech Publications, 1983. US$ 58. Reviewer: R.W.O. Kersten The XVIth International Coloquium on Refractories. Freiburg, West Germany, 1985. DM 80. Reviewer: H.J. S. Kriek Diamond driling handbook, byW.F. Heinz. Johannesburg, South African Driling Association, 1985. 517 pp. R30. Reviewer: S.A.G. Martins Processing and utilization of high sulfur coals, edited by Y.A. Atia. Amsterdam, Elsevier, 1985.788 pp. Oft. 385. Reviewer: L.M. Falcon Weighingand proportioning of bulk solids, by Hendrik Colijn. 2nd edition. Rockport (U.S.A.), Trans Tech Publications, 1983. 398 pp. $60.00. Reviewer: G. Cunningham Investment appraisal and economic evaluation of mining enterprise, by S. von Wahl. Clausthal-Zelerfield (West Germany), Trans Tech Publications, 1986. US$ 40. Flotation of sulphide minerals, edited by K.S. Eric Forssberg. NewYork, Elsevier Science Publishers, 1985. 480 pp. US$1O1.75. Reviewer: T.R. Twidle 5th Meeting of the European Clay Groups (5th Euroc/ay Meeting), Prague, edited by J. Konta. Praha (Prague), Univerzita Karlova, 1985. Reviewer: D. Bibmann 2. Recent publications CSIRO. Research review1982-84: CS/Ra Division of Mineral Engineering. Melbourne, Commonwealth Scientific and Industrial Research Organization, 1985. 77 pp. The world copper market: structure and econometric model, by Gerhard Wagenhals. Berlin, Springer- Verlag, 1984. 202 pp. DM 37,00.Materials data of high-strength aluminium aloysfor durability evaluation of structures, edited by L. Schwarmann. Disseldorf (West Germany), Aluminium- Verlag GmbH, 1985. BRITISH GEOLOGICAL SURVEY. UnitedKingdom mineral statistics 1985, compiled by H.c. Squirel, A. Jones, N.E. Sharp, M. Lowe, and D. Slater. Keyworth (U.K.), the Survey, 1986. 175 pp.3. Mintek reports Report Ml66D The effect of calcining on the recovery of gold in a sand residue. (1st issued Sep. 1984.) Report M168D The treatment of Uitkomst concentrate. (1st issued Oct. 1984; reissued Mar. 1986.) Report M175D Supergene alteration at the Pering zinc-lead deposit: The nature and extent of the oxidation zone. (1st issued Oct. 1984.) Report M176D Bench-scale tests on the extraction of cobalt and nickel from COMAT leach liquors. (1st issued Nov. 1984; reissued Mar. 1986.)Report M241 PLA TO at Mintek. Report M243 The performance and wear characteristics of grinding media as affected by metallurgical and dimensional factors. Project development The Second Project Development Symposium on Planning, Construction and Commissioning will be held in Sydney, Australia, from 7th to 10th October, 1986. Hosted by the Sydney Branch of The Australasian Institute

