Search Documents

By Jim Pae Lem

This study investigates the mode of occurrence of uranium in a copper concentrate from the Prominent Hill mine. Mineralogical and liberation studies of a high grade Cu concentrate (monthly composite) containing uranium (U) were undertaken using QEM-Scan in combination with QXRD and ICP-MS. The study aimed at determining in what form U was recovered, and by which mechanisms. The deportment of U was studied in 3 size fractions; +20µm, -20+8µm and -8µm. QEM-Scan analysis showed that uranium was present as U(Cu)-silicates, U-silicates, UPbOx/FeOx or traces of UThOx and UTiOx, with the U-silicates present across the size fractions. The association of uranium bearing minerals with copper sulphides varied across the size ranges. Interestingly, most of the U (46% by weight) was distributed in the finest fraction (-8µm), in which the deportment of Cu was low (6%). Over 40% of the U mineralisation in the -8µm was liberated. In terms of the floatation response, while recovery of the uranium minerals as a result of their association with copper sulphides (as composite particles) was evident, recovery of UPbOx locked in hydrophilic haematite in the +20µm size fraction suggests, that other mechanisms (e.g. Inadvertent activation by Pb from radioactive U decay) are possible. Furthermore, the high amount of fine liberated U bearing particles in the concentrate points at entrainment as another major mechanism for uranium recovery, and therefore, a target for process optimisation.

Sep 1, 2012

By Y. Tang

The paper studied the extraction characteristics of the fly ash from a location in Guizhou province. Under ordinary pressure, the fly ash is extracted by an acid and alkali, and then studied for its reaction characteristics with different extraction agentia, temperature, consistence and time. The results of acid extraction show that there are good reaction characteristics for Fe2O3 with HCl and the extraction rate decreases with the increasing of extraction time. There are good selective characteristics between Al2O3 and H2SO4 and they weaken with the increasing of temperature and the expanding of time. The best extraction results are shown with CaO and MgO because of their chemical characteristics and the over-saturation degree of the extraction processing. In addition, It?s found that it cannot leach all the substances from fly ash even with the higher consistence (10mol/L) of extraction agent, the longer extraction time (2h) and the higher temperature (100?) .It shows that the extraction rate of Fe2O3 is 82.81% and that of Al2O3 is 29.01%. The results of alkali extraction show that the extraction rate increases with the consistence of extraction agent and temperature, and the extraction rate of SiO2 by NaOH increases rapidly with the time expanding while that of Al2O3 falls gradually.

Jan 1, 2014

By R. D. Alorro

Melting has become a popular pre-treatment method for municipal solid waste (MSW) incineration residues in Japan. Although the method is effective in stabilizing the hazardous organic sub-stances such as dioxin, it concentrates the heavy metals such as Zn, Pb, Cu, and Cd in a newly formed fly ash (melting fly ash). Melting fly ash is classified as a hazardous waste because of the leaching potential of these heavy metals in landfill environment. Extraction and recovery of these metals seem to be more environmentally and economically attractive than disposing the material to landfill after immobilization process. This study proposes a Carrier-in-Pulp (CIP) method as a new hydrometallurgical route to reject and recover heavy metals from fly ash. In this method, a carrier material which recovers the extracted metals is added simultaneously with fly ash to leaching solutions and is harvested from the pulp by physical separation method like magnetic separation or sieving. To demonstrate the effect of CIP method, shaking flask experiments were conducted under various conditions using NaCl solution as lixiviant and iron powder or granular activated carbon as carrier materials. In the CIP method using iron powder, more than 97 wt% of Pb and Zn were extracted from the ash to the solution phase. However, the iron powder which was harvested from the pulp by magnetic separation, recovered only Pb (more than 94%) through cementation, leaving behind Zn ions in the solution phase. Due to this problem, granular activated carbon (GAC) was considered as an alternative carrier material. Single- and multi-metal adsorption experiments using granular activated carbon were conducted as a preliminary study. Around 85% Pb and 88% Zn were recovered by GAC in the single-metal adsorption experiment, while 60% Pb and 70% Zn in the multi-metal experiment. These results showed that activated carbon was superior to the iron powder since it was able to recover both Pb and Zn through adsorption. The leaching test conducted on the residue after the CIP-Fe treatment revealed that the solubilisation of Pb was successfully suppressed to meet landfilling guidelines.

