Search Documents

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012

By Stephen J. Harker, John Knights, Randolph A. Pax, Glen A. Stewart

"Mineral samples were obtained from different stages of a mineral processing circuit used to extract the copper and gold rich mineralogical phases. The aim of this work is to characterise the quality of the samples at different stages of processing. The samples were taken of the head grade, tailings, cyclone overflow and the final concentrate.Characterisation of the samples was determined using Cu-Ka X-ray powder diffraction and Fe57 Mossbauer spectroscopy. These measurements will be presented and discussed in terms of the enrichment of the ore, showing the removal of magnetite and quartz through the processing, the final concentrate being rich in chalcopyrite and pyrite. This data also shows the utility of Mossbauer spectroscopy to provide mineralogical phase information directly.Mossbauer spectroscopy is a tool to determine the material phases of a sample. It is a nuclear based technique which measures the amount of attenuation of a narrow Doppler shifted source energy as it passes through a sample. The attenuation depends on the amount of resonantly absorbing material in the nuclear radiation path from the source to the detector. Synchronous detection of the doppler shifting velocity and the nuclear radiation count gives a Mossbauer spectrum. By convention, the energy axis of the Mossbauer spectrum is displayed in units of velocity.Figure 1 shows Mossbauer spectra obtained for a sequence of samples throughout a processing plant. These spectra show the removal of magnetite and the concentration of chalcopyrite and pyrite. Optical microscopy results indicated a significant component of bornite not witnessed with Mossbauer spectroscopy. Closer examination showed that optical microscopy assays over estimate the bornite component."

Jan 1, 2003

By I. N. Babich

"Complex technological problems associated with the processing of mineral raw materials require the search and development of new means and ways of thinking. At present, computer cognitive graphics (CCG) are one of the most actively developing areas of new information technologies. The aim of the study was to optimize the cycle of technological evaluation of ores at all stages of geological exploration of deposits on the basis of analysis of geological sampling data using CCG. A new approach has been developed that facilitates optimization of the whole cycle of subsoil exploration. At the gold ore deposit, the results of the geological sampling data were processed by the method of constructing the CCG in the form of a histogram showing the frequency of gold extraction and the average amount of its content. Significant peaks of the metal content in the ore, exceeding the level of the average content in the ore by tens of times, have been revealed. Graphical interpretation of the parameters of mineralization reflects the uneven nature of its variability, which indicates the presence of large, rarely occurs of gold in the ore and the need to conduct studies on a sample of ore of greater mass than for ores with tiny gold. On a sample of 50 kg gold-quartz ore studies were carried out on gravity enrichment. The maximum size found in the gold concentrate was 0.07 mm. In the course of integrated tests in a gravity concentrate, gold particles up to 3 mm in size were found, which predetermined the need to include the operation of gravity before flotation. A new approach to subsoil research is protected by a patent (RU 2620823).The technological problems that arise before the researcher associated with the processing of resistant ores require the exploration and development of new means and ways of thinking. New problematic situations on complex mineral and raw materials objects are practically not amenable to resolution by existing methods. Integration of industrial and information technologies is necessary. At present, computer graphics (CG) is one of the most rapidly developing areas of new information technologies. For example, in scientific research, including in fundamental research, the accent from the illustrative function of CG (the visualization of what is already known) is increasingly shifting towards the use of computer cognitive graphics (CCG) tools (Bashlykov, 2016). The function of the CCG is to obtain a new knowledge with the help of a graphic representation - a cognitive image or at least to promote the intellectual process of the logical acquisition of this knowledge. In this study, cognitive images are used to graphically represent the distribution of valuable components in the bowels of the deposit, characterizing the state of mineral-raw materials."

Jan 1, 2018

By P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration (Figure 1). Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. Modelling of the system indicates that the electrical double layer is compressed with increasing electrolyte concentration, resulting in an increase in flotation recovery due to a diminishing of the (electrical double layer) repulsion between the bubble and the coal particles. Moreover, for electrolyte concentrations above about 0.1 M the electrical double layer is completely depressed and would have little further influence, if any, on the flotation process. Therefore, the electrical double layer interaction is not the principal determining factor for the flotation of coal in electrolyte solutions.

Jan 1, 2003

By Lutz Rolf, Halit Z. Kuyumcu, Salas Cazón. Milton A.

Aim of experimental investigations was the mathematical description of the abrasion process running with a single particle stress. This is on the one hand the basis for the physical interpretation of the process, on the other hand the base for the simulation of abrasion processes carried out in technical scale. With this investigation for the first time the influence of the particle shape changing with increasing abrasion progress was quantitatively described. This influence affects itself particularly strongly on break-fresh particles up to an abrasion degree of approximately 10 to 20%. This is for the description of technical processes the most interesting area.

