Search Documents

By G. Vibert Douglas

IN a previous paper by Douglas and Gillies (1), a simple field test was given for gold. Later work by the present writers, and by others who have kindly written to us, shows that the test is not as satisfactory as it was hoped. In many cases, the gold mirror is completely obscured by a dense precipitate which, up to the present, it has been found impossible to remove. After many attempts, we have temporarily given up the iodine test and have been working on a simple pyridine reaction based on the work of Putnam, Roberts, and Selchow (2): The ore to be tested is ground to a fine flour. Place half a gram of this powdered ore (an amount that will cover a Canadian ten-cent piece, not heaped) in a six-inch test-tube and add 5 c.c. of aqua regia. The aqua regia. should be made up on each occasion, using four parts of hydrochloric acid and one part of nitric acid, both concentrated. Shake the solution in the test-tube for about one minute and allow to settle until dear. The rime to settle may be 30 to 60 minutes. When dear, a drop of the solution is with-drawn with a fine, dean eye-dropper or capillary tube and placed on à small glass plate. A slide such as is used for mounting rock sections is suitable. Now place an equal sized drop of pyridine solution on the plate beside that of the aqua regia solution to be tested. The pyridine solution, containing nine volumes of hydrogen bromide to one volume of pyridine, can be made up in advance and carried in a glass-stoppered bottle. Join the two drops with a glass thread or fine, dean stick, and allow the merged drops to stand undisturbed. I t is well to place the slide on a piece of white paper so that the presence of the crystals which may form can be easily seen. The time for their formation will vary with the amount of gold present, but the slide should be allowed to stand for at least 30 minutes before negative results are reported. A hand lens of at !east ten magnifications is essential. If gold is present, minute red crystals will form around the margin of the drops as these drops slowly evaporate.

Jan 1, 1938

By R. P. Viljoen, A. L. Sokolov

"The distribution of mineralized provinces is analyzed on the basis of their genetic link with specific blocks of the earth's crust including ancient platforms, mobile belts and zones of tectonicmagmatic activation. Mobile and fold belts surround the Siberian platform in Russia and the Kaapvaal craton in South Africa, with decreasing age zoning away from ancient platform margins. The main differences in the geological development of the two cratonic areas are: (1) the long period before the final stabilization of the Siberian platform (3600 Ma to 1600 Ma) and the comparatively short period of time for the stabilization of the Kaapvaal craton (3600 Ma to 3050 Ma) and (2) the intensive multiple activation of the marginal zones of the Siberian platform and the tectonicallycontrolled, magmatic sedimentary, intracratonic activity, typical of the Kaapvaal craton. Mineralization of the Siberian platform is largely characterized by marginal reactivation zones of differing ages although mineralized intracratonic Cu-bearing basins of Proterozoic age are also known. Mineralization of the Kaapvaal craton is mainly related to the formation of the intracratonic basins i.e., Witwatersrand (Au, U) and Transvaal (Au). The latter is characterized by multi-age volcanic-intrusive activity including the emplacement of Bushveld Complex (Cu, Ni, Pt, Cr, Au, V). The Siberian platform is characterized by the prolonged development of inherited mineralization from Archean until the late Mesozoic. The main period of mineralization in the Kaapvaal craton is restricted to the middle Proterozoic.The Baykal-Patomskaya and Namaqua-Natal mobile zones occupy similar positions adjacent to the Siberian and Kaapvaal cratons, respectively, and demonstrate similar modes of metallogenic development: i.e., the early formation of exhalative Pb-Zn-Cu deposits during the early stage and magmatic Cu deposits during the late stage. The more remote mobile belt near the Siberian platform, the Trans-Baykal, is characterized by intensive multi-age mineralization (Wo, Mo, Sn, fluorite), related to a period of tectonic-magmatic activation. The Saldania Belt occupies a similar position near the Kaapvaal craton but is known for its poor Au, and Cu mineralization. It does, however, have some similarities with Trans-Baykal Belt in regard to Mo-W bearing granitoids.The phenomenon of interference of geosynclinal, orogenic, platform, and tectono-magmatic activation regimes is known for the Russian section of the Pacific Ocean Volcanic Belt."

