Search Documents

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By Donald C. Strimbeck

The Bureau of Mines designed a down-fired refractory-lined combustor that efficiently burned pulverized coal to produce a gas suitable as working fluid for an open-cycle gas turbine. The gas contained relatively little carbon, so the load on the ash-separation equipment was significantly reduced. Moreover, reduction in carbon content of the gas increased the average density of the solid particles making them more amenable to removal by centrifugation. Centrifugal-type separators failed to remove sufficient ash; however, to limit blade wear enough to achieve operating periods generally deemed necessary for commercial practicability.

Jan 1, 1969

By S. K. Ash

In arriving at economic losses in coal mining due to accidents, a statistician is confronted with many difficulties on account of the lack of information relative to nonfatal accidents. For comparative purposes the ex¬ perience of those countries, States, or companies that keep complete records can be drawn upon and an extimate can be arrived at whereby one State can be compared with another, or one mine compared with another in the same district. Such a comparison for the United States has been compiled by the United States Bureau of Mines. It will be observed in Table 1 that the cost per ton for accidents in the State of Washington for the year 1927 is higher than for any other State, with the exception of Georgia and North Carolina, with a small combined tonnage of 130,089 tons. (The figures for coal production in Table 1 are taken from Bulletin 319, 1930, of the United States Bureau of Mines.) The reasons why the cost of accidents in Washington might be higher than the average are on account of physical conditions such as steep pitches, faults, igneous intrusions, highly explosive coal-dust, extremely friable coals, presence of gravel and water, very gassy coal beds, rugged topographic conditions, inherently bad roof and floor, thick beds, and heavy cover. The nature of the coal beds requires the use of preparation machinery. The mines are often deep, and topographic conditions are such that long and fast haul¬ age becomes necessary. All of these factors not only tend to cause high cost of production, which is manifested largely in a. lower than average daily pro¬ duction, per man, but..they.also affect to some degree a tendency toward a higher than average cost for accidents.

Nov 1, 1931

By R. S. McClain

The Federal Bureau of Mines investigated residues from aluminum plants, to determine if carbon could be removed by flotation while recovering fluorine and aluminum compounds for recycling to the reduction process. This publication summarizes studies on samples representing three types of plant waste products, supplied by three aluminum-producing companies. Samples of flue dust, pot skimmings, and pot linings from the various plants all responded to a simple turpentine flotation scheme to reject 90 to 97 percent of the carbon. Aluminum compound recoveries ranged from 42 to 94 percent on the flue dust, were about 95 percent on the pot skimmings, and ranged from 75 to 89 percent on the pot linings. Fluorine recoveries from the same samples ranged from 35 to 63, 92 to 95, and 77 to 86 percent, respectively. The pot linings contained soluble salts of aluminum and fluorine which were recovered by precipitation with sodium aluminate and carbon dioxide gas. Composites of residues from each plant responded to flotation much the same as the individual samples. Aluminum is produced by the electrolysis of alumina in a molten cryolite bath. The electrolytic reduction cell consists of a carbon-lined box containing a pad of molten aluminum which serves as a cathode, a carbon anode, and an electrolyte of molten cryolite in which the alumina is dissolved. Alumina is reduced to aluminum at the cathode, and carbon is oxidized at the anode.

Jan 1, 1961

By Robert C. Weisner

Current production costs and market conditions in the potash industry of the Carlsbad area were studied to determine the potential values of the potash mineral resource that would be lost or foregone if the Waste Isolation Pilot Plant (WIPP) facility is constructed on the proposed site in that area. The purpose of the WIPP project is to investigate the possibility of developing a nuclear waste disposal plant in the salt formations at the site. Analyses were made of all potash deposits determined to be in the site. Mining and processing under the most favorable recovery systems were considered. Value determinations were based upon estimated operating and capital costs of current mine-mill operations in the Carlsbad area. This study was made for the Energy Research and Development Administration (ERDA) by members of the Federal Bureau of Mines Minerals Availability System staff.

