Search Documents

By Ed Revoort, Robert Schippers

In Rotterdam in the Netherlands the project ‘De Zalmhaven’ is being developed. The project consists of the realization of houses, parking facilities, two residential towers of 70 m and a residential high rise of 215 m. An artist impression for the project is given in figure 1. For the high rise a new development in the use of large diameter, drilled piles with a steel casing has been successfully utilized. In this article the installation method of 65 m long steel drilled piles in two consecutive sections is presented. The settlements for the building (and the influence on its surroundings) have been analyzed in detail using 3D Finite Element calculations, which will also be discussed. Finally there is focus on the results of settlement measurements carried out during construction in relation to the settlement prognosis.

May 1, 2022

"Integrity tests refer to a variety of non-destructive tests (NDT) whose purpose is to measure or determine the quality and uniformity, and some- times dimensions, of cast-in-place concrete foundation elements. The tests are primarily aimed at detecting zones of poor quality concrete, voids, bulges, and/or necking.The non destructive integrity testing techniques in this section most generally used for drilled shaft testing are based on one of two physical principles - stress wave propagation or nuclear radiation. All of the stress wave methods involve monitoring a deliberately created vibration, usually of very low amplitude (strains on the order of ??). Some methods rely on direct transmission of the signal, while others rely on processing reflections of the imposed signal.The stress wave methods are inherently sensitive to vibrations from other sources, especially at frequencies that fall within the range of interest for the particular test being applied. Construction activity near the shaft being tested; such as: demolition jack-hammering, pile-driving, casing vibration, excavation and movement of track-vehicles are all known sources of interference that might render test data useless. The actual effect of such vibrations will vary with the type of activity, soil conditions and distance from the testing. The test operator must be able to recognize such interference, and the contractor should be prepared to cooperate with the testing personnel by stopping or moving the source of vibration. If this cannot be done immediately, testing should be postponed until the work in question is finished and the vibration source moved or shut down.NDT methods are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT methods do allow measurements of the quality of concrete placed in drilled shafts, which cannot be made from "topside" construction inspection. They should be considered supplemental to routine construction inspection as they do provide an additional level of quality control."

Jan 1, 2004

By Yoshinori Kurumada, Tatsuo Nagatsu, Keiji Uchida

"Cement deep mixing method has been utilized in the process of construction of an underwater tunnel in Singapore. The soil was improved by this method to prevent undesirable heaving of the soil below the excavated area. Quality control experiments approved the effectiveness of CDM method in increasing the strength of the soil and prevention of undesired heave of the ground. The process of the construction of this project and the quality control experiments results are discussed in this paper.INTRODUCTIONThe Marina Coastal Expressway is a 5.3 km long underwater highway tunnel with five lanes in each direction. It mostly comprises a twin box culvert structure (53.3 m exterior width and 10.89 m height) and was opened by the Land Transport Authority of Singapore (LTA).The contract zone C485 was the most challenging area of the construction; it involved a 700 m long underwater tunnel of which 400 m was built beneath the seabed at the mouth of the Singapore River. A double steel pipe sheet pile wall was built as a temporary cofferdam to keep water out of the excavation site, and the cut-and-cover method was used for excavation. In order to ensure a sufficient cross-sectional area for the flow of the Singapore River, the construction was divided into two phases focused on the left bank (Stage 1) and right bank (Stage 2).The Cement Deep Mixing (CDM) method was used to improve the ground, which comprised soft marine clay, to ensure safety during the excavation. The efficiency of this method in increasing the soil’s strength was approved previously. The design standard strength was quck = 800 kPa. Based on the study conducted after the construction, the average the Unconfined Compression Strength (UCS) of the soil stabilized by the CDM method was quf =3,000 kPa. This paper discusses the effect of the CDM soil improvement construction on the reduced displacement from the excavation and the quality control of the soil improvement."

Jan 1, 2015

By Nabil F. Ismael

Load tests were carried out to examine the ultimate bearing capacity of short, large diameter bored piles in connection with the construction of a multistory building on the Arabian Gulf in Kuwait. Testing included 0.45 m, 1.0 m, and 1.2 m piles installed through loose sand into a bearing stratum consisting of very dense cemented sands. All tests were carried out to failure. The base resistance and shaft friction were calculated using the Meyerhof method for a layered soil profile. The method employs the standard penetration test N-values. The results indicate that the piles are end bearing piles with a great portion of the pile capacity due to base resistance. The mobilized skin friction is small. The calculated pile capacities were very close to the measured values with the maximum difference not exceeding 10%.

