Search Documents

By James R. Hein

Rodriguez Seamount, located 150 km off the central California coast at the base of the continental slope, was studied using the ROV Tiburon aboard MBARI?s R/V Western Flyer, October 13-16, 2003. Fe-Mn crust and rock samples were collected along the SW flank of the seamount at water depths from 700 to 2100 m; bottom-water dissolved oxygen content (O2) and temperature were determined at each sample site. Fifty-three samples of bulk crusts, crust layers, and surface scrapes (~0.5 mm) were analyzed for 59 elements. Data allow for the correlation of crust compositions with precisely known water depths and seawater O2 measured at the actual site of sample collection. This is the first detailed study of Fe-Mn crust compositions in a region of strong continental-margin upwelling. Compared to open-ocean seamount Fe-Mn crusts, Rodriguez crusts have significantly higher (2-6 fold) mean concentrations of Fe (26.9%), Al (1.65%), Si (13.0%), Cr (82 ppm), Th (64 ppm), and Ag (1.7 ppm); and significantly lower (2-8 fold) mean concentrations of Ca, P, Bi, Co, Cu, Ni, Tl, and especially Te (8.2 times lower). All but one Fe/Mn ratio are >1 compared to <1 ratios for open-ocean crusts. O2 contents (0.35-2.03 ml/L) are nearly perfectly corrected with water depth and elements correlated with one are correlated with the other. The Fe-Mn surface scrapes represent 60-450 ka (mean 150 ka) of growth, whereas the dissolved oxygen contents of seawater represent an instant in time. Assuming that the entire sample set was affected uniformly by oceanographic changes, we suggest that correlation of elements with O2 may reflect oceanographic processes. O2 has a negative correlation with P, V, As, Fe, U, Be, Pb, Cr, Mg, Y, Bi, Te, and REEs (except Ce) and a positive correlation with aluminosilicate-hosted elements (Al, K, Rb, Cs). This later relationship is related solely to water depth, indicating that detritus shed down the seamount slopes accumulates in greater abundances in deeper-water crusts. Si/Al ratios indicate that the detritus includes a large component of biosilica produced by upwelling-mediated high productivity. These observations are supported by positive correlations of aluminosilicate-hosted elements with crust growth rates (range 1.2-13.0 mm/Myr). In contrast, other elements (Sr, Co, Mn, Mg, Te, As, Mo, V, W, U, Ti, Ni, REEs, etc.) are negatively correlated with growth rates. Growth rate has a weak positive correlation with O2. These compositional characteristics indicate that even though low-O2 seawater acts as a reservoir for Mn and associated elements and produces slow growth rates, which would allow for the concentration of elements and surface oxidation processes to occur, the high rate of input of detritus and high bioproductivity ameliorate the strong concentration of most metals. This dilution is significantly enhanced by the doubling of FeOOH in the crusts--the main cause of the generally high growth rates compared to open-ocean crusts. The high growth rates limit the oxidation of Co, Tl, and especially Te on the crust surface, which is reflected by their relatively low concentrations. Within the range of oxygen contents measured, O2 has less of an influence on crust chemistry than does the availability and incorporation of FeOOH and detritus.

Jan 1, 2004

By Grigori Abramov

Borehole Mining (BHM) is a remotely operated underground and underwater method of extracting (mining) mineral resources by high-pressure water jets. It can be carried-out from the land surface, open pit floor, underground mine and floating platform or vessel. The method is currently in use in mining and exploration of such natural resources and industrial materials as: uranium, iron ore, quartz sand, gravel, coal, poly-metallic ores, phosphate, gold, diamonds, rare earths, amber and several more. Yet another application of Borehole mining technology is construction of subsurface collectors, ground walls and storage for compressed or liquefied gases, oil and other products.

