Search Documents

By I. Y. Motovilov, S. A. Telkov, M. B. Barmenshinova, Z. S. Abisheva

As a rule, removing waste rock at the beginning of the process improves the conditions for the flotation of minerals, and also reduces the operating costs of crushing, grinding and flotation. Lead-zinc ores in the Shalkiya deposit of the Republic of Kazakhstan are classified as difficult for enrichment, but taking into account their significant reserves, they are one of the main potential ores for the production of lead and zinc. Under industrial conditions, for processing ores of the Shalkiya deposit, a selective flotation concentration scheme with the production of lead and zinc concentrates is recommended. However, according to the recommended scheme, it is not possible to obtain high-quality concentrates of lead and zinc, with high metal recovery. The paper presents the results of studies of preliminary gravitational enrichment of lead-zinc ore in the Shalkiya deposit. Based on the fractional analysis for the particle size range of -40+8 mm, Henri- Reingard enrichment curves were constructed, separation density (2730 kg /m3) was established to isolate the light fraction with the lowest possible lead and zinc content, and gravity enrichment indices (0.7-0.71) were determined. It was found out that when using gravitational enrichment of the original large-sized ore in the Shalkiya deposit, tails are released at the beginning of the technological process with a yield of up to 20% with the extraction of silica up to 30%, calcite up to 11% and carbonaceous matter up to 12%. As a result of the studies, it was found that the beneficiation of crushed lump ore could be conducted in heavy suspensions. One of the positive aspects of the use of gravitational enrichment is the reduction of energy costs for grinding the heavy fraction, which was experimentally proved in this article. Keywords: Lead-zinc ores, Shalkiya deposit, fractional analysis, gravitational enrichment, floating fraction, sunken fraction, separation density

Jan 1, 2020

By M. S. Moholwa, J. D. Steenkamp, H. L. Rutto

Manganese ores are the major source of manganese for the production of manganese ferroalloys. There is a gap in the knowledge of the decrepitation behaviour of manganese ores, which presents a problem in the operation of smelters. Decrepitation, which is the breakage of the ore particles upon heating, is an important quality parameter for these ores. The purpose of this investigation was to determine the extent to which South African manganese ores decrepitate during preheating in a rotary kiln. The effects of temperature, rotational speed, and particle size decrepitation were investigated. Manganese ores were heated in a laboratory-scale rotary kiln at temperatures of 600, 800, and 1000°C, and rotational speeds of 3, 6, and 12 r/min. The size ranges were +6-20, +20-40, and +40-75 mm and the residence time was constant at 30 minutes. The decrepitation index (DI) is quantified as the ratio of the mass of <6 mm particles after pre-heating to the total mass of the sample. It was found that the DIs for all ores used were proportional to the temperature and the rotational speed and inversely proportional to the particle size range with temperature being the most important parameter. Ore A was the most susceptible to decrepitation followed by ore C and ore B; this was mainly to the decomposition of kutnohorite, the content of which was the highest in ore A and the lowest in ore B.

Nov 30, 2022

By Z. Leng

"After detonation of the explosive, the final blast-induced damage area around the blast-hole falls into three categories, namely crushed zone, fractured zone, and elastic deformation zone. This paper presents a modified model to calculate the size of crushed zone around a blast-hole in drill-and-blast, with the hoop compressive stress and cavity expansion effect taken into account. The material in the crushed zone was assumed to be a granular medium without cohesion, but with internal friction. On this basis, the formula for crushing zone radius was derived. The proposed approach was verified with tests reported in the literature and the simulated results from SPH-FEM coupled models. A full statistical analysis was also carried out, and the predicted values were found to be in better agreement with the test results compared with other models. A sensitivity analysis of the modified model showed that the size of the blast-induced damage area is mainly affected by the following factors: rock mass properties, in situ stress, and borehole pressure. In particular, the roles of borehole pressure and in situ stress are discussed. Finally, suggestions are made on how the size of the crushing zones can be decreased. IntroductionOver the past decades, drill-and-blast has become the most commonly used technology in rock excavation. It is well known that in rock mass fragmentation with explosives, the annular rocks around the blast-hole are converted into fines. The formation of these fines consumes a significant part of the energy of the detonation, which in general is ignored in the determination of the efficiency of detonation (Glatolenkov and Ivanov, 1992; Furtney et al., 2012). Many studies show that only 20–30% of the total explosive energy is effectively used in fragmenting the rock, and up to 50% of the energy generated by conventional charges is wasted in overcrushing of the crushed zone and the inner part of the fractured zone (Ouchterlony et al., 2004; Sanchidrian et al., 2007). How to control the crushed zone to enhance the effective utilization of explosive energy, reducing the unit explosive consumption and the engineering cost, is therefore of great significance."