By Fei-chiu Huang

A 17-acre landslide occurred in February 2001, on a slope below Via Bellota in the City of San Clemente, California. Three homes were destroyed and many others placed in jeopardy. The landslide, involving portions of five separate developments, continued to move significantly in the years following. Litigation ensued among the affected parties, and investigations continued through 2007. A mediated repair resolution was ultimately reached among the parties. The agreed upon repair consists of a multi-million dollar stabilization program that included grading, drainage, and structural systems. Part of the construction cost was offset by creating 4 new ocean view custom lots and 20 new mobile home lots. The landslide repair and slope stabilization design involved removal and replacement of portions of the landslide debris and construction of buttress and stabilization fills as well as installation of 74 shear pins in two rows. The shear pins were designed as 4-foot diameter by 50 feet in length and incorporated continuous W30x211 wide flange steel. The shear pins were designed to be installed 25 feet above the slide plane and 25 feet below the slide plane at each location. Construction of the 74 shear pins was initiated in 2008 and completed in 2009. Four-foot diameter holes were drilled by utilizing a truck-mounted, flight-auger-style drilling rig with a 4-foot diameter solid-flight auger. Prior to the installation of the shear pins, an engineering geologist downhole logged strategically selected holes to further evaluate the actual slide plane elevations. The wide flange steel shear pins were then lowered to the desired elevations and encased within 4,500 psi, Type V, 0.45 maximum water/cement ratio concrete. Inclinometers installed within four pin shafts and behind the pin rows indicated performance in accordance with the design. Slight to non-perceivable shear displacement was measured which mobilized the intended capacity at the monitored shear pins. No excessive slope movement was detected at any of the inclinometer locations during or after the construction period. Actual shear displacement of the steel wide flange elements was less than the movement anticipated before shear pin installation.

Jan 1, 2010

By Chengcan Wang, Jin-Tae Han, Young-Eun Jang

"The waveform micropile is a newly developed foundation type for increasing the bearing capacity with the created shear keys on the pile’s shaft. Analyzing the increment of resistance at the shear key zone is a crucial factor in the design of the waveform micropile. Hence, centrifuge tests were carried out employing six different models, including a waveform micropile in the axial loading condition. The analysis results of the load-settlement curves showed that the waveform micropile achieved a higher bearing capacity compared to the micropile without shear keys. In addition, the test results revealed that the load-settlement relationship was affected not only by the pile shape but also by the locations of the shear keysINTRODUCTIONA micropile is a small-diameter pile, typically constructed with a less than 300 mm diameter. Generally, the micropile’s construction involves drilling, grouting, and insertion of a reinforcement material, such as a thread bar. The micopile can be utilized in a variety of fields for reinforcing the foundations of existing structures. It also has advantages for accessing challenging areas like limited-access construction sites, including those with a low headroom space and adjacent structures, due to the small size of the construction equipment. Thus, since it was introduced in 1950 in Italy, the micropile has become one of the preferred solutions when other deep-foundation methods are not applicable to the site.Federal Highway Administration (FHWA) gives the micropile design implementation guideline of neglecting the end bearing due to its small diameter but considering the frictional resistance if the bond zone of the pile is in the soil or on a weak rock. The bearing capacity is considered primarily only if the micropile is founded on a high-quality sound rock (FHWA, 2005). Micropile design in South Korea is currently being performed based on the FHWA manual and taking into consideration the frictional resistance for the design as the pile generally sockets into a weak rock or soft rock. Moreover, the frictional resistance within the soil layer has usually been ignored, considering only the shaft resistance of the rocksocketed length in the conservative design. The design concept excluding the frictional resistance in the soil layer, however, may lead to an extension of the pile socket length, which will increase the construction cost. Hence, many researches have attempted to provide better design and construction methods to increase the bearing capacity in a cost-effective way (Juran et al. 2001; Sadek and Isam 2004; Tsukada et al. 2006; Finno 2002; Gomez et al. 2003; Seo et al. 2013)."