By James M. Cairns

Deep Sea Minerals Inc. (DSM) is a high technology marine minerals and biotechnology corporation. The corporation is currently engaged in a worldwide leasing program to acquire exclusive rights in specific Economic Exclusive Zones (EEZ?s) that DSM?s marine geologists have identified as prospective targets for seabed mines of copper, zinc, gold, and silver. In the last two years the corporation has assembled an international team, including some of the world?s leading marine research scientists and engineers, and has created strategic partnerships and alliances with world-class engineering and mining groups. Development of a marine mining venture has key requirements in common with most other mining ventures. These include financing, deposit location, property acquisition, deposit delineation, and permitting, as well as the collection, transportation, processing and marketing of the ore itself. DSM has made progress on all of these fronts, which is outlined in a general way in this presentation. Financing for the venture is clearly the first big hurdle to overcome. Deep seabed mining involves new technologies and significant up-front capital investment. Less than fifteen years ago, such financing would probably have impossible to achieve, given classical business models. However, with the spectacular success of high technology ventures in the areas of electronics, software, and biotechnology, new business models and investment strategies have evolved which put relatively high evaluations on intellectual property and exhibit relatively high confidence in new ways of doing things. DSM is taking full advantage of these changes in venture capital markets in its financial planning.

Jan 1, 2000

By Karsten Hagenah, Tor Jensen, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks

"The methods and technologies to be used for environmental monitoring of seabed mining activities are a key issue. Due to the large water depths, there are special challenges with respect to the monitoring equipment that is suitable. DNV GL has built up substantial experience of environmental monitoring from oil & gas projects in deep waters in the Norwegian Sea.Monitoring equipment and experiences from the oil & gas sector can to a large extent be applied to seabed mining.BackgroundThe International Seabed Authority is currently developing an environmental management strategy for the Area (ISA, 2017) as a part of the work on the regulations for exploitation for mineral resources in the Area.The draft environment strategy contains provisions related to monitoring and reporting of the activities. An Annex (Annex III) of the draft document describes the format and content of the environmental management and monitoring plan.The monitoring plan should contain, inter alia: ?Technology to be deployed.?Monitoring frequency of respective elements/components of the Marine Environment.?Monitoring procedures required to implement the Monitoring programme.?Details of the environmental monitoring stations across the Environmental Impact Area.?Monitoring specifics e.g. water quality; sedimentation rates; sound; plume extent; etc., as well as relevant Environmental Targets.?Monitoring of Mining Discharges.?Processes for Monitoring reviews and Environmental audits."

Jan 1, 2017

By Gary J. Massoth

Wherever hydrothermal fluids vent from the seafloor they will buoyantly rise (up to 100?s of meters) while mixing with seawater before attaining density equilibrium and dispersing laterally as neutrally buoyant plumes commonly 50 to several 100?s of meters in thickness and with order-of-magnitude or greater breadth. Although these plumes are typically >10,000-fold dilutions of vent fluids they can be reliably detected using sophisticated physical sensing and chemical techniques. Hence, hydrothermal plumes are spatially large targets compared to the actual sites of seafloor fluid discharge and resulting mineralization. For this reason plume prospecting techniques evolved over the past 20+ years have been widely used to systematically explore over 10% of the 60,000-km-long system of mid-ocean ridge (MOR) spreading centers for hydrothermal activity. While plume detection and gradient mapping can be used to home in on venting sites, plume chemical signatures provide additional insight regarding the nature of the fluids being discharged on the seafloor. We have applied the systematic plume prospecting techniques developed on MORs to the volcanic frontal arc setting as part of the NZAPLUME (New Zealand American PLUme Mapping Expedition) surveys. NZAPLUME I in March 1999 marked the first systematic reconnaissance of any intra-oceanic arc for submarine hydrothermal activity. Seven of thirteen previously mapped volcanoes that comprise a 260-km-long section of the southern Kermadec arc northeast of New Zealand were confirmed to be hydrothermally active. On average, one hydrothermally active volcano was found along each 35 km of arc front, a rate comparable to slow- and intermediate-rate spreading MORs. During NZAPLUME II in May 2002, thirteen previously unknown volcanoes and 8 satellite cones were first swath mapped for bathymetric detail and then surveyed using plume prospecting techniques. Three active venting sites were discovered along this 580 km-long arc section, bringing the total to 10, or 39% of 26 volcanoes surveyed overall, still an appreciable frequency rate for venting sites compared to MORs. While only chemical results for NZAPLUME I are available, the arc plumes characterized so far are chemically diverse and rich compared to MOR plumes. This diversity and enrichment was most evident as ultra-high concentrations of CO2, sulfur gases (St = SO2 + H2S), and Fe within plumes over several volcanoes. We suggest the fluids discharging from the seafloor at these sites are volcanic fluids, i.e., hybrid fluids comprised of MOR-like hydrothermal fluids evolved from seawater-rock reaction and fluids exsolved from magma as acid volatiles and liquid brines.

