Search Documents

By Edward Fitch

The DOE is evaluating Yucca Mountain, Nevada as a potential site for disposal of high level nuclear waste. Yucca Mountain is located approximately 160 km northwest of Las Vegas on the western edge of the Nevada Test Site and the Nellis Air Force Range. An exploratory tunnel has been constructed through Yucca Mountain for site characterization. A controlled drilling and blasting technique, smooth wall blasting, was used to excavate the TBM starter tunnel and alcoves off the main tunnel to provide areas for scientific investigation. Fundamental to the blasting program has been the use of two blast design equations used in concert to minimize blast damage to the surrounding rock mass. The first of these equations was developed by Roger Holmberg and estimates near-field peak particle velocity that is the basis for minimizing blast damage to the host rock. The second of these equations was developed by B. H. Sanden and provides bore hole pressure estimation which allows controls to minimize crushing of the rock mass along the perimeter yet allowing enough force to create tensile failure between perimeter bore holes. This is key to the smooth wall blasting technique. To date, essentially the same controlled drilling and blasting program has been in place for all excavation requiring controlled drilling and blasting at the ESF. The controlled drilling and blasting program uses an iterative process to achieve continuous improvement in the blast rounds. This involves interaction between Architect and Engineer (A/E), Constructor, and Testing Coordination O&e (TCO) to ensure each blast round successfully meets the expectations of affected participants. The A/E requested that the TCO provide validation of the near-field peak particle velocity estimation under the Construction Monitoring Program. Data gathered under this program were reduced by statistical analysis and used to verify blast design parameters and provide a site specific blast damage relationship.

Jan 1, 2000

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By A. Cobbii, M. Kasliki, W. Birchi

The Department of Mining and Mineral Engineering at the University of Leeds has a long history of research into the environmental impacts of blasting from quarries and opencast mines. This paper gives an outline of a detailed case study into the structural damaged induced in a rock walled tunnel with a brick lined crown due to close proximity quarry blasting. The test site Taffs Well Quarry is located in South Wales in The United Kingdom and has a disused railway tunnel situated within the south eastern comer of the quarry site. Quarry development plans included the working of this area and therefore the deliberate destruction of the central section of the tunnel.

Jan 1, 2001

By D T. Froedge

Before this study was started, literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast-induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom of wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet.

Jan 1, 1983

By D E. Siskind

The Bureau of Mines performed a comparative study of nine sites at eight surface coal mines to determine if the presence of near-surfaced underground abandoned workings resulted in the generation of adverse long-duration, low-frequency blast vibrations. Six of the nine sites had underlying workings, and two had thick layers of low-velocity unconsolidated surface material.

Jan 1, 1990

By Roger L. Keller

This paper covers the design and test blast procedures for several drop shafts and edits leading to the completion of a recent Rochester Pure Waters Expansion Project . Due to the projects "in-town" presence, and its close proximity to many sensitive vibration sites, very stringent ground vibration limitations and guidelines for blasting were places on each site.

Jan 1, 1991

Blast performance is related to rock structure and strength, as well as to factors such as site geometry, drill patterns, explosives loading, firing sequences and delays.

Jan 1, 1986

By Paul Worsey, Richard P. Ayres, Mark F. C. Schmidt

A new alternative technique designed to reduce rock scatter and flyrock during boulder blasting is being developed at UMR. The method uses small explosive charges and is designed for shooting in close proximity, while utilizing common blasting products found on the operators’ site. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique was published in last year’s proceedings. This particular portion of the work was performed as an undergraduate research project as part of the requirements for the explosives emphasis degree option at UMR. Previous model work was performed using cubes of concrete. However, in real life boulders are often flat and irregular rather than perfect cubes. The purpose of this work was to determine how to deal with flatter boulders. The work comprised using different geometry blocks (simulated boulders) of the same volume (1 cubic ft.). Square concrete boulders using an 8.5bag concrete mix were cast using different width to height ratios (varying from 1: 1 to 3.7:1). Single 5/8 inch holes were drilled to 2/3 the depth of the blocks, charges placed approximately l/2 way in to the holes and the holes filled with water. The explosive charges comprised ICI Masterdets containing a OSg High Explosive base charge and incremental added weights of C4 explosive. In the experiments, the block height was progressively reduced and to compensate the charge weight was increased until acceptable fragmentation was achieved. It was found that a significant increase in charge wt is required to achieve the same fragmentation as the width to height ratio increases (the boulder becomes flatter). Furthermore, the increase in charge weight required is proportional to the width to height ratio. Basically, you have to use a higher powder factor for flatter boulders.

Jan 1, 2000

By Roger E. Scholl

Data on off-site low-rise building damage from underground nuclear testing at the Nevada Test Site (NTS) of the United States Atomic Energy Commission (AEC) [The AEC has been called the United States Energy Research ant Development Administration (ERDA) since 1975, but because the data presented here were gathered between 1966 and 1970, the AEC rather than ERDA is referred to in this paper.] are available for seven large tests in the period from 1966 to 1970. The data, while sparse, provide an adequate sample for the investigation of motion-damage relationships. Damage in the study is statistically described in terms of the incidence of damage complaints, the incidence of buildings damaged, and damage cost. Using 5%damped response spectrum acceleration amplitude to characterize ground motion, the plotted data fit reasonably well with previous motion-damage relationships established from extensive data available from the 1969 RULISON underground nuclear explosion (UNE) experiment conducted in western Colorado.

