Search Documents

By David E. Swanson

The U.S. Bureau of Mines undertook a basic investigation of collimated abrasive water-jet behavior because a more complete understanding of the fundamental process may lead to further technical advances. Laboratory experiments used 2-mm water-jet nozzles and new entrainment apparatus to analyze collimated abrasive water jets operating under varied conditions. Maximum water pressure was 69 MPa to permit use of conventional hoses with a burst-to-operating-pressure ratio of 4. Nozzle and induction line pressures, abrasive induction rates, and jet reactive thrust forces were recorded for each operating condition. Average jet velocity and power were determined from component mass flow rates and reactive thrust force measurements. Relative velocity and cross-sectional distribution of abrasive particles were determined using impact analysis techniques. Other jet characteristics were determined photographically. Properties of free water jets, collimated water jets, and collimated air-water jets were determined for comparison.

Jan 1, 1989

By D. J. Singleton

Erosion corrosion of 12 alloys in phosphoric acid waste water was studied by the Bureau of Mines. Tests were conducted on oblate spheroids or cylindrical specimens in 12-and 60-cm-diam ball mills by grinding phosphate rock in gypsum pond water with a starting pH of 1.6. For comparison, tests were conducted while grinding phosphate rock in plain water. Static corrosion tests in gypsum pond water also were conducted. For all alloys, the wear by erosion-corrosion (milling with gypsum pond water) was greater than the sum of erosion (milling with water) plus static corrosion. Erosion-corrosion wear was about 1,500 to 3,000 mpy for the alloyed white cast irons, 1,000 to 1,400 mpy for commercial steel ball material and type 316 stainless steel, and 600 to 900 mpy for nickel-base alloys and a high-manganese, nitrided stainless steel. Alloy costs per unit of phosphate rock 'processed favor a low-alloy, high-carbon steel or a high-manganese, nitrided stainless steel.

Jan 1, 1985

By John C. Edwards

To increase the capability to predict the effectiveness of a flame arrester in the cooling of hot combustion gases expelled through a flame arrester, the U.S. Bureau of Mines developed an equilibrium. model and one-and three-dimensional transient thermal models of a flame arrester, which were used to predict the temperature evolution within the arrester and the maximum temperature at the external surface of the arrester. The models account for convective and conductive heat transport within the arrester and radiative losses at the exit surface. The gas flow through the arrester is established from an empirically derived relationship between the gas velocity and the pressure gradient across the arrester. Lateral heat loss from the arrester to the enclosure wall is accounted for in the three-dimensional model. The model calculations for maximum outside surface temperature of the arrester showed an approximate agreement with measured values for vent-area-to-enclosure-volume ratios between 12 and 28 in2?ft-3.

Jan 1, 2010

By Carl F. Wingquist

Electrical resistance heating to effect thermal fragmentation of semiconductive rock was examined by the Bureau of Mines. Tests were carried out on copper-bearing ores of the Nonesuch Shale Formation in the laboratory and in the the field at White Pine, Mich. Fieldwork included primary and secondary breakage tests. Heating tests on in situ rock failed to produce thermal dam-age to an extent considered useful; however, boulders up to 30 ft3 were effectively broken by the method. Power input to the test rock was taken from a 50-kV, 5-amp dc power supply.

Jan 1, 1976

By R. J. Gunderman

Redesigns of the operator compartments on a continuous miner and on a face haulage vehicle are described. The objective was to optimize the compartments within limitations of existing equipment and functional configurations. Both safety and production should be improved through more comfort for the operator and more natural placement of controls. Design guidelines supplied by the Bureau from a previous contract were used along with human factors analyses to determine requirements. Mock-ups were fabricated from layouts and used to refine design details. The new compartments were implemented and the machines evaluated underground. Comments and reactions to both machines were favorable.

