Search Documents

By David C. Oyler

The U.S. Bureau of Mines studied the interaction of longwall shield supports and adjacent strata at the Meigs No. 31 Mine in southeastern Ohio. Twenty-three legs of twenty shields at midface were instrumented with pressure transducers and monitored for 11 weeks. During the project, leg setting pressures were reduced twice to determine the effect of setting pressure on shield-strata interaction. No correlation was observed between setting pressure and leg loading rates. The shield loading profiles were consistent with a model in which the roof consists of two zones, a thin immediate roof loading the shields well below the typical setting force and a main roof zone essentially supported by the coal and gob and loading shields through its convergence. This model was used to develop an equation for estimating average loading rates at the site. The only variable of the equation is time, and the equation consists of an exponential term to account for the immediate roof loading and a linear term to account for main roof loading. The equation gave good correlation with average loading rates, but the variation in loading from cycle to cycle was too great for the equation to give good predictions of individual cycle loading rates.

Jan 1, 2010

By Steven J. Schatzel

Prior research has suggested that the source of respirable silica dust in underground coal mines is typically the immediate top or bottom lithology adjacent to the mined seam, not mineral matter bound within the mined coal bed. Geochemical analyses were applied in an effort to identify the specific source rock of respirable quartz dust in coal mines. The analyses also demonstrate the compositional changes that take place in the generation of the respirable dust fraction from parent rock material. All six mine sites were mining coal with relatively low mineral matter content, although two mines were operating in the Fire Clay coal bed which contains a persistent tonstein. Interpretations of Ca, Mg, Mn, Na, and K concentrations strongly suggest that the top strata above the mined seam is the primary source of mineral dust produced during mining. One site indicates a mixed or bottom source, possibly due to site specific conditions. Respirable dust compositional analyses suggest a direct relationship between the quantity of mineral Si and the quantity of quartz Si. A similar relationship was not found in either the top or bottom rocks adjacent to the mined seam. An apparent loss of elemental Al was noted in the respirable dust fraction when compared to potential parent rock sources. Elemental Al is present in top and bottom rock strata within illite, kaolinite, feldspar, and chlorite. A possible explanation for loss of Al in the respirable dust samples is the removal of clays and possibly chlorite minerals. It is expected that removal of this portion of the Al bearing mineral matter occurs during rock abrasion and dust transport prior to dust capture on the samplers.

Jan 1, 2009

By C. W. Davis

During the second year of its existence, the Ore-Testing Section has actively prosecuted work in the standardization of testing methods, in conducting routine tests and analyses for other Government agencies, and in the determination of recommended processes for the treatment of representative ores from mining districts. Close cooperation has been maintained between the members and units of this Section and those of other Sections, J. A. Woolf and J. B. Clemmer have continued to act in an advisory capacity and R. E. Head has contributed valuable assistance in the microscopic examination of ores and metallurgical products that did not respond readily to standard treatment methods.

Jan 1, 1938

By C. W. Davis

During the second year of its existence the Ore-Testing Section has actively prosecuted work in the standardization of testing methods, in conducting routine tests and analyses for other Government agencies, and in the determination of recommended processes for the treatment of representative ores from mining districts. Close cooperation has been maintained between the members and units of this Section and those of other Sections. J. A. Woolf and J, B. Clemmer have continued to act in an advisory capacity and. R. E. Head has contributed valuable assistance in the microscopic examination of ores and metallurgical products that did not respond readily to standard treatment methods.

Jan 1, 1938

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, increased about 4% in 1990. The decrease in the value of tripoli production was the result of a decrease in total production. Emery decreased owing to a decrease in the volume of the material produced. Special silica stone experienced a decrease in unit value and in the quantity produced. Garnet showed an 8 % increase in quantity and an 8 % increase in unit value. Staurolite increased about 38 % in the quantity produced, and the value of production increased about 36 %. The fused aluminum oxide industry showed a 12 % decline in the quantity produced and a 13 % decline in the value of production. The silicon carbide industry saw a 47 % decrease in the quantity produced and a 23 % decrease in the value of production. Combined, the industries decreased 17 % in quantity and value compared with those of 1990.