Jan 1, 1976

By Jorge Cárdenas, Piero Mejía, Diego Gamarra

The present case study details the solution to a complex situation in a mining operation, involving the challenge of expanding the tailings storage facility in high-criticality areas adjacent to electrical rooms that provide continuous power to the entire mining process, including water pumping and drainage systems. For this purpose, blasting is required to prepare the construction areas for the new expansion facilities. Upon deciding to proceed with blasting, a comprehensive engineering assessment was conducted to ensure operational continuity without impacting the process, while generating sufficient fracturing in the rock mass to allow extraction with auxiliary equipment. Support from specialists through the Technical Assistance area was requested, and a detailed evaluation was carried out through advanced studies. Field vibration studies were conducted to define attenuation models and characterize the rock mass in the sector. With this information, simulations were carried out using predictive and probabilistic models with Monte Carlo methods to select delay charges and optimal timing for reducing vibration levels and increasing frequency levels. With these measures, the three blasts conducted near the Gas Insulated Substation room, which had distances ranging from 30 to 100 meters, produced the following results: • Vibrations; The three blasts conducted at distances of 100, 30, and 50 meters recorded vibration values of 5.3, 40.2, and 9.5 mm/s, all of which were below the maximum vibration level of 50 mm/s set by the projects area. According to the USBM RI8507-OSMRE standard, all values for Peak Particle Velocity (PPV) and frequency were below the permissible limits. • Flyrock; Through filming and post-blast inspection, it was confirmed that the ejections were within the safety zone. • Fragmentation; The results obtained showed a maximum overbreak size of 1.5 meters, allowing the broken material to be moved effectively.

Jan 21, 2025

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Simav Bargu, Savas Gorgun, Derya Kucukbrtem, Esat Tansev

Although many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing of a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects.

Jan 1, 2002

By John L. Floyd

One of the key factors that controls the overall profitability of surface operations is the required volume of excavated material. If the overall angle of final walls can be maximized the amount of material excavated will be reduced. However, as the slope angle becomes steeper the wall's factor of safety decreases. As a result, the development and implementation of efficient wall control blast designs becomes critical to achieving stable walls. Many site specific conditions should be taken into account when defining the methods that will be used to lessen blast induced wall damage. This paper will discuss the steps needed to properly evaluate the site and develop efficient designs. Four variations of wall control blast designs will be evaluated in terms of cost and performance. In addition, the paper will include the quality controls needed to successfully implement and refine the blast design.

Jan 1, 1998

By Gungor Tuncer, Ali Kahriman

This paper presents the results of ground vibration measurements carried out in Hisarcik Boron open pit mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 304 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 2 different types vibration monitors (1 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2006

By Changa-Ha Ryu, Hae-Moon Choi, Sang-Don Lee

The rock mass to be excavated is classified using data obtained from the initial site investigation, and the design of excavation and support is then made based on the rock class. Rock classification provides an empirical design with guidelines for tunnel support compatible with rock mass quality and the method of excavation. Although most clients provide standard patterns corresponding to each rock class, the patterns of drilling and blasting have only been used in estimating the excavation cost and not used in the construction stage. The purpose of the study presented in this paper is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing the country. Long hole blasting was tested in rock mass whose RMR value is over 60. The blasting results were evaluated by measuring degree of fragmentation, advance rate, muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a twolane highway tunnel.

Jan 1, 2005

By Joel Chipana, Roberto Laredo, Benjamin Cebrian

Ring blasting is a common production method in underground metal mines. As a drill and blast process, it presents particular features that do not correspond with bench blasting in open pit or underground mining.

Jan 1, 2017

By Jerry Newton

The bulk explosives industry is relatively young compared to how long explosives have been in use. It's been around for about forty years, about the length of a person's career. This period of explosives history has seen constant change. The type of product, the manufacture and the trucks that haul it have changed a great deal over the years.

Jan 1, 1997

By Shadrack Nuamah, Erik Westman, Bright Afum, Jesse Addy

Rock fragmentation is the most critical aspect of hard rock production blasting due to its significant impact on drilling and blasting costs and the economics of subsequent loading, hauling, and crushing operations. This study analyzes current cost trends in the drill and blast operations of an anonymous open pit gold mine and proposes cost-effective drill and blast geometric parameters. The investigation focused on one operational pit with provided design parameters for two shots, shot 1 and shot 2. Existing blast parameters and two additional proposed sets of geometric parameters were evaluated using the Kuz-Ram and Chung and Katsabanis fragmentation models to estimate mean fragment sizes. The results indicated that the proposed blast parameters produced estimated mean fragment sizes within the mine’s desired range (not exceeding 45 cm). Additionally, the explosive energy was utilized efficiently per in-situ material blasted. The proposed parameters increased the estimated total volume of in-situ material fragmented by approximately 14% for both Shot 1 and Shot 2 compared to the current parameters. Furthermore, adopting the proposed blast parameters could lead to significant cost savings. The evaluated total drill and blast cost savings were approximately 11% for Shot 1 and 12% for Shot 2. These savings stem from the increased efficiency and effectiveness of the blast operations, highlighting the potential for substantial economic benefits. This study demonstrates that optimizing blast geometric parameters will allow open-pit mines to achieve desired fragmentation, utilize explosive energy more effectively, and realize considerable cost savings in drill and blast operations.

Jan 21, 2025

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By John W. Brown

The purpose of this paper is to describe different methods of evaluating the performance of your current rotary blast hole drills. To properly evaluate a drill rig's performance you should include a competent driller, mechanic, rotary bit technician and a technician representing the manufacturer of the drill.

Jan 1, 1998

By Rolf R. Schillinger

Subject of the paper are blasting vibrations as sources of environmental molestations including acceptance level,complaint level and damage level as well. Besides, the subject shows a comparison of international regulations and their problematical aspects. In consideration of blast induced immissions the subject shows that human annoyance has become an important place in blasting works. It provides a solution proposal how to minimize environmental effects of blasting works.

Jan 1, 1996