Jan 1, 1978

By E. P. Youngman

Before the World War the use of zirconium and its compounds was largely experimental and confined almost wholly to Germany and Austria . Occasionally small lots of zirconium ore had been produced in the United States ( 1,000 pounds in 1869 , 26 tons in 1883 , and 3,000 pounds in 1903 ) and used (with monazite ) in the manufacture of various lighting devices , especially incandescent gas mantles ; but it was not until 1906 that the discovery of the natural zirconium oxide in large quantities near Sao Paulo , Brazil , first gave promise that a zirconium industry eventually might be developed . Edward Rietz , who worked the Brazilian deposits , interested German chemists in extending the use of zirconium , and by 1911 trade journals were listing German firms as manufacturers of compounds or products derived therefrom . For a time zirconia was one of the various oxides used in the Nernst lamp . It was used also for crucibles and hearths as refractory material ; in the manufacture of chemical utensils ; in enamels ; in the place of bismuth subnitrate for defining Röntgenray pictures of the stomach ; as a pigment ; in medicine ; and in a number of other ways . The Germans were credited also with producing a remarkable zirconium steel , which , it was claimed , was much superior to other alloy steels . During the World War the United States Government investigated the possibilities of zirconium , as well as those of other steel -hardening elements , and a large automobile manufacturer actually purchased a substantial quantity of ore with the purpose of employing zirconium in automobile steels . Immediately after the armistice the Government ceased its investigations ; but despite the difficulties experienced by various investigators in reaching concordant results , interest in the use of zirconium as a steel -hardening agent , as well as in other uses of the element and its compounds , continued . In 1918 the Foote Mineral Co. , which had been interested in zirconium for several years , was exploiting the deposit in Brazil formerly worked by the Germans and was supplying zirconia in the form of ore , brick , and cement for refractory and other purposes . About the same time the Electro Metallurgical Co. , which before the entrance of the United States into the war was experimenting with zirconium alloys , supplied in tonnage quantities the demand for these alloys . In 1919 it was reported that American manufacturers , after several years of research, were producing in commercial quantities pure zirconium oxide , which was finding a place in the manufacture of small refractory articles , scorifying dishes , crucibles , tubes , and one- piece furnace linings . In 1920 the lowering of the price of zirconium metal powder ( because of improved metallurgical methods ) promised the production of the metal on a semicommercial scale . In 1924 the Titanium Alloy Manufacturing Co. introduced a new opacifying agent , " Opax , " made from zircon . A year or two later some of the large pottery manufacturers became interested in the use of zirconium oxide as an opacifying agent , the increased production of titanium pigments having resulted in the production of zirconium as a by-product at a price that could compete with tin oxide . In 1928 it was reported that the industrial use of zirconium oxide was increasing steadily in the manufacture of brick , crucibles , and other refractory products , such as high- temperature cements . However , the reluctance of producers to install additional and more suitable

Jun 1, 1931

By E. R. Palowitch

This report is the result of a series of coal-cleaning tests using a dense-medium cone-type washer. Detailed results are given for 2 tests using a magnetite medium and 4 tests using a pulverized-refuse medium. Approximately 120 float-and-sink tests and over 500 separate chemical analyses were made in conjunction with these tests. In these tests higher recovery efficiencies and sharper separations were obtained when using a magnetite medium, especially on coal sizes below one-half inch. When sizes above 1 inch at low specific gravities of separation are cleaned, the pulverized refuse medium compared favorably with the magnetite medium.

Jan 1, 1956

By A. J. Kraemer

This report is one of a series dealing with oil-shale-operations in foreign countries visited and studied by Bureau of Mines oil-shale technologists within the past 4 years. Many oil-shale deposits have been discovered in Brazil and studied with various degrees of thoroughness. In this report the major emphasis is upon the oil-shale concessions of Companhia Nacional de Oleos Mineraes, in the River Valley of the State of Sao Paulo, because this oil-shale deposit is one of the most promising in Brazil for large-scale utilization for the manufacture of liquid fuels and other products of oil-shale processing, and because the opportunity was afforded to examine the concession area and to study mining, retorting, and. refining operations on these shales. Results of detailed analyses at the Oil Shale Research and Development Laboratories of the United States Bureau of Mines, Laramie, Wyo., are reported, Analyses and other date dealing with other oil-shale deposits in Brazil have been compiled from many sources. As many data have been reported as could be correlated to indicate the range of variation of the several types of shale end similar material. The oil-shale deposits in Brazil differ widely in size, richness of the shale, and of the oil. Some deposits are situate& more favorably for exploitation than others.