Jan 1, 2002

By Samantha Smith

Nautilus Minerals (Nautilus) is following the lead of the petroleum industry as it strives to tap vast offshore resources. Planning is well underway for the Solwara 1 Project in the Bismarck Sea, Papua New Guinea (PNG) to recover high-grade seafloor massive sulphide deposits in 1600 m water depth. The deposit contains an average copper grade >10 times higher than a typical land-based porphyry copper mine. The high grades combined with a relatively small amount of overburden ensure the Solwara 1 Project will have a significantly smaller physical footprint than its land-based counterparts. Offshore minerals production also has the advantage of minimal social disturbance. Nautilus is dedicated to setting a high environmental and social responsibility standard. Nautilus recognises the importance of transparent and inclusive stakeholder engagement and has taken a proactive approach to involve as many key stakeholders as possible. One of the first steps in the permitting process in PNG is the preparation of the Environmental Inception Report, which describes the project, its envisaged impacts and the proposed studies for the Environmental Impact Assessment (EIA). Local (PNG-based) and international environmental scientists, anthropologists, NGOs and other experts were involved in the definition of studies conducted for the Solwara 1 EIA and a team of world-leading experts was involved with carrying out the studies, culminating in the preparation of the Environmental Impact Statement (EIS). To ensure transparency, collaborating researchers are free to publish their findings. Following its submission, the EIS was made available for public review and public hearings were held at several locations. The EIS has also undergone a rigorous independent review by PNG government-engaged consultants. Outside the permitting process, Nautilus works alongside government officials to carry out ongoing community consultations. Information dissemination and feedback acquisition has also occurred through the Nautilus website and attendance at a number of international conferences, workshops, and meetings. This paper will outline the leading edge approach Nautilus has taken in completing the environmental impact statement for the world?s first deep seafloor copper-gold mine. In addition, this paper will review the permitting process and the government and stakeholder engagement undertaken as part of Nautilus? desire to ?do it right? in this exciting new industry.

Jan 1, 2010

By Sup Hong

A pilot mining robot, named MineRo-II, has been developed by KIOST during 2011-2012. The pilot scale was defined as 1/5 of the commercial mining capacity, 1.5 million dry-tons of nodules per year. The development purpose of MineRo-II is to use for the pilot mining test planned in 2015. MineRo-II was designed to be self-propelled by electric-hydraulic power and remotely operated in real-time from aboard. The main operational functions are crawling on seafloor, pick-up and crushing of nodules, discharging nodules out to buffer. Prior to MineRo-II, a test miner (MineRo-I) was developed in scale of 1/20th in 2007, and performed two times sea trials in 2009 and 2010. The results of performance tests were evaluated and utilized for the concept of MineRo-II. The design concept aimed at the expandability of the mining capacity based on modularity of configuration, maintenance simplicity and multiplicity of backup solution. The pilot-scale mining capacity is achieved by four pick-up modules of each 1m wide, which are moving forward with robot vehicle and sweep the nodules entering below the pick-up heads. Principally, by adding the pickup modules in lateral dimension the mining capacity may increase linearly. MineRo-II was designed and constructed in unit-module wise. The robot consists of two unit-modules having an identical mechanical and hydraulic configuration. Each unitmodule has two tracks, two pick-up devices with attitude control devices, two crushers, one discharge pump, and one hydraulic system. Two unit-modules are connected by one loading frame and integrated by electric-electronic system. Two thrusters for control of the