Jan 1, 2016

By Dan A. Brown

The foundations at the Huey P. Long Bridge in New Orleans presented special challenges for construction due to the requirements for very deep drilled shafts in the Mississippi River beneath the existing bridge structure. Drilled shafts were constructed to depths of approximately 200ft in alluvial soils using a rotator system with full-length segmental casing, and base grouted to improve axial resistance. This paper describes the design and construction of the work platform to provide access to the restricted-access site beneath the existing bridge, the approach used to construct the drilled shafts, and the results of a load test program to verify the axial resistance.

Jan 1, 2010

By Alexandra Weidle, Seffen Leppla, Rolf Katzenbach, Matthias Seip

"A lot of different deep mixing systems have been developed in the last decades for a wide spectrum of applications, e.g. retaining and foundations systems, soil improvement, sealing of toxic substances or dyke strengthening. The paper will deal with special aspects of constructions with deep mixing systems for infrastructures like soil improvement for cyclic loadings and underpinnings in difficult soil conditions by presenting cases from engineering practice.1. DEEP DRY SOIL MIXING FOR SOIL IMPROVEMENT OF RAILWAY TRACKS IN VERY SOFT SOILS1.1 IntroductionRailway tracks are set into vibrations by train passing. In very soft soil this leads to long-term deformations which lead to speed limits, temporary closings and big maintenance efforts. The energy of the dynamic loading is transmitted into the soil by compression and shear waves and at the surface by rayleigh waves (Wood 1968). The expansion of the waves are influenced by•,thickness of the soft soil layer•,density of the soft soil layer•,stiffness of the soft soil layer•,saturation of the soft soil layer•,frequency of the dynamic loadingThe frequency of the dynamic loading depends on the train velocity and the distance of the wheels and wheel sets. If the frequency of the dynamic loading is in the range of the natural frequency of the soft soil layer the vibrations increase extremely (Lieberenz et al. 2003). As a result the long-term deformations will increase as well.To avoid these long-term deformations and the resulting operation restrictions and maintenance efforts an adequate soil improvement is necessary. For the optimization of the soil improvement field tests have been carried out.1.2 Experimental field testsThe field tests have been carried out at a 300 m long test track with five different setups, each 30 m long:•,test track TS 0: no soil improvement•,test track TS 1: soil improvement with single lime-cement-columns 5.9 m deep (Figure 1a)•,test track TS 2: soil improvement with single lime-cement-columns 5.9 m and 10.4 m deep (Figure 1b)"

Jan 1, 2015

By D. Y. Peng

A Large Sub-structure with open top of S.Y.P. float line requires a 90m x 50m in plan and 13m-deep excavation in soft soil, Shanghai. The geological conditions in site are rather severe. The technology specifies that no permanent braces nor partition walls are allowed to be constructed inside. After a series of discussions the scheme of semi-gravity type cellular D-walling without any braces or earth anchors is finally adopted and successfully executed by SFEC. This paper deals with the technical problems in the design, construction and in-situ monitoring we met with in this difficult project.

Jan 1, 2010

By Michael Cianchetti, Nadir Ansari, Matthew Janes

"PROJECT DESCRIPTIONThe R C Harris Filtration Plant underwent an expansion to install an underground sludge treatment capability consisting of a series of underground tanks within stepped excavations 12m (39 ft) and 10m (33 ft) deep into compact, wet sands over stiff clays and clayey silts.Concerns regarding the original structure influenced designers to set the lateral deflection limit for the proximal front footing at 4mm (1/6 in), (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Through extensive Fast Lagrangian Analysis on Continua (FLAC) and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept and met deflection concerns.GEOTECHNIQUEThe hillside site drops 14.5m (47.6 ft) over a distance of 53m (174 ft) between the existing Filter Building on the north and the Services Building on the south. The soils adjacent to the Filter Building consist of 6m (20 ft) of sandy fills, to the footing elevation, over compact sands and layered dense sands and silts to a depth of 10m (33 ft) below existing footing. Beneath the silts lies a 10m (33 ft) thick stiff clayey silt, 2m (6.6 ft) of sandy silt till (containing cobbles and boulders) and an artesian gravelly sand at a total depth of 30m (98.5 ft).The tender information was deemed inadequate to accurately determine soil parameters for a finite element analysis. As a result, the design-build team performed pre-tender Cone Penetrometer Testing (CPT), including dynamic analysis. The CPT data indicated stratigraphy consistent with the conventional bore hole exploration (SPT results) however, the CPT data provided consistently superior soil strengths. The CPT data indicated the sands and silts were dense to very dense throughout their full thickness. The clayey silts below the sands were found to have shear strengths in the 100 to 200 kPa (14.5 to 29 psi) range with an Over-Consolidation Ratio (OCR) ratio of 1.5 to 2. The dynamic analysis, while low strain, indicated very competent behavior with Young’s Modulus values in the 200 to 350 MPa (29,000 psi to 51,000 psi) range. The CPT derived shear moduli and OCR values were vital in determining the soil engineering parameters used for the FLAC analyses."