Jan 1, 2003

By S. Makni

Flotation is a complex process in which many mechanisms come into interaction. In this paper, an approach to model these mechanisms in order to predict size-by-size flotation performances is presented. The estimation of the collection efficiency of particles takes into account the serial sub-processes of particle-bubble collision, attachment and detachment. The model was applied to an industrial plant and yielded satisfactory results whereby the actual flotation performances could be correctly predicted. Furthermore, the flotation model allowed investigating the possibility of improving flotation performances by a split flotation feed in comparison to the actual single-stage process.

Sep 1, 2012

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even where possible, equilibrium data with a suitable Henry.s law constant are seldom available.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, KGa values can be calculated for the pilot plant and then scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance."

Jan 1, 2003

By Vladimir Vigdergauz, Elena Belogub, Dmitriy Makarov

The influence of supergene oxidation on physicochemical and technological properties of polysulfide ores was studied. Modeling and analysis of oxidation pyrite copper-zinc ore samples from the Valentorskoye deposit show that sulfide floatability is decreased by the longer-term oxidation. The treatment of oxidized samples by sulfuric acid in oxidative conditions and its impact on the elemental sulfur composition on the surface of sulfides was discussed. It is shown that an enhancement of the floatability of sulfides of oxidized polysulfide ores after leaching by sulfuric acid could be perspective for the developing of combining floatation-hydrometallurgical technology of the nonferrous metals recovery.

Jan 1, 2014

By M. H. Moys, M. M. Bwalya

"INTRODUCTIONThe grinding rate prediction scheme makes use of the energy spectra output from the DEM simulations and the statistical quantification of material strength, which can be done using the drop-weight tester or some other similar equipment. The prediction scheme is evaluated using milling experiments performed under well-defined conditions.MATERIAL STRENGTH QUANTIFICATIONUsing the drop weight test machine, particles of a wide size range were broken singly using different energy inputs. A characteristic equation key to milling rate prediction that relates the probability of fracture with energy input and number of impact attempts was obtained and is stated as follows:"

Jan 1, 2003

By Y. Q. He

The methodology of active pulsing air separation is a new method for dry material classification. Especially, it is suitable to electronic scraps disposal and re-utilization. By studying the difference of drag coefficients of the particles moving through areas of varying Reynolds numbers, and considering the extra-mass forces acting on the particles in the active pulsing air field, models of the dynamic motion which particles follow were developed. A computer simulation was prepared that showed the traces of particles with different densities and/or diameters, but similar aerodynamic characteristics, as they moved through the turbulent flow, to modify and define the parameters of the models. The simulation was found to predict the observed results with artificial tracing spheres being separated by the laboratory equipment. The separation performance, as being affected by the particles, nature, the air velocity, the pulsing frequency and the air pattern, is discussed. In general, lower density particles are more responsive to variations in airflow velocity. In addition, an industrial scale active pulsing air separator was designed, and it provides a new and efficient method for resource re-utilization in China.

Jan 1, 2014

By Wolfgang Öfner

Many technical processes also yield dusty residues which usually contain appreciable amounts of valuable matter. Often they also accumulate substances detrimental to the process. Dumping them entirely in landfills wastes raw material and causes high disposal costs, but recycling them without prior treatment is often not feasible. Physical separation processes are preferable because of their rather low energy demand. In order to develop such treatment systematically, the residues must be characterized properly. The technique for such a characterization is taken from mineral processing: perfect fractionation according to continuous properties of the particles supplemented with chemical analysis are used for plotting the Henry-Reinhardt chart. This represents the benchmark for assessing actual separation processes and tests. Their results are compared in terms of ?selectivity? and plotted in the kappa chart. In this paper, Henry-Reinhardt chart and kappa chart are applied to several different types of residues from iron and steel production and show their potential for being upgraded before reutilization in the production process. This approach is suitable for virtually all dusty residues from other industrial processes as well. Keywords: residue, dust,iron and steel, process development, Henry-Reinhardt chart, kappa chart

Sep 1, 2012

By Thomas Mütze, Petya Atanasova, Kai Bachmann, Urs A. Peuker, Thomas Leißner

"A method is presented for the evaluation of mineral processing by liberation and upgrading. The method bases on the plot of recovery of valuables versus the recovery of gangue (Fuerstenau upgrading curve). The locking curve of a feed material was plotted together with the upgrading curve in a Fuerstenau diagram. The assessment of liberation and upgrading is done by a comparison of surfaces formed by the curves and some characteristic lines of the diagram. This plot allows the calculation of two new quantitative measures for liberation and upgrading. Both parameters can be combined to a third parameter describing the quality of the whole technical setup for mineral processing by subtracting the upgrading parameter from the liberation parameter. The third parameter shows a positive value in cases of upgrading determined processes, a negative value in cases of liberation affected processes and about zero for processes affected equally by liberation and upgrading. Thus it is easily possible to distinguish between poor results in the mineral processing caused by insufficient liberation or poor results caused by insufficient upgrading. Preliminary results from two case studies, performed on two different ore types, are very promising illustrating the practical use of such an approach."