Jan 1, 2016

By J. Petersen, T. Moyo, J. Dinga

The leaching of chalcopyrite in ferric sulfate media is notorious for its slow and inhibited kinetics. Different methods have been proposed to improve the kinetics, including the use of organic compounds as additives to the leaching media. In this study, the enhancing effect of methanol, ethanol, 1-propanol, and 2-propanol on the leaching of chalcopyrite in aerated acid ferric sulfate solutions using different reactor systems was investigated. The results revealed a clear improvement of copper dissolution by methanol and 1-propanol relative to tests with no additives under similar conditions. Operating a continuous-flow mini-column reactor yields surprisingly good results, potentially related to the maintaining of a consistent leaching micro-environment on the mineral surface. Scanning electron microscopy studies showed that the alcohols result in the removal of surface deposits formed during the anodic dissolution, potentially thus facilitating improved cathodic reduction of the ferric ion to drive the anodic dissolution.

Jan 1, 2023

By Y. J. Cao

The purpose of this study was to investigate the flotation behaviour of unburned carbon in a cyclonic-static microbubble flotation column (FCSMC). The ash sample, collected from a power station in Guangdong province of China, was characterized by size analysis, X-ray diffraction, contact angle measurements, and X-ray fluorescence. The effect of the column flotation operating variables on the removal of unburned carbon from the fly ash was systematically studied. The feasibility of separating unburned carbon and ash was determined from the removal rate of unburned carbon (RUC) and loss on ignition (LOI). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil dosage was 600 g/t, pulp density was 20 per cent, superficial gas velocity was 1.4 cm/s, and circulating pressure was 0.20 MPa. The results indicate that the FCSMC technique is effective in removing the unburned carbon from the fly ash, which can be attributed to the generation of microbubbles and the continuous cyclonic circulation method. Under the optimized conditions, a cleaning ash with 2.13 per cent LOI and 94.21 per cent RUC was obtained.

Jan 1, 2012

By R. Letsaole, H. Mabowa, J. Sehat, J. Tshilongo, T. Rampfumedzi, N. Ntsasa, A. Mkhohlakal1

This study explores the use of co-collectors to enhance the recovery and determination of rhodium during fire assay with lead collection, followed by acid dissolution using conventional hot plate methods. Rhodium, a critical platinum group metal, poses analytical challenges due to its low natural abundance and complex chemistry. Among the co-collectors tested, palladium and tellurium demonstrated significantly improved rhodium recoveries, ranging between 100% and 120%, whereas silver resulted in poor recovery and higher error margins. These findings highlight that co-collectors can enhance the efficiency and sensitivity of platinum group metal analysis, although their effectiveness is dependent on the chemical interaction with the target element. Acid dissolution was essential to ensure complete digestion of prills prior to analysis, enabling accurate quantification of rhodium. Overall, the findings suggest that palladium and tellurium are effective co-collectors for rhodium determination in fire assay, while silver and lead flux alone are unsuitable. This work provides important insight into optimising fire assay procedures for reliable rhodium analysis, with potential benefits for platinum group metals recovery and economic evaluation.