Jan 1, 1950

An independent contractor is defined by the Mine Safety and Health Administration (MSHA) as ?any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine.? Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines. Companies In 2007, a total of 2,999 contracting companies reported employment at coal mines to MSHA, or 35.7% of all independent contracting companies.

Aug 1, 2009

By J. R. Thoenen

This circular is part 2 of the third subject (entitled "Excavation") of a series summarizing; the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. This paper discusses the use of the power scraper, slackline cableway excavator, and hydraulic monitor, and part 3 will discuss the use of various types of dredges. Subsequent papers in the series will discuss the use of haulage equipment, the application of both excavating and haulage equipment to various types of deposits, and operating costs. THE POWER SCRAPER The power scraper is a younger member of the various forms of gravel excavators. It is a mechanized enlargement of the slip scraper and other scrapers which depend upon animals for power and has a greater range of operation from a single set-up than any other excavation unit except the slackline cableway excavator.

Jan 1, 1935

By C. R. McCann

The Bureau of Mines conducted an experimental study of conditions needed to produce flames of pulverized coal when the heat needed for ignition is sup-plied only from the flame and hot furnace refractory. An electrically heated furnace which burned about 1 pound of coal per hour was designed and fabricated. A sheath of air, surrounding the primary coal and air stream, was used to prevent entry of hot gases from recirculating combustion products. Furnace temperatures needed for ignition ranged from about 1,8300 F for an Illinois coal to 2,250° F for a Beckley seam coal. Apparent flame velocities were about 2 to 5 feet per second, increasing with volatile content of the coal and with distance from the burner mouth to the flame. The time required for ignition, approximately 0.02 to 0.07 sec, was a better measure of flame behavior than was velocity.

Jan 1, 1969

By L. C. George

The Bureau of Mines measured vapor pressures of selected mixtures in the binary system SnCla-ZnC12 by the static pressure method. Equations expressing the vapor pressure) and the heat and free energy of vaporization) as functions of temperature were developed by numerical analysis based on the sigma-plot method. It was found that the vapor pressure of any SnCl2-ZnCl2 mixture) at any temperature within the range of this investigation) could be accurately calculated from the derived values for the heat and free energy of vaporization for the mixture, with a probable error of 0.01 cm Hg or less.

Jan 1, 1967

By Doerner H. A.

From thermodynamic calculations Maier predicted that zinc oxide and methane would react at specified temperatures substantially according to equation (1). (1.) ZnO + CH4 = Zn (gas) + CO + 2H2. Other reactions that may take place are (2.) CH4 = C + 2H2. (3.) ZnO + CO = Zn (gas) + CO2. (4.) ZnO + H2 = Zn (gas) + H2O. Maier predicted that 870°C would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C. Theoretical considerations indicate that reaction (1) is reversible: this is supported, but not proved, by experimental data. The other reactions are known to be reversible. At low temperatures reaction (2) requires a catalyst and it is slow below 1000°C. Reactions (3) and (4) are rapid, but the equilibrium constants are such that only small concentrations of CO2 or H2O can be produced below 1000°C. Maier calculated that CO2 should not exceed 0.5 per cent at 870°C., and the calculation for water vapor gives a still smaller order of magnitude.

Jan 1, 1931

By Ronald S. Conti

The Bureau of Mines conducted a comprehensive laboratory study of the thermal ignitability of various carbonaceous dust clouds with particular emphasis on various ranks of coal dust. The tests were conducted using a new 1.2-L furnace. Autoignition temperatures of dust clouds were obtained as a function of coal volatility and particle size. Dust particles and gas samples were collected by a rapid-sampling system in order to study the reactions involved in preignition and postignition processes. The autoignition temperatures measured in the new 1.2-L furnace were significantly lower and therefore more conservative than those measured previously in the Godbert-Greenwald furnace. The combined effects of thermal and electrical ignition of dust clouds were also studied in the 1.2-L furnace using electrical discharges of varying energies at ambient and elevated temperatures. The minimum spark energy necessary to ignite a dust cloud decreased significantly as the temperature of the dust cloud increased.