Jan 1, 1994

By Deni Côte, Michel Dagbert, Marcel Vallée

"Greater reliability of mineral deposit and reserve estimates can be attained through better quality control of the data and information acquisition, and the estimation processes. This paper reviews the following key requirements:1. greater awareness of the significant figures of both data and estimates, and better understanding of the probabilistic aspects of the estimates, their confidence limits and margins of error;2. greater reliability of the information that supports the estimates, by more explicit and more rigorous methods and standards for data acquisition and for interpretations;3. more quantitative estimations of geological/mineral continuity, based on improved three dimensional sampling patterns and the use of geostatistics; and 4. better integration at the project engineering and mine production stages, of the mineral deposit characteristics and mining method constraints, for more efficient mineral recovery and mine quality control.RÉSUMÉUne plus grande fiabilité des estimations des gisements et des réserves minières requiert plus d'emphase sur le contrôle de la qualité de I ‘acquisition de l'information et du processus d'estimation. Les exigences suivantes sont revues:1. le respect du niveau d'exactitude des données et des estimes en n'utilisant que le nombre approprie de chiffres significatifs des observations et mesures, et en exprimant le niveau de confiance et la marge d'erreur des estimations;2. l'amélioration de fa fiabilité des données par des normes plus rigoureuses pour leur acquisition et leur vérification, et par des méthodes plus systématiques d'interprétation et de modélisation;3. l'estimation plus rigoureuse de la continuité des minéralisations dans les trois dimensions des gisements, par des patrons échantillonnages mieux adaptes awe paramètres géologiquement minéralogiques, et par l'utilisation des méthodes géostatistiques; et4. l'intégration plus poussée, particulièrement lors de la planification de l'exploitation minière, des caractéristiques des gisements avec les contraintes des méthodes d'exploitation, pour améliorer la récupération et le contrôle de la qualité en exploitation."

Jan 1, 1993

By Chri Langille, Dougal McCreath, Samantha Espley

"In 1993, trials of two innovative applications of liner support involving the replacement of bolts in the ground support system were undertaken at Inco mines. The first trial involved an evaluation of the effect of dynamic loading on mesh-reinforced boltless shotcrete in a sub-level cave mining area on 2400 level at Stobie Mine. The second trial involved an evaluation of the MIROC Mineguard spray-on liner as a replacement for bolts and screen support, or as a replacement for screen support alone, in a topsoil heading of a bulk, VRM (vertical retreat mining) stope on 3240 level at Lower Coleman Mine.In the Stobie Mine trial, an uppers retreat heading was supported using a two-pass system. First, shotcrete was applied 2 inches thick, followed by pinning of mesh screen to the back and walls. A second pass of another 2 inches of shotcrete was then performed. For recovery of the ore zone, a vertical slot was created using a Borepak blind boring machine. The uppers rings were blasted, one or two rings at a time, starting at the slot and retreating out of the heading. During blasting of the production rings, blast monitoring was used to record the ppvs (peak particle velocities). For a series of 5-ring blasts, the maximum ppvs were measured to be 0.4 m/s (16 in./s) with a maximum charge weight per delay of357 kg (800 Ib). Six 5-point convergence measurement stations were set up and after each blast the total rockmass convergence was measured using a tape extensometer. Although a maximum displacement of 100 mm (4 in.) was measured, the shotcrete still managed to provide some support junction. A support damage assessment was also done to try and relate blast vibration to effectiveness of the mesh reinforced shotcrete liner. This trial demonstrated the effect that blasting has, on a support system, and it also demonstrated the necessity of having the mesh reinforcement properly placed within the shotcrete."

