Search Documents

By Lloyd Williams

1. The investigation shows that the Coal Creek has been the most productive, bed in Campbell County and contains the largest recoverable reserves of coal. The Pewee, Red Ash, and Jullico have been relatively productive beds and contain appreciable recoverable reserves of coal. The Blue Gem also has been productive in the past, but available information indicates that most of the remaining coal is Less than 28 inches thick. The Big Mary has relatively large reserves over 28 inches thick, but the coal is high in ash and sulfur. Thick partings in the Windrock bed have discouraged mining in that bed. The Poplar Creek and Rex beds generally are below drainage, and large areas have been excluded from the reserve estimate, Reserves in the Walnut Mountain bed will be difficult to mine due to the irregu¬lar thickness and lack of continuity of the bed. Estimated coal reserves are- small in the remaining five beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-Foot of coal in place, are estimated to be 398 million tons as of January 1, 1953, o? this total, 267 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1956

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSS systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By Louis R. Iverson

Patterns of species colonization, biochemical interaction among species, and competitive phenomena were studied in four reclaimed areas in western North Dakota ranging in age from one to four years after mining, along with a site from a native mixed grass prairie for comparison. Early successional changes in floristic composition and soil chemistry were quantified. The mined sites had been contoured, topsoiled, fertilized and seeded. Despite seeding of agronomic species, initial colonization was by fugitive species; analysis of the seed bank in topsoil showed that the most dominant colonizers immigrate after topsoiling. Of the 95 species encountered, Kuchia scoparia was the most dominant in the first two years following mining. Kochlo had relatively low densities in the first year (50-80 plants m-2), but was robust and attained heights of 88 cm with a biomass of about 400 g m-2 In the second year, the plant densities increased to over 10,000 plants m"2 but the height and biomass were reduced to 15 cm and 90 g m-2. However, during the third and fourth years Kochia density declined and was practically non-existent by the fourth year, while the planted Agropyron grasses had concomitantly increased. Other pioneers like Amaran thus retroflexus, Chenopodlum album, Helianthus annuus, Salsola spp. And Setaria spp. showed a less abrupt but similar decline. Chemical analysis of the soils over the same time period showed decreases in electrical conductivity (E.C.), and in the concentrations of P, Ca, Mg, Na, Li, Sr, and SO4 (due to leaching), while N increased. Field studies were conducted on the competitive relations between the dominant species - Kochia scoparia and Agropyron spp. - during early succession. It was found the Kochia acted as a "nurse" crop for several months during the first year of Agropyron spp. establishment, but then began to shade heavily by late July, thus reducing grass tillering. Field and growth chamber experiments on the intraspecific competition relations of Kochia demonstrated that its density and dry matter production, per plant and per unit area, conformed to several laws of plant population biology. Autotoxicity or the depression in growth of a species by its own degradation compounds, in Kochia, appears to be the main factor causing the decline in its growth. Results from a field experiment indicated that thinning dense second year Kochia stands to the density of first year stands did not alter the growth of Kochia, providing strong evidence for autotoxicity. Similarly, several growth chamber experiments demonstrated that small amounts of decaying Kochia leaves and especially roots were toxic to Kochia growth, but not Melilotus officinalis or Agropyron canlnum, Chemical analysis of the soils and plant tissues indicated nutritional im¬balances as shown by P/Mn and P/Zn ratios may be responsible for autotoxicity. In addition to Kochia, a bioassay experiment showed allelochemics to be important in several other colonizing species. Although our results indicate that later stage species generally have greater toxicities than first year colonizers, autotoxicity in the very initial stages seems to be accentuated by harsh habitat conditions. Several practices (mowing. fire, etc.) are used to manage grasslands. Mowing of the first year erect, annual, colonizing vegetation was shown to be beneficial in the growth and establishment of wheatgrasses after mining in western North Dakota. Plots containing Kochio predominantly were mowed in mid-and late-July, and in mid-August, during the first year of growth after recontouring, replacing topsoil. seeding and fertilizing. It was found the Kochia densities were reduced to two percent of the control and its biomass reduced to less than one-third when the area was mowed in mid-August. On the other hand, wheatgrasses showed increases of 23% in stem density and 860% in biomass production over the controls when mowed in mid-August. The mowing of Kochia just before seed-set apparently reduces interspecific competition between Kochia and Agropyron spp. during the following growing season. The method is highly recommended for use in hastening the establishment of planted grasses.