Sep 14, 2011

By Matthew Kowalczyk, Steve Bloomer, Peter Kowalczyk

"Mineral deposits found near seafloor hydrothermal venting are of great economic interest. Valuable metals such as gold, copper, zinc, and other polymetallic sulfides are found in appreciable grades in seafloor massive sulfide (SMS) deposits associated with these vents. For mapping these deposits, electromagnetic prospecting is one geophysical method that is very useful because copper/gold rich deposits are highly conductive.Ocean Floor Geophysics (OFG) in 2008 developed the first EM system to successfully map the limits of conductive mineralization in a survey at the Solwara 1 deposit (Kowalczyk, 2008). Since then, towed coincident loop time domain systems have been developed by Waseda University (Nakayama and Saito, 2016) and have successfully detected known mineralization buried at 30m depth. Using a deep tow controlled source electromagnetic (CSEM) array, very clear anomalies have been measured (Murton, 2017) over known mineralization at the TAG field on the mid-Atlantic ridge.In 2014 and 2015, OFG partnered with Fukada Salvage and Marine Co. Ltd. and the Scripps Institution of Oceanography to map methane hydrate deposits off the coast of Japan using a towed controlled source electromagnetic (CSEM) system developed by Scripps. These hydrate deposits are resistive targets, and the Scripps system successfully mapped subsurface electrical resistivity distributions to depths of several 100 metres below the seafloor. OFG is attempting to extend the Scripps CSEM technology to map subsurface conductive SMS deposits to a similar range of depths below the seafloor."

Jan 1, 2017

By Masaomi Kurihara, Seiya Kawano, Norihiro Yamaji, Satoshi Shiokawa, Nobuyuki Okamoto, Hironobu Sakurai

Seafloor polymetallic sulphides are distributed in the EEZ of Japan, including substantial deposits in the Okinawa Trough and Izu-Bonin back-arc basin. In this new frontier, the successful development of these resources in Japan is expected to bring about a new domestic supply of mineral resources. The initial stages of this development are authorized by the Basic Plan on Ocean Policy, approved by the Japanese Cabinet on April 26, 2013, and the Plan for the Development of Marine Energy and Mineral Resources, formulated by the Ministry of Economy, Trade and Industry (METI) on December 24, 2013. In 2008, the Japan Oil, Gas and Metals National Corporation (JOGMEC), commissioned by METI, began a survey and technological development programme for the development of the seafloor polymetallc sulphides (PMS) based on these Plans. The examination of four different fields: the evaluation of the amount of the resource, environmental assessment, mining technology, and processing & smelting technology, are concurrently promoted, aiming for commercialization as soon as possible. Based on the results of research for properties of geomorphology and marine environments of the target test sites in the Okinawa trough, which have been ongoing for several years, the preparation of the pilot lifting test included an in-situ excavation and crushing test conducted using test excavating and crushing systems.

Jan 1, 2018

By Masaomi Kurihara, Seiya Kawano, Norihiro Yamajim, Satoshi Shiokawa, Nobuyuki Okamoto, Hironobu Sakurai

Seafloor polymetallic sulphides are distributed in the EEZ of Japan, including substantial deposits in the Okinawa Trough and Izu-Bonin back-arc basin. In this new frontier, the successful development of these resources in Japan is expected to bring about a new domestic supply of mineral resources. The initial stages of this development are authorized by the Basic Plan on Ocean Policy, approved by the Japanese Cabinet on April 26, 2013, and the Plan for the Development of Marine Energy and Mineral Resources, formulated by the Ministry of Economy, Trade and Industry (METI) on December 24, 2013. In 2008, the Japan Oil, Gas and Metals National Corporation (JOGMEC), commissioned by METI, began a survey and technological development programme for the development of the seafloor polymetallc sulphides (PMS) based on these Plans. The examination of four different fields: the evaluation of the amount of the resource, environmental assessment, mining technology, and processing & smelting technology, are concurrently promoted, aiming for commercialization as soon as possible. Based on the results of research for properties of geomorphology and marine environments of the target test sites in the Okinawa trough, which have been ongoing for several years, the preparation of the pilot lifting test included an in-situ excavation and crushing test conducted using test excavating and crushing systems.

