Search Documents

By Terry J. Close

The highly-mineralized 43,700-ha Rapid River study area, on the southeast side of Hells Canyon Wilderness and west of the village of Cuprum, in Adams County, western-Idaho, was investigated in 1992 by the USBM (U.S. Bureau of Mines) in conjunction with its Idaho Land Assessment Program. The 1992 study updated data gathered during the USBM's 1974-76 Wilderness investigation. The studies consisted of the evaluation of 61 mineralized sites and the estimations of tonnages, grades, and minability of these sites. Most of the sites studied are in two mineralized locales--Windy Ridge and Jackley Mountain. A few isolated sites, peripheral to the two locales, were also examined. The 61 sites contained more than 340 mine and prospect workings, including about 10,300 meters (34,000 feet) of underground workings, plus 134 drill holes.

Jan 1, 1993

By Dennis A. Long

Slip and fall accidents are a major cause of lost-time injuries associated with large mobile equipment in surface mines. An evaluation of the safety hazards associated with getting on and off large surface mining vehicles showed that most of the accidents occur at the point where personnel attempt to mount or dismount the machine at ground level. The major hazardous design conditions were identified as excessively flexible supports for lower steps or rungs, inappropriate ground-level-to-first-step distances, poor step designs, access designs that use vehicle components as steps or walkways, and inadequate hand- rail and guardrail designs, Additional hazards are introduced by the lack of proper maintenance of ladder hardware and the work practices of operators in carrying articles while mounting and dismounting the vehicle. This Bureau of Mines report describes the design and in-mine testing of improved access system for large mobile mining equipment.

Jan 1, 1984

By R. H. Jefferson

This Bureau of Mines report describes a series of rapid wet chemical methods for the analysis of blast furnace slags. A "complete" analysis for total iron, manganese, silica, lime (calcium oxide), magnesia (magnesium oxide), sulfur, and mixed oxides (R203) can be routinely performed in less than 3 hours. These methods were employed as the analytical control procedures for the Bureau's experimental blast furnace operations and have been satisfactorily applied to the analysis of other slags and calcareous materials.

Jan 1, 1974

By Russell R. Trengove

Core samples from an ore horizon 2,000 feet below the surface were successfully obtained by rotary drilling at the property of the Eureka Corp., Eureka, Nev. The ore was soft and friable; cores were not obtained previously with diamond drills. Whipstocking was used to get samples in a zone 200 feet from a vertical hole. A technique in shipstocking, by which the direction and deviation of the holes were controlled by means of nonfriction-type survey instruments, was successfully employed.

Jan 1, 1956

Validate the premise that there is measurable seismic activity associated with abandoned mint lands and that this activity can be used to determine stability of the abandoned mine openings, failure cycle of these openings, and susceptibility of the area to surface subsidence. Approach The U.S. Bureau of Mines conducted field investigations at two geologically contrasting sites, Colorado Springs, CO, and the Allegheny Portage Railroad Historical Site near Cresson, PA, to demonstrate that developing monitoring technology can be applied to any site. An array of seven geophones (velocity-measuring sensors) were strategically located to encompass an area at each site where failure in the underground mine openings could be expected, based on historical, geological, and engineering information. How It Works Bureau research has effectively demonstrated that stress changes within a rock mass can stimulate the development of cracks and fractures, resulting in the release of strain energy that generates seismic waves. These seismic waves, traveling outward from their source, can be detected, and the point of origin can be located in three-dimensional space. Furthermore, these seismic signals contain information that defines the source mechanism and the conditions between the source and the receiving sensor.

Jan 1, 1992

By F. S. Crawford

This study was made to find methods of preventing back strains, among workers in brick plants, however, the information should apply to other industries that employ hand labor too process materials. The report is based on information in letters from. Bureau of Mines engineers and other safety men in the United States who visited numerous brick plants. Back strains, as wall as hernias and other muscular strains, result when certain body structures are subjected to strains greater than, they can withstand. Such breakdowns may be prevented simply by not straining these body structures. This is simple in theory but complicated in practice. It requires primary education of new workers and reeducation of older workers in the best method of lifting, preemployment physical. examinations to select employees for the jobs that require constant lifting, all possible mechanization of material-handling operations, relocation of machinery, and elevation of working surfaces to reduce to a minimum the muscular effort the workers must exert to perform operations impossible to mechanize. Accidents of any kind are a total bee for the American economy and decrease productivity; whereas mechanization raises the level of productivity and constitutes progress toward total safety. Heavy lifting should be done mechanically whenever possible, saving the men to direct the machines. This is an essential step in preventing strain accidents.