Jan 1, 1982

By Richard I. Barnhisel

At the Sinclair Study Site it was found that the deeper the soil the greater the yield of corn, soybeans, wheat, alfalfa, and timothy. Yields at this location were generally lower than those at the Alston Surface Mine. At Alston the non-prime land treatments generally produced greater yields for all crops than did the prime farmland treatments, however, the intermediate soil thickness, 20 cm topsoil over 40 cm of subsoil, gave the best yields, provided it's subsoil had been limed. From a chemical point of view, acidic spoils do not need to be buried by 120 cm or 4 feet of soil, provided adequate lime is applied to these spoils as a barrier prior to placement of good quality topsoil and only forage crops are to be grown. The burial depth must be increased to as much as 75 cm when grain crops such as corn or soybeans are to be grown. This response to burial depth appears to be related to water storage needed by the crop and not due to toxic effects of the spoils. A conventional farm tractor-mounted subsoiler increased yields of soybeans and corn the first one or two years, but the effect was diminished with time. Subsoiling did not produce significant increases for alfalfa or wheat. However, ripping with a bulldozer produced significant yield responses, especially for corn and soybeans, that have lasted for at least three years. The ripping effectively reduced the bulk density at least within the zones through which the ripper had passed. Liming the upper 20 cm of subsoil significantly increased yields of alfalfa, corn, and soybeans. There also appeared to be an interaction between this lime treatment and soil depth. Yields of some grain and forage crops may be high enough to meet target levels for bond release for prime farmland. Based on the present study, one should not expect corn yields to be high enough to meet bond release. This statement should not be considered final since the experiment is not complete.

Jan 1, 1983

By Donald B. Lindsay

This report presents the findings of an investigation into the characteristics of a number of techniques for cleaning ambient air with special emphasis on their applicability to the removal of the short-lived radioactive decay products of 222-radon, the so-called " radon daughters" that have been identified with the induction of lung cancer in underground uranium miners. The purpose of the study was to review the requirements for control of radon daughter concentrations in mine air, and to examine all techniques whose feasibility has been demonstrated in principle and which in our judgment would be capable of meeting those requirements. The study has included a review of all pertinent literature, both technical and proprietary, on the subject of the control of miner exposure to the radon daughters and in the area of potentially applicable air cleaning technology. Information about the nature of the problem and about the experience of the uranium mining industry in applying air cleaning methods to its solution was obtained by visiting mines where such methods are in use, and by written correspondence and telephone conversations with other industry sources. Information on performance characteristics and costs of applicable air cleaning methods and equipment was obtained from the experience of our own engineering staff and by visits, interviews, and correspondence with manufacturers of industrial air cleaning equipment.