Jan 1, 1993

By Roy F. Abernethy

This publication by the Federal Bureau of Mines contains the free-swelling indexes for 2,812 samples of coal received from January 26, 1948, to July 15, 1957, and the Hardgrove grindability indexes for 2,339 samples of coal received from June 23, 1947, to July 15, 1957. These data consist of the origin of the sample, bed name, and analysis. Summaries show the high, low, and average values for each bed. The free-swelling index is a relative measure of the caking properties of a coal when burned on a grate, and the Hardgrove grindability index is used to estimate the relative ease of grinding coals. Development and standardization of these test procedures were at a much later date than those for the more familiar tests, such as proximate and ultimate analyses and calorific value determinations. The newer tests are valuable in supplying supplemental information, particularly for assisting in evaluating coals used in certain types of combustion processes.4/ Data from such tests are important to designers of burning equipment, operating engineers, and purchasing agents. Data from these newer tests are scarce and scattered through a number of publications. Special projects were started to determine the free-swelling and grindability indexes, in addition to the regular analyses on the tipple samples collected by Bureau engineers. Since the start of these special projects, all the coal fields of commercial importance have been adequately covered in the sampling program.

Jan 1, 1961

By Hugh D. Pallister

Alabama probably has the most extensive deposits of high-grade flake graphite in the United States and was the largest producer during World War I. Therefore, with the outbreak of World War II, users of flake graphite turned again to Alabama to supply their requirements. Flake graphite is the most important ingredient contained in graphite crucibles used in melting crucible steel and special alloys essential for war purposes. Early in World War II the Army and Navy placed flake graphite on the list of critical war materials. During World War I, when the supply of Ceylon graphite (then in demand) was cut off, large quantities of flake graphite were produced in Alabama, and about 40 mills were built. Most of these were abandoned after the war when imports of the cheaper Madagascar flake (which gradually replaced Ceylon graphite) began to reach this country. With the beginning of World War II, the Madagascar supply was cut off', and consumers were again compelled to look to domestic sources for their supplies. They found only one small mill in operation, that of the Ceylon Graphite Co. in Coosa County, Ala. The Bureau of Mines made a preliminary examination of the Alabama flake graphite deposits in 1940. Samples were taken and tested at the Southern Experiment Station at Tuscaloosa.

Jan 1, 1948

By Raymond G. Travis

This report describes coal-mining methods, power requirements, coal production and distribution, and coal resources of the Bull Mountain coal field in Musselshell and Yellowstone Counties, south-central Montana Investigations in the field, were conducted by Bureau of Mines engineers The report contains a short summary of the geology and geography of the field and discusses the following information secured during the field study: Method of mining practiced at each mine, including a description of each phase of the mining cycle. Coal produced and its distribution at each mine. Power requirements and the consumption of electricity per ton of coal produced by mines. Number of non employed by mines, and the production per man per shift underground and the over-all production per man employed. Estimates of future production and power requirements for the field as a whole. This information should be of benefit to any company or individual planning the development of now coal mines in the area or the expansion of present operations.

Jan 1, 1950

By C. W. Smith

The U.S. Bureau of Mines conducted research to determine the effect of ground water control on the dewatering of phosphatic clay wastes. Two storage impoundments were constructed. One impoundment was surrounded on three sides with a series of well points (shallow vertical wells) to lower the ambient water table and the second impoundment served as a control. Ground water was pumped from the area surrounding the test impoundment for a period of 490 days. A constant pumping rate of 60 gal/min resulted in a water table drawdown of 13 ft, approximating the bottom of the impoundment. At the end of the test period percent solids in the test impoundment was 35 pct, while in the control impoundment percent solids was only 26.8 pct. Percent solids of greater than 30 pct is required for capping and final reclamation using fertile overburden.