Jan 1, 2014

By A. S. Choudhary

Most of the coal reserves in India are of drift origin and have very poor washability characteristics and a high level of near gravity materials. At least 30 new coal wash plants are expected to be set up in the next 5years.In such a scenario, adequate sampling followed by sink float test work for washability analysis becomes very critical for designing these new plants. For coal sampling purpose, stipulations of different standards are sometimes formidable and on the border of ?impracticality?; sometimes are self contradictory in terms of gross sample weight vis-a-vis minimum number of particles required in each size fraction and in each relative density fraction and also the minimum mass in the latter. Validation of the generated data is another important aspect of washability analysis. These issues can easily be addressed by using straight forward mathematical relationships, well known RR plots and by using simple MS Excel tool, etc.

Sep 1, 2012

By Matheus Tocchini, Henrique Kahn, Juliana Antoniassi, Carina Ulsen, Eldon Masini

"Sand and gravel are the second and third largest minerals in production in Brazil, and this is increasing noticeably. The extraction of natural sand from river beds is increasingly restricted and most of the sand used in large cities comes in from more than 150 km away, resulting in high transportation costs. As a result, it has become more common to use crushed rock as artificial sand. The main difficulties in this process are controlling the shape of the particles and the content of deleterious materials, such as mica. Within this situation, this paper presents an alternative to using artificial sand for concrete use. Our procedure involves the following steps: a) sampling sand from different production days, b) characterizing the bulk sample by particle size and shape distribution, chemical composition by X ray fluorescence and mineralogical composition by X ray diffraction, c) removing fine grains by air classifier, d) performing intensive attrition with high pressure washing and e) characterizing products. The results demonstrated that this sample contains a huge proportion of fine grains and a notable content of mica, which is distributed along all sieve fractions. The presence of mica makes the use of sand in concrete unfeasible, moreover scanning electron microscopy analysis demonstrated that this phylossilicate is finely grained and associated with coarse fractions. Thus, the removal of fine fractions made possible a partial reduction in mica content. Furthermore, intensive attrition demonstrated that the procedure was efficient to remove most of the mica while also reducing sharp edges, which improved the shape of these particles."

Jan 1, 2014

By W. H. Cheung

Nickel and cobalt production relies heavily on the processing of nickel laterite ores; these ores contain the majority of known Ni and Co reserves, 80% and 90% ~ 95%, respectively. The Caron process is used to extract Ni and Co metals from low-grade nickel laterite ores (1% Ni and 0.1% Co). It involves selective reduction of NiO and CoO minerals followed by ammoniacal leaching. Despite low metal recoveries, this process continues to be technically and economically reliable and thus commercially important globally. However, keeping the Caron process cost-effective has been a challenge for industries because of increasing economic and environmental pressures. Although studies of the Caron process have been extensive, significant improvements in recoveries of industrial processes have not been forthcoming. Reported industrial metal recovery from high iron content ore is only 80% ~ 85% for Ni and only 40% ~ 45% for Co; recovery is even lower for ores rich in magnesium. The real difficulty here is that there is no complete understanding of and control over the complex series of reactions in the ore and in the leaching solution during processing. Achieving effective metal recoveries from the Caron will require control of the mineral transformations, which affect the activation of minerals by reduction. In this study, the effect of over-reduction was investigated, which superseded the effect of activation by lowering the activity of the minerals and thus metal dissolution. Reduction was carried out in a batch reduction apparatus with 1:1 and 1:2.5 CO/CO2 gas mixtures from temperatures of 500 ~ 700°C and residence times up to 60 minutes. The pre-reduced ores were leached using a standard ammoniacal leaching test. Thermodynamic analysis and possible effects of stable phase field on leaching was examined. The results suggest that control of over reduction effects are directly related to the mineral transformation and reduction conditions.