Jan 1, 1978

By Floyd D. Varley, C. M. K. Boldt

Toolbox training is often described as short, informal training conducted at a worksite by technically competent persons for the benefit of a work team. The key feature of toolbox training is the focus on a work team and what is important to that group in its workplace. Toolbox training conducted by peers can connect miners and establish the feeling that the hazard is a real threat to them. This feeling can bridge the gap between delivery of a safety message and behavioral changes that can prevent an accident. Toolbox training is a popular form of "maintenance" training that should not be used to teach a new skill. The 10- or 15-minute toolbox session is simply too short a time to teach or learn a new skill and test for skill development. However, the toolbox format is an excellent way to inform workers of changes in workplace rules, conditions, or hazards by bringing the discussion of change to the level of the work group and suggesting how a change will affect the way workers perform their jobs. Toolbox training should be structured to address a very specific hazard. That is, the hazard source should be identified and the effect of the hazard on the worker described. The temptation to discuss a safety subject in broad terms will result in an equally vague result. For instance, discussing "equipment guards" is inappropriate for a 15-minute training session. There simply is not enough time to cover all the hazards and their remedies. A more appropriate topic would be "placing guards on a conveyor return roller" or "hazards of cleaning a conveyor return roller." Each topic is concise enough to allow the trainer time to define a particular threat to the safety of miners and discuss ways to defend against that threat. The clearest way to a safe workplace is to identify hazards methodically and eliminate them. This cannot be done with sweeping, generalized training. Some best practices that will protect a worker from the hazard should be presented, and the hazard should be located at the specific worksite. Toolbox training is an opportunity for the work team to participate in learning and share experiences and knowledge, often through storytelling. Storytelling is an ancient form of passing along information in an entertaining way. It is entertaining because it draws the listener in with imagination and creativity. Stories told within work groups are a way for miners to exchange experiences in which they made mistakes that resulted in an accident or a near-miss and learned a valuable lesson. Thus, co-workers can learn from others without the pain or fear that accompanied the storyteller's learning path. To encourage these shared experiences, the people in the group must be comfortable with one another. Participation doesn't stop with listening to a near-miss story or informing the group of an unsafe work practice. Participation by sharing experiences, knowledge, and skills should lead toward action in changing the unsafe tool, practice, or machine (Wallerstein, 1992). This power to change is called empowerment. Empowered workers use toolbox training sessions to discuss a problem; direct their own knowledge, experience, and talents in the context of their work environment to solve the problem; and put into practice what they have learned by sharing (Baker, 1992). A worker is much more likely to implement changes they have contributed to creating than changes forced upon them. Toolbox training functions best when the group size is small (under 20) and composed of workers with similar job functions. While combining all workers on a shift or multiple shifts may be convenient, the level of participation will drop dramatically as group size increases and participants are less connected. Similarly, when the work group participants are from different job functions, keeping the materials relevant to the individual becomes more difficult. The role of management in the toolbox training system is to communicate among various groups so that all groups at a mine site are hearing the same message. In very small operations, combining work groups can be productive if the trainer can promote open discussions and lead the group to solutions that address the needs of all and not let one group or individual dominate the discussion. WHY USE NARRATIVE METHODS An effective communications tool is to use stories as a means of describing a hazard and its consequences. Historically, using stories to transfer knowledge between individuals of the same and different generations is well established. All good stories share the same elements required to communicate safety principles. Stories require a setting (the part of the workplace), a plot (the circumstances that lead to a hazard), the solution (best practices), the lesson (what can happen), and the result (what will be done to prevent the hazard) (Dennehy, 1999).

Jan 1, 2002

By J. G. Haymes

This report by the Bureau of Mines is the first of two proposed papers on evaluation of spectrophotometric, spectrographic, polarographic, and other analytical methods for quantitatively determining impurities in high-purity tungsten. Some of the methods described are standard methods that have been successfully applied to determine low-level impurities, several are modifications of known methods, and some procedures are entirely original. The Bureau of Mines is actively engaged in tungsten research because tungsten has an extremely high melting point, in fact the highest of any known metal. The metallurgist must know the content of impurities in tungsten because of the marked effects even micro amounts of impurity elements have on its physical properties. The Bureau procured a number of analyzed samples of above-average purity from research laboratories of companies engaged in production and fabrication of tungsten. These samples were investigated by the analytical procedures of those companies for several metallic impurities. Subsequent analytical laboratory determination of impurities in these samples agreed with the analyses as reported. With this assurance that analytical methods were basically accurate for metallic impurities, procedures for the determination of several of these elements were modified to lower the limits of detection and increase the sensitivity of methods. Carbon and the gases hydrogen, nitrogen, and oxygen were determined by standard instrumental methods, modified to provide greater sensitivity for reliable determinations when content of these elements was low. After the reliability of the modified procedures was affirmed, they were used as a product evaluation guide in the development of a vapor-plating technique for the production of high-purity tungsten. The following list of elements can be determined by one or more of these methods: AI, B, Be, Ca, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, S1, Sn, Ti, V, and Zn. In addition, a vacuum-fusion method for the determination of H, N, and 0, and a conductometric method for carbon are described. Lower limits of determination and detection for each element listed are given.