Jan 1, 1979

By Oliver Bowles

ASBESTOS is a name applied to a group of naturally fibrous minerals. As indicated in a later section devoted to a detailed discussion of the early history of asbestos, the tern may be defined as a. fibrous form of serpentine or amphibole. It does not include fibrous forms of other minerals, such as wollastonite, nemalite (fibrous brucite), or the fibrous forms of calcite or gypsum. A material that has the characteristics of silk or cotton and at the same time will not burn is unique. Because it combines these qualities with other advantageous properties, asbestos has specialized uses for which no substitutes are yet available. Asbestos furnishes a major raw material for a great variety of essential products and their manufacture constitutes a vast industry. The United States leads all countries in the manufacture of asbestos products. The value of such commodities manufactured in 1952 exceeded $332 million. They are not only of vast importance to budding construction and industry but axe absolutely, essential to certain important fields of use, for example, steam packings and friction materials, such as brake-band linings on automobiles.

Jan 1, 1955

By Clifford B. Farris

The natural cementation strength of retorted oil shale is the focus of this investigation. The optimum retorting temperature and residence time to obtain natural cementation strength in retorted Green River oil shale from western Colorado were determined as follows: [Optimum Conditions for Natural Cementation Maximum Residence Obtained Retorting Time at Compressive Mode of Temperature Temperature Strength' Retorting °F °C hr psikg/cm-2 Direct 1,520 822 2.0 270 19.0 Indirect 1,530 832 2.9 325 22.8] 1 Scattered samples were tested at strengths as high as 463 psi (32.6 k /cm 2) (Run 8, indirect mode) and 406 psi (28.5 kg/cm2) (Run 48, direct mode), but these high strengths were not confirmed by nearby tests. Minus 0.5-inch (1.3-cm) Green River oil shale was heated in a differential retort under conditions simulating potential full-scale retorting processes. The variables investigated were retorting temperature, residence time, retorting mode, and shale grade. Samples of the retorted Green River oil shale were moistened to optimum plus 2% (25%) moisture, compacted to 95% Proctor density, sealed and cured at 100°F (38° C) for up to 40 days. Lower curing temperatures, which are likely in the field, would probably result in significantly slower development of cementation strength, and might lower the ultimate strength developed. However, these effects were not studied in this project. The cured samples were tested for compressive strength, and correlative equations were developed for the increase of compressive strength with curing time as a function of retorting temperatures and residence time. Petrographic analysis indicated that the cementing mechanisms may be the interlocking growth of acicular hydrated calcium aluminum sulfate crystals between the contacts of retorted shale fragments. Samples of the retorted shale were also tested for optimum Proctor density and moisture. Permeability and quality of the leachate of shale from typical runs were determined. The effect of use of retort rather than tap water on compressive strength and leachate after curing was determined. The retorted shale effectively filtered several mineral constituents from the retort water.

Jan 1, 1979

By Donald Christofferson

This report documents the program conducted to demonstrate the application of a flywheel-powered propulsion system to underground mining shuttle cars. Such application can replace the present electrical trailing cable common to most shuttle cars and thereby eliminate those safety hazards, maintenance problems, and haulage route limitations inherent in the trailing cable. Described are the activities undertaken to specify and design a flywheel of optimum size, shape, and material; to identify the best concepts of input and output systems; and to achieve installation of the power package into a shuttle car. The resultant Flywheel-Powered Shuttle Car is an FMC Model 6L shuttle car, 6-ton capacity, 20-ton gross vehicle weight, powered by a flywheel system with 4.5-kilowatt-hour usable energy. The completed vehicle was delivered to the Bureau of Mines in Bruceton, Pennsylvania, for testing and evaluation.

Jan 1, 1986

By J. P. McCullough

In 1943, the Federal Bureau of Mines began a program of thermodynamic investigations of petroleum constituents and related compounds. These systematic, long-range studies, which were conducted in the thermodynamics laboratory of the Bartlesville Petroleum Research Center and are still continuing, have resulted in a substantial quantity of data valuable to the petroleum industry and science in general. As separate phases of these studies were completed, the findings were promptly reported in the scientific press. During the past 16 years, 89 journal articles, giving the results obtained for individual compounds and small groups of related compounds, were published, mainly in the Journal of the American Chemical Society and the Journal of Physical Chemistry. In addition, members of the Bureau staff have contributed six chapters to specialized reference books. This circular, prepared in response to many requests, lists these 95 published papers, giving an abstract of the contents of each, as well as titles, authors, and literature citations. The journal articles are listed in the order of their preparation, which closely approximates the chronological order of their publication; hence, the item number to the left of each citation corresponds to the assigned contribution number. For the convenience of the reader, the abstract section is followed by a condensed bibliography, arranged alphabetically by senior author and keyed to the abstracts by appropriate contribution numbers in parentheses after the entry.