Jan 1, 2014

By B. Rath

An effective process plan is an important part of maintaining consistent recoveries in mineral processing operations. Traditionally, Mineralogical studies are completed using chemical and metallurgical methods to monitor recovery and elemental distribution. The development of mineralogy and more efficient processes in mineral analysis techniques means that mineralogy is now more accessible as an efficient and comprehensive study tool. As operating costs increase and feed grades decrease it is important to maintain tight control of process and ensured maximum recovery is maintained at all times. Just a few days of losses in recovery caused by changes in ore type or processing conditions can have a large effect on total metal recovery and profit. Mineralogical audits can be used to minimize these losses by monitoring the fundamental behavior of feed ore on a regular basis. Smart use of mineralogical studies can develop mineralogical and ore type benchmarks in a detailed, which can be used in process control and monitoring. Geological ore types can be used to identify key mineralogical parameters that may be used in routine and cost effective analysis. Mineralogical systems ideally suited to this because of the depth of information on everything from modal mineralogy to locking/liberation characteristics and mineral associations. Mineralogical studies can equally be applied to specific unit operations within the process, which can allow more detailed information to be gathered on areas of the process that have been identified as critical. This will be especially effective for flotation or oxidation processes where process parameters can be very sensitive to small changes in mineralogy. This paper deals with the Ore Morphology, Ore Mineralogy, Gangue mineralogy, Photo micrographs under reflected, transmitted light and XRD studies Ore, Mineral studies of Sub grade Iron ore of Bacheli Complex, Bailadila Sector, India. Keywords: mineralogy, liberation, liberation studies, ore mineral, gangue mineral, morphology, jasper, ferruginous clay

Sep 1, 2012

By H. Gallardo, J. Yianatos

Flotation is a separation process in which mineral recovery depends on the particle surface properties. The selective collection of particles by air bubbles requires hydrophobic mineral surfaces. Hydrophobicity can be selectively induced on a valuable mineral surface by means of reagents. For this purpose, it is required that mineral grains in the ore become physically liberated or exposed in the particle surface after grinding. The grinding process generates three types of particles according their exposed surface in the floatable mineral: locked particles (0-10%), associated particles (10-90%) and liberated particles (90-100%). Locked particles have low floatability, and they typically show low recovery (<20%), while liberated particles have a high floatability and can be easily recovered (98-100%) at different particle sizes (10-150 µm). The main challenge in the flotation process is the recovery of associated particles. These particles typically have recoveries of 20-80%, but strongly depend on the particle size, particle surface liberation and collector dosage. Recent studies on particle floatability by size-liberation have significantly contributed to improving the characterization of flotation processes. In this work, a study of flotation recovery of associated particles of 10-90% liberation is presented for particle sizes (10-150 µm) and collector dosages (5-40 g/ton). In this work historical data on galena recovery based on particle cross-section composition of galena was used, assuming they represent an acceptable estimate of particle surface composition, as shown by some previous researchers. The results showed that galena recovery can be well represented by a model consisting of the interaction of a linear function and a Gamma distribution function to account for the liberation and the particle size effects. Consequently, an alternative approach for modelling the recovery of associated mineral (10-90% liberation), with a reduced number of parameters, was developed and validated.