Jan 1, 1995

By P. E. Weidmark

"PART I - Published PapersBallivy, G., and Dupuis, M., ""Laboratory testing for the design of grouted rock anchors""; Proc 6th Pan Am Conf Soil Mech Found Eng; Lima; 1:277-291; 1979.Ballivy, G., Ladanyi, B., and Gill, D., ""The effects of moisture content on the strength of fissured rocks""; Proc 1// 1ntnl Congr 1.A.E.G.; Madrid; //:2:7-16; 1978.Baumgartner, P., and Stimpson, B., ""Development of a tiltable base friction frame for kinematic studies of caving at various depths""; Int J Rock Mech Min Sci Geomech Abstr; 16:4:265-267; 1979.Bawden, W.F., and Roegiers, J.-c., ""Discussion and interpretation of the mathematics governing radial flow in a single horizontal rock fracture""; ISBN 07727-7002-6; Dept Civil Engng publication 79-11; Univ Toronto: 134p;1979.Chatterji, P.K., Smith, L.B., and Insley, A.E., ""Construction of Saline Creek Tunnel in Athabasca oil sand""; Can Geotech J; 16:1:90-107: 1979.Coates, D.F., and Gyenge, M., ""A case history of pit slope design""; Proc 4th ISRM Congr; Montreux, Switzerland; Sept 1979; 1:Theme IV:591-596; 1979.Crawford, A.M., and Curran, J.H., ""A dynamic direct shear machine for determining the time-dependent behaviour of rock joints"": Dept Civil Engng publication 79-08; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A displacement discontinuity approach to modelling the creep behavior of rock and its discontinuities""; Dept Civil Engng publication 79-09; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A higher-order displacement discontinuity element""; Dept Civil Engng publication 79-10; Univ Toronto; 1979.Cruden, D.M., ""A computer-based system for rock mass description""; Proc 1// Intnl Congr I.A.E.G.; Madrid; //:2:155-159; 1978.Cruikshank, D.J., and Curran, J.H., ""A.B.LE. approach to modelling of fluid flow in fractured rock masses""; Proc 7th Cdn Congr Appl Mech; May 1979; Sherbrooke, Que; 887-888; 1979."

Jan 1, 1980

By P. E. Weidmark

"PART 1-Published PapersAllcott, G.A., and Archibald, D.E.; ""Description of pillar behaviour at Heath Steele Mines""; Can Min Metall Bull; 74:834:80-87; 1981.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of rock Mechanics; 3:32-33; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:37-38; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:38; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses"" ; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:41; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:42; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:46; 1979.Baar, C.A.; Discussion of Theme 2: ""Tectonophysics""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:60; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3: 116; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:116-117; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:117; 1979.Baar, C.A. '; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:118-119; 1979.Baar, C.A.; Discussions (2) of Theme 4: ""Underground openings""; Proceedings 3rd Congress lntnl Soc of Rock Mechanics; 3:119; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:120-121; 1979."

Jan 1, 1982

By Stuart McTavish

"The Brunswick Mining concentrator processes 10,000 D.S. T. per day of a complex sulphide ore. Four separate concentrates- zinc, lead, copper and bulk-are produced by selective flotation. Several major changes have been made to the Brunswick flotation circuit to improve the process and control. This paper will describe the present flotation practices at the Brunswick Concentrator. Special emphasis is given to the conversion of two of the primary circuits to an SO2-aeration flowsheet, and to the addition of a new secondary zinc flotation circuit that produces a zinc concentrate from the plant tailings. IntroductionBrunswick Mining and Smelting Corporation operates a zinclead- copper and silver mine and concentrator near Bathurst, New Brunswick. Since the start-up of operations in 1964, the flotation flowsheet has undergone major modifications to process the increased tonnages and to produce a greater number of concentrates. The flowsheet for the concentrator as it was in 1971 has been described by Neumann and Schnarru) and by Ersklneco. Since then, in 1971, the No.6 concentrator was converted from bulk flotation to selective flotation to produce a copper, lead and zinc concentrate. A separate zinc upgrading circuit was installed in 1972 and a bulk flotation or dezincing circuit, which reduced the zinc in the lead concentrate, was started in 1973. In 1976, the secondary zinc circuit was initiated.In addition to these new circuits, changes have been made to the existing circuits to simplify their operation."

