Search Documents

By Y. Kocaefe, D. Bhattacharyay, D. Kocaefe

The carbon anodes used in the electrolytic production of aluminum are made of petroleum coke, recycled anodes and butts, and coal tar pitch. Due to technological advances in the aluminum production technology, aimed at increasing production and decreasing energy consumption and greenhouse gas emissions, better quality anodes are required. Presently, the anode quality is evaluated by visual inspection and the analysis of a small core taken from 1.5-2% of the anodes produced. The visual inspection is susceptible to human error and limited to surface imperfections. The analysis of cores takes time, and therefore, it is difficult to determine the existence of a problem and intervene at the right time. In addition, the core does not represent the whole anode due to the non-homogeneity of anodes. A validated online anode quality control system can highly improve the situation. In this article, an electrical resistivity measurement method developed for this purpose is presented.

Jan 1, 2014

By James J. Roettger, Robert J. Mitchell

"The results of a series of model stope pours designed to investigate working pressures on bulkheads during hydraulic pouring of classified tailings backfill are reported. Total bulkhead pressures and fill water pressures were monitored under the condition of a fully saturated backfill. Similitude of the model testing is discussed and equations are developed to estimate bulkhead pressures under prototype conditions. The model results show that good base drainage, combined with a bulkhead setback, can reduce the expected bulkhead pressures to values such that timber or concrete block structures should be capable of supporting a saturated backfill. Introduction Bulkheads are used in underground running operations to block drift openings in order that hydraulically placed sand backfill can be contained in stope pours. Whenever possible, the sand fill is designed to have sufficient percolation rate so that excess hydraulic transport water will gravity drain out through the bulk headed drifts. This avoids costly decanting systems. Early bulkhead design assumed that the bulkhead pressure could be as high as 0h = Hy where H is the fill height and ""y is the saturated unit weight of the fill (Thomas et al., 1979)(1). A typical design pressure for a 50 m fill height would be 1250 kPa giving a design force of 12,500 kN on a bulkhead located in a drift of 10m2 in area . Typical bulkheads were 1 m thick heavily reinforced concrete structures formed and poured into a notched drift. Not only were these expensive structures but the associated problems of inside drainage systems and curing time delays increased production costs. As experience with bulkheads for large bulk pours increased and fill pressure measurements became available [see, for examples, Libby et al., 1975(2), Askey et al., 1978(3)] , 'free drainage' timber and concrete block bulkheads were designed. Substantial savings have been realized using these types of bulkheads but greater engineering design and monitoring of backfill pours is necessary to ensure that backfill pressures do not exceed the bulkhead design pressures.The effective and total stress components of fill pressure, the engineering concepts associated with the 'free drainage' design and some detailed design considerations have been discussed by Smith and Mitchell (1982)(4) . It is important to the safe use of these designs, however, that the basic engineering concepts be demonstrated and communicated to those responsible for the day-to-day backfill operations. This paper describes and explains observations from a series of model studies designed to measure bulkhead pressures in a saturated fill."

Jan 1, 1984

By R. A. D. Pattrick, D. A. Polya, D. J. Marsh, J. -J. Bao

"The utility of high-density stream sediment and stream water sampling to the exploration for silver deposits was investigated by the study of the epithermal Ag-Au base-metal prospect at Lagalochan in western Scotland. The geology of Lagalochan is dominated by a calc-alkaline Caledonian intrusive complex emplaced into