Jan 1, 2018

By Peter Ay, Harry Pempel, Satya Narra, Mike Müller, Jens Markowski

"Within the next few years major changes in mobility are expected. Increasing numbers of electric powered cars, electrobikes and E-Scooters define the transport sector. Recently lithium based traction batteries as storage medium have led into matrurity of series production combining high electrical efficiencies with low weights and compact dimensions. Due to the relatively young development with lithium batteries utilization, only few investigation were conducted regarding their recycling. Conventional battery recycling processes can not be applied due to differences in design and chemistry. So an automated disassembly and processing procedure for lithium traction batteries has been developed in the R/D-project ""Li-WERT"". Instead of complete smelting of the batteries without pretreatment, an automated disassembly and specific treatment of the material streams was realised, adjusted to the needs of the subsequent recovery technologies. A higher quality, with reduced expenses for the separation of fine-grained or fused material mixes, can be obtained for the individual components. The automated disassembly using an industrial robot significantly reduces dangers for the operating crew. The selective disassembly and beneficiation allows full recovery of the fractions. The batteries will be disassembled to cell level by the industrial robot. Anodes, cathodes, and separation layers are isolated and processed. The technology is designed, that no waste is generated for disposal. The pelletised cathode coating and the other separated metals (stainless steel, copper, aluminum) can be used in respective metallurgical plants. Circuit boards and plug contacts are also coveted secondary raw materials for reuse. The process is modular and offers high flexibility, e. g. for new battery types/ sizes by quick adjustment of the robot and tool change. Adaptation to other cathode materials (e. g. Li[FePO]) is possible. After finishing the R/D-project, a pilot plant for demontage was realised in 2013."

Jan 1, 2014

By H. Z. Kuyumcu

Coking of coal blends using high volatile coals with poor coking abilities to produce a high quality coke for blast furnace application can be achieved by compacting the coal blend prior to the carbonization process. Here densification up to a relative material density of 80 %, i.e. a compact density around 1100 kg/m3, has proven to be advantageous. Coal is compacted by stamping, if the so-called stamp charging process applied. Compacting of the coal by pressing is practised in case of the cokemaking with so-called heat-recovery ovens. Stamped and pressed coal cakes require over the cake volume uniform high density and mechanical stability. Besides the aspects of the coal selection, the efficiency of the process is mainly determined by the operating parameters compacting time and compacting energy for coal cake making. At the Department for Mechanical Process Engineering & Solids Processing of the Technical University Berlin the two sub-processes of densification and strengthening during stamping and during pressing are theoretically and experimentally investigated using specially developed lab-scale compacting test units and a strength test device. Describing cake density in terms of coal properties for a given coal and measured compacting energy input then leads to a compacting equation with the so-called Stampability as the integral model parameter for the stamping process. For the pressing process the cake density can be calculated with the measured compacting pressure and the Compressibility factor, respectively. Investigations were carried out to provide evidence of a significant influence of coal type, coal surface moisture, coal granulometric and mechanical properties on the densification process. The overall objective of the work is to establish a comprehensive mathematical model on the compacting behavior of large coal bulk quantities and the optimization of the compacting processes by stamping and by pressing. Keywords: coal compacting, agglomeration, stamping, pressing, cokemaking

Sep 1, 2012

By Genrich A. Denisov

Principles of ecologically friendly geo-technologies construction are formulated on the basis of the works of the leading scientists in the field of rational processing of mineral resources of the Russian Academy of Sciences. One of these concepts is a new direction in rotational disintegration of mineral and technogenic raw material with the purpose of effective subsequent enrichment. A large amount of practical experience has been accumulated in the industry on selective destruction by application of vibrational method on initial material with consideration of its physical-mechanical properties and mineral structure. This method is successfully realised in a conic inertial pulverisation devices constructed by Mekhanobr Institute (St. Petersburg). A new construction of conical-inertial pulverisation with a modification of disintegration force has been developed recently at Mekhanobr Institute. It allows, in some cases, to increase selectivity of subdivision and to avoid over-disintegration. Advantages of “wet” subdivision methods in conic inertial disintegration devices are proved. The efficiency of such subdivision can be increased due to rational use of the phenomenon of a dislocation-dynamic diffusion. Its advantage is proved by the effect on disintegrated material by frequency-modulated variable electrical fields of low power. It was shown in industrial conditions, that the productivity of the spherical mill can be increased by 10 %, and that it also prevents ecologically harmful surface active substances (SAS) in milling zone and it reduces the dust content in the air. The techniques of tentative estimation of efficiency of various proceedings technogenic materials and their classification are created. The scientific fundaments of rational, ecologically friendly technology of processing and regeneration of various kinds of technogenic raw material are developed. A number of effective technologies on processing of wastes is developed and inculcated in concentration factories and metallurgical factories.