Mar 6, 2026

By X. Chen, G. Wang, D. Wan

Computational fluid dynamics have been applied for detailed modelling of particle-bubble collisions. The most accurate approach in the previous work is using the point particle method to treat particles and bubbles. Nevertheless, the sizes of particles and bubbles are generally bigger than the Kolmogorov scale in the high turbulence of the flotation environment, which makes the point particle method inappropriate. This paper describes particle-resolved direct numerical simulation on the collisions between particles (denoted as heavy particles) and bubbles (denoted as light particles) in a homogeneous isotropic turbulent flow field, and a comparison with the point particle method.. A largescale stochastic forcing scheme was implemented within the mesoscopic multiple-relaxation-time LBM approach to maintain turbulence intensity at targetted levels. Both kinematic and dynamic collision kernels were evaluated to study the correlation of total collision events and turbulent kinetic energy (TKE) dissipation rate. The results show that collisions between particles increase with the TKE dissipation rate as radial relative velocities between particles increase with it. In the particle-resolved simulations, the dynamic collision kernels were found to not match with the kinematic collision kernels as in the point particle method. Quantitatively, they were approximately 4 to 10 times smaller than the corresponding dynamic collision kernels. Therefore, it is not reasonable to estimate the kinematic collision kernel in particle-resolved simulations as its rationales are not valid. However, the collision behaviour can still be accounted for by means of the dynamic collision kernel since it is obtained from the direct statistical analysis of the collision events. Keywords: Lattice Boltzmann Method; particle-resolved simulation; multiphase flow; collisions

Jan 1, 2020

By U. Atici, R. Comakli

"Understanding rock properties is of vital importance in mining and civil engineering. Rock properties are generally determined through laboratory tests, which require a large number of uniformly shaped samples and technicians who use indirect methods to determine rock properties. The texture coefficient (TC), which represents various textural parameters including the size, shape, orientation, and relative proportions of grains and the matrix, is an efficient means for indirectly evaluating the mechanical behaviour of rocks. In this study, 12 different rocks (ten granites, one diorite, and one gabbro) were collected and their engineering properties. including specific gravity, porosity, P- and S-wave velocities, Schmidt rebound hardness, uniaxial compressive strength, and elasticity modulus, were investigated. Relationships between TC and these measured properties were assessed. Statistically significant (at the 95% confidence level) correlations were found between the TC and compressive strength, elasticity modulus, sound velocity (both compression and shear waves for dry and saturated samples), but no significant correlation was found with Schmidt rebound hardness. The results suggest that it is possible to use the relationships between TC and the mechanical properties of rocks in rock classification. IntroductionIn every aspect of rock engineering, knowing rock properties is essential for determining and predicting the behaviour of rocks and rock masses. Mechanical properties of rocks are important parameters in mining, geology, and engineering, and they are affected by textural characteristics such as grain size, grain shape, cement type, degree of cementation, mineral content, and the ratio of the grain area to the matrix area. The effects of textural properties on the physical and mechanical properties of rocks have been investigated for a long time, and previous studies revealed close relationships between single parameters related to rock texture and mechanical properties of rocks (Akesson et al. 2001; Gunsallus and Kulhawy 1984; Merriam, Rieke, and Kim, 1970: Onodera and Kumara 1980; Prikryl 2006; Ulusay, Tureli, and Bider, 1994; Tugrul and Zarif 1998). Rock properties are usually determined using mechanical tests, which require uniformly shaped and relatively large samples. However, it is not always possible to obtain such samples. Furthermore, rocks with similar textural and structural properties may exhibit different mechanical behaviour. Howarth and Rowlands (1987) developed a texture coefficient (TC) that expresses all the main textural parameters of a rock in a single dimensionless quantity based primarily on statistical assessment. The TC makes it possible to understand the effects of a rock’s textural properties on its mechanical properties using thin sections instead of large, uniform samples. Ersoy and Waller (1995) investigated the relationship between strength and TC for limestone, sandstone, and siltstone; they also examined the effect of rock properties and TC on drilling performance. Ozturk, Nasuf, and Bilgin (2004) explored the relationship between rock quality and TC by evaluating the uniaxial compressive strength (UCS) values of limestone, basaltic andesite, and tuff. Gupta and Sharma (2012) evaluated TCs as well as the petrophysical and mechanical properties of quartzite from the lower and higher Himalayas and found a strong relationship between TC and UCS. Similarly, Ozcelik, Bayram, and Yasitli (2013) investigated the relationship between TC and various parameters in marble by applying the statistical analyses developed by Ozturk, Nasuf, and Kahraman (2014)."