Jan 1, 1980

By Robert B. Parsons

"Finance Minister Paul Martin's first budget disappointed almost everyone. The business sector was disappointed at the some what feeble attempt to grapple with the country's deficit. The mining industry was disappointed by tax proposals regarding mine reclamation that fall short of the industry's needs. Has anybody been happy with a federal budget? Federal Budget DisappointsThe federal government's budget papers that were tabled on February 22, 1994, contained a rather bizarre mixture of unrelated tax proposals. The budget signals an unexpected attack on the tax treatment of debt settlements, on certain types of corporate reorgani2ations, and on income earned by foreign affiliates. This is an old style budget, which proposes a pot pourri of technical changes and policy initiatives. Mine ReclamationEffective February 23, 1994, a taxpayer's contributions to a prescribed mine reclamation trust fund will be deductible as a current expense. The budget papers do not provide a definition of what will constitute a ""prescribed"" trust: this definition will surface in due course. However, the budget papers indicate that:• income earned in such trusts will be subject to tax each year;• all withdrawals from the trust (including income already taxed) will be included in computing the income for tax purposes of the recipient;• reclamation costs will continue to be fully deductible at the time incurred; and • contributions, trust earnings, and withdrawals will not be taken into account for the purposes of determining a taxpayer's resource allowance."

Jan 1, 1994

By E. Czech

Hydrogen generated through aluminum-assisted water split reaction is a novel, efficient and environmentally friendly method. It has been found previously that the passivation of aluminum can be prevented in neutral (pH=7) or near neutral pH conditions in water by grinding aluminum with a catalyst, such as A12O3, SiO2 or SiC. Recently, the best results have been obtained by using water-soluble inorganic salts (WIS), ground with aluminum. The massive, rapid corrosion reaction of the Al-WIS system which takes place in regular tap (or marine, or ground) water can be utilized to produce hydrogen by aluminum-assisted water split reaction, in-situ, on-demand. The reaction offers clean, low-cost, environmentally benign and entirely recyclable technology for on-board on-demand hydrogen generation. Besides pure gaseous hydrogen, only pure solid aluminum hydroxides AlOOH or Al(OH)3 are formed as the reaction products. The hydrogen yield and Al-WIS reaction efficiency are high. From 1 g of mechanically alloyed aluminum powder, up to 1.25 liters of hydrogen were generated, i.e. efficiency up to 92% was achieved. The amount of hydrogen and hydrogen generation rate depend on various reaction parameters. The effect of chemistry and concentration of additives, water temperature, powder particle size and milling conditions on the reaction kinetics will be presented and the possible process mechanism will be discussed.

Jan 1, 2005

By C. O. Aksoy

Operating the underground marble quarries effectively, it is important to evaluate the deposit blocks economically which are affected by the suitability of the topography and configuration of bedding. The joint sets within the deposit and the spacing between these discontinuties are also of great importance. In this study, the marble deposits that could be geomechanically eligible for underground excavation have been selected throughout Turkey and these selected reserves have been classified accordingly by Q-Rating System. These classified marble deposits that forms groups of 1,2, and 3 (groups were determined by evaluating the O-rating, topography, quarry situation, cracks, joints etc.) are convenient for this type of production. Nevertheless, when the auxiliary factors (topography, location, production method etc.) regarding the deposit have also been investigated, the most convenient sub-group of deposits (Afyon Tiger Skin, Burdur Beige, Diyarbakir Pink and Mugla White) have emerged. The sizing of the pillars have been performed utilising Bieniawski?s stress profile. The LAMODEL software, developed by National Institute for Occupational Safety and Health (NIOSH), USA and run under the laminated displacement discontinuity method, has been used to size the pillars. This work brings in a novel opportunity to Turkey, in which no underground marble quarry has been attempted up-to-date similar to its several examples in Italy, USA, etc. This study serves as a reference for the marble operators and for the pioneering application of laminated displacement discontinuity method in hard rocks.