Jan 1, 1961

By R. H. Fernald, C. D. Smith

When the United States Geological Survey began operations at the coal-testing plant erected at the Louisiana Purchase Exposition at St. Louis, Mo., in 1904, it had already outlined a comprehensive plan for the systematic study of coals, lignites, and other mineral fuels with reference to their suitability for particular purposes and the methods by which they could be utilized most efficiently. Recognizing the need of information on the relative economy of producer gas as compared with steam for power purposes and the lack of comparable tests of American coals in the gas producer, the Geological Survey undertook investigations of the merits of different coals as producer fuel for the purpose of promoting efficiency in the utilization of the nation's fuel supplies. These investigations were carried on at St. Louis, Mo., and, later, at Norfolk, Va., and Pittsburg, Pa. The aet of Congress approved May 16, 1910, transferred the fueltesting work being carried on by the Geological Survey to the Bureau of Mines. This bureau is conducting producer-gas tests at P~ttsburg, Pa., and is publishing and distributing reports relating to all the fuel tests made by the Survey. These investigations into the possibility of generating producer gas in a commercial way for power purposes from the various fuels of the country have been associated with steaming, briquetting, coking, and other tests, all of which supplemented an examination into the nature, extent, and distribution of the fuels. The tests have all been made with carefully selected representative samples and carload lots of materials procured specially for the purpose by experienced collectors.

Jan 1, 1911

Watershed Jll in Jefferson County, Ohio we instrumented in 1977 as one of three watersheds established for the purpose of investigating surface mining and reclamation effects upon local hydrology, sediment discharge, and sediment and water quality. Each watershed was less than 50-acres in size, and was in a different geologic setting within southeastern Ohio. Surface runoff and ground¬water levels were monitored. Samples were taken for sediment determination and chemical analysis prior to mining. Monitoring and sampling continued through the period of watershed disturbance caused by mining and reclamation activities, which began in May 1980 at Watershed Jll. A psuedo-postreclamation period followed the initial cessation of man-machine activity on the watershed. A second reclamation effort occurred in the fall of 1981 and was to be followed by a third in 1982 after observations ceased. A true final postreclamation period was not monitored at this site, because the erosion control practice (terrace diversions) failed after each reclamation. Watershed Jll was a small pasture and wooded watershed with sandstone and shale above the mined coal seam prior to mining. A clay layer under the coal supported a perched saturated zone, termed the top aquifer for convenience. A lower underclay supported a second saturated zone called the middle aquifer. A lower perched aquifer had been dewatered by previous deep mining. After about three years of premine data and about two and one-half years of mining reclamation and psuedo-postreclamation data, the following general observations may be made: 1. The mining-reclamation phase was very short, and the postmining period was characterized by erosion failures and remedial disturbances that kept the watershed condition and size in a state of change. It was impossible to collect sufficient data to confidently characterize the hydrologic-sediment-chemical aspects of the mining period or of a postreclamation period and, most importantly, of the future watershed after its various properties and characteristics have ceased adjusting to its severe disturbance and reconstitution. 2. A seeding of wheat followed by grasses and legumes was not a particularly successful reclamation practice in terms of stabilizing the new soil. Numerous rills and small gullies developed in spite of installed diversions. 3. Storm runoff rates and yields at the watershed outlet increased from the premine, (phase 1) to the mining-reclamation (Phase 2) periods, and remained at or near the Phase 2 level through the postreclamation (Phase 3a) period. 4. The top aquifer changed in physical and chemical character as a result of mining and was becoming reestablished as the project drew to a close; but it is impossible to predict its final configuration or character. 5. Dewatering of the top aquifer resulted in a complete cessation of baseflow because the middle aquifer water table lay below the elevation of the watershed outlet. 6. The top and middle aquifers were merged in one area of the watershed where the upper coal underclay was disturbed. 7. Failure of the diversion terraces and their outlet obscured the effects of the reclamation practice upon sediment concentration and yields. There was little difference in sediment concentrations between Phases 2 and 3a. 8. Drinking water standards were met by surface waters throughout the period of observation except for two samples that exceeded the nitrate-N allowable level of 10 mg/l. 9. In all Phase 3 surface-water samples, iron concentrations were within the limits established by OSM, and manganese concentrations exceeded the regulation level only once. pH fell below the lower regulation level of 6.0 between 10% and 20% of the time. 10. The chemical quality of sediments was generally about the same after reclamation as before mining, with the exception of organic carbon, which decreased.

