Search Documents

By Paulo Couceiro, Juan Navarro

The impact of rock blasting fragmentation and heave on digging performance in open-pit mining operations is usually the first true indicator of blasting outcomes. Within the typical excavation cycle, the bucket loading time or instantaneous digging rate are the ones that present the strongest correlation with rock fragmentation size distribution, swelling, and shape of the muckpile, a part of rock mass hardness, equipment size, power, and others. As the efficiency of unit operations becomes increasingly important for long-term mining strategies, cost-effective approaches are needed to increase mine productivity. In this line, the performance of downstream operations, such as digging, hauling, and comminution, may be affected by the energy input in blasting. This requires a better understanding of the explosive’s energy role in such unit operations in order to drive consistent improvements. Therefore, this paper examines the impact of the explosive’s energy distribution on shovel diggability from production shots carried out with different explosives in an open pit gold mine, with the aim of modelling the interface between blasting and excavation.

Jan 21, 2025

By C. T. Aimone-Martin, V. L. Rosenhaim

Blasting near residential areas has become frequent in many locations throughout Brazil. It was deemed necessary by the authors to have a better understanding of how typical Brazilian structures respond to blast vibrations and compare this response to environmental forces that naturally act on these structures. Typical Brazilian structures are built with clay bricks and cement-mortar. Foundations comprise concrete beam perimeter walls and thin concrete slabs. Roofs are very heavy as they are construction with clay tiles over a wood frame. Typically, walls are cover with cement grout, spackling (or plastered) and then painted. Interior walls are made of clay bricks and mortar to divide in rooms inside the structures.

Jan 1, 2014

By O Omidi

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper reviews previous experimental information and presents the results of new tests conducted in small blocks constructed using a commercial grout. The effect of the delay on the average fragment size, coarse fragmentation and uniformity of fragmentation is discussed. Fragmentation was coarser at extremely short or extremely long delays, while a fairly constant average size was obtained at a variety of intermediate delays. Uniformity, defined as the slope of the fragmentation distribution through the average fragment size, was poor at short and very long delays and relatively constant at the intermediate delays. Some tests attempted to minimize the effect of gas penetration by lining the boreholes with copper tubes. When this was the case average fragmentation changed marginally, while uniformity was significantly affected by delay and was typically smaller than in the unlined tests.

Jan 1, 2014

By Kenneth Eltschlager

The Surface Mining Control and Reclamation Act of 1977 requires that blasting be conducted so as to prevent injury to people and damage to public or private property. The three adverse effects are flyrock, ground vibrations and airblast. Blasting close to people frequently results in complaints of annoyance or damage. Federal and State personnel are responsible for evaluating the validity of the complaint. The elements to be evaluated include: reviewing blast logs, inspecting the mine, inspecting the house, measuring ground, air and structure vibrations, and predicting vibration levels. Computer spreadsheets, with their graphical capabilities, will be used to show how data can be cross tabulated to verify data accuracy. Complete statistical analyses of vibrations require more powerful software to make vibration predictions. Once all available data are gathered and verified, a decision on the complaint can be made.

Jan 1, 2001

By W C. Brukle

Our title for this presentation could be taken in many ways. One course would be terrifying and that would be to cite incredibly bad practices. All of our votes/efforts should be for the reverse direction in which everyone does his/her best to keep their pit or working place free from hazards.

Jan 1, 1983

By J Edmund Hay, Harry C. Verakisl, Richard J. Mainiero, John J. Mulhern

As the first stage in the rulemaking process, MSHA prepared requirements for the approval and use of permissible explosives and blasting items in underground coal mines. These draft requirements known as "preproposals" were announced in the Federal Register in mid-1984. The draft requirements on the use of explosives were written as a revision to Title 30, Code of Federal Regulations, Part 75, Subpart N. The draft requirements for approval of permissible explosives including sheathed explosives for unconfined applications, approval of water stemming bags, approval of detonators and approval of blasting machines were prepared as Parts 15, 16, 17 and 25 respectively.

Jan 1, 1985

By Lewis L. Oriard

Some two million cubic yards of sandstone and orthoquartzite were blasted and excavated at Upper Stillwater Dam, located high in the Uinta Mountains in northern Utah. The material was processed to produce concrete aggregate for the construction of the largest roller compacted concrete (RCC) dam ever constructed, and one of just a few in existence. The dam cross-section is shown in Figure 1. The aggregate was sound rock produced from required dam foundation excavation and from a quarry located about 1/2 mile from the dam site. Representative compressive strengths of the sandstones and quartzites were in the range of 20,000 to 30,000 psi.