Jan 1, 1983

By Paul R. Thimas, Edward H. Boyle

"The Bureau of Mines evaluated the long-term cost and availability of primary gold production from 135 mines and deposits worldwide. Collectively, the evaluated countries represent 93 pct of world gold production. Total recoverable gold available (as of January 1984) from a subset of 111 significant producing mines and developing deposits in 13 market economy countries (MEC's) is estimated at 810 million tr oz. The Republic of South Africa is estimated to account for 87 pct of total recoverable gold. The United States and Canada account for 4 and 4.5 pct of the total, respectively. Eighty-three percent of total recoverable gold is available at a constant 1984 break-even price of $400/tr oz, and 70 pct is available at $300/tr oz. South Africa accounts for 90 pct of the gold available at $400/tr oz or less.Major conclusions are that (1) South Africa should remain the largest world producer through the year 2000, (2) annual MEC output in 2000 should not be significantly different than current output given constant 1984 gold prices of more than $300/tr oz, and (3) there may be a significant decline in production after 2010 in the absence of major new discoveries and continued development of new mines to offset the depletion of the South African mines. INTRODUCTIONSince the late 1970's the world gold mining industry has been characterized by dynamic growth in production and volatility in price. World production in 1983 was almost 15 pct greater than in 1980, and the short-term trend continues upward. Annual dollar-based price changes since the early 1970's have been unprecedented in both magnitude and volatility. This commodity, which sold for $35/tr oz3 for over a third of a century, reached an annual average $612/tr oz in 1980. Until 1980, the future price of gold seemed set on an upward trend. Since that year, however, world gold prices have fallen by over 50 pct to slightly over $300/tr oz at the end of 1984.Against this background, this study was undertaken to determine (1) the level of world demonstrated gold resources, (2) total and annual availability of gold mine production, (3) long-run production costs per operation and by national aggregates, (4) the economic and technical factors that impact upon cost and availability, and (5) probable future mine production and cost trends."

Jan 1, 1985

By J. L. Wiley

[NOTE. - P before the number indicates that the ab tract appears in patent section. Abstract numbers without. P appear in literature section. A Abietic acid, hydrogenolysis - 404 Acetone, recovery - P-4024 Acetylacetonate catalyst - P-3352, P-3664, P-6067 Acetylene, production - P-2556, P-3169, P-4064, P-4221, P-4222, P-5002 Acid catalyst - P-4584 Salts - P-4555 See also Specific acid. Acid treatment. See Procedure. Adsorption. See Hydrogen, adsorption. Agitation. See Equipment, agitators; Procedure. Alcohols: Decomposition -1128 Hydrogenation - P-3288, P-4743 In motor fuel - 1486]

Jan 1, 1952

By N. Kumar Kittusamy, Richard E. Miller

This field study evaluated a newer and older dozer at a construction site. Both dozers performed similar activities in the same location within the construction site. Two operators participated in this study. One operator used the older equipment and the other operator used the newer equipment. Jolting and jarring measurements were taken at the seat/operator interface and at the floor of the cab. The result of this field study indicates that the newer dozer was better than the older dozer.

By Diane Schwegler-Berry, Vincent Castranova, Chang-geng Moe, Jane Y. C. Ma, Mark D. Moore, Joseph K. H. Ma, Carl J. Malanga, Ji-Hee Kane

