Search Documents

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

This Bureau of Mines report reviews the information presented at the Sixth Mineral Waste Utilization Symposium cosponsored by the Bureau of Mines, U.S. Department of the Interior, and the IIT Research Institute. Environmental scientists and engineers from nine countries participated in the symposium, which was held May 2-3, 1978, at the Chicago campus of IIT Research Institute. The 56 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial wastes, and scrap metal are summarized herein.

Jan 1, 1980

This study was done to evaluate the economic and technical considerations of using pozzolanic materials in order to guide cement manufacturers, pozzolan producers, contractors, Government organizations, and others interested in concrete construction work. Five hundred and thirty-eight samples of pozzolanic raw materials were taken from 27 central and western States. These samples were evaluated by petrographic procedures, and about 200 of the most promising ones were given a complete series of physical tests (American Society for Testing and Materials) to evaluate further their suitability as a pozzolan. This investigation showed that deposits of natural pozzolan materials were widely dispersed in the central and western parts of the United States but that exploiting these deposits would depend on whether they could compete economically with an increasingly abundant industrial waste product--fly ash.

Jan 1, 1969

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots.The four rounds were the standard 26-hole test rounds designed to break 4 feet of rock. The procedure for drilling and blasting these rounds is described in Report of Investigations 3509.Before the regular test rounds were blasted, about 1,200 bounds of fine rock was placed on the steel mucking sheets that covered the end of the adit track; the wails, hack, and floor of the adit were washed thoroughly; and the fine rock on the mucking sheets was completely wetted.Each of the 5 bomb shots consisted of 10 sticks of dynamite tied together and hung at midpoint of the adit, 8 feet from the fall."

Dec 1, 1942

By A. L. Engel

[Thi;. re:9ort presents re3ults of investigations of problema a3signed as ore-testing projects to the Ore-Dressing Section, t.fetal1urgica.l Div:biion, of the Bureau of Ii.fines at the .fississippi?Valley E>"'1lcrimcnt Station in rtolla, Ho., durine the fiscal year ended June 30, 1940.]

Jan 1, 1941

By A. L. Engel

[This report presents results of investigations of problems assigned as ore-testing projects to the Ore-Dressing Section, Metallurgical Division, of the Bureau of Mines at the Mississippi Valley Experiment Station in Rolla, Mo., during the fiscal year ended June 30, 1940.]

Jan 1, 1941

By L. C. IlsLey

The theory and practice followed by the Bureau of Mines in investigating electrical equipment4/ made for service in gassy mines are of particular interest not only to manufacturers but also to those organizations that deal with safety anal inspection at the mines. This publication purposes to discuss the theory upon which tests of equipment in explosive atmospheres are based and to consider inspection and other matters pertaining to investigations made by the Bureau in ascertaining whether a machine merits approval. The material in this report is taken from an earlier bulletin,5/ which is row out of print, and has been revised and brought up to date to make the information again available to manufacturers, inspectors, and others interested in the development of safe equipment.

Jan 1, 1954

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the quantitative procedures that have been developed for the mine-specific analyses of accident/injury experience data are presented and their applications are demonstrated in a summary form through case study examples. The quantitative procedures will aid mine safety management personnel to develop focused accident prevention strategies including training, as well as to justify the investment in such proactive programs through cost-benefit analyses.

Jan 1, 1993

By Jay C. Hanson

Various electrical and electromagnetic (EM) geophysical techniques are currently being evaluated by the U.S. Bureau of Mines for their effectiveness in the detection and monitoring of electrically conductive (1 to 5 S/m) lixiviant (leach solution) to depths of 600 m, either above or below the water table. These techniques include magnetotellurics (MT) , controlled source audiofrequency magnetotellurics (CSAMT), resistivity and focused resistivity, ground-penetrating radar (GPR), frequency-domain electromagnetics (FEM), and time-domain electromagnetics (TEM). Of these techniques, TEM may be the most effective, but CSAMT and focused resistivity also hold promise. Geophysical computer modeling of the borehole TEM technique was conducted based on an idealized geoelectric section (layered earth) with characteristics based on the Santa Cruz porphyry copper deposit near Cas a Grande, AZ. Layer resistivities and thicknesses were obtained from geophysical data and geologic logs available from the site. Modeling of borehole TEM in both preleach and during leach situations was conducted. Simulating the TEM method using computer modeling proved to be encouraging since there were substantial differences between leached and nonleached responses. The modeling does not prove the effectiveness of TEM in the field, but does indicate that detection of deep lixiviant zones is theoretically possible.

Jan 1, 1992

Confidence in the strength of the U.S. economic recovery was considerably enhanced by third quarter 1983 profits, which showed a 12.8-percent increase over those in the second quarter (table I). Although the increases were not as great as between the first and second quarter of 1983, profits have grown each quarter since fourth quarter 1982. Both total profits and profits per unit of output increased, which the Bureau of Economic Analysis (BEA) attributes to decreases in labor and nonlabor costs (per unit of output), as well as to moderate price increases. [ ] A number of durable goods sectors, however, continue to show profit declines, especially electrical and non-electrical machinery. Profits in the primary metal industry are still negative, but the economic picture of this industry is improving. Between the second and third quarters of 1983, capacity utilization increased somewhat in primary metal manufacturing and stone and earth mineral mining but did not change at all in metal mining. Capacity utilization in metal materials increased from 47.4 percent in the fourth quarter of 1982 to 64.2 percent in the third quarter of 1983 (table 2).