Jan 1, 2003

By David I. Verrelli, Boris Albijanic

"Froth flotation is an exceedingly complex physicochemical process. The convenience of distilling much of the complexity of the bubble-particle interactions into a single parameter has led to the continuing popularity of the classical ‘induction time’ to quantify the threshold for bubble-particle attachment to occur. Despite this popularity and the simplicity of the concept, there is no single universal method of evaluating the induction period. In this paper, we begin with a critical review of the available techniques for estimating the induction period. These are: back-calculation from experimental (micro) flotation tests; pushing a particle toward a stationary bubble (or vice versa) using an atomic force microscope (AFM); pushing a bubble toward a stationary bed of particles in the ‘Induction Timer’; pushing a bubble toward a stationary solid surface using the ‘integrated thin film drainage apparatus’ (ITFDA); and dropping particles onto a submerged stationary bubble using the ‘Milli-Timer’ device. Each one of these methods has advantages and disadvantages, and the best choice depends on the application. In the experimental section, we present quantitative comparison of the induction periods estimated using two different techniques, namely the Induction Timer and the Milli-Timer. The same particles were tested in each device, under the same conditions. It was found that by tuning the operation of the particle pick-up device, similar estimates of induction period could be obtained to the estimates made by direct observation with the Milli-Timer. In the former device a bubble is driven toward a particle bed at a controlled rate, whereas in the latter a particle’s motion is governed by the hydrodynamics. The potential to match these presents an intriguing prospect for better understanding the bubble-particle interaction, and the possibility to ‘calibrate’ the simpler Induction Timer against direct observations."

Jan 1, 2014

By Alexander E. Sobolev

The kinetics of oxidative dissolution of lead sulfide in solutions of nitric acid and sodium hypochlorite was studied using the rotating disk method and the factor experiment design. The dependences of the PbS dissolution rate on concentration of oxidant (HNO3 or NaOCl), temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific dissolution rate at any combination of values of the influencing factors were obtained. As a result of the complex analysis of kinetic parameters, the modes of the each process proceeding were established, their macromechanisms were determined, and the limiting stages of the oxidative dissolution processes were revealed. The dissolution kinetics of lead sulfide in solutions of nitric acid was found to have several regimes. At HNO3 concentrations below 0.5 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled. It is caused by low oxidative activity of HNO3 and considerable diffusional diffuculties at this acid concentration range. At the nitric acid concentrations more than 0.5 mol/L and less than 6.0 mol/L, the process was found to be kinetically controlled. The limiting stage of the interaction is the surface chemical reaction. The observed relatively high order of the dissolution rate with respect to the concentration of HNO3 was explained by the autocatalytic action of the acid reduction products. At nitric acid concentrations exceeding 6 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled, and the dissolution rate sharply decreased that was explained by a decrease in the solubility of reaction products. When lead sulfide is dissolved in sodium hypochlorite solutions, at first time the amount of PbS transferred into solution remains close to zero. Gradually, as time goes, this amount begins to increase sharply. The dissolution rate rises and reaches the maximum value, further remaining constant. At the steady-state regime, the dissolution rate is independent of the duration of interaction and disk rotation frequency. The process was found to be kinetically controlled. The limiting stage is likely to be chemical reaction on the surface of solid lead sulfide. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulfides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of lead-bearing ores and concentrates. Keywords: lead sulfide, nitric acid, sodium hypochlorite, hydrochemical oxidation, dissolution kinetics

Sep 1, 2012

By Kazimierz Trybalski

"Simulation methods have a big potential in the studies and analyses of complex technological processes and schemes. The simulation method used jointly with flow diagrams and related transmittance models allows describing and analysing dynamic characteristics.The paper presents results of simulation analysis of dynamic characteristics of ore dressing system, called closed circuit mill-classifier-mill. Such systems are widely used in ore processing plants. The system was analysed as a typical system with material feedback, to establish its dynamic characteristics.Flow diagram conforming to the technological scheme is presented in a figure. Transmittances shown in the scheme are defined as follows:GMP - transmittance of rod mill,GP, KZ, GW, KZ - transmittances of overflow and underflow streams of spiral classifier, respectively,GMK - transmittance of ball mill,GT - transmittance of underflow stream from classifier to ball mill,GU, MP, GU, MK - fraction transmittance of outflow streams of rod and ball mill, respectively, summed up at classifier input.Taking into account, in base of carried out analysis the transmittance forms of individual system elements. The calculations are based on numeral forms of transmittances of individual blocks, defined through industrial experimentation.Step input function to rod mill was assumed to be a step of mass ore flow rate to the mill. Responses are defined as product densities.This figure demonstrates the way of input signal transmission by consecutive elements of the system and shape of these elements' responses. It can be noticed that step signal undergoes gradual change from the stream of the first order to those of higher and higher orders as a distance from process leading edge increases. Simultaneously, the impulse signal is subject to systematic smoothing and decay. From the technological point of view, the most important is response stream in point 5 (on the above figure) that characterises classifier overflow, which is a final product of this system."

Jan 1, 2003