Jan 1, 2014

By Sudarshan Martins, Peter Radziszewski

"Tumbling mills are machine, operating in non-equilibrium, capable of applying forces on the ore contained within, causing the ore to break down. The action of the mill on the ore is very inefficient, producing a large quantity of heat. The inefficiencies of the mill drive the desire for improvement, spawning research and development activities. Given the non-equilibrium nature of the mill, the theory of Large Deviations is proposed as the framework that captures the state of the mill. The theory of Large Deviations allows for the determination of the rate function and the scaled cumulant generating function (SCGF), for systems in either equilibrium or non-equilibrium. Powerful connections can been made between familiar concepts of statistical physics and the concepts introduced by the theory of Large Deviations: entropy can be associated with the rate function; the scaled cumulant generating function with the free energy. It is shown that observables, compatible with Large Deviation theory, can be identified for the tumbling mill. Here, the time series of the energy associated with an element of the charge is such an observable. Furthermore, using some experimental data, it is shown that the time series of the energy can define a rate function, thereby describing the system within the Large Deviation framework. Finally, a discussion of the results is given, particularly how this theory can be further developed for tumbling mills."

Jan 1, 2014

By X. H. Li, F. Xie, Q. Zhang, Z. H. Shen, S. Mao

"There is abundant rare-earth element(REE) in our country, but it is very fragmented in the earth's crust, and it is very difficult to mining or mining cost is extremely high. There are few of industrial value rare-earth deposits. There is a lot of concomitant rare-earth deposits, and the comprehensive utilization value is high. There is very rich carlin-type gold resource, associated with a certain amount of REE in the southwest of Guizhou province. In order toutilize comprehensively the resources, this paper conducts the study on the occurrence characteristics of REE in the ore. By the chemical analysis, the gold grade is 3.35g/t, the organic carbon 0.81%, the total REE 0.022%, which is a high carbon fine disseminated gold ore. By the optical microscope and XRD analysis, the major minerals are quartz, pyrite, calcite, limonite, arsenopyrite, mica, kaolinite, clay minerals, etc. In addition, there is a large amount of carbonaceous materials, such as organic carbon, graphite, which is harmful on leaching of gold. By the scanning electron microscopy analysis, there are thorium, lanthanum and neodymium, ytterbium, persimmon and other REE in the ore. Gravity separation shows that REE could be enriched to lighter material mainly, which indicates that REE disseminate closely with lighter materials.INTRODUCTION Carlin-type gold ore is important gold resource in the world, which are mainly distributed in Nevada and its vicinity, as well as the two Golden Triangle of Yunnan, Guizhou, Guangxi and Sichuan, Shanxi, Gansu province in China(Su W.C. et al.,2009; Xia G.X.,1996).Guizhou carlin-type gold ore is the second largest gold resource in the world(Muntean J L et al.,2011), distributing along the southwestern margin of the Yangtze plate, mainly mineralizing in the neopaleozoic-early mesozoic(Xie Z J et al.,2017). Many large gold deposits have been found in southwest in Guizhou in twentieth century, such as Zimuyou,Getang, Lannigou, Shuiyindong and Laowanchang gold deposit, and so on, and the gold reserves reach over 100 tons(Xia Y. et al.,2009).There is a certain amount of rare-earth resource in the carlin-type gold ore in the southwest in Guizhou province, and the current researches might mainly focus on characteristics of REE from the angle of geological mineralization(AnanyevY.,2015), not from the angle of separation and enrichment."