Jan 1, 2018

By Jeremy Spearman, Alan Cooper, Mark Lee, Jon Taylor, Michael Turnbull, Neil Crossouard, Bramley Murton

"SUMMARYSeamounts are underwater mountains caused by volcanic activity. They are of great oceanographic interest because of their local and basin-scale influence over ocean systems, their often unique ecosystems, and because they are associated with the formation of ferromanganese (Fe-Mn) crusts. These crusts are of particular interest to scientists because they are rich in some of the rare elements increasingly required for development of renewable technologies. When the possibility of mining such seamounts is considered, an inter-disciplinary study of seamount hydrodynamics, crust formation and ecosystem sensitivity is required. MarineE-tech is one such multi-disciplined project that has been commissioned to address these different aspects in order to improve understanding of the viability and desirability of mining Fe-Mn crusts. This paper describes a key part of this study, namely the development of a model, informed by hydrographic observations, of the currents around one such seamount and the in situ validation of a sediment disturbance plume model as a pre-cursor to assessment of the potential effects of mining activity.INTRODUCTIONFerromanganese crusts are thought to form by precipitation of iron and manganese oxides from oxygen depleted mid-water known as the oxygen minimum zone (OMZ). Oxidation rich waters, typically at depths of about 800-2200 m (Hein et al, 2000). This range of depths coincides with the flanks and summits of many seamounts. The ferromanganese crusts found on seamounts have been found to have high concentrations of rare elements, like Tellurium, that are considered critical to low-carbon energy production. Seamounts are complex environments: in terms of the local hydrodynamics that tend to trap water over the seamount due to the Taylor Cap effect (e.g. Chapman and Haidvogel, 1992) and which can enhance the productivity of seamount waters through upwelling (Lavelle and Mohn, 2010), in terms of the microbiological activity that leads to the precipitation of the Fe-Mn crusts, and also in terms of the often unique ecosystems that are the product of the “island” nature of seamounts and the upwelling of nutrients. The understanding of this complexity is a necessary journey towards the realization of viable, yet environmentally responsible, mining schemes. The formation of crusts will be influenced by the local (and larger-scale) hydrodynamics. The exploration of promising crust sites could be made much more efficient by understanding where the most prospective deposits are likely to occur. Knowing how to remove these crusts without impacting significantly on the local environment will be a pre-requisite for such mining to be acceptable to the public and funders alike."

Jan 1, 2017

By Jiahua Pan, Yanxiong Mei, Shuqin Liu, Rongfu Pei

Growth characteristics of Co-rich crusts from the Western Pacific have been approached. The thick crust shows 3 structural layers: compact upper layer, porous middle layer, and compact lower layer. The middle and lower layers have obviously different microscopic structure, color, and luster. Preliminary study of Calcareous nanofossils in one crust shows that the crust began to grow since Paleogene. The porous middle layer was formed from late Miocene to late Pliocene (Ca. 0.5 ~ 11.9Ma) and the compact lower layer was formed from late Paleocene to late Oligocene (Ca. 56.3 ~ 23.2Ma). The sedimentary hiatus of a 14.26Ma was observed between the middle and lower layers. The boundary between them to be Oligocene/Miocene (O/M) shows an important message on growth age.