Jan 1, 1986

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 27th August, 1969, at 4.15 p.m. Mr. R. C. J. Goode (President) was in the Chair. There were also present seventy Members, ten As¬sociate Members, two Affiliates, one Student and twelve Visitors making a total of ninety-five. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: "It is my very sad duty to announce the deaths of the following members of the Institute: Mr James Charles Napoleon Humphreys, a Life Member who joined the Institute on 1st April, 1935, and passed away on 6th February, 1969. Mr Michael John Worrall, Graduate Member, who joined the Institute in 1960 and passed away on 2nd June, 1969. Mr Eric Adam Conrad Dickson, Associate Member, who joined the Institute on 13th June, 1952 and who passed away on 8th June, 1969. Mr Robert Jack, Associate Member, who joined the Institute on 2nd August, 1956, and passed away on 14th June, 1969. Mr R. A. H. Flugge-de-Smidt, Honorary Life Member and Gold Medallist, who joined the Institute in 1922 and passed away on 17th June, 1969. Mr John Gordon Craig, a Member who joined the Institute on 23rd August, 1960, and passed away on 6th August, 1969. As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, I would ask you to rise and observe a few moments silence." MINUTES The President: "May we confirm the Minutes of the General Meeting held on 18th June, 1969, as published in the July, 1969, issue of the Journal?"-Agreed. WELCOME TO VISITORS The President: "We are honoured this afternoon by the presence of the Institute&apos;s Honorary President, Mr R. S. Cooke, President of the Chamber of Mines of South Africa, and by one of our Honorary Vice-Presidents, Mr T. L. Gibbs, the Government Mining Engineer, as well as by the presence of many distinguished guests, to all of whom I extend a most cordial welcome. We are happy to have present, Mr S. C. M. Naude, Director of the Witwatersrand Technical College, Mr G. A. P. Louw, Vice-President of the Associated Scientific and Technical Societies, Mr R. P. Randall, Senior Vice-President of the South African Institute of Electrical Engineers, Mr W. T. L. Wayman, President of the South African Institution of Mechanical Engineers, Mr D. F. Odendaal, President of the Institution of Certificated Mechanical and Electrical Engineers of South Africa, Mr E. Haacke, President of the Institute of Land Surveyors of the Transvaal, Mr B. L. Loffell, Vice-President of the South African Institution of Civil Engineers, Mr J. F. Leatherbarrow, President of the South African Institute of Assayers and Analysts, Dr W. S. Rapson, President of the Joint Council of the South African Scientific Societies, Dr P. L. Carman, President of the South African Chemical Institute, Mr F. Jackson, President of the Federation of Societies of Professional Engineers, Mr W. E. Kirkwood, President, S.E.I.F.S.A., Mr J. Steele, President of the South African Institute of Foundrymen, Mr M. Waite, President of the South African Institution of Welding, Mr M. R. Gericke, President of the South African Council of Professional Engineers, Mr G. C. Sowry, Chairman, Witbank-Middelburg Branch, Mr T. Groenewald, Chairman of the South African Chemical Institute (Southern Transvaal Section), Professor O. B. Volckman, Chairman of the South African Institution of Chemical Engineers, Mr H. W. Le Roux, Chairman of the South African Federation of University Engineer¬ing Students, Dr R. E. Robinson, Director of the National Institute for Metallurgy, Mr P. H. Anderson, Deputy-Chairman of Rand Mines Limited, Mr E. Boden, Manager of the A.S. and T.S. and Count Folchi-Vici, from Italy, who has lime interests in this country. I also extend a very special welcome to the lady guests here this afternoon, and to all the visitors." MEMBERSHIP The President: "I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Members: Stuart Denston Hill, Robert Roy Richardson, Gert Paulus van der Vyver. Affiliates: Henry Clifford Read, Allen Edward Hooper, Alan Edwin Edkins. Graduates: Lester Winston Sturgess, Erroll Vincent Bosman. Students: Terence Vernon van Heerden, David Curtis Lindley. MEMBERS TRANSFERRED TO A HIGHER GRADE From Associate Member to Member: Andries Willem van Zyl, Roy Lardner, Nugent Gerald Ward Comyn. From Student to Graduate: Michael John Worrell (now passed away), Peter John Hamilton Short. I wish to welcome the new members to the Institute, and to congratulate those members who have been transferred to a higher grade." ANNUAL REPORT OF THE COUNCIL AND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1969 The President: "Ladies and gentlemen, It is with much pleasure that I present to you the Annual Report and Accounts for the year ended 30th June, 1969. These have been laid on the chairs and before calling for their adoption I would like to make a few comments. The Accounts show an excess of expenditure over income of R2,124 and our Honorary Treasurer, Mr D. G. Maxwell, will in due course comment on this. The main difficulty has again been the cost of the Journal and I think most of you are aware of the changes that we propose to make. I shall be sorry to see the last of our old format but then I have always had rather a con¬servative outlook.