"Effects of Bisbenzylisoquinoline Alkaloids on Alveolar Macrophages: Correlation between Binding Affinity. Inhibitory Potency and Antifibrotic Potential. CASTRANOVA, V., KANG, J-H., MA. J. K. H., Mo, C-H., MALANGA, L. J., MOORE M. D., SCHWEGLER-BERRY, D.. AND MA. J. Y. C. (1991). Toxicol. Appl. Pharmacol 108, 242-252. The Chinese have conducted extensive studies concerning the medicinal properties of plant products. In this investigation the ability of three bisbenzylisoquinoline alkaloids to inhibit particle-induced activation of alveolar macrophages was evaluated and this inhibitory potential was correlated with the ability of those drugs to bind to membrane components. Tetrandrine. i.e.. an herbal medicine used as an antifibrotic agent in China, was a potent inhibitor of particle-stimulated oxygen consumption, superoxide release, and hydrogen peroxide secretion by alveolar macrophages. Tetrandrine also exhibited substantial binding affinity for membrane lipids and alveolar macrophages. In contrast, tubocurine, an analogue with little antifibrotic potential, exhibited low binding affinity and had little effect on macrophage activation. Methoxyadiantifoline, an alkaloid of unknown antifibrotic potential, exhibited inhibitory and binding properties similar to those of tetrandrine. The data indicate that a strong relationship exists between the antifibrotic potential of these alkaloids and their ability to bind to alveolar macrophages and inhibit particle-induced activation of these phagocytes. These drugs should serve as useful probes to evaluate the role of alveolar macrophages in pulmonary fibrosis. © 1991 Academic Press, Inc.Chronic silicosis is a fibrotic disease resulting from occupational exposure to silica dust. It is manifested initially by an increase in the quantity of pulmonary surfactant (Dethloff et al., 1986). However, in later stages it is characterized by an increase in collagen formation and the development of concentric hyalinized nodular lesions in the lung (Ziskind et al., 1976). Although mechanisms for the progression of silicosis have not yet been completely defined, activation of alveolar macrophages by respirable silica particles is believed to play an important role in the etiology of this disease. Studies from our laboratory have shown that both in vitro and in vivo silica exposures result in a stimulation of macrophage release of reactive products capable of damaging the lung parenchyma (Castranova et al., 1990; Goodman et al., 1990). In addition, exposure of al¬veolar macrophages to silica results in the release of fibrogenic factors which enhance the proliferation of fibroblasts and the synthesis of collagen by these pneumocytes (Leibovich and Ross, 1976; Bitterman et al., 1982, 1983).The bisbenzylisoquinoline alkaloids, which represent the largest group among the iso-quinoline compounds isolated from the plant kingdom, are known to exhibit a broad rangeof pharmacological activities. Tetrandrine, for example, an alkaloid isolated from the root of Stephania tetrandra, has been tested for its antitumor, antihypertensive, and antisilicotic effects (Kupchan and Atland, 1973; Zeng et al., 1985; Yu et al., 1983). It is currently used in China as a treatment for angina, hypertension, and silica-induced pulmonary fibrosis (Li et al., 1981). Several related bisbenzylisoquinoline alkaloids such as methoxyadiantifoline and tubocurine have also been evaluated for medicinal effects. Methoxyadiantifoline has been shown to exhibit effects on the cardiovascular system similar to those reported for tetrandrine (Jia et al., 1988). However, to date, the antifibrotic activity of methoxyadiantifoline has not been evaluated. In contrast to tetrandrine, tubocurine, a structural analogue of this drug, has been reported to be relatively ineffective against fibrosis (Mo et al., 1982)."

Mar 1, 1992

By Danny Hagood

The drilling of horizontal boreholes as a means of degasification in advance of mining has been tried at Jim Walter Resources, Inc., No. 4 Mine. In a joint venture with the U.S. Bureau of Mines, a series of horizontal drainage boreholes have been drilled in the panels of an advancing continuous miner section with impressive results. The combined methane gas production rate has ranged from 205,000 to 680,000 cfd (cubic feet per day} with individual "in-seam" horizontal holes producing up to 332,000 cfd. The methane liberation from the ribs for the entire panel length has decreased from an average of 8.75 cfm (cubic feet per minute) per 100 feet of entry to 4.05 cfm per 100 feet, a 54 per cent reduction. The actual gas concentration as measure at the surface discharge point normally ranges from 85 per cent to 95 per cent methane. As a consequence of the significant reduction in methane liberation rates from the panels of the section, a 50 per cent increase in productivity from the section has been realized.

Jan 1, 1983

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931