By Irina Dobretsova, Anna Sukhanova, Anatoly Kondratenko, Svetlana Babaeva, Sergey Andreev

"With the acceptance of an application and a signed contract for prospecting deep-sea sulfides (2012) between the Russian Federation and the ISA, at present it is particularly important to assess the quality of oceanic sulfide minerals and to reliably estimate their resources.Some procedures of geochemical classification (chemical analyses, mineral composition of SMS) and calculations (density of ore, density of the mineral part of the ore, porosity and moisture contents) were used for estimation of mineral resources potential.The key characteristics for estimating the predicted resources of hydrothermal ore fields are the metal contents and the density of wet and dry sulfide ores. However, in the future it is impossible to provide an estimate of the predicted resources without taking into account the following important factors:- the quantitative ratio of main sulfide minerals;- proportion of non-metallic components (opal, quartz, talc);- the replacement of primary minerals by copper sulfides;- texture-structural features of sulfide ores.The offered mineral classification of the SMS is based on the prevalence of minerals in the ores and partly on their composition. The main ore-forming minerals of SMS are pyrite, chalcopyrite and sphalerite. Sulfide mineralization is accompanied by the presence of nonmetallic minerals, where quartz and opal prevail, and where we also meet aragonite, talcochlorite and anhydrite."

Jan 1, 2017

By Peter A. Rona

The Mid-Atlantic Ridge in the central North Atlantic and the Gorda Ridge within the U.S. Exclusive Economic Zone off northern California and southern Oregon are yielding new discoveries of seafloor hydrothermal mineralization. The TAG hydrothermal field in the rift valley of the Mid-Atlantic Ridge near 26 degree N, 45 degree W has been a site of international collaborative research since the discovery there of extensive manganese deposits associated with low temperature hydrothermal activity in 1973 as part of the TAG (Trans-Atlantic Geotraverse Project). The first high-temperature hydrothermal activity, massive sulfide deposits and vent biota discovered in the Atlantic were found at the TAG hydrothermal field in 1985. Collaborative dive series with DSV ALVIN in 1990 and in 1991 with the two Russian MIR submersibles in the TAG field have found and sampled large inactive sulfide mounds in addition to the previously known active sulfide mound. The active sulfide mound on the floor of the rift valley is about 250 m in diameter and 40 m high with a concentric zonation of mineral types and flow regimes decreasing in temperature from 365 degree C black smokers at the center to white smokers and diffuse flow toward the margins. The recent dive series in coordination deep-towed instrument surveys have delineated a zone extending about 5 km along the lower east wall of the rift valley of inactive sulfide mounds up to a kilometer in diameter. MIR Mound in this zone consists of a central sulfide zone about 400 m in diameter and 50 m high surrounded by a halo of low-temperature deposits to 200 m wide. Inactive sulfide chimneys contain the first primary, free gold grains found at a hydrothermal site on a mid-ocean ridge (P.A. Rona, Y.A. Bogdanov, E.G. Gurvich, N.A. Rimski-Korsakov, A.M. Sagalevitch and M. D. Hannington, 199 1 EOS, Transactions, American Geophysical Union, 72:470-471 and Journal of Geophysical Research, submitted).

Jan 1, 1992

By V. V. Ivanov, A. I. Khanchuk, E. V. Mikhailik, M. G. Blokhin, P. E. Mikhailik

At present, marine ferromanganese crusts of seamounts are of great interest as a source of high-tech metals. The metals most enriched in these deposits are essential for a wide variety of green-tech, emerging-tech, and energy applications (Hein et al., 2013). There is a grate number data on the content of major and minor metals (thousands analyses). However, information on the content of such elements as platinum, gold and silver in the world literature is limited. The concentrations (N – number of analyses) of platinum, gold and silver in the Pacific are 418 ppb (N = 105), 35 ppb (N = 72), 1.02 ppm (N = 26), respectively, and in the North Pacific Prime Zone - 477 ppb (N = 66), 55 ppb (N = 13), 0.1 ppm (N = 4); in the Atlantic Ocean is 567 ppb (N = 2), 6 ppb (N = 2), 0.20 ppm (N = 18), in the Indian Ocean, 211 ppb (N = 6), 21 ppb (N = 2), 0.37 ppm (N = 9) respectively; (Hein et al., 2013). The northern part of the Pacific is poorly studied in this question. The samples of ferromanganese deposits (FMD) was recovered from the Govorov Guyot (Magellan seamounts), MZh-33 Guyot (Marshall Islands), as well as the Detroit Guyot (Imperor Ridge) and Yomei Guyot (Fe-Mn placer Holes 431 and 431A DSDP, Imperor Ridge).