By H. M. Friede

Discussion of the above paper by A. SIFF The steely nature of the Iron Age objects mentioned in Dr Friede&apos;s paper point to two hypotheses. (1) The African iron workers were conversant with the art of direct steel manufacture. (2) They were less knowledgeable of the art of the production of carbonless iron. In this context I cannot but quote T. A. Wertime.

Jan 1, 1980

By Lesley Andrews

"Electron microbeam analysis of metallurgical samples covers a broad field and has applications in the areas of minerals processing, hydrometallurgy, pyrometallurgy, physical metallurgy and corrosion.Some idea of the possibilities of microbeam techniques can be illustrated by examining the following example of a run of mine gold ore sample. Milling and bulk chemical analysis of the ore will provide major and minor element analysis as well as the gold grade. More detailed chemistlY can also reveal the presence of trace elements that may be advantageous or deleterious to downstream processing. Electron microbeam analysis can provide additional information in the form of - size, liberation, association and composition of the gold, the percentage of refractory gold, the size, liberation, association and composition of enclosing sulphide or arsenide phases and the levels and association of the trace elements that may affect processing. In most cases electron microbeam analysis compliments bulk chemistry, and does not replace it. Both techniques should be used in parallel for maximum effect.This paper touches on the origin and history of electron microbeam techniques, as well as the theory behind microbeam analysis and processing. The more common types of instruments and their applications will also be dealt with briefly - more details on, and examples of, the applications and choice of technique will be covered in the presentation.Mosely first discovered, in 1913, that the frequency of emitted X-radiation excited by an electron beam is a function of the atomic number of the analysed element. This discovery led to the development of spectrochemical analysis. The forerunners of the electron microanalysers of today, however, were only invented during the nineteen fifties. The electron microprobe was developed in parallel by Castaing and Guinier in France and by Borovski in Russia, but Castaing&apos;s design was the basis of modern microanalysers. The initial area of analysis was brought down from over 1 mm2 to less than 2 µm, as it is today. In 1956 Cosslett and Duncumb invented the scanning electron microprobe, where a beam of electrons could be scanned across an area of a sample. This, in turn, led to the development of the electron microprobe with both scanning and point analysis capabilities that we know today.Essentially, all electron microbeam instruments operate by the production of a beam of electrons from a filament in a vacuum (i.e. an electron gun). The electron beam leaves the gun and is accelerated and focused by a series of electromagnetic lenses while passing down an evacuated column. The electrons eventually strike the surface of the sample to be analysed and may travel through a thin sample (transmitted electron microscopy) or react with a thicker sample to produce several reflected kinds of radiation."

Jan 1, 2014

By A. Singh, R. R. Maclachlan

SYNOPSIS A back-analysis procedure based upon 35 mm photography was developed on a laboratory scale for the pur¬pose of determining the percentage of oversize particles known to be present in heaps of fragmented rock. Eight simple blends of crushed stone containing varying percentages of oversize on a 1:40 modelled scale were examined. Simulated test conditions for the following were subjected to the photographic study: (1) a bench heap, (2) the surface exposure of a partially excavated heap, (3) a gravity-sorted surface as occurs on an apron dump, and (4) four quadrant views of an incrementally built conical heap of rock fragments. The best back-analysis determinations were obtained from (4), the cone, over all eight blends of fragments. The mean error was within -0,16 per cent of the true value, with a range of ± 1,872. This was for oversize contents of 5 to 20 per cent where a minimum 25 per cent of the photograph area was processed by digitizer. The worst results were from the apron dump at - 1,462 per cent for a mean error of ± 4,174 per cent. The intermediate results were from the undisturbed bench at -0,186 per cent with a mean error of ±2,862 per cent.

Jan 1, 1989