Jan 1, 2007

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By Tony Suckling

"As we head toward the United Nations Climate Change Conference in Copenhagen in December, the environment and sustainability will become headline news for a while. Governments are expected to agree to a set of binding targets to reduce carbon emissions probably before 2020, and certainly before 2050. This will, in effect, initiate a low carbon economy in many parts of the world. Sustainability has mainly been rhetoric so far, the exceptions being projects for those looking to the long-term future and not for short-term financial gains.The probabilities and consequences of negative impacts on the environment and on society over the short term and in the long term can be assessed and mitigated, but mitigation often adds cost. Also, we cannot know what technologies will be available, say 1,000 years into the future, which is about 40 generations of our society. It is easier to have a connection with 100 years into the future, which is only about 4 generations. Individuals may have a different sense of sustainability, and place a different value on mitigation, its cost, its importance and its potential impacts.Sustainability means different things to different parties on a construction project. For example, a land developer is likely to have a different view on the design in terms of sustainability than that of the designer. The developer may also likely to be more interested in sustainabiliy if there are tangible economic benefits that might accrue. Achieving sustainability on any project, leads to conflict between competing interests or demands cooperation between the economic and technical sectors involved. The foundations for a building or bridge, by definition, need to interact with the ground whose behaviour cannot be dictated by man. The aims of sustainability are the same as for the building or bridge, both of which are constructed of manmade materials, but it is less clear how they should be achieved. An example is the driven pile that does not produce spoil waste, but is likely to be too noisy to be acceptable in an urban environment. This then begs the question, should the public accept the nuisance of short-term pile driving to achieve a more sustainable foundation? Additionally, the question has to be asked, can the deep foundations industry develop its techniques and products to help make them more acceptable and appropriate more often than is possible now?"

Jan 1, 2009

By Filippo Maria Leoni, Wesley Schmutzler

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 90 inch forced sewer main relocation and to improve the soils for the base of a new drainage channel. The project is located just east of San Juan and south of the Horizon Port. The soils to be improved consisted of fill, marine clay, organics (peat) and the foundation clay layer. A preconstruction soil investigation campaign was performed to assess soil properties and to retrieve samples of the different soil layers for the laboratory Bench Scale Testing program (BST). The BST was conducted using various binder contents and water/cement ratios in each of the soil types; the selection of the different combinations and dosages was based on past extensive experiences on similar materials. Following the laboratory program, a full scale Field Test (FT) was done installing several DMM elements to verify the results of the BST and fine tune the construction parameters. Each element consisted of two 5.5 feet diameter overlapping mixing augers installed simultaneously to a depth of approximately 60 feet using a SOILMEC SR-90 dual axis drilling rig. The FT construction and post-construction coring results showed significant differences between the lab study and the actual field conditions. This paper will highlight these differences and the importance of performing both pre-construction laboratory and field tests in order to ascertain the proper mixing parameters in the different soil layers.IntroductionThe Puerto Nuevo project consists of the stabilization of a major drainage channel using Deep Mixing Method (DMM) and the relocation of a 90 inch forced main sanitary sewer outfall. The first portion of this project was a 40 x 16 x 2,000 foot box culvert installed in 2004. In order for the drainage system to be completed and function properly, the 90 inch forced main needed to be lowered about 20 feet to allow for proper drainage.DMM was chosen by the US Army corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The overall layout of the project is shown in Figure 1. The DMM is arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for ZONE A and B as an example. (Figure 2) The total amount of soils to be treated by DMM is approximately 84,000 cubic yards up to a maximum depth of 57 feet from ground surface and an Area Replacement Ratio of 100%.The equipment used to perform the DMM is a Soilmec SR90 twin-shaft jet assisted deep mixing rig (Figure 3) coupled with a LODOS 30 grout plant and two Soilmec 7T-500J high pressure pumps."