Apr 1, 2005

By E. W. Johnson

"The current increase in gold price may presage a resurgence of gold milling plants in Canada similar to that of the thirties. Because the industry has been at a low ebb for almost two decades, future operating responsibilities will likely devolve upon personnel with limited cyanidation experience. My comments, which may seem elementary to experienced operators, are directed towards these industry newcomers to highlight operational features in cyanidation which forty years' experience has shown me to 0e of importance. A brief review of what actually takes place in a cyanide circuit may help give a better understanding of the topics to be discussed.These will include: (1) expose the gold (2) dissolve the gold(3) make solid/liquid separation(4) recover the gold from solution.1. Expose the GoldThe chemical key to gold recovery by cyanidation lies in the ready solubility of the metal in a relatively weak solution (0.04%-0.075% NaCN equivalent by weight) of calcium or sodium cyanide. Obviously, dissolution cannot start unless the cya1ide is in contact with the gold. As an analogy, the yolk of a hard-boiled egg can oe taken to represent the gold particle and the egg white and shell, the surrounding gangue or sulphide host. As the sl1ell and white must be fractured to expose the yolk, similarly the surrounding gorngue or sulphide host must be broken or fractured to enable the cyanide solution to contact the gold."

Jan 1, 1979

By A. L. Mular

"IntroductionSince the mid -1960s, automatic control of grinding circuits has become the rule, to avoid losses attributable to frequent circuit upsets associated with uncontrolled disturbances such as ore hardness variations. Higher capital costs of grinding equipment and corresponding operating costs-especially with respect to energy consumption-are major factors that continue to stimulate interest in grinding control.Grinding circuit control strategies depend upon the control objectives defined by the processing plant and are subject to constraints such as: maintain final per cent solids within some range, do not transport steel ball s out of the discharge trunnion, or do not overflow or empty the pump box and so on. Constraints depend on the nature of equipment employed within the grinding circuit and may actually determine the characteristics of the control scheme. Typical control objectives are:1. Maintain final particle size at set point by ,a. manipulation of fresh feed rate with circulating load maintained by manipulation of pump box water addition rate, orb. manipulation of pump box water addition rate with circulating load maintained by manipulation of fresh feed rate, where the methodology utilized to accomplish either (a) or (b) is dependent upon equipment/circuit constraints such as the availability of a variable speed pump.2. Maintain circuit throughput at a maximum by,a. manipulation of fresh feed rate subject to constraints on final particle size and variables such as power draw, circulating load and mill overload.3. Maintain mill load at set point by a. manipulation of fresh feed rate subject to constraints such as on power draw.4. Maintain mill power draw at set point bya . manipulation of fresh feed rate subject to mill load constraints. Often, a grinding control objective is dictated by the recovery vs fineness-of-grind characteristic that exists for downstream separation circuits. When recovery is relatively insensitive to size, maximum throughput in the grinding circuit is advantageous.The purpose of this paper is to review control strategies for primary ball mill grinding circuits, rod mill/ball mill grinding circuits and semi-autogenous grinding mill circuits. Primary sensors employed are highlighted and modern trends are documented briefly."

Jan 1, 1989

By M. R. Babcock

"The Rabbit Lake story began in the late sixties and will continue well into the twenty-first century. It is a story of success, of multiple ore body discoveries, of unique systems, and new methods made possible through innovative and state-of-the-art design. Two quite different geological systems host the five ore bodies mined, or slated to be mined. These two systems have yielded two distinct ore types, each with characteristic mineralogical properties and each requiring its own specific mill circuit.Emphasis on communications and our unique systems have led to a satisfactory and fulfilling work environment resulting in the historically low employee turnover which has contributed to the operation success.A comprehensive environmental study after twelve years of operation has given the Rabbit Lake Operation a completely clean bill of health. INTRODUCTIONRabbit Lake can be described as Saskatchewan's first highgrade uranium mining operation, which set the stage for the province's current role as the leader in uranium mining throughout the western world. The importance of the Rabbit Lake operations - past, present and future.LocationThe Rabbit Lake operation is located in northeastern Saskatchewan (Fig. 1)- 805 km north of Saskatoon, Saskatchewan, and 814 km northeast of Edmonton, Alberta. OwnershipGulf Minerals Canada Limited discovered the Rabbit Lake deposit in 1968. Mining operations began in 1975and were operated by Gulf until purchased by Eldorado Nuclear Limited in 1982. In 1988, Eldorado merged with Saskatchewan Mining Development Corporation (SMDC) to form Cameco-A Canadian Mining &. Energy Corporation. The new corporation is one of the world 's largest uranium companies.Cameco's $1.5 billion in assets include the Rabbit Lake uranium mine (Cameco 100010); the Key Lake uranium mine (Cameco 66.67%; Uranerz Exploration and Mining Limited 33.33%); the Cluff Lake uranium mine (Cameco 20%; Amok Ltd. 80%); the Fuel Services Division at Blind River and Port Hope, Ontario (Cameco 100%); and a 100%); and a 48.75% interest in the Cigar Lake uranium deposit which is now at the test mining stage (Cogema Canada Ltd . 32.625% ; Idemitsu Uranium Exploration Canada Limited 12.875%; Corono Grande 3.75%; Korea Electric Power Corporation 2%). In addition, Cameco is involved in a number of base and precious metal explor ation projects."