Jan 1, 2018

By Jonguk Kim

Submarine hydrothermal activity and mineralization related to island arc volcanism along the Tonga arc were explored during two research cruises in October 2009 (KODOS 09H) and February 2010 (KODOS 10H), respectively. In KODOS 09H cruise, geophysical survey, including multi-beam bathymetry, marine seismic and magnetic investigations, was performed on 10 volcanoes to find out possible structural discontinuity that can act as fluid pathway for formation of hydrothermal deposits at submarine caldera system. The result provided acoustic and seismic image maps and magnetic anomaly maps of targeted volcanoes. Then, detailed seafloor observation and sampling as well as deep tow side scan sonar survey were performed in KODOS 10H cruise on 5 volcanoes which are selected as targeted areas from the previous cruise. Among 5 targeted volcanoes, TA26 shows most extensive hydrothermal activity. Hydrothermal vents and alteration zone were observed on western caldera and summit of eastern cone of the TA26. Although only weak hydrothermal alteration was observed on eastern cone, mineralized fragments of chimney and mound were sampled from western wall of central caldera on TA25 volcano. On TA12 volcano, strong hydrothermal plume and alteration zone was detected during video tows operated between SW scoria cone and small ridge. However, only small amount of hydrothermal altered rocks were collected from TA12. Although hydrothermal activity and mineralization might be formed, supported by plume detection and result of geophysical survey, only weak alteration zones were observed on other two volcanoes (TA19 and TA22). The exploration area generally show shallow depth up to several tens of meters on summit where subsurface boiling of hydrothermal fluid might occur due to low hydraulic pressure, which can affect on styles of hydrothermal venting and mineralization process observed on Tonga submarine arc volcanoes.

Jan 1, 2010

By Peter Halbach

The two HYFIFLUX cruises of the German RV SONNE (SO 99/1995 and SO 134/1998) were organized in the framework of a co-operation between several German universities and two European marine research partners. It is a multidisciplinary program for the study of hydrothermalism with its associated geological, mineralogical, and biological processes in the North Fiji Basin (NFB) in the SW-Pacific. The main achievements of the HYFIFLUX cruises were detailed multibeam Hydrosweep mapping in order to identify the detailed tectonic setting, water sampling at hydrothermally active vents, mineral sampling at inactive sites with sulfide, sulfate, and silica mineralizations, and sampling of basaltic rocks, (Halbach et al. 1999). Oceanic accretion in the NFB is characterized by a double spreading system (Auzende et al. 1994),with one spreading axis located in the median part of the basin (Central Fiji Ridge, CFR) and the second one located immediately west of the Fiji platform (West Fiji Ridge). Most of our investigations were done in the northern part of the N 15° segment of the CFR, which corresponds to area A of our program, area D is located farther south in the NFB and corresponds to the N-S segment of the CFR (Fig. 1). During previous works under the French-Japanese STARMER project, the active ?White Lady? mound and the extinct Père Lachaiseí site were sampled; these samples were studied by Bendel et al. 1993. Here an inactive hydrothermal field was studied, where there were many sediment-covered chimneys in various stages of disintegration, (Bendel et al. 1993). However, the area immediately southwest of the nodal circular basin, which is the triple point junction of the medium-spreading Central Fiji Ridge (about 6 cm/yr spreading rate

