Search Documents

By Kihong Park, Matthews C. Habjan, Arthur L. Miller

New Mining Safety and Health Administration (MSHA) regulations limit the mass concentration of airborne diesel particulate matter (DPM) or, more specifically, the concentration of elemental carbon (EC), in underground mines. The mine operators are responding by introducing a variety of controls to reduce DPM in the mines, potentially including the evaluation of new maintenance procedures to reduce underground mine vehicle emissions. There is currently a lack of an inexpensive and dependable method to directly measure the DPM concentration emitted from the vehicle tailpipe. To that end, this work demonstrated a simple field portable method for estimating the mass concentration of elemental carbon exiting the tailpipe of a diesel engine using a direct reading photometer. Simultaneous measurements of tailpipe exhaust were made with a Thermo Electron Personal DataRAM 1200 photometer (particulate mass concentration based on light scattering) and by analyzing PM2.5 and PM1.0 samples collected on quartz fiber filters using the National Institute of Occupational Safety and Health (NIOSH) method 5040 (mass concentration of EC via thermal-optical method). Results indicate surprisingly good correlation (R2 ) 0.97) of the two methods when the data are adjusted for relative humidity (RH) and corrected using an empirically generated calibration factor. Although preliminary, it may be possible to implement this method in maintenance shops to monitor emission trends and to compare emissions of various vehicles in a fleet. Such data will be useful for fleet planning to meet new air quality standards.

By Forrest T. Moyer

Frequency rates of injuries per million man-hours of exposure were improved during 1965 slightly to moderately over those of 1964 at metal mines, nonferrous reduction and refining plants, nonmetal mills, stone quarries and mills, sand and gravel operations, and slag operations. However, at metal mills and nonmetal mines the rates of occurrence of work injuries were less favorable. The severity rates of injuries during 1965 were better than in 1964 at metal mines and mills, stone quarries and mills, and slag operations. Conversely, severity rates were worse at nonferrous reduction and refining plants, nonmetal mines and mills, and sand and gravel operations.

Jan 1, 1966

By D. T. Holmes, W. G. Sandell

"INTRODUCTION Three representative lots of ore wore obtained from the Aguila minim district in Arizona during the Bureau's exploration of manganese deposits there. Since only selectively mined ore from this district will meet commercial-grade specifications, the ores were studied to determine their amenability to concentration.Although the purpose of the investigation was to determine the possibilities of the district as a source of commercial-grade manganese, testing was sufficiently comprehensive to indicate the response of the ores to several different types of treatment. Many data of secondary importance have been omitted, end only the more pertinent tests are presented in detail.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to. Metals Reserve Company was ferro-grade manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., O.18 percent; Al12O3, max., 6 percent; Zn, max., 1 percent.Later the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.O percent iron, and. 11 percent silica plus alumina. Premiums were paid for manganese con¬tent over 48 percent and iron content under 6 percent, penalties being imposed upon products containing loss than 48 percent manganese or more than 6 percent iron or more than U. percent. silica plus alumina.. The specifications for commercial manganese further required that the maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined.."

Aug 1, 1948

By Richard Mainiero

In any construction project involving explosives, care must be taken to protect workers from carbon monoxide (CO) generated by blasting operations. CO is an odorless, colorless gas that can cause illness and death by asphyxiation. In general, the first symptoms include headache, fatigue and lightheadedness. At higher exposures to CO, skin flushing, rapid heart rate, and lowered blood pressure occur. At ever, higher exposure levels, decreased attention span is followed by nausea, vomiting, unpaired coordination, fainting, coma, convulsions and, finally, death. The detonation of explosives in blasting operations generates a range of toxic fumes, but CO is the most insidious because it is colorless, odor less, and is long lasting, since it is not readily removed try reaction with ground water, soil or rock. Additionally CO is generated in relatively large quantities compared to other toxic: fumes. CO may continue to seep out of blasted material long after the odor commonly associated with detonated explosives has dissipated. It is never safe to assume as confined space in the vicinity of a blast is clear of toxic fumes. CO may be present even if the area looks Clear and many hours have passed since the last blast.