Jan 1, 2015

By John P. Turner, Steven S. Dapp, Dan A. Brown

"The Goethals Bridge Replacement (GBR) spanning the Arthur Kill Waterway between Elizabeth, NJ and Staten Island, NY consists of a dual-span 1,982.5-ft long cable-stayed bridge with approach spans of 2,545 ft on the NJ side and 2,788 ft on the NY side. The bridge is supported on over 200 drilled shaft foundations ranging in diameter from 4.5 ft to 10 ft and socketed into Passaic Formation siltstone. Drilled shaft resistances for design were based on load tests as described in a companion paper (Dapp et al. 2016). This paper presents the main foundation design considerations and challenges. The approach to construction of the rock sockets, with a focus on quality in order to support the use of high nominal values of side and base resistance, is described. Lessons learned from this project and their application to future similar projects are presented.INTRODUCTION AND BACKGROUNDThe Goethals Bridge Replacement (GBR) project is a Public-Private Partnership (P3) that represents a major milestone for the Port Authority of New York and New Jersey (PANYNJ) in its distinguished history of bridge building in the greater New York City metropolitan area. The new bridge will replace the existing Goethals Bridge, named after Major General George W. Goethals, Chief Engineer of the Panama Canal and the first consulting engineer for the Port Authority. The existing Goethals Bridge along with the Outerbridge Crossing and the Bayonne Bridge comprise the three Port Authority bridges connecting Staten Island with New Jersey. The existing Goethals Bridge and the Outerbridge Crossing are cantilever truss structures and both opened on the same day in 1928. They were designed by J.A.L. Waddell under the supervision of the eminent engineer Othmar H. Ammann (1879-1965), who was the designer of many other iconic bridges in the NY City area including the Bayonne Bridge (1931), the George Washington Bridge (1931), and the Verrazano Narrows Bridge (1964). The designer of record for the replacement Goethals Bridge is Parsons Corporation, which is the successor firm of Robinson & Steinman, whose principal David B. Steinman was also a notable NY area bridge designer and a contemporary and rival of O.H. Ammann.The replacement Goethals Bridge is supported on over 200 rock-socketed drilled shaft foundations. Each main pylon tower is supported on a group of six 9-ft diameter drilled shafts and each anchor pier is supported by two 10-ft diameter shafts. Each approach pier consists of a two-column bent with each column supported on a rock-socketed drilled shaft. A rendering of the Main Bridge crossing the Arthur Kill is shown in Fig. 1."

Jan 1, 2016

By Dale E. Berner

A new navigation dam at Olmsted on the Ohio River will be built "in-the-wet" using a lift-in construction method by the Washington Group/Alberici Joint Venture for the U.S. Army Corps of Engineers, Louisville District. Up to 4,000-ton precast concrete dam shell segments will be prefabricated on the Illinois riverbank and lowered into the river on a marine skidway and cradle. A 4,500-ton capacity catamaran crane barge will lift the precast concrete shells and lifting frames from the cradle, and transport them partially submerged to a piled foundation pre-installed underwater. Tremie concrete will be used to compositely connect the shells, piles and sheet pile cut-off walls. This paper focuses on the pipe-pile foundations for this half-mile long navigation dam, and for the temporary precast yard and marine skidway. The dam foundations are designed to resist large ground motions from the New Madrid Fault Zone, and selected production piles are designed to serve as landing piles to support the shells during the construction process. Specific foundation issues addressed in the paper include: pile load tests; production field testing requirements; controlled fixity 24-inch diameter pipe-pile design including seismic considerations; cut-off wall design; sheet pile cellular fixed weir design; isolation jOint design; and temporary works foundation designs for both the precast yard and the marine skidway, including testing of 42-in diameter pipe piles.

May 11, 2007

By Paul J. Sabatini

Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed. During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor?s QA/QC program should be increased to achieve a foundation system with the required level of reliability. Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially ?at-risk?. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.

By W. G. K. Fleming

Mr P. Bermingham introduced paper 9.1, describing the development and trials of a new pile load-testing technique that the Authors had termed "Statnamic". The system involved launching a test weight mounted on the head of the pile by igniting chemical fuel in a pressure combustion chamber between the pile head and the test weight. The expansion products from the burning fuel generated large pressures which were used to launch the weight upwards at high velocity. The reaction from this force generates an equal and opposite force at the pile head. This force is typically of much longer duration compared with, for instance, dynamic load testing by drop hammer. In addition the pile experiences a much lower acceleration - typically of less than one g. Because of the long duration blow, the pile is loaded at below its natural frequency and is therefore under a uniform high stress over its full length throughout the duration of the test. The pile behaviour is not dominated by the complex action of an impulsive stress-wave as with standard dynamic testing. The test technique is thus essentially quasi-static. It was anticipated that a ram test weight of 16 tonne would be sufficient to provide the test reaction for a 600 tonne load test. It was pointed out that the device was still at the research stage, but had yielded encouraging results to date. Testing would proceed from model testing and computer simulation to full scale field testing.