Jan 1, 2019

By J. A. Batista-Rodríguez, F. J. López-Saucedo

A new methodology is proposed for the preliminary assessment of coal blend quality, which combines gamma-ray spectrometry and magnetic susceptibility measurements. This methodology does not replacethe conventional methods of assessing coal quality, but can help to control the quality of the coal blending process, as well as reduce the amount of proximate analysis required and the determinations of calorific value and total sulphur. The methodology includes five steps. First, both geophysical measurements aremade with handheld equipment. The samples with magnetic susceptibility ≤ 1 × 10-3 SI are then separated. From these samples, those with total gamma intensity ≤ 20 nGy/h are separated. These samples have a higher calorific value and lower ash and moisture content. To separate the samples of better quality and with lower total sulphur content, in step four the samples with total gamma intensity > 20 nGy/h are separated from those with magnetic susceptibility ≤ 1 × 10-3 SI. This last group includes samplesthat will cause less total sulphur-related environmental pollution. In the final step, the quality of both radioactive sample groups is corroborated from the calorific value measurement and ash, moisture, andtotal sulphur contents in at least 10% of all coal blend samples from both groups. In this study, more than1000 samples were analysed with this new methodology, and the results are remarkably similar to the ASTM classification of the Sabinas Basin coals.

Apr 2, 2022

By S. O. Bada

Coal is a complex mixture of organic and mineral constituents and is the most abundant resource of fossil energy in the world. In recent years, significant research into dry coal beneficiation has gained much attention, primarily due to the need to improve grades and reduce the environmental contaminants in coal without the use of water, and to achieve this in as cost-effective manner as possible, relative to wet beneficiation processes. This paper seeks to review the application of various electrostatic separators with their process principles, to draw comparisons between different dry beneficiation techniques with specific emphasis on the tribo-electrostatic separation method, and finally to report the results of tribo electrostatic separation conducted on various South African coals. Previous research conducted on Indian, European and American coals has indicated that this technique is likely to lead to significant economic benefit through the reduction of ash content, NOx and more specifically Sox by separating out the liberated Fe-S-bearing minerals prior to utilization. The removal of the latter suite of minerals is also likely to significantly reduce or eliminate the emissions of associated trace elements, including mercury and arsenic. The research results reported in this paper indicate that the rotary tribo-electrostatic process has the potential for significant upgrading of high ash pulverized South African coal. The impact of various operational parameters was investigated and key factors established for the optimum recovery of low ash and low sulphur fine coal.

Jan 1, 2010

Traditionally, the term `total system&apos; design applied to comminution conjures images of a design that addresses the usual business and operational drivers, including health, safety and environment (HSE), capital cost, operating cost, throughput and product size. In terms of the physical process, the mine to customer type studies also exemplifies an approach that satisfies a normal `total systems&apos; approach. As an industry there are drivers that are forcing a re-consideration of what we regard as our total system. This modification of drivers will require changes in approach and implementation to provide the best solutions. Some of the major changes that impact the drivers are shortage of skilled personnel, changing social attitudes to remote mine site work, greenhouse gas emissions (GHGE), quality of available orebodies and geographical location of new mine sites. One approach to the challenges presented by the changing business environment is to expand the system envelope around comminution to ensure that comminution, in its widest sense, helps to meet the new realities. Background to the new drivers and constraints is provided and some of the appropriate responses are examined in relation to the impact on the total system.