Jan 1, 2018

By J. Wiese, K. Corin, Z. Song

"Relating flotation performance to the electrochemical characteristics of a pulp is complex both in fundamental research and in practice. In the case of thiol collectors, different Eh values in the flotation system can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system. A variation in pulp potential may also be achieved by the addition of potential modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). There exists anecdotal evidence which suggests that the addition of small amounts of H2O2 to the flotation process can improve sulphide mineral recovery. The objective of the present study was to investigate the effect of the addition of the potential modifier, H2O2, on sulphide mineral recoveries and grades in the flotation of sulphide minerals from two copper bearing ores from China and compare the results to those obtained for a PGM bearing ore South Africa. Batch flotation tests were conducted using the three different ores at the natural pH of the different systems, in the presence of a xanthate collector and the absence and presence of H2O2 as a potential modifier. The results indicate that the addition of carefully controlled low concentrations of H2O2 resulted in improvements in flotation performance. INTRODUCTIONElectrochemical potential as a control parameter in the flotation of sulphide minerals has been widely studied (Allison et al., 1972; Gardner and Woods, 1979; Ross and Van Deventer, 1985; Chander, 2003; Woods, 2003; Javadi, 2013). There is concensus that in order to be recovered during flotation, sulphide minerals require a suitable redox environment. During the flotation process thiol collectors and sulphide minerals are involved in electrochemical reactions which result in the formation of hydrophobic species at the mineral surface (Finkelstein and Goold, 1972; Rand and Woods, 1984). Sulphide minerals act as semiconductors and electrons are transferred during the interaction of the mineral with collector. The resultant potential difference and its magnitude are responsible for the transfer of electrons and the rate of the reaction (Bard and Faulkner, 2001; Fuerstenau et al., 2007). Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, may be manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system (Heyes and Trahar, 1979). The use of potential modifiers viz. reducing or oxidizing agents which include H2O2, NaClO, and NaHS, is an alternative method by which to control the potential of the pulp in a flotation system which may or may not promote the flotation of desired minerals (Rao, 2004). The oxidizing agent, H2O2, undergoes a cathodic reaction which can result in the enhanced flotation of valuable minerals. The potential of the system is increased which results in a shift in the mixed potential of a mineral. The magnitude of the over-potential influences the rate of the oxidation process and thus the flotation response of sulphide minerals (Kocabag and Guler, 2008). Equation 1 shows the proposed oxidation of xanthate by H2O2 (Lipkina and Streltysn, 1970)."

Jan 1, 2018

By G. Aguilera

It is known that an addition of rigid particles into a fluid medium changes the flow field. Therefore, the rheological behavior of suspensions will be hardly Newtonian, such as their continuum phase. This phenomena was studied by Einstein in 1906 (Einstein, 1956) for the single case of spherical particles in a continuum liquid of a very dilute suspension. The final analysis applied for suspensions was derived from the evaluation of the behavior of ideal gases, finding a simple expression for the viscosity of the dispersion. All the following works about the hydrodynamics of suspensions at low and high solid contents was based in the Einstein´s model. For clay minerals suspensions where the physical and chemical properties of the particles are complex, it was found that the Einstein´s model is not a good approximation, even so for the most dilute dispersions. The present paper shows a new approximation that describes the non-Newtonian behavior of the suspensions of clays, and the attempt of understand how the different fine sizes, shapes and physico-chemical properties of clay particle surfaces give specific characteristics of plasticity, viscosity or visco elasticity to suspensions. Keywords: viscosity, clay minerals, einstein´s model, dilute suspensions

Sep 1, 2012

By M. D. Kaizer

PETROBRAS started its Oil Shale process development in 1953, the PETROSIX process which was developed and tailored to Irati Oil Shale formation. Since 1991, the industrial plant called MI (Industrial Module) has been operating, producing more than 20 million barrels of oil. In order to continue the oil shale exploration, a new shale mine is been opening. This article reports the planed measures taking in order to limit the environmental impacts and to return the land as close as possible to the original condition, as well as with the disposition of the process waste and the city garbage. It shows that the remediation process starts during the mining activities and continues after the mine exploration. Another characteristic of the Petrosix process, the pyrolysis of tires will be focused.