Jan 1, 1953

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines describing mining methods and performance at individual operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. SUMMARY Operation of a limestone quarry producing flux for the steel industry and crushed stone for production of concrete is described in this report. The deposit being mined is a flat-lying limestone formation under a thin overburden 2 to 25 feet thick. The height of the quarry face varies from 9 to 60 feet, averaging 40 feet. Production rate ranges from 4.5 to 5 million long tons per year.

Jan 1, 1959

By A. F. Jolly

In an effort to better predict the useful service life of friction rock stabilizer mine roof bolts in coal mine environments, the Bureau of Mines has evaluated the corrosion resistance of stabilizer steels in air-saturated and deaerated waters from seven Eastern and Midwestern underground coal mines. Accelerated electrochemical corrosion tests were used to estimate corrosion rates for the two high-strength, low-alloy (HSLA) steels used to fabricate Split Set stabilizers and for galvanized steel. Long-term static-immersion weight-loss tests were also conducted with the HSLA steels. Corrosion rates developed from the weight-loss tests (steady-state air dissolution) were roughly comparable to rates determined from electro-chemical testing in aerated waters. Although the highest rates occurred in waters with the highest chloride contents, rates in the other waters were low (<2.0 mpy) and exhibited little correlation to the widely varied chloride contents of the waters. The generally low corrosion rates are attributed in part to the tendency to deposit a protective CaC03 film, reflecting susceptibility to carbonate precipitation as indicated by positive Langelier (saturation) index values for the waters. With one exception, corrosion rates for the galvanized steel were (2.0 mpy. Rates with aerated waters were higher than those with deaerated waters. Pitting tendencies of the steels were also estimated.

Jan 1, 1987

By R. A. Pallanch

This paper, which describes the milling practice at the Midvale concentrator, is one of a series being prepared by the Bureau of Mines. The Midvale concentrator, a custom lead-zinc selective flotation plant, is in Salt Lake County, Utah, on a flat site several hundred yards east of the Jordan River and about 200 yards south of the Denver & Rio Grande Western Railroad tracks leading to Bingham Canyon. The site is at an elevation of about 50 feet above the river, the highest available location, thus allowing maximum storage of tailings.

Jan 1, 1931

Establish a procedure for reliably determining cation exchange parameters at an in situ mining site. The Problem Predicting the movement rates of pollutants from waste disposal sites requires reliable measurements of cation exchange parameters since cation exchange can retard pollutant movement. Reliable measurements of these parameters are also required for predicting the length of time needed to restore groundwater quality after in situ mining. Cation exchange is otten the controlling mechanism for the replacement of leach solution cations by the cations in the returning ground-water. Unfortunately, laboratory measurements using core samples are of minimal reliability. The uneven clay distribution at most sites produces a high variability in laboratory results. In addition the flow pattern in the laboratory tests is different from that in the field. Approach Bureau of Mines research has developed a field-test procedure that is quick and yields reliable and representative data. A corresponding data analysis procedure was also established in order to verify the&apos; applicability of the computer simulation model of cation exchange used in the analysis, and of the general analysis procedure, with actual field data.

Jan 1, 1986

The Technology Transfer Seminar on Mine Communications held on March 21-77, 1973, at the Pittsburgh Mining and Safety Research Center, Bruceton, Pa., presented information about recently developed equipment, instruments, and techniques for use in mine communications systems. All of the basic ideas presented in the fine seminar are operational in the Bureau of Mines Safety Research Mine in Bruceton.

Jan 1, 1974

By M. J. Pazuchanics

This U.S. Bureau of Mines report presents results from an ongoing investigation of the use of adaptive signal discriminating methods to distinguish between cutting coal and cutting mine rock. Bit-cutting forces and tool vibration were measured in the laboratory as a linear-cutting apparatus (LCA) made constant-depth cuts in coal, sandstone, and shale test specimens. A portion of the collected data has been analyzed and some preliminary results are given here. The influence of data bandwidth, data window size, number of signal features, and voting among classifiers on classification performance are noted. Results to date, based on ideal-cutting conditions and simple geologic materials, indicate that of the four classifiers tested there appears to be no single best classifier. Usually, classification accuracy showed slight improvement as the number of features considered for classification increased. The highest classification accuracies were achieved when voting was conducted among classifiers followed by voting among force components.