Jan 1, 2000

By Lyman C. Hitchcock

The objective of this program was to determine the minimum luminance requirements for underground coal mining work from the working face to the first transfer point. The resulting data encompasses 114 visual tasks from conventional continuous and longwall mining methods representing the salient visual tasks found in the jobs listed. Cutter Operator Roof Bolter Face Drill Operator Airdox Operator Longwall Jackman Shuttle Car Operator Loader Operator Shot Fireman Continuous Miner Operator Longwall Head Conveyor Operator Longwall Tail Conveyor Operator

Jan 1, 1973

By Gary E. Sherman

Preliminary economic mining feasibility studies were conducted by the Bureau of Mines to estimate mining costs in the Juneau gold belt area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of two mineral deposit types: (1.) Berners Bay vein gold deposits, and (2.) stockwork gold deposits containing gold, silver, and lead. Cost estimates were developed using the Bureau of Mines Cost Estimating System (CES). Discounted cash flow return on investment (DeFROI) was calculated using the Bureau's MINSIM computer program. Underground mining of a Berners Bay vein gold deposit was found to be economic (15 pct DCFROI) at a recoverable metal value of $353.67/mt for a 100 mtpd shrinkage stoping mine with a 10 yr mine life, $324.76/mt for a 20 yr mine life, $138.63/mt for a 500 mtpd longhole stoping mine with a 10 yr mine 1 ffe, and $127.50/mt for a 20 yr mine life. Block caving mining of a large stockwork gold deposit was found to be economic at a recoverable metal value of $15.28/mt for a 18,000 mtpd mine with a 20 yr mine life.

Jan 1, 2011

By S. P. Sandoval

The U.S. Bureau of Mines investigated the separation of aluminum from copper dump leaching liquors using a supported liquid membrane. Aluminum was selectively transported through porous polypropylene impregnated with di (2-ethylhexyl) phosphoric acid in an aliphatic diluent. The effects of variables, such as solution composition, temperature, and extractant concentration, were measured with a three-level fractional factorial experimental design. Experimental results were used to derive equations for predicting transport rates for aluminum, iron, and copper. The major variables influencing aluminum transport were solution temperature, feed solution pH, aluminum concentration in the feed solution, and extractant concentration. Copper and iron transport rates were almost zero when aluminum transport rates were high. Measured aluminum transport rates under the best conditions of 55° C, pH 3.0, 16 g/L A13+, and 65 pct extractant solution confIrmed the predicted value of 210 f.'g/(cm2.h). Transport rates for iron and copper were less than 5 ug/(cm2.h) under these conditions. Aluminum was recovered from the stripping solutions by sparging with gaseous hydrogen chloride to crystallize aluminum chloride hexahydrate, which was calcined to alumina. Sparging crystallization regenerated the stripping acid for recycle.

Jan 1, 1989

By G. H. Damon

Since 1963, Bureau of Mines Information Circular 8179 has served the mining industry as a fundamental safety guide in the field of blasting agents. In the intervening 14 years, many changes have occurred, and this report presents revised and new recommendations which recognize these changes. For example, AN-FO is now supplied mostly premixed, whereas in 1963 much of it was mixed by the blaster; aluminum metal (A1) and other fuels are now often added to AN-FO to increase strength, and flake aluminum powder is used as a sensitizer in water gels; and water gels or slurries that are now extensively used were just coming into practical use in 1963. To provide the widest possible margin of safety, some of the Bureau's recommendations are more stringent than existing regulations,

Jan 1, 1977

By G. S. Scott

[The Duretiu of Kinen, as :) pr<r"Yof its :;encr:rL propan clealini: with the causes, behavior, n.ncl tor-trol of o1:t1?;.?cite-mine fires, hns investic:&apos;lte3 I varionr. Te:.nr, for Je tec tin:: iccj.r)ic:~ t he;, tint; :,:.zqdergro-.:rid and of <~e termining the trend of the hen tir..: once -I i&apos;i re j 7 knnm tr, he nrcsc~t.]

Jan 1, 1938

By G. S. Scott

[The Duretiu of Kinen, as :) pr<r"Yof its :;encr:rL propan clealini: with the causes, behavior, n.ncl tor-trol of o1:t1?;.?cite-mine fires, hns investic:&apos;lte3 I varionr. Te:.nr, for Je tec tin:: iccj.r)ic:~ t he;, tint; :,:.zqdergro-.:rid and of <~e termining the trend of the hen tir..: once -I i&apos;i re j 7 knnm tr, he nrcsc~t.]