Jan 1, 1983

By D. Harrington

The primary objective of this paper is to discuss the hazards and furnish a list of recommendations for the safe operation of quarries and related works. They have been compiled from Bureau of Mines publications covering the safety experience of engineers before and during the year in the mineral industry,5 from a publication of the National Safety Council, Inc.,6 from explosives recommendations made by various explosives manufacturers,7 and from suggestions obtained from quarries visited. The second objective is to describe and illustrate safety devices, practices, and quarrying methods. The quarrying and related industries of the United States had a lower accident-frequency rate than either the metal- or coal-mining industry as reported for 1942.8 However, the quarry industry ranked eleventh in 15 major industries during 1942 in lost-time accident fre¬quency; metal mining ranked fourteenth and coal mining fifteenth.

Jan 1, 1950

By James Ridenour

This report represents the first comprehensive accounting of lode mining sites in the Loon Creek mining district, Custer County, Idaho. Thirty-five mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were field checked and the updated information added to the data base. The district's major deposits are gold-copper-silver fissure-fillings hosted by biotite schist intruded by dikes ranging in composition from rhyolite to lamprophyre. These deposits contain a trace element suite similar to Tertiary pink granites and may be related to intrusion of the nearby Casto pluton. Continued firm gold prices could stimulate the search for precious metal occurrences in this and other mining districts in central Idaho.

Jan 1, 1983

By Robert T. MacMillan

A process has been developed in the laboratory and expanded to semi-pilot-plant scale for recovering titania, iron, and byproducts from two types of titaniferous iron ores. A reducing roast with coke and soda ash followed by grinding and magnetic separation produced powdered iron and slag from which titania and byproducts were recovered by H2SO4 decomposition. Based on the steps tested on a. semi-pilot-plant scale supplemented by the results of the laboratory investigations, enough data are available to make a balanced flow sheet. Combined data from the laboratory and semi-pilot plant indicated that 85 to 9O percent of the titania content of the ore was recoverable and that approximately 90 percent of the iron could be recovered as a metallic-iron powder. Tahawus magnetite from the Maclntyre mine at Tahawus, N. Y., was successfully treated as follows: (1) The ore was roasted at 1,050° to 1,080° C. with carbon and soda ash, thereby reducing the iron to metal sponge and retaining the titania in the slag. (2) The metallic iron was separated, after wet grinding, by magnetic or gravity means. (3) The slag fraction was air-roasted at 850° C. and leached with NaOH to recover Na3VO4. (4) The leached solids received a dilute-H2SO4 leach to remove interfering impurities, chiefly Na2O and SiO2. (5) Titania was dissolved from the leached solids of step (4) by a H2SO4-bake followed by a water leach. (6) Titania was precipitated by seeding and boiling the resulting solution. The spent liquor was used for the dilute-H2SO4 leach in step (4). The following scheme was found to be technically feasible for recovering other byproducts of the process. (1) The gelled filtrate from the dilute-acid leach step was washed and dehydrated to produce a commercially acceptable silica gel. (2) The wash liquor containing sulfates of Na2O, Al2O3, Fe2O3, and TiO2 was combined with the highly alkaline filtrate from the wet-grind and metallic iron-separation steps, precipitating iron and titanium hydroxides, which were separated for special treatment. (3) Anhydrous Na2SO4 and Al2O3?3H2O were recoverable from the alkaline filtrate from step (2) by evaporation and carbonation, respectively, and the barren liquor was recycled to the magnetic-separation step.