Jan 1, 1991

By D. Bienstock

The Fischer-Tropsch synthesis is practicable in a reactor where the exothermic heat of reaction is removed by circulating large quantities of recycle gas through a catalyst bed of high-voids content. At an hourly space velocity of 1100, the feed gas, a mixture of 1.5 parts hydrogen to 1 of carbon monoxide, was converted 90 percent, producing hydrocarbons predominantly in the gasoline range. At these conditions a recycle-to-fresh gas ratio of 40:1 was enough to give excellent temperature control with a pressure drop of 1.5 p.s.i. per foot of bed using a steel catalyst in the form of lathe turnings. Steel parallel plates, although offering lower resistance to gasflow, were less reactive and less durable. INTRODUCTION The Federal Bureau of Mines has been engaged in a research and development program since 1944 on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a synthesis gas--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va.; and the synthesis of gasoline by catalytically reacting the carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960

By W. Ayvazoglou

A large number of organizations interested in the search for mineral deposits have adopted the magnetic method of geophysical prospecting, as it has proved to be the most simple, convenient, and rapid, and at the same time the least expensive in comparison with other methods. According to the last statistical data, about two millions square kilo¬ meters were explored in the United States by different geophysical methods. Ninety-six per cent of this area was prospected for oil and 4 per cent for minerals. Detailed exploration by means of the magnetometer has been carried out over about 85 per cent of this surface. The great advantages offered by this method resulted in the fact that the magnetometer was tried out in most places in which geophysical methods were applied. The main purpose of such e:rploration is to obtain the maximum knowledge valuable to the geologist; therefore good geological interpretation of the results of measurements is important. The possibility of drawing practical conclusions from a map representing the results of the study of the terrane depends greatly on the accuracy with which the measurements are made. The purpose of this article is to show the different sources of error by which the work of an operator may be affected and to discuss the means by which the carrying out of a magnetic survey may be improved.

Nov 1, 1931

By L. D. Wyant

[A convenient method for the, analysis of oil-wax mixtures has bean developed in the petroleum laboratory of the Bureau of Mines. This method has been found useful in studying the characteristics of the products obtained in petroleum refineries during the manufacture of ?wax distillate?, "foots oil", ?intermediate wax", and commercial paraffin. In this method ac-to-au is used as a selective solvent.]

Jan 1, 1924

By A. Visnapuu

The U.S. Bureau of Mines investigated the oxidation of American Iron and Steel Institute (AISI) Type 304 stainless steel (SS) during annealing in simulated combustion products from several air-CH4 fuel ratios. Atmospheres representing air-CH4 ratios of 14:1 and 18:1 contained free 02, while atmospheres representing 10:1 air-CH, ratio did not. A Cr203 layer formed on SS samples annealed in atmospheres containing free 0, while a Cr-Fe spinel layer formed in atmospheres with no free 02. The Cr203 layer was adherent and presented a protective barrier to metal diffusion, effectively limiting oxidation of the metal substrate. The Cr-Fe spinel was not protective and allowed the diffusion of Fe through the spinel to the gas-oxide interface where it was oxidized to magnetite, which spalled from the surface. This resulted in thick scale layers on samples annealed in atmospheres containing no free 02, as compared to layers formed on samples annealed in atmospheres containing free 02. These results confirmed and explained industrial operators&apos; observations that thick, smoky (fine spalled magnetite) scales form on SS annealed in low free-02 atmospheres, while thin protective oxide layers form on sheets in atmospheres containing free 02.