Jan 1, 1983

By William W. Adams

Progress made by the quarrying and related industries of the United States during 1939 included increases in the number of men employed and the number of man-hours worked and reductions in the death and injury rates per million man-hours of exposure to risk. Forty-seven States reported quarries in operation; in each of 26 States the industry employed 1,000 or more men. Of these 26 States, 16 reported lower accident rates than in 1938. Among the operations of various types for which separate figures are published in this bulletin, the limestone, lime, and cement groups reported lower accident rates. During 1939, 79,449 men were employed in the quarrying industries. The period of operation of the plants averaged 236 clays per employee, with a total working time that equaled nearly 144 million man-hours. Accidents at the plants resulted in 48 deaths and 5,204 disabling injuries among the workers. Expressed as frequency rates, the accidents represented 0.33 fatality and 36.18 injuries for each million man-hours of work performed during the year. The major cause of fatal accidents inside the quarries was falls or slides of rock or overburden; nine deaths were reported from this cause. Four men were killed by explosives and four by falls of persons. Nonfatal injuries inside the quarries were clue chiefly to handling materials; about one-sixth of the total number at all operations in connection with quarries and related plants were in this class. Flying objects also caused numerous injuries, although only about one-half as many as did handling materials. Next in numerical importance were injuries from falls of persons. Then followed accidents caused by falls or slides of rock or overburden and accidents caused by machinery.

Jan 1, 1941

By A. M. Poston

Introduction of radioactive elements into ore samples and/or pregnant liquors and radiometric tracing thereof have greatly improved control of fusion and extraction studies on beryllium ores and products. Extractive metallurgical research on beryllium, normally guided by the usual laborious analytical methods, is both costly and slow. Recognition of this problem by the Bureau of Mines led to the development and application of radioisotope tracer techniques" as a substitute for chemical analysis at the Salt Lake City Metallurgy Research Center, The result was that much faster progress at significantly lower cost was achieved. This report discusses the problems encountered and resolved in using radioactive tracers and radiometric methods, defines the conditions and techniques for their effective use, and delineates the limitations and flexibility inherent in applying such methods in laboratory-scale beryllium research.

Jan 1, 1962

By P. R. Jones

A computer program was written for design and cost of a shell and tube heat exchanger in which the total cost, which includes annual fixed charges and annual operating costs, was minimized. The program was written for the type of heat exchanger in which only the tube side pumping costs were significant and for triangular pitch, single or multiple pass, heating or cooling, and no change in phase. Tube diameter was not optimized since the tube dimensions do not affect the cost very much. However, the tube dimensions do affect the shell diameter, number of tubes, and length of tubes; and price optimum design was obtained for four standard tube diameters. Standard heat exchangers having at least the required area are also listed. The program was made adaptable to various fluids and to various tube dimensions by including many of the required data such as physical properties of the fluids, tube data, and standard shell data as input data.

Jan 1, 1969

By Joseph H. Bilbrey

COBALT is a silvery gray metal which closely resembles nickel in appearance and properties although it is somewhat harder and more brittle. It is rather widely disseminated and is estimated to make up about 0.001 percent of the earth's crust as compared to 0.020 percent for nickel. Cobalt, one of the four ferromagnetic elements, is used for many magnetic applications. It is oxidation resistant, a property which when coupled with its moderately high melting point of 1,495° C., makes it useful in high-temperature applications. Although cobalt had been used by man as a coloring agent for glass and other ceramic products for 4,000 years, it was not isolated as a metal until 1742 and not established as an element until some 40 years later. Early in the 20th century, cobalt began to be used in alloys, and soon these applications displaced ceramics as the major consumer of cobalt. The use of cobalt in alloys gave considerable stimulus to production, and the world output of cobalt increased rapidly, rising from 400 tons in 1920 to 1,400 tons in 1930 and 5,500 tons in 1940. With the advent of the jet plane in the mid 1940's and the consequent increased need for cobalt-bearing high-temperature alloys, cobalt production again increased, reaching 7,900 tons in 1950. The increased demand for cobalt during the Korean war coupled with a large demand for stockpiling caused world production to more than double within the next 10 years, reaching a peak of 17,300 tons in 1959.

Jan 1, 1962

By M. F. Boos

The Portland beryl-mica district, Middlesex County, Conn., comprises three deposits investigated by the Bureau of Mines in 1943. The Gotta-Walden deposit is in a pegmatite dike 4 to 20 feet thick, which cuts gneiss and schist. In general, the hanging wall is rich in mica and beryl with some feldspar, quartz, and garnet. The central core is usually high in quartz and feldspar, with relatively little mica and beryl. The footwall comprises quartz and feldspar, with varying amounts of mica and some beryl. The beryl crystals range in color from green to almost golden and have a maximum diameter of inches. Results of surface trenches indicate a beryl content of 0.81 percent for the pegmatite. A small production of beryl, feldspar, and scrap mica has been made from the deposit.

Jan 1, 1949

The Bureau of Mines analyzed the cycle of secondary gold to determine the quantity of gold not being recovered from scrap, and to identify areas for research to increase the supply of gold from scrap. Secondary gold in 1967 was estimated to be 2.4 million troy ounces; this excludes secondary gold which is recycled within consuming plants. Firms contacted included consumers using about 41 percent of the gold in 1967, And refiners that recovered about 90 percent of the secondary gold. Results of the study indicate that loss of gold is small, and refiners and consumers are accelerating programs designed to reduce recovery costs. With the increasing generation of low-grade industrial scrap, research is needed to improve present recovery techniques and to develop methods to accelerate the flow of secondary gold back to supply.

Jan 1, 1970

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934