Jan 1, 1991

By Ashley Shirer

Have you heard a geotechnical engineer rail against using the word "dirt"? The typical maxim is: "It's not dirt, it's soil!" This axiom is so prevalent that it is joked about on the construction site. How did we get to the point in our profession that soil is too technical to understand, while dirt is not viewed as important? Take a moment and think about the images that come to mind by the word soil. Responses range from the sand at a playground to the mud that sticks to the bottom of your shoe, the dark loam found in gardens to the firm earth under your feet. But do you know where the term soil originated? Or how it was intended to be used? This article looks at how word choice can lead to very different motivations for owners, designers and constructors.

May 1, 2023

By Stephan Fisch, Franz-Werner Gerressen

"The use of cut-off-walls (COW) for the open pit coal mines has been used for decades. They have been used to reduce the negative hydraulic impact to the surrounding area caused by the open pit mining. The pile-guided trench cutting system is a worldwide unique technique, originally developed by the engineers of the mining companies themselves. It guarantees a continuous, joint free, COW during a continuous installation process. At this specific site in Welzow, this technique has been pushed to new limits in order to address the local lake region. Depth capability has been designed to about 430 ft (130m), proven are already depth of about 360 ft (110m) at a constant trench width of 39 inch (1000 mm). This project is approximately. 6.8 miles (11 km) long of COW, scheduled to be completed in 12 years period. About 2.05 miles (3.3km) have been installed, which is equivalent of about 3.5 Million ft² (330,000 m²). The system flushes special clay which forms a filter crust at the inner surface of the trench. Only natural clay resources used, in order to achieve the cut-off effect (colmation effect). The paper explains the installation process of the cut-off-wall as well as the equipment systems developed specifically for this project. After a successful start of the first phase of the project, the next step in the advancement of the equipment is already underway to enable the installation of greater depth to approximately 490 ft (150 m +) and beyond. The next generation equipment system is scheduled to start operation around 2018 INTRODUCTIONThis Serbian saying “Bóh je stworil Lužicu a cert je zaryl brunicu – God created Lusatia and the devil buried brown coal underneath it.” captures local communities’ ambivalence towards lignite.Lusatia is an almost entirely flat stretch of land between the Elbe and Neiße rivers dominated by glacial sands. On the surface, the heathland and woodland is hardly noteworthy. However, three large lignite mining regions, two in Brandenburg and one in Saxony, in the east part of Germany, divert the attention to underground level, down to depths of up to 120 meters. Here, seams crisscross the earth like ribbons. They were formed in the Tertiary around 17 million years ago.The mining of the lignite started almost 200 years ago. To enable open pit mining, a suitable dewatering system was required. At first, wells and drainage system were used. With the increasing demand to go deeper to enable full use of the existing resources with greater mining depth, a decision taken back in the 60th of the last century, the amount of water which had to be pumped increased dramatically. In peak times, approx. 1.57 Billion cubic yards per year (1.2 Billion m³/year) had to be pumped. This led to a lowering of the groundwater level for up to 230 ft (70 m), impacting the regional lake landscape. In order to reduce the influence on the water balance, and bring the water level back to pre1970th, a first development took place to implement the use of specific COW system to depth of about 147 ft (45m)."

Jan 1, 2017

By Tony P. Suckling

This paper presents a case study of a piling contract undertaken at Keble College in Oxford in the year 2001. Unusually, and for the first time in the United Kingdom, piles were successfully constructed containing a network of plastic pipes, which are subsequently to be connected to the heating and cooling system for the new building. The pipes cast in the piles facilitate the transfer and storage of geothermal energy between the structure and the underlying ground mass, allowing the new building to be both heated in winter and cooled in summer economically and in an environmentally friendly way. The philosophy of the geothermal pile technology is presented, together with the modified pile construction techniques employed on the site.

Jan 1, 2002