Jan 1, 2010

The first phase of our work for PMSRC on this contract was devoted to a comprehensive and in-depth assessment of electromagnetic (EM) noise measurements and data taken by several contractors for use in the design of operational and emergency mine communications. Pertinent measurements and data of other selected investigators were also included in the evaluation. This assessment treated the measurements and instrumentation used, the data analysis and presentation methods, and the utility of the final results. This phase concluded with the identification of the most useful results and methods, the remaining data gaps, the contractor most qualified to fill these data gaps, and the definition (with PMSRC and this contractor - NBS, National Bureau of Standards) of a follow-on noise measurement program, instrumentation system, and data processing methods tailored to obtain the necessary but missing noise data. A partial bibliography of references related to electromagnetic and seismic noise and propagation in the frequency bands of interest was also compiled during this first phase. The body of this Part of the final report presents a summary of the findings of our EM noise assessment, together with detailed recommendations regarding the new noise measurements to be taken and the instrumentation and data processing methods to be used. This work was done during the latter part of 1971 and the early part of 1972. During subsequent phases of the contract ADL was asked to perform on-going evaluations of the continuing program of electromagnetic (EM) noise and propagation measurements made by Bureau contractors, and to utilize pertinent data from these measurements to make performance estimates for

Jan 1, 1974

By L. W. Kelly

The purpose of this circular is to show that, under the conditions prevailing in the Stony Point mine, wooden bolts were just as satisfactory as steel bolts or conventional timbering, with a reduction of approximately 80 percent in cost of material. This one fact alone is enough to justify an experiment with wood. This circular will show that production records have remained constant with both wooden and steel roof bolts. INTRODUCTION The successful use of steel roof bolts is now an accomplished fact in the coal industry, but the use of wooden bolts in place of steel is a rarity. The first experiment with wooden roof bolts was mane in 1949 in the Rio Verde mine, Norton Coal Corp., Nortonville, Ky.2/ This experiment was successful; the company obtained excellent results, but operations in the mine were suspended before enough time had elapsed to prove the value of wooden roof bolts conclusively. It is obvious that, if wooden roof bolts could be used in place of steel bolts or conventional timbering-methods, every mine operator would use word, as the cost is only a fraction of the other two methods. The Stony Point experience has proved conclusively that, under certain conditions and with a certain type of roof, wooden roof bolts can be used successfully.

Jan 1, 1952

By L. H. Wullstein

Bureau of Mines research on methods for reclaiming land disturbed by the minerals sector of the economy has produced a specific procedure for effectively germinating seed of Indian ricegrass, a drought-tolerant plant valuable for reclaiming arid and semiarid sites. This report describes the procedure which consists of acid-treating the seed followed by temperature and light cycling treatments. Use of the procedure resulted in an average germination rate of 29 percent, ranging from 18 to 56 percent. Seed subjected to long cold treatment but with acid treatment yielded an average germination rate of 9.2 percent, ranging from 6.6 to 14.7 percent. Untreated seeds (controls) gave germination rates less than 0.1 percent.

Jan 1, 1979

Mining and reclamation procedures that meet the requirements of SMCRA are illustrated on pages 8 and 9 for each of the three major surface coal mining methods -- area mining, contour mining, and mountaintop removal mining. The three methods involve the same basic steps: clearing the land of trees and other vegetation, removing topsoil and overburden, mining the coal, and reclaiming the land. Although all three methods would not usually occur on any single site, the illustration facilitates comparison of mining and reclamation methods and aids basic understanding of the reclamation processes that take place under SMCRA. Area Mining The area mining method is commonly used to mine coal in the flat to moderately rolling terrain found principally in the western and midwestern states. After the overburden is excavated down to a coal seam, the mining area is enlarged horizontally to expose more coal for removal. In the West, where coal seams are commonly 10 to 20 feet thick (and range up to 100 feet thick in the Powder River Basin of Wyoming), the life of some mines maybe more than 50 years. In the Midwest, coal seams are typically 3 to 7 feet thick and 75 to 100 feet below the surface. Because of the large expanse of area mines and their relatively unrestricted sites, enormous equipment is used to remove overburden and reconstruct the land. The area mining operation in the illustration is on land that was formerly used for farming. The drawing shows that the agricultural use is being reestablished immediately following reclamation. Mining is proceeding across the land toward the left side of the site. The initial excavation was made far enough away from the stream along the right edge of the site to prevent damage to the water supply. The coal under most of the site has been removed, and reclamation has been completed on some of the land. For example, some of the cattle in the foreground and those in the feedlot behind the silo are grazing on reclaimed land that has been mined. At the far left of the illustration, topsoil from the unmined area is being removed by scrapers, transported across the area of active mining, and immediately spread on the land on the right, which is being reclaimed. (Reclamation of mined land as soon as practical, as required by the Act, is called contemporaneous reclamation.) A

Jan 1, 1992