Jan 1, 1989

By Gregory J. Chekan

The Bureau of Mines, in an effort to improve planning and development in coal mining, is investigating strata interactions associated with mining of multiple coalbeds. Two common interactions that occur between adjacent coalbeds are subsidence and pillar load transfer. The study described involves underground observations and measurements conducted at two Pennsylvania mines, each affected by one of these interactions. At the mine affected by subsidence, measurements show that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. At the mine affected by pillar load transfer, Initial in situ measurements have shown the existence of a pressure arch in the lower workings. Prior research has shown that arch interaction between two adjacent openings can create stress concentrations in the in-nerburden. Underground measurements and results obtained from both mine sites correlate with theoretical and photoelastic multiple-seam models, and eventually these field data will serve to refine model accuracy. Further study of multiple-seam interaction mechanisms will lead to improved mine planning, increased resource conservation, and a safer working environment.

Jan 1, 1986

By Arno C. Fieldner

From July 1, 1949, to July 1, 1950, the Bureau of Mines conducted the research and technologic work on coal and coal products that is summarized in this report. The research, described in this fifteenth of a series of resumes, is presented in more detail in publications (see footnote references) that appeared during the fiscal year, though in some cases research data are given that have not been published elsewhere. Results of research in the experimental coal mine, on explosives, and on gas and dust explosions will be found in Bureau of Mines Report of Investigations 4228, Annual Report of Research and Technologic Work on Explosives, Explosions, and Flames, Fiscal Year 1950. An over-all view of our coal, oil, end natural-gas reserves was presented, and the future possibilities for the, production of synthetic liquid fuels from coal were delineated.3/

Jan 1, 1951

By Howard W. Kilau

The U.S. Bureau of Mines is investigating surfactants added to water sprays to enhance the control of dust during coal mining operations. The objective of the present work was to establish the general applicability of adding sulfate ion to anionic surfactant solutions in order to improve wetting action. This was pursued through laboratory wettability testing of four anionic surfactants and one nonionic surfactant in combination with various concentrations of sulfate ion. The experimental results demonstrated that the addition of sulfate ion enhanced the wetting characteristics of all the anionic surfactants when applied to hard-to-wet coals, while easy-to-wet coal showed more complex wetting behavior. Sulfate ion in the presence of nonionic surfactant enhanced wetting only slightly or not at all. Surface tension measurements of the dilute aqueous surfactant-sulfate anion solutions indicated this property was not important in coal-wetting phenomena, as long as the value was below the critical value for coal. Sulfate ion helps surfactant reduce surface tension but primarily appears to affect wetting action by altering the adsorption characteristics of surfactant on the coal surface.

Jan 1, 1990

By D. L. Soreck

The hazards to the public posed by abandoned mine shafts are well documented. As private development encroaches on previously mined areas, the potential for fatalities and serious injuries from abandoned mine shafts increases. The U.S. Bureau of Mines has conducted research into cellular concrete as a material for sealing these openings. The current work involves testing the characteristics of cellular concrete before and after it had been pumped or dropped from different heights into a simulated mine shaft. Cellular concrete was pumped vertically up to and subsequently dropped from heights of 18 and 37 m into concrete forms. Wet density measurements were made at multiple sampling points in the test circuit. Air content determinations and uniaxial compressive strength testing were conducted. Research results showed significant loss in air content and changes in the characteristics of cellular concrete during pumping or dropping from various heights. Recommendations on effective use of cellular concrete for sealing abandoned mine shafts are made.