Jan 1, 2007

By J. E. Xu, J. Y. Zhang, M. Q. Sheng, K. Wan

"SynopsisThe densities of selected CaO-Al2O3-MgO slag systems were measured at 1823K by the Archimedean method. Thirteen different slag compositions were chosen based on different levels of the MgO content and the mass ratio of CaO/Al2O3. The results indicated that the density of the slag decreases with increasing MgO content (from 0–3.78 mass%), but increases with further increases in MgO content up to 11.33 mass%. At a fixed MgO content of 5.5%, the trend of density change with CaO/Al2O3 in the slag is similar to that for changes in MgO content. On the basis of the regular solution approximation rules of excess molar quantities, an attempt was made to estimate the molar volume of the slags investigated. The application of the molar volume model confirmed that the present expanded approximation rules are applicable to predict the molar volumes of the melts discussed.IntroductionDensity is one of the most important fundamental properties of slags, which influences metallurgicaly phenomena in many ways. Density is sensitive to the nature of the chemical bonds and the species in the melt, and is of great importance not only for theoretical research on the structural properties of molten slags, but also for industrial applications. Density is also required to estimate other key properties used to assess the behaviour of high-temperature molten oxides, e.g. viscosity, surface tension, and thermal conductivity.Liquid calcium aluminate slags that contain magnesia are the basis of most ladle slags for secondary refining processes. The CaO-Al2O3 binary phase diagram (Hallstedt , 1990) shows the eutectic composition (50 wt% CaO and wt% Al2O3) has the lowest melting temperature. The main emphasis of this study is on the 12CaO·7Al2O3 refining slag with MgO additions. The CaO-Al2O3-MgO ternary system is of considerable importance in industrial metallurgical processes, and is fundamental to the understanding of metallurgical slags, ceramic materials, and geological phenomena."

Jan 1, 2015

By S. Bradshaw, A. Mabentsela

"Physical and numerical modelling methods were followed to identify mechanism(s) for tundish slag entrainment in a bare tundish and one with a flow control device (FCD).The physical and numerical models made use of water and paraffin to model steel and slag respectively. Observations from the physical model showed that the steel-slag interface remains immobile in both cases. Entrained paraffin formed droplets approximately 1 mm in diameter. Results from both models (numerical and physical) showed that in both cases (bare and FCD case), areas of high entrained slag concentration exist near the inlet region. The entrained slag concentration decreases towards the tundish endwalls.Flow patterns and velocities tangential to the steel-slag interface from the numerical model showed that slag entrainment in both the bare tundish and tundish with a FCD possibly takes place via two mechanisms. First, the slag moves across the steel-slag interface via mass transfer; secondly small velocities tangential to the interface at depths greater than 10 mm below the interface carry the already ‘entrained’ slag into the bulk steel phase. These tangential flow patterns are dominant in the inlet region, hence the high concentration of entrained slag in this region. IntroductionThe tundish serves as the last metallurgical vessel through which steel passes before solidifying in the moulds. It is in the tundish that the last traces of non-metallic inclusions should be removed, otherwise the inclusions carry over to the moulds and cause defects in the steel product. In the tundish, the slag is less dense than the melt and thus resides on the top of the melt. The slag provides a sink into which the non-metallic inclusions float to and dissolve. The slag also protects the melt from air and heat loss. However, when slag is entrained in the melt as a result of increased turbulence or shearing at the steel-slag interface, slag can become a source of nonmetallic inclusions.Numerous studies on flow patterns in the tundish have been carried out since the introduction of the tundish. These studies were aimed at improving the flow characteristics in the tundish (Chattopadhyay, Isac, and Guthri, 2010; Cloete, 2014; Jha, Dash, and Kumar, 2001; Jha, Rao, and Dewan, 2008;"