Jan 1, 2000

By Stephan K. Schwank

In mid 1993, Bauer Spezialtiefbau GmbH, based in Germany got the order to develop a sampling tool capable of penetrating all different types of seabed sediments including cobbles and boulders and into bedrock. BHP and their partners Benguela Concessions Ltd., had been convinced by the Bauer Trench Cutter Technology and a large scale test in Germany that this system will be the right one to fulfill their expectations for sampling the diamond area off the coast of Namibia. The technique of the tool is based on Bauer&apos;s standard cutter technology, which is widely used for the installation of cut-off and diaphragm walls all around the world. The two counterrotating cutter wheels with 12.1 tom torque each cut an area of 3 x 1.2 m (up to 3 x 3 m are possible). The material mixed with seawater was then pumped to the separation plant on board the vessel Geomaster with a capacity of approximately 700 m3/h. Cutter wheels and mud pump were mounted on a special cutter frame and connected by wire ropes and hydraulic hoses to the vessel. An outer frame with four telescopic legs supported the cutter vertically on the uneven seabed and allowed a controlled penetration of the tool up to 6 m into the diamond bearing ground. The tool required a total power installed of approximately 800 kW. All hoses, the 6-inch mud hoses as well as the hydraulic hoses, were stored and compensated on drums on board suitable for a water depth of up to 200 m. Launch and recovery of the tool was effected through the moon pool of the vessel and the 25 m high, special designed drill tower. The 65? to sampling tool had been commissioned in early 1994 in Cape Town. After intensive testing the sampling programme of more than 4000 holes could be successfully completed by January 1995.

Jan 1, 1998

By Charles L. Morgan

"In 2012 the International Seabed Authority (ISA) established nine “Areas of Particular Environmental Interest” (APEIs) for consideration as future Marine Protected Areas to help preserve the biodiversity of life on the seabed within the Clarion-Clipperton Zone (CCZ) between Baja California, Mexico, and the Hawaiian Islands. The CCZ is believed to have a high potential for future seabed mining operations. Areas under active exploration contracts in the CCZ, plus the areas currently reserved by the ISA for exploration by developing nations, comprise about 1.9 million km2 of seabed area. The currently designated APEIs consist of more than 1.4 million km2 of seabed. Each APEI includes a central primary conservation area of 200 X 200 km, surrounded by 100-km buffer areas on all sides. The 100-km buffers are intended as a very conservative spacing between the primary conservation area and potential mining activities in adjacent seabed. The selection of these nine 400 X 400 km APEIs, has been criticized as possibly not including sufficient representative habitat similar enough to the potential mining areas (identified currently as the exploration contract and reserved areas administered by the ISA within the region) to ensure protection of the biodiversity that might be impacted by mining.An area to the east of the existing exploration contracts and reserved areas is known to have substantial mineral deposits; it is very similar to the adjacent exploration contract areas in its geology, environmental setting, polymetallic nodule abundance and nodule metal content. Because it is located in the northeastern extreme of the CCZ, this area is also likely to have relatively high densities of benthic life, compared with benthic communities further westward within the CCZ. Many options for the designation of this APEI are possible, but the area designation must accommodate the boundaries of the Exclusive Economic Zones of Mexico and France.This paper discusses why the selected region in the eastern extreme of the CCZ is a good candidate for designation as a new APEI.Keywords: polymetallic nodules, Marine Protected Areas, Clarion-Clipperton Zone, Areas of Particular Environmental Interest"

Jan 1, 2017

By K. Vanstaen, K. M. Cooper, S. Ware, S. L. Boyd

Remediation and restoration of offshore marine habitats is a relatively new concept with attempts in European regions largely being instigated by requirements of various strategic directives including Article 2 of the Habitats Directive (1992), the EC Water Framework Directive (2000, Article 2 of the OSPAR Convention (1992) and the developing European Marine Strategy Directive. A field experiment to establish the practicality of various options for rehabilitating the seabed on the cessation of dredging has been successfully set up. The purpose of this experiment is to investigate the practicality and effectiveness of gravel seeding as a potential restorative method that can be applied at marine aggregate extraction sites following cessation of dredging. Zone 2, within Area 408 (offshore Humber) was chosen as the experimental site as there is some evidence for persistence of sand which may have resulted from screening operations at this site.