Jan 1, 1938

By Paul Hatmaker

This paper covers briefly the particular field of dolomite and magnesium limestone; certain uses of high-calcium limestone are mentioned only to show more clearly the limita¬ tions of the magnesian rocks. Such a comparison is helpful because magnesium carbonate is essential for some uses; for others it is immaterial; and for many its presence in an appreciable amount is objectionable. Magnesium carbonate, occurring as a rock resembling limestone or dolomite, is described in United States Bureau of Mines Information Circular 6437, Magnesite. Other com¬ pounds of magnesium are described in United States Bureau of Mines Information Circular 6406, Magnesium Compounds (Other Than Magnesite). Limestone, geologically, is a rock composed essentially of calcium carbonate; commercially, however, the term may include dolomite and magnesium limestone.

Sep 1, 1931

By William C. Morel, Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publica- tion of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engin- eers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal--Today and Tomorrow. 9. Cost Engineering. 10. Hydrocarbon Processing and Petroleum Refiner. 11. Industrial and Engineering Chemistry. 12. Nucleonics. 13. 011 and Gas Journal. 14. Petroleum Management. 15. World Oil.

Jan 1, 1965

In 2001, 14,623 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). This was an increase of 210 mining operations compared to 2000. Almost half (49%) were sand and gravel mines, followed by stone (29%), coal (15%), nonmetal mines (5%), and metal mines (2%).

May 1, 2003

By John Nagy, Hylton R. Brown, Irving Hartman

"INTRODUCTION The tests described in this publication were planned to provide information on the explosibility of metal-powder dust clouds. This subject has become increasingly important because of the large quantity and variety of metallic powders now used for military and industrial purposes. To provide the increased amounts of metallic powders needed in the manufacture of munitions and to supply the demand created by the rapid growth of powder metallurgy, existing metal-powder plants have been enlarged, production schedules accelerated, and new plants erected. In some cases new methods of producing metal powders have been developed. This increased production and the development of new manufacturing methods have caused an increase in the number of metal-powder fires and explosions, with accompanying heavy loss of life and property. These have emphasized the need for information on methods of providing protection against hazards inherent in the production and handling of powdered metals. This paper gives results of laboratory inflammability and explosibility tests made to April 1, 1943, and is a progress report. Many descriptive details have been omitted purposely; they will supplied in a later publication, expected to be a Bureau of Mines bulletin."

Oct 1, 1943

By Eugene L. Grumer

High-expansion foam was applied to the flames of six fuels burning in a 1-foot-diameter tray. The flames of three hydrocarbon fuels were more readily extinguished than the flames of methanol, acetone, or unsymmetrical dimethyl hydrazine. The result is rationalized on the basis that heat transfer from flame to fuel surface is primarily radiative with the hydrocarbons and more largely convective with the nonhydrocarbons. INTRODUCTION Equipment for producing high-expansion foams has been developed by the Bureau of Mines to control coal mine fires.5 Recently such equipment has been redesigned for portability and has now been produced commercially for other fire-fighting applications. In May 1961, a 50-by 50-foot gasoline fire was extinguished within 2 minutes by a trailer-mounted foam unit that produced 12,000 cu.ft./min. of high-expansion (1,000:1) foam.6

Jan 1, 1962

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jun 1, 1997

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jan 1, 1997

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By Walter D. Holland

This study was undertaken to determine miners&apos; breathing zone concentrations of diesel exhaust components, to investigate any relationships between these concentrations and vehicle type, the presence of emission controls, vehicle usage, and ventilation conditions, and to make recommendations for monitoring and ventilation requirements. Twenty-four mines including two con l mines were surveyed. Sampling was done for CON, NON, SOx, PNA, aldehydes, and particulates. hi most mines, concentrations of at least one contaminant exceeded one half the standard or TLV. The concentrations of gases arc probably sufficiently reduced by a minimum air velocity of 50 fpm. A sufficient reduction of particulate concentrations may require as high as 400 fpm air velocity. Vehicle age, type, or usage appear to have little or no effect on contaminant concentrations. PNA levels were below detection limits in all but a very few samples. Minimum requirements for routine monitoring should include formaldehyde, COx, NO2. It is further recommended that better definition of the minimum ventilation requirement be obtained.

Jan 1, 1978

By D. R. Dolinar, A. T. Iannacchione

Limestone formations in the United States can be subject to relatively high horizontal stresses owing to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rock fall hazard. Rock falls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings has an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orienting the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and off-setting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.