Jan 1, 2010

By Lowell B. Moon

Concern over possible wartime shortages finally resulted in passage of the Strategic Materials Act in 1939. As authorized by one section of this legislation, the Bureau of Mines proceeded to investigate deposits of seven strategic minerals with the objective of developing tonnages of low-grade material that could be mined in an emergency. During the war, the size of the program and the number of strategic minerals were increased, and the objective was the more immediate one of aiding production. Since the war, the size of the program has been reduced, but the number of minerals on the strategic list continues to be large. The objective has returned to that of 1939. In the course of the program, more than 10,000 examinations were made and about 1,300 projects were run on deposits of 33 different commodities. A considerable contribution to war production was made in six of the commodities investigated, and a minor contribution was made in twelve others. Substantial reserves have been indicated in 19 minerals. Private interest is currently active in some of the deposits developed in 14 commodities.

Jan 1, 1950

By Robert S. Dalzell

Following the introduction of roof shields to the U.S. longwall mining scene in 1975, the number of shield faces (faces supported by shields) has increased steadily, and the occurrence of accidents associated with ground control inadequacies at longwall operations has shown a downward trend. However, ground control problems in longwall mining still exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. In this report, the Bureau of Mines addresses the problem of longwall roof control. The report presents a review of foreign remedial and strata replacement techniques for longwall faces and evaluates their potential for domestic application. The technology reviewed includes meshing, chemical rock stabilization, cribbing, strain-absorbent modules, inflatables, synthetic foam, and monolithic fills.

Jan 1, 1985

By JOE SIERAKOSKI, W. R. Hardwick

This paper , which describes mining methods and practices at the Johnson Camp copper -zinc mine , Coronado Copper & Zinc Co. , Cochise County , Ariz . , is one of a series being prepared by the Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . Johnson Camp is in the eastern foothills of the Little Dragoon Mountains in secs . 23 , 24 , 25 , and 26 , T. 15 S. , R. 22 E. ( fig . 1 ) . The mining property is in the low, rolling foothills at an altitude of slightly over 5,000 feet above sea level ( fig . 2 ) . The area is covered with scattered grass and small desert shrubs . The climate is mild , with hot summers and mild winters . The average annual precipitation is about 12 inches . The nearest surface water is the San Pedro River , some 12 miles west of the mine . The property is owned by the Coronado Copper & Zinc Co. , Los Angeles , Calif . This report gives a brief history of the property , describes the general geology of the area and of the ore deposits , outlines the methods of prospecting and exploration , and gives the methods of sampling and of estimating ore reserves . Development and stoping methods are explained . Underground transportation , ventilation , mine drainage , and safety measures also are described . The last section gives a brief description of the milling practice .

Jun 1, 1957

By Charles B. Kenahan

A summary of Bureau of Mines research on utilization and disposal of solid wastes is presented, accompanied by an extensive bibliography of related publications. The Bureau's Solid Waste and Materials Recycling Program is directed toward four main areas of research, development, and demonstration: (1) extraction of mineral, metal, and energy values from urban refuse; (2) upgrading and recycling of automotive and related ferrous and nonferrous scrap; (3) utilization and stabilization of mine, mill, and smelter wastes; and (4) recovery and reuse of values from industrial waste products. A contract and grant program that supplements the in-house research and aids in the training of manpower in management of mineral-, metal-, and energy -based solid wastes is also discussed. This publication is an updating of Bureau of Mines Information Circular 8460 issued March 1970.

Jan 1, 1971

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at a vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

By Thomas M. Nasiatka

This report briefly describes the present state of the art and the technological highlights of tunneling from its inception to the present. The discussion is concerned primarily with tunnels driven through relatively competent rock for mine development and various civil purposes. In addition to pinpointing the major technological breakthroughs in tunneling, this report indicates their general effect on the speed of tunneling. The tunneling speeds are based upon data from approximately 80 tunnels listed in the appendix. These data include length; cross section shape and dimension; type of rock; tunneling method; method of breaking, loading, and transporting the rock; average linear progress rate; and cost in values during the period of construction. Most of the tunnels described have diameters of 15 to 30 feet.

Jan 1, 1968