Jan 1, 1993

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By Laurence Neufville

Proper risk assessment and blast design are very desirable to the execution of a blast. Not only will this ensure that it achieves its desired outcome, but the probability of complaints and litigation will be reduced. Blasting engineers rely heavily on site-specific data for analysis and input to the blast design equations, and therefore data collection is critical to this process. The traditional approach to data collection is to carry out site-specific reconnaissance by visiting the site, but the time spent doing so can be reduced if a remote sensing approached is adopted.

Jan 1, 2009

By Paul Worsey, Braden Lusk

Differences exist between public perception of construction blasting and quarry blasting. In general, people are able to tolerate short term inconveniences much better than long term ones. The paper focuses on the public perception of quarry blasting in St. Charles County, MO. This expanding urban environment has seen new legislation targeting preexisting quarry operations that have been in place for many years. A survey was made comprising interviews conducted to gauge perceptions of persons with varying demographics. Interviews covered topics involved with quarry blasting and its reporting methods. The purpose of the interviews was to determine public perception of blasting and how best to report results of vibration measurements. The use of different, less technically complicated measurement scales for vibration and airblast was considered as an alternative reporting system. The question for the industry is, “Has our past haste in adopting complex scientific scales and units been detrimental to us?” In other words, are we reporting the correct things? For airblast, the decibel scale was evaluated against millibar in the public eye. Peak Particle Velocity was also compared to that for displacement. Current legislation in the county is based on complaint levels rather than damage criteria. The complaints most likely not only come from ignorance to the affects of blasting on structures, but also sparse understanding of the units used to report these affects. The past practice of treading softly as an industry has been proven to be a poor choice, and education of the public as well as lawmakers on all levels is necessary. The Mississippi Valley Chapter of ISEE has begun to conduct seminars to this end. One educational seminar has taken place for officials and lawmakers in the St. Louis area, and others are in the planning stages. The focus of this paper is to gauge perception of the damage criteria reported today, and locate focal points for future education of the public in rapidly expanding suburban environments.

Jan 1, 2005

By K Taylor

Small scale tests have been conducted in blasting vessels in the laboratory, where the effects of explosive composition, charge diameter, explosive confinement as well as additives to the explosive were examined on NO, NO2, CO and CO2 production. Fumes were analyzed continuously using a flue analyzer, providing analysis every 15 seconds. The results were compared to previous work conducted in the laboratory and to literature findings. It was found that the type of the explosive was the most dominant factor with emulsion explosives producing significantly less amounts of toxic gases. ANFO was shown to always produce nitrogen oxides, even when fuel rich. Tests were also conducted by detonating explosives in broken rock, simulating the release of products of detonation during the formation of a muckpile. Products of detonation were affected by the presence of atmospheric air or rock around the charge. Gaseous products of detonation migrated through the rock piles at different rates, resulting in a change of toxicity values over time. In the small scale experiments, CO appeared to travel faster than CO2 while NOX was not identified. Analysis of the gases that were released during digging, several hours after the blast, resulted in high temporary concentrations of toxic fumes.

Jan 1, 2014

By Jhon Silva-Castro, Russell Lamont

Understanding the behavior of materials subjected to high strain rate conditions is of fundamental importance to the mining industry. Several stages of the mining process involve high speed loading rates including blasting, scraping, comminution, etc. Technical comprehension of how rocks deform, fracture, and fail under these loads is a fundamental first step required prior to any serious attempts at optimization of the energy utilized for pertinent activities in the mining process. A Split-Hopkinson Pressure Bar (SHPB) was designed and constructed at the University of Kentucky to study the dynamic properties of various types of rocks.

Jan 1, 2017

By Marcia Harris, Richard Mainiero

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

Jan 1, 2004

By R Vuolio, B A. Jonsson

In the center of Helsinki - capital of Finland - extensive blasting operations were carried out during the years 1982 - 84. At the corner of the streets Mannerheimintie and Simonkatu - in the Forum block - about 125,000 cu.m. of rock were blasted to give place for a new modern shopping centre (Fig. 1). Added to this amount of rock another 10,000 cu.m. were blasted for a transport tunnel to an adjacent underground bombshelter (Fig.2) which is to be used as a parking place in peace-time. The blasting work was demanding and difficult to carry out due to old buildings surrounding the work-site as well as computers and other sensitive equipment installed in some of them.