Jan 1, 1962

By E. H. BURROUCHS

This bulletin is the third of the series of yearly petroleum bibliographies being published by the Bureau of Mines. The two preceding, Bulletin 149 and Bulletin 165, were for the years 1915 and 1916, respectively. In arranging the references the same general scheme has been followed, but as in those bulletins, several changes and additions have been made in the classifica.tion, the more important being in the classes " Development and production " and "Refining and refineries." German periodicals for 1917 were not procurable and references to articles in those and in other foreign journals that were not available have been credited to the sources from which they were procured.

Jan 1, 1920

By A. J. Farstad

Electromagnetic location tests were conducted by Westinghouse Georesearch Laboratory under the sponsorship of the U. S. Bureau of Mines at the Galena Mine in Northwest Idaho. The objectives of these tests were to evaluate the performance in deep hardrock mines of an electromagnetic location system previously developed for the U. S. Bureau of Mines for use in coal mines. Tests were performed using long wire transmitting antennas as well as horizontal and vertical transmitting loops at depths from 3000 feet to 4300 feet (995 metres to 1311 metres). Surface measurements were made of magnetic field strengths, field strength patterns, and background noise, These measurements were compared with theoretical predictions for a homogeneous ground conductivity consistent with this particular geologic region. The results of the Galena Mine tests show conclusively that light-weight portable electromagnetic transmitters can be effectively utilized to provide uplink communications and location information in deep hardrock mines. Typical metal mines such as Galena utilize deep vertical shafts for mine access and haulage and these shafts produce signal enhancement at the surface from underground electromagnetic transmitters by as much as 30 dB. The results also show that horizontal wire configuration can serve as an effective alternative to the magnetic dipole antenna as a rescue transmitting antennaa and can be used when the required area is not available for deployment of a loop antenna. In spite of the electromagnetic coupling effects observed in the vicinity of the shafts, the location accuracy obtained still provided useful information on the general location of the transmitting sources involved. The horizontal wire location accuracy was within 46 metres, while the vertical magnetic dipole and the horizontal magnetic dipole accuracies were within 152 metres and 110 metres respectively at a 915 metre depth.

Jan 1, 1973

By G. F. Livingston, F. K. Shelton, J. C. Stahl, R. E. Churchward

"INTRODUCTION An investigation of the metallurgy of cobalt from domestic ores has been in progress since February 1940 and has resulted in the formation of a hydrometallurgleal process for the production of electrolytic cobalt metal. Previous reports of these investigations have been given by F. K. Shelton; 7/ and Ruth E. Churchwrd, F. K. Shelton, and G. Knickerbocker. 8/ Briefly, the process, as applied to ores containing cobalt oxide, consists of leaching with H2SO3 or, preferably, with H2SO3 and H2SO4, to dissolve the cobalt. The cobalt solution passes through one or more purification stages to remove iron and elements of the copper group, and cobalt carbonate is precipitated under carefully controlled pH conditions. The cobalt carbonate is dissolved in on acid electrolyte containing sulfuric acid, boric acid, and sodium fluoride. The electrolyte then proceeds to electrolytic cells where cobalt is plated as a metal and sulfuric acid is regenerated.The present paper contains the results of several investigations signed to give a more complete chemical and engineering understanding of different unit processes involved in the electrowinning of colbat. Some work has been done to broaden the process to include arseniferrous cobalt ores as well as the oxide ores upon which the investigation was initiated. Most of the data presented herein have been obtained since the release of the previous reports; any changes suggested heroin that conflict with recommendations in earlier reports are based on more complete data and usually are preferable."