Jan 1, 2017

By Y. Belloa, C. Dorfling

The presence of impurities such as Se and Te in copper sulfate leach solutions can have a detrimental effect on electrowinning efficiency. These elements can be removed from the solution by precipitation; sulfurous acid is commonly used as a precipitation reagent, while studies have also reported improved precipitation with the addition of metallic copper. This paper aimed to determine the effect of conditions used during the solution purification step on the characteristics of the precipitates that formed. Precipitation tests were performed in a batch reactor with copper sulfate leach solutions obtained from the base metal refinery of a platinum group metal producer. The effects of agitation rate (250 and 500 rpm), SO2 flow rate (4.4 and 5.8 mL/min.L), temperature (65 and 95°C) and metallic copper powder addition (0, 1 and 2 g/L) on the characteristics of the precipitates formed during the tests were determined using scanning electron microscopy. The major phases detected in the precipitates formed when using SO2 as the only precipitation reagent were elemental Se and Cu2Se. The introduction of copper powder led to the production of different sulfide phases for the experiments conducted at 65°C irrespective of the values of the other reaction parameters. At 95°C, Cu crystals, Cu2O and tiny inclusions of Cu2(Se,Te) were the prominent phases noticed in the precipitates produced from all the tests conducted with copper powder as precipitation enhancing reagent. Keywords: copper, precipitation, selenium, tellurium

Jan 1, 2020

By Ri McCrindle

"Analytical Chemistry is moving rapidly towards a concept where technicians have to do no more than press a button and print the result from an instrument that is a featureless ""black box"". In this environment we must ask how much traditional &apos;&apos;wet chemistry"" is still required for undergraduate students.Methods that can be fully automated will become increasingly important. An example of such a method is that of the slurry nebulisation and ICP-OES analysis of precious metal concentrate. Grinding the sample and adding Triton X100 as dispersant, complete analysis time is in the order of 90 min as apposed to the traditional Carius tube method which could take as long as 24 h. For most of the elements studied, the results using ""in-house"" reference material for calibration and as samples as well were within the 95% confidence level. Elements of low concentration in the sample (As, Bi and Se) were not within that level."

Jan 1, 2014

By N. F. Dawson

Recovery of a chromite concentrate from UG2 flotation tailings streams, of a grade suitable for further pyrometallurgical treatment for the production of ferrochrome, has certain specific challenges not only by virtue of the decoupled nature of the primary PGM recovery process and secondary gravity based chromite recovery circuits, but also because of intrinsic variations in the nature of the ore and its mineral composition. Variability in the ore, together with upstream process dynamics, creates a challenging environment in which to achieve optimal recovery of a gravity concentrate with accurate grade control. This paper examines certain inter-relational aspects between the ore gangue and chromite mineral types, the influence of the primary PGM extraction circuit and secondary chromite extraction activity as applied specifically to UG2 ore against a background of actual plant experiences and circuit configurations applied in order achieve a suitable quality of chromite concentrate.

Jan 1, 2010

Exxaro installed their first ultra fines treatment plant at Leeuwpan Coal mine. The plant is now fully operational and results already show that the plant has great potential. The plant was designed and installed by DRA. Several challenges were faced during the installation due to the space constraints in the Leeuwpan plant. Efficiency tests were conducted on both modules after commissioning and showed very promising results. A lower ash product with a higher yield can be produced with the fine coal dense medium cyclones compared to the spirals previously employed.