Jan 1, 1989

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By Youngjib Ham

Understanding energy performance of existing buildings is vital to increasing their efficiency and reducing the overall energy consumptions. This entails facility managers to systematically monitor building energy performance and reliably identify and analyze potential problems. Currently, infrared thermography is widely used as a primary diagnostic tool for the detection of building performance problems. Nonetheless, applications of thermal images for building inspection are mainly restricted to manual and labor-intensive identification and qualitative assessment of heating or cooling loss. Automated identification of potential problems and reliable cost analysis of the associated energy loss can help homeowners to minimize financial risk of retrofits and maximize energy savings. To that end, this paper presents a new automated method for calculating the cost of energy loss for building diagnostics. In the proposed method, first, using a hand-held thermal camera, the auditors collect digital and thermal imagery from the buildings under inspection. Then, using a recently proposed method for Energy Performance Augmented Reality (EPAR) modeling, an actual 3D spatio-thermal model is generated and superimposed with a computational fluid dynamics (CFD)-based expected energy performance model. The resulting EPAR model is placed into the method proposed in this paper for cost analysis of the energy loss. Through a new 3D thermal mesh modeling using k-d tree structure and nearest neighborhood searching, performance deviations between these models are automatically calculated. Using a temperature threshold, the areas associated with potential performance problems are detected in the EPAR model and are visualized using a metaphor based on traffic light colors. Then, the actual R-values of the detected areas are measured at the level of 3D points. Based on the measured R-values and the estimated air change rate for the detected air leaks, (1) the heat loss or gain caused either by poor insulation or air infiltration/exfiltration and (2) the associated energy costs are automatically calculated. The proposed method is validated on several locations of existing residential buildings. The preliminary results show the potential of the proposed method for minimizing the inspection time as well as the risk associated with the cost analysis of retrofitting potential building performance problems.

Aug 1, 2013

By P. J. van Staden

Several differences exist between the columns used for laboratory simulations of heap leaching and commercial heaps. Column walls support part of the weight of the ore and restrict the particle packing arrangements. Columns are typically of a diameter that is smaller than the dripper spacing to be used on the commercial heaps. The stacking practices that cause segregation and stratification on heaps are absent from columns. Intuitively, these physical differences would be expected to be the reasons behind the observed differences between column and heap leaching performance. But how can they be quantified, and what is the magnitude of the differences? Could some of these differences be built into column leaching experiments in order to better simulate commercial-scale heap leaching performance to ease the scale-up calculations from column leaching data? Alternatively, could heap construction practices be improved so that the ideal performance obtained in columns could be emulated on heaps? Data from a few heap leaching cases studies that permit direct comparisons between column and heap leaching performance is analysed, to reveal the extent of the differences in resistance to mass transfer. Discussion is provided on the implications for column and heap leaching practice, and for scale-up design procedures. INTRODUCTION Differences have been known to exist between leaching performance observed in laboratory columns and that of commercial-scale heaps. Both the heap leaching kinetics and finally achievable extent of extraction are generally found to be inferior in heaps compared to that achieved in columns. Heap leaching design engineers extrapolate the anticipated heap leaching performance by multiplying the time-axis of a column-leaching curve by a factor of about 2 and the extraction-axis by a factor of about 0.8, as explained by Jansen and Taylor (2002), Scheffel (2002), John (2011) and Scheffel, Guzmán, and Dreier (2016). The procedure is illustrated in Figure 1 by means of a hypothetical example. The solid line represents the leaching performance observed in a laboratory column, and the dashed line represents the anticipated leaching performance of a heap, extrapolated from the column leaching data using these empirical scale-up factors.