Jan 1, 2014

Mineral processing is an energy and water intensive activity. Mill comminution equipment usually has high energy requirements which necessitate extensive cooling to remove heat. Cooling requirements are typically 10% to 20% of the comminution energy. If there is an adequate supply of suitable water, open water-based cooling systems are the simplest, cheapest and most energy efficient cooling method available. This paper describes a method to determine the water demand for open water-based cooling systems at a plant and to determine whether the mine has sufficient water to meet that demand.

Jan 1, 2014

By C. Y. Sun

China is a country with abundant resources of tungsten, taking one of the world?s top-positions regarding both the total reserve and the amount of industrial production. China?s tungsten resources occur mostly in multi-metallic deposits rather than in single-metallic deposits. China?s multi-metallic tungsten ores have the characteristics of coexistence with other valuable components such as molybdenum, bismuth, copper, sulfur and fluorite. These ores are usually low in grade and difficult to process. The technological challenge in mineral processing lies in separation of multi-metallic components in these complex ores and a comprehensive utilization of natural resource. Several cases of industrial practice of processing China?s typical multi-metallic tungsten ores are presented.

Jan 1, 2014

By A. V. Kurkov

The secondary action reagents (SAR) are organic diphilic compounds capable of altering ac-id-base and donor-acceptor properties of the main collector and consequently the energy of collector interaction with the mineral?s surface, its hardness and fixation forms ratio through associates formation via the hydrogen bonds. When the basic flotation conditions are being established, convergence of the electronic structure of the collector and the mineral being extracted due to minerals surface preconditioning with modifiers and the most efficient collector choice. At the next stage of the selective flotation condition establishment SAR is selected for a more precise adjustment of the energy of the collector fixation on the mineral. Such an approach makes it possible to solve efficiently various issues of flotation separation of non-sulfide minerals. In particular neutral organic substances containing groupings C==O, S==O, P==O (ethers of carboxylic and phosphonic acids, amides of carboxylic, phosphonic and sulfonic acids) were proposed as SAR. In order to enhance the flotation process selectivity in the conditions of water recycling including the selectivity of carboxylic collectors especially in the environment of high hardness water flotation, it was proposed to use SAR with long hydrocarbonic radical and groups with enhanced electronic density within the molecule: N-methylolamides of alkylphosphoric acids and ethers of methylphosphonic acid. Introduction of small amounts of these compounds alongside with the main fatty-acid collector enhance the performance of fatty-acid flotation of fluorite, beryl, columbite etc., lowers the collector consumption, and completely compensates the depressive effect of recycled water. Di-2-ethylhexyl ether of methylphosphonic acid?CH3P(O)(OC8H17-i)2 (hexarane) was more thoroughly researched as such an agent within fatty-acid flotation process. Following aspects of the flotation system were studied: interaction of oleic acid and sodium oleate with hexarane in the liquid phase (infrared spectroscopy); heat emission under the interaction of hexarane-oleic acid ? sodium oleate ? calcium salts (isoperiboric diathermic colorimeter); colloid-disperse state of the collector influenced by hexarane (nephelometric analysis); dynamics of the mineral surface hydration due to the agents (method of indicator negative adsorption); hexarane effect upon the interaction of fat-ty-acid collector with calcium salts (complexometric method with Trilon-B); floatability of pure minerals (quartz, microcline, beryl, columbite) in Hallimond tube; hexarane effect upon oleic acid (sodium oleate) adsorption (nephelometric method for identification of the residual content of oleic acid and its forms within the solution). Upon the research it can be definitely concluded that the adjusting effect of such compounds as hexarane within the non-sulfide minerals flotation process is mainly determined by their interaction with the main collector both within the pulp and at the mineral surface with associates formation due to the hydrogen bond. The consequence is calcium oleates destruction with the release of the most active collector under flotation in hard water environment which determines the efficiency of hexarane joint application with fatty-acid collector under recycled water supply. Therefore the introduction of the class of secondary action reagents is supported by their operation mechanisms and flotation process function and determines a new approach to the development of efficient conditions of selective flotation separation of non-sulfide minerals.