Jan 1, 1952

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By R. H. Oitto

To determine whether reflectors could substitute for the trip lights referred to in the Federal Mine Safety Code, the Bureau of Mines studied trip safety devices under simulated haulageway conditions. The noticeability of reflectors compared with trip lights and fluorescent panels was evaluated from distances of up to 850 feet with light source intensities of up to 1-6 foot-candles (ft c). Reflectors tested consisted of a reflective lens in a holder secured to a frame that can be attached to a trip. Reflectors were found to be suitable for use as a trip safety device. In fact, for the conditions in many underground haulageways some reflectors would be more effective than a permissible trip light.

Jan 1, 1968

By H. B. Humphrey

[EXPLOSION of gas and dust in coal mines, have caused death t lid injure to mines, and destruction of workings in all countries where coal is mined underground. In the United Stales the first reported explosion wits in Min; explosions have continued to the present. The danger to film ill it mine When an explosion occurs in not always measured by the violence created or by their nevi lies, to the area through which flame and Violence extend. As many, perhaps more, risen have died from gases and lade of oxygen (known as "after-damp") than have been killed by the blast and hart. Me explosions often are caused by it combination of factors, including concentration of methane in air, formation of clouds of dust, and the presence of a flame or spark. These explosion factors have varied with changes ill milting method and practises over the years, but the basis causes have always been the salve. Understanding of the causes and to acceptance of ways to guard against explosions and their effects have been slow to spread from investigates to officials and Own to bosses and miners. To a considerable extent there hats lawn a belief that explosions were a joining risk but might hr, put oil hut could not be presented. Such belief is based on the human failure to maintain and observe necessary precautions. These failures, caused by inertia to change, carelessness, or reliance on continuance, of past explosion-free years, are being reduced in number and effect by education of miners and supervisors and acceptance of higher prevention standards.]

Jan 1, 1959

By D. Randolph Berry

This manual was prepared to provide essential information to be used when critical decisions pertaining to mine fire recovery or other disaster situations become necessary. It is a state of the art report based upon technology and instruments developed, under a Bureau of Mines Research Contract. A detailed description of the development work and results of full-scale field testing is contained in the Technical Report, Vol. II, of USBM Contract Report H0122045, "Extinguishing Coal Mine Fires by Remote Scaling." Further research and development work has been programmed; consequently, a more complete manual providing detailed instructions and describing available instruments and equipment will be published. Those instruments and special equipment described in this manual must be considered prototype; methodology and applied technology will require special expertise. Consequently, any prospective application of this remote sealing technique will require assistance by the United States Bureau of Mines Research organization and experts from the contractor who developed the basic technology and instruments.

Jan 1, 1973

By R. Lusignea

This report describes the development of a device for the nondestructive testing of resin grouted roof bolts by means of mechanical frequency response. Various alternative methods were evaluated and the mechanical frequency response method was selected. An interactive program of design, testing, and development culminating in the current prototype instrument demonstrated the capabilities of the method and suggested potential applications of the instrument. The resin bolt testing device utilizes a swept frequency dynamic compliance measurement in the 1 to 2 kHz range which is interpreted by an electronic signal processor to give a "GO" or "NO GO? readout. Field tests have shown that the device can reliably determine the bond quality of the front half of the bolt (nearest the roof surface). Tests were carried out on both experimentally installed bolts and typical mine bolts installed by a conventional bolting machine. The development program has led to recommendations for improvement of the prototype and future development work.

Jan 1, 1979

By Mark K. Larson

A constitutive model for rock interfaces based on the principles of static fatigue is proposed. The model is applicable to weak rock or joints with cohesion. Friction and dilation are decreased as plastic work increases. At equilibrium, the creep time increases by one time-step interval, and interface cohesion at each node decreases according to a power function. A constant-load, direct-shear simulation showed that the model is cap- able of mimicking constant-rate and tertiary creep and predicting failure. Tests on core from a coal mine showed constant-rate and, sometimes, tertiary creep, but also weak transitory creep. The cohesion deterioration function may need modification to simulate primary-phase creep. If model parameters are known for a site, the model can predict the onset of tertiary creep and failure. Such predictions can help engineers make better entry design and support decisions, which will reduce the likelihood of roof falls and increase safety for underground miners.