Jan 1, 2019

By F. Parada Luna, F. Parada Torres, J. Salvo, A. Reghezza

In the pyrometallurgical processes of copper concentrates, arsenic is preferentially concentrated in the dusts carried by the gases as a result of their volatility and subsequent condensation in the gas cleaning train. In this work results obtained by alkaline leaching of the dusts from Ministro Hales roasting plant, belonging to Codelco, are presented. For the Ministro Hales plant the alkaline leaching would be an alternative to the recirculation of dusts to the roasting furnace. The experimental study considered NaOH and NaOH plus NaHS leaching of two samples of dusts, with 4.24 and 2.55% arsenic respectively. The results show that it is feasible to extract 90% of the arsenic and 50% of the antimony at room temperature using only NaOH, and when the temperature increases to 95ºC, the extractions of As and Sb increase. Copper remains in the solid residue with less than 1% dissolution, and the NaOH net consumption was approximately 140 kg/t of dust. In leaching tests with NaOH + NaHS, two types of methods were tested, baking plus leaching with water and direct leaching with a NaOH+NaHS solution. With the second method arsenic extraction increased to 95% and copper dissolution was less than 0.01% at 85ºC, NaOH 100 g/L, NaHS 90 g/L, 1.5 h and L/S ratio of 5/1 (L/kg). The bismuth remains stable in the solid in all cases. INTRODUCTION The presence of arsenic in copper concentrates has increased with time and the environmental regulations are becoming increasingly more stringent. In concentrate treatment pyrometallurgical plants, most of the arsenic is volatilized condensing in the gas train and is collected along with the entrained solids to form the flue dusts. Under these conditions, in smelters of copper concentrates with high arsenic content, the dusts are being treated in hydrometallurgical plants to extract and stabilize the arsenic, which also means that most of the copper contained in the dust is co-extracted with the arsenic. This affects the recovery of copper in the smelter and an alternative such as the selective alkaline leaching of arsenic, would allow the copper from flue dust to be recovered.

Jan 1, 2019

By D. K. Sarkar, Ying Huang

"Superhydrophobic thin films were fabricated on aluminum alloy substrates by chemical etching followed by passivation with organic acid molecules; (ii) electrophoretic deposition (EPD) of functionalized ZnO nanoparticles and (iii) electrodeposition of organic-inorganic composite materials. The physical and compositional analyses of the deposited thin films were characterized by SEM, FTIR, XRD as well as contact angle goniometer. The contact angle and surface roughness of the superhydrophobic surfaces prepared by the chemical etching process were found to be 156° and 2.29 µm, (ii) by the EPD process were found to be 155° and 4.54 µm and (iii) by the electrodeposition process were found to be 159° and 7.11 µm, respectively.The corrosion properties were analyzed with both polarization and electrochemical impedance spectroscopy (EIS) in NaCl aqueous solutions. The results demonstrate that the superhydrophobic thin films on aluminum alloy substrates display better anti-corrosion behavior than the as-received aluminum substrate. The comparison of results pertaining to the compositional and corrosion properties of these thin films on aluminum will be discussed in this work.INTRODUCTIONSuperhydrophobicity is defined as a surface property which provides non-wetting characteristics with a water contact angle larger than 150°. It is observed that the creation of certain micro-nanoroughness structures promotes the entrapment of air in the spaces of the rough surface morphology. In addition, lowering the surface energy helps to reduce the affinity of water drops to the surface, thereby weakening the water-surface interaction. Recently, various fabrication methods for superhydrophobic surfaces have been explored (Sarkar, 2010, Huang, 2010, 2011, 2013, 2015a, 2015b), such as the sol-gel process (Brassard, 2011), plasma treatment (Marchand, 2013), chemical vapor deposition (Zheng, 2009), chemical etching (Saleema, 2011), electrodeposition (Ying, 2011) and electrophoretic deposition (EPD; Huang et al., 2015b)."