Jan 1, 2014

By Tamal K. Ghosh

In this study, the QEMSCAN technology is used to acquire quantitative modal, textural, mineral association and liberation data on different products generated from with or without washing, fractionation by size and density using screens and heavy liquids/panning, which has provided significant information on the quality and beneficiability of four categories of low Grade iron ores from Jharkhand-Orissa region. The deposit of low Grade iron ore has been categorized into four categories viz. Grade-I with <45% Fe(t) a) containing shale rich type and b) BHJ rich type; Grade-II with 45-55% Fe(t) and Grade-III with >55% Fe(t) containing conventional flaky, hard, kanga, lateritic, shale and BHJ litho/ore types in varied proportions. Mineralogy is similar across all samples being hematite, martite, goethite, kaolinite and gibbsite. Banded Hematite Jasper has difficult liberation characteristics due to highly compact banded mode of silica mineral occurrence with hematite. In all categories, the grade dilution is by the presence of 1) ?Discrete gangue rich litho types? at lump size and 2) ?Within ore types?. The second type of grade dilution contains coating of gangue phases around the iron ore minerals and different degree of locking of gangue phases within iron ore minerals. Further characterization and beneficiation assessment details are discussed in this paper.

Sep 1, 2012

By Carsten Gerold

The paper is giving an overview about successful operating Loesche Vertical ? Roller ? Mills (VRM) installations and summarises the main benefits of the dry compressive Loesche grinding technologies in Airflow- and Overflow-Mode. Some of these benefits are optimised energy efficiency of the grinding - classifying - circuits, increased mineral recoveries and decreased OPEX costs, at a parallel simplification of the process route. Within this paper the process values of the Loesche VRM are compared to existing or planned conventional grinding ? classifying circuits. Further advantages discovered in pilot trials and examples for new more efficient process route alternatives are given. The paper reports about production and pilot trial experiences obtained by crushing and grinding Iron Ore, Iron Ore Concentrates, Copper Shale, Copper Matte, Copper Slag, Titanium Slag, Tin Slag, Steel and Stainless Steel Slag with Loesche VRM.

Sep 1, 2012

By W. L. Jiang

Reverse-flotation technology is often applied in iron ore dressing plant, in order to enhance the quality of iron concentrate from magnetic separation. However, this technology has disadvantages in operating cost, energy consumption, and environmental protection. Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate. This paper describes the development of Complex Flashing-Field Magnetic Cleaner, a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field. This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magnetic field, which can strengthen the formation of magnetic agglomerations and the dispersion of gangue minerals, improving the quality of separation. The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process. Test results showed that this equipment is reliable in operation, economically beneficial, and has large potential of application.

Jan 1, 2014

By T. Moloane, C. Bergman, Heloise Thiele

"A pilot test campaign was undertaken to evaluate dense medium cyclone separation efficiencies on samples of iron ore fines (-1mm +300µm). Evaluations were done using both gas and water atomised FeSi types across a range of operating conditions in the presence of slimes build-up. A Mineral Liberation Analyser (MLA) was used to measure size, density, shape and liberation data of DMS feed and products. The results of the test work were used to obtain parameters for modelling of the partition size/density response. The findings indicated that accurate density characterisation of the feed ore is essential in understanding product quality and recovery, particularly due to the effect of porosity and micro-inclusions. A significant off-set between cyclone underflow density and separation cut-point (D50) was found indicating that relatively low feed media densities (about 3.4g/cm3) are required to achieve high density cutpoints of over 4.0g/cm3. In agreement with CFD modelling, the separation quality is dominated by viscous effects, hence FeSi type and slimes content will need to be carefully controlled to ensure efficient separation.INTRODUCTION In the South African context, future resources of hematite are expected to be both of lower head grade and will contain a higher content of banded iron formation (BIF) (1). These ores may require finer crushing in order to liberate the high-grade fractions and will thus increase the amount of -1mm material to be processed. In order to efficiently upgrade these materials, it becomes necessary to re-examine both traditional and novel processes to treat material finer than 1mm in size. These include spiral and up-current classifiers, wet high intensity magnetic separation processes, Reflux classification and potentially includes dense medium separation (DMS). This study presents a technical evaluation of fines DMS using a mineralogically-based particle tracking analysis method (PTA) to calculate efficiencies of separation."