Nov 1, 1945

By William W. Adams

Accidents to men employed in the quarrying and related industries of the United States were more numerous, absolutely and relatively, in 1937 than in 1936. Fortunately, the entire increase was in the category of nonfatal injuries, as accidents causing death declined in number and in proportion to the number of man-hours worked. Employment increased. More men were employed, more man-days and man-hours were worked, and the average employee had more hours of work than in 1936. Reports covering all commercial operations showed that 84,094 men were employed an increase of 5.1 percent over 1936. The number of man-hours of work performed by the industry was, 158 millions, an increase of 7.6 percent. Seventy-seven men were killed by accidents, a, reduction of 14 from the year before, and 6,348 men were injured and disabled for more than the remainder of the day on which the accident occurred, 11 percent more than in 1936. The fatality rate of 0.49 per million man-hours of exposure in 1937 compared favorably with the rate of 0.62 for the previous year, whereas the non-fatal-injury rate of 40.10 was 3.2 percent higher than the rate of 38.87 for 1936.

Jan 1, 1940

By John D. Warne

"INTRODUCTION Initiated as a part of the Bureau of Mines program for development of strategic minerals for national defense, Investigation of the fluorspar deposits of the Northgate area was begun in June 1944 and completed in March l946. Mining Operations were active in the district during most of the period of investigation.The Fluorspar, Fluorine, and Camp Creek mines develop the two more promising vein systems known in the area, the Fluorspar group of claims covering one vein system and the Fluorine and Camp Creek groups the other. Figure 1 shows the location of the properties. The Fluorspar and Fluorine properties were operated (except during the winter months) by the Western Fluorspar Corp. The Camp Creek mine was operated during 1943 and 1944 by Kramer Mines, Inc.The properties were examined April 20 and again November 4 to 12, 1943, by C. R. Wilfley, a Bureau of Mines engineer, who recommended work to determine ore reserves and to serve as a guide for development. Investigations by the Bureau of Mines covered all three properties."

Aug 1, 1947

By Harry W. Campbell

A Bureau of Mines investigation identified no mineral deposits in the Lost Creek RARE II area. Sand and gravel has been mined from alluvial flood plain deposits just outside the RARE II boundary. An oil and gas lease application which includes the eastern portion of the RARE II area is pending. Abundant basalt in the area can be crushed and used as aggregate; but it could not compete with similar deposits in more favorable locations, or with cheaper substitutes such as volcanic cinders or sand and gravel which are available outside the study area closer to major markets. No indication of coal or geothermal energy resources was found. INTRODUCTION Location and Access The Lost Creek RARE II area encompasses 8,300 acres (3,400 ha) of Lassen National Forest in north-central California, about 20 mi (30 km) north of Lassen Peak. The closest city is Redding, California, 50 air mi (80 km) southwest. Peripheral access is provided by State Highway 89 passing near the western RARE II boundary (fig. 1). The Pacific Crest Trail traverses the western margin of Hat Creek Rim adjacent to the eastern boundary of the area.

Jan 1, 1983

By T. J. Ballard

"INTRODUCTION The Buck. Creek corundum area of Clay County, North Carolina, includes one of the largest single masses of peridotite outcrops in the whole Appalachian Range and has been described by Pratt, an early authority on corundum, as offering one of the best potentialities for corundum production in North Carolina.Two principal types of corundum deposits are found at Buck Creek the vein type and the corundum-bearing amphibolite dikes.The vein deposits occur in structural fissures that strike north to northeast in a gangue of feldspar, zoisite, an, chlorite. The corundum is generally coarse-grained and good-quality. The corundum content varies from several percent to 50 percent.The corundum in the amphibolites is more or less disseminated through the dike, is generally lower-grade, and is less in quantity, than the vein corundum. About 50 percent of the amphibolite corundum is coarse enough for snagging-wheel grade but is difficult to separate from the amphibolite.Production from the Buck Creek area has been small and came mainly from high-grade pocket in the vein deposits. Pratt 3/ reports 300 tons of corundum ore was produced to about 1896. No record of subsequent production is available.The critical shortage of corundum during the war, due to transportation difficulties and the depletion of deposits abroad, prompted the Bureau of Mines to investigate domestic reserves.After a favorable report was obtained on the Buck Creek area, the Bureau began exploration of the deposit in September 1943 and continued until February 1945."