Jan 1, 2016

By A. R. Kinkel JR.

"The Buffalo Ankerite mine is in the southern part of the Porcupine gold district of northern Ontario. The mine has a history of exploration and development reaching back to 1911, and has been operated continuously since 1932. From 1932 to 1942 a total of 510,874 oz. gold was produced from the mine. In 1941 the production was 71,654 oz. from 448,621 tons of ore.With few exceptions, the ore-bearing veins did not crop out. They were discovered during the prospecting of the prominent outcrops of barren or low-grade quartz-carbonate breccia near the veins.GEOLOGICAL SETTINGThe Porcupine gold district lies in an area of folded and sheared Precambrian lavas, sediments, and intrusives. The Buffalo Ankerite mine is in the southern part of a large fold. The structure appears to be a continuation of the Vipond cross anticline and accompanying syncline described in earlier papers (1, 2). The orebodies lie along both flanks of the synclinal part of the fold, and are known as the north and south vein systems, respectively. No mineable veins have been found on the axis of the syncline (Fig. 1).The rocks found in the mine area are pillow lava, dacite, conglomerate, quartz porphyry, tuff, and fragmental lava. The tuff and fragmental lava are now largely altered to chlorite schist. Productive veins have been found only in pillow lava, dacite, and conglomerate, but a minor amount of gold occurs in some of the quartz porphyry. The Porcupine Creek fault, a zone of intense shearing over 1,000 feet in width, lies immediately south of the mine. A spur fault branches to the northwest from the Porcupine Creek fault, separating the north from the south vein systems ( Fig. 1) ."

Jan 1, 1954

By J. B. Heslop, D. S. Bubar

"The Gondor Zn-Ag-Pb-Cu deposit is a stratabound massive sulphide lens occurring within Archean volcaniclastic rocks of the Yellowknife Supergroup. The deposit is located in the west-central portion of the Slave Structural Province, approximately 350 km north of Yellowknife.Initial diamond drilling at Gondor has outlined a steeply dipping, L-shaped, folded, massive sulphide body, which may be traced over a strike length of approximately 800 m, and to a depth of 350 m. True widths of up to 40 m have been intersected in the thickest part of the deposit. Preliminary estimates suggest that the deposit contains a minimum of 7.5 million tonnes grading 6% Zn, 50 g/tonne Ag and less than I% combined Cu and Pb. In addition, significant gold, grading up to 2.8 g/tonne, occurs in some parts of the deposit. The mineralization is open both down-dip and along strike.The Gondor deposit lies conformably within a predominantly east-west striking, north-facing sequence of felsic to intermediate volcaniclastic rocks. Coarse fragmental rocks are abundant in the hanging wall, whereas ash and lapilli-tuffs predominate in the footwall. The main structural feature in the area is a large-scale, steeply northeast-plunging, Z-shaped fold. The sulphide mineralization lies within the synformal portion of this fold, with the thickest part of the deposit coinciding with its hinge zone. Several episodes of faulting have also affected the local stratigraphy.The wallrocks of the Gondor deposit were hydrothermally altered prior to the onset of medium-grade regional metamorphism. A halo of altered rocks surrounds the massive sulphide lens, with no apparent difference in the degree of alteration between the hanging wall and footwall strata. The alteration zone is characterized by the addition of MgO and K20 and by the depletion of Na20 and CaO. These changes are reflected in the mineralogy of the altered wallrocks by local enrichment in chlorite, biotite, muscovite and cordierite.The mineralized zone is medium- to coarse-grained, well-banded and is composed largely of pyrite, quartz, and sphalerite with subordinate galena and chalcopyrite. Preliminary studies of metal distribution indicate that a lateral zonation is present, with lead enrichment in the central part of the deposit, and copper enrichment toward both ends. Stringer-type copper mineralization has not yet been discovered in the footwall of the Gondor deposit."

Jan 1, 1985