Jan 1, 2018

By T. Tsurata

The accumulation of thorium and/or uranium by various microorganisms from a solution containing thorium and/or uranium at pH 3.5 was examined. Among the species tested, a high accumulation ability for thorium was exhibited by strains of gram-positive bacteria, such as Bacillus megaterium, B. subtilis, Micrococcus luteus, Rhodococcus erythropolis, and actinomycetes, such as Streptomyces levoris. On the other hand, though uranium was accumulated in small amounts from the solution containing both elements by all these microorganisms, actinomycetes, such as S. flavoviridis and S. levoris had relatively high uranium accumulation abilities. In these high performance thorium- and uranium- accumulating microorganisms, S.levoris, which accumulated the largest amount of uranium from the solution containing only uranium at pH 3.5, could accumulate about 300 µmol thorium and 133 µmol uranium per gram dry wt. of microbial cells from a solution containing both thorium and uranium at pH 3.5. After this screening, uranium accumulation using microorganisms isolated from uranium mines, among which some strains of bacteria were found to possess an extremely high uranium accumulating ability. The microbial biomass may thus be considered for use as an accumulating agent for the removal and recovery of uranium that may be present in metallurgical effluents, mine tailings, seawater and other sources. Recently, hundreds of micro-organisms existing in uranium deposits located in North America, Australia, and Japan for their ability to accumulate large amounts of uranium, and found some new strains which accumulated large amounts of uranium, such as Lactobacillus and Bacillus sp. from Japanese and Arthrobacter and Bacillus sp. from the United States uranium deposits. These bacterial strains can accumulate about 2500 µmol uranium per gram dry wt. of microbial cells within one hour. These microbial cells can remove uranium from the uranium refining wastewater with a high efficiency. The accumulation of uranium from a solution (pH 5.8) by microorganisms contained Arthrobacter nicotianee, which is a similar strain mentioned above Arthrobacter sp., was examined. Among the 76 strains of 69 species tested (23 bacteria, 20 actinomycetes, 18 fungi, and 15 yeasts), high uranium accumulation ability was exhibited by strains of the bacteria, A. nicotianae, B. subtilis, and M. luteus. A. nicotianae cells, which showed the best performance, could accumulate about 698 mg uranium (2.58 mmol) per gram dry wt. of microbial cells.

Jan 1, 2014

By Chris A. Fleming

"The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative.There is arguably an even more compelling reason for mining companies to consider cyanide recycling. With the growing storm of negative public opinion that the use of cyanide in the mining industry is attracting - following several highly publicized spills over the last couple of years - the time has come for the gold industry to demonstrate environmental diligence and stewardship in the use of this commodity that is so vital for their industry. There is no doubt that the widespread implementation of cyanide recycling will reduce the impact of the cyanidation process on the environment, both by reducing the risk of spills (with less cyanide being transported from manufacturing plants to gold mines), and by reducing the loading of toxic and nontoxic metals and ions in the tailings.This paper briefly discusses the pros and cons of the different processes that are available for the treatment of gold plant tailings to regenerate and recovery cyanide for recycling, and presents a techno-economic argument for the incorporation of this technology into many gold plant flowsheets today."

Jan 1, 2003