Apr 1, 1947

By H. F. Yancey, E. Zane

"INTRODUCTION The term ""friability"" as applied to coal may be defined as the physical property of coal which expresses its tendency to become reduced in size during handling as a result of such external forces as impact and attrition. Thus friability is a quantitative concept and property, and hence can only be defined in relative terms or in terms of measurement. Methods of measurement are difficult to formulate and apply because coal is anything but homogeneous in physical structure and chemical constitution. aMoreover, friability itself is a composite property obviously dependent upon a group of other specific characteristics such as cleavage, fracture, tenacity, hardness, and elasticity, which vary from coal to coal with change in rank and even between individual coals of the same rank. These characteristics affect the friability values of different coals to varying degrees, but this fact does not impair the usefulness of and the need for friability measurements.The amount of breakage or degradation in size that a coal suffers in mining, preparation, and subsequent handling depends upon its inherent friability and the severity of the handling treatment which it receives from the time it is taken from the bed until it reaches the consumer. The value of the coal to the producer and jobber depends in large measure upon these same factors--friability and severity of treatment—because the larger sizes still command a premium in the ordinary market. Although much has been accomplished by the coal-producing industry in minimizing the breakage of coal in mining and preparation, it is apparent that additional reductions in breakage must await further improvements in design of coal-handling equipment. Such improvements will result from more intensive investigations of the extent of breakage or degradation in size occasioned by specific mining and handling operations and the development and application of standardized methods of evaluating friability.The work described in this report was undertaken to assist in the development of standard methods for evaluating the friability of coal. Specifically, the work deals with a Comparison of the various methods previously proposed for estimating the friability of coal and coal products. This same objective is now being sought at a number of other institutions, both in the United States and Canada, by a committee of the American Society for Testing Materials. It is believed that by providing additional information concerning a property of coal pertinent to its increased usefulness, the work described will supplement and increase the useful of the data which long have been, and still are being, furnished by the bureau of Mines on the composition of coals of the United States."

Jun 1, 1933

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network, and 2)development of , set of digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the model; and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated for their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

By Donald E. Buck

In 1988, Albania's centrally planned economy continued to decline. The country's officially published yearend economic report did not contain concrete results such as the growth of national income or industrial output. 2 The shortfall for central budget earnings for 1988 amounted to 9% below the planned target. Losses in industry were attributed to poor management and organization, as well as to low technical standards and excessive consumption of fuels and raw materials. The construction, energy, and mining sectors of industry did not meet their annual production plans. As in 1987, within these sectors, the chromite and petroleum extracting and processing industries continued to lag in output. Both chromite and petroleum remained Albania's chief sources of foreign exchange; the production downturn of these commodities continued to negatively affect the country's foreign trade position, especially in view of constitutional prohibitions against using foreign credit to finance trade. The chief events in the minerals industry in 1988 included the construction startup of the first of four planned new concentrators at the Bulquize chromite mine, as well as the construction startup of new ferrochromium capacities at Elbasan. Also, the copper mining industry reported the completion of facility expansion at the Perlat mine in the Mid-rite district. Albania began new facility construction at the Dinamo heavy-equipment enterprise at Tirana to maximize self-sufficiency in mining equipment production. Upon completion, the new factory would double the out-put of mining equipment at the enterprise and would introduce new designs for electric trucks and pneumatic drills for the mining industry. The new facility would also increase the production of new machinery and equipment for the country's beneficiation plants.

Jan 1, 1990

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' Circular (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circular pros. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that effects the net expansion of the change in both industrial and test ovens. Various test results5/ have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; but no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors.]

Jan 1, 1940

By R. A. Isberg

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75o coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 1, 1981