Jan 1, 1985

By H. R. Maggard, C. M. Bollinger

Solving the problem of detecting underwater explosions from "dynamite fishing" can be done by using a system of sonobuoys programmed to detect the acoustic waves from underwater explosions. The system includes three anchored sonobuoys, which have radio communication to a central station. Each sonobuoy will detect the direction the blast occurred, and then send the magnitude of the acoustic waves and the blast direction to the central station where the blast distance will be calculated. The central station can the send the coordinates to the authorities who can find the location using GPS systems onboard their boats.

Jan 1, 2004

By Roy McKinstry

In March of 2001, Barrick Goldstrike became the first surface gold operation in North America to evaluate the advantages of electronic detonators. A detailed study was conducted to quantify the benefits of the use of electronic detonators to the downstream excavation, crushing and ore processing operations. The following methods were used to quantify blast performance: High speed film and video monitoring Firing time and rock response analysis of the high-speed films Digital fragmentation analysis of the post blast muckpile Vibration waveform analysis (including Fast Fourier Transforms and seed waveform modeling) Excavator performance quantification Crusher, SAG mill and ball mill performance evaluation Ore recovery analysis Cost/benefit analysis

Jan 1, 2002

By S. Nakamura, H. Taniguchi, K. Noguchi, H. Sugihara, T. Matsuzawa

It has been reported that expanded poIystyrene and ANFO prills ‘were mixed on a blasting site for controlled blasting (ISANOL). Although there seems to be few possibility of their segregation because mixing on a blasting site is done, there is a great possibility of segregation in packing, transportation and loading of the product due to the different densities of the two ingredients in Japan where mixing on a blasting site still remains inoperative. The fiee-flowing property of ANFO prills was lost with the passage of time because the Abel oil infiltrated into the expanded polystyrene and that gave the product high viscosity.

Jan 1, 2001

By Brent Blanchard

The use of explosives to safely fell structures can be traced back over 300 years. Since then, dozens of chemists, inventors, blasters and demolition experts worldwide have played prominent roles in the evolution of what has become the modern-day explosive demolition industry. In America, one of the earliest applications of explosive demolition occurred in response to the great fires of San Francisco, where homes and businesses were blasted with gunpowder in a desperate attempt to create firewalls. Later in the 19th century, inventions such as nitroglycerine, dynamite and blasting caps made structural blasting a safe, efficient alternative to conventional demolition methods. The 20th century brought the first experiments in shaped charge technology, and this, combined with developments in portable seismology and non-electric delay systems, allowed an ever-expanding variety of structures to be explosively felled by demolition experts throughout the country. The 1950s and .60s brought a new wave of commercial structural-blasting entrepreneurs (several of whom are still active today), and their efforts towards improving adjacent-structure protection and public relations beget the felling of large commercial buildings in dense urban environments. By the late 1980s, publicity-driven motives were gaining greater influence in the decision to .implode. various structures, and the transformation of blasting operations into promotional spectator events played a role in several injuries and fatalities. Since that time, however, a renewed sense of responsibility practiced by most blasting firms and project officials has resulted in the safe, successful completion of hundreds of recent endeavors. In sum, what appears today as an efficient, economical - and visually spectacular - way to demolish structures has its roots in developments of the past several centuries

Jan 1, 2002

By Ricardo Dr. Chavez, Mathieu Lachamp, Rob Dr. Farnfield

Pueblo Viejo is an open pit gold mine in the Dominican Republic which is always looking forward to implement the newest technology in the industry to improve all processes. Focusing on one of the pillars of the department and our company, digitalization, we’ve been looking for the technologies that allow us the automation of data generation, supervision and process innovation. That’s where a new Drill and Blast software takes place, helping to integrate the process from the beginning to end, right after the pattern is designed until it’s blasted, allowing us to track results like vibration, fragmentation, performance, cost and inventory of each blast in a single platform. The software helps engineers to generate back analysis by blast, bench, pit, month and many other ways, in a timely friendly manner. Therefore, we can catch business opportunities and improvement for the drilling and blasting process.

Jan 1, 2019

By James Stuart

A man died when the primed charge he was holding against his chest exploded. He was doing legitimate explosive work, and he was following all the safety procedures he had been taught. He and his colleagues had done this, thousands of times previously, with no ill effects.

Jan 1, 2007