Jan 1, 2010

By S. Mohanta, I. D. Behera, B. Sahoo

"Run-of-mine coal contains particles of different sizes with different specific gravities, and when this coal is crushed, the amount of material present in a particular density class changes. This alters the washability characteristics of the coal, which affects the quantity, quality, and separation efficiency of the gravity-based coal washing process. The degree of difficulty in washing a typical coal at a particular specific gravity depends mostly on the amount of material occurring within ±0.1 specific gravity range, which is known as ‘near-gravity material’ at that particular specific gravity of separation. In this paper, two numerical indices, namely ‘near-gravity material index’ and ‘index of washability’, are used to quantify the distribution of near-gravity material in different density classes and to evaluate the degree of difficulty involved in the washing process. The results of this preliminary investigation indicate the uniform distribution of near-gravity material in all density classes for finer size fractions, whereas for coarser size fractions more near-gravity material is present in the lower density classes, making the washing process more difficult at a lower specific gravity of separation. IntroductionThe prime objective of coal beneficiation is to remove physical impurities as effectively and economically as possible. The beneficiation process includes various operations on the asmined coal to make it more suitable for enduse application without destroying the physical identity of the coal. There are several coal beneficiation processes, but gravity-based separators remain the most efficient unit operation for removing the undesirable gangue material from run-of-mine coal. These separators exploit the difference in density between coal particles and gangue particles to effect a separation. The feed is introduced into an aqueous suspension of ultrafine magnetite with a particular density. The feed particles with a relative density less than that of the suspension (clean coal) float to the top surface of the suspension, whereas particles denser than the suspension density (gangue material) sink to the bottom. When the difference in density between the particle and the aqueous suspension is large, the separation is easy, but when this difference is less the separation becomes much more difficult since the settling velocity of the particles is very low. This lower settling velocity increases the probability that particles that should report to floats report to sinks, and vice versa, hence increasing the amount of misplaced material. Therefore, the degree of difficulty in beneficiating a typical coal at a particular specific gravity depends on the amount of material occurring within ±0.1 specific gravity range. This is known as ‘neargravity’ material, also termed ‘near-dense’ material, at that particular specific gravity of separation."

Jan 1, 2016

By B. McFadzean, N. Patterson, M. Becker, S. Geldenhuys

The retreatment of secondary tailings for platinum group metals recovery presents a range of potential challenges, which vary depending on the nature of the original ore and the type of pretreatment it was subjected to. These challenges include the prevalence of ultrafine particles, which promote slimes coatings on valuable minerals, hinder bubble-particle attachment, increase pulp viscosity, and lead to higher gangue entrainment; surface oxidation of minerals, which alters their floatability; and the presence of deleterious gangue minerals and residual platinum group metal species that are inherently difficult to recover by flotation. This study compares the batch flotation performance across a range of tailings samples from the eastern and western limbs of the Bushveld Complex. A complementary mineralogical analysis was conducted to gain deeper insights into mineral behaviour. The paper evaluates these findings to identify the key factors contributing to poor platinum group metal performance.

Mar 6, 2026

By J. Hadjigeorgiou, G. Knox

There is a considerable wealth of information on the behaviour of rockbolts under axial loading conditions both in situ and under controlled laboratory conditions. However, there is comparably less data on the behaviour of rockbolts in shear. Several authors have contributed to the understanding of the behaviour of conventional rockbolts’ performance under shear loading. Much of this data have been gathered through experimental programmes conducted on sections of the rockbolt. Considering the continuous coupling between the rockbolt and borehole interface, the approach is justified. Due to the design premise of energy-absorbing rockbolts with discrete couplings, full scale testing is required to quantify the behaviour of the rockbolts. This paper reviews published results obtained from two testing facilities, which are the SINTEF rockbolt pull test rig in Trondheim, Norway and the Epiroc Combinations Shear and Tensile test rig in Johannesburg, South Africa, both capable of conducting full scale testing of rockbolts. Based on this high-quality database it was possible to identify three distinct responses of rockbolts in shear. The behaviour under load is controlled by the presence or absence of an encapsulation medium (resin/cement grout), the reinforcement mechanism, and whether the rockbolt is continuously or discretely captured. As a reference the results are compared to the performance in shear of conventional grouted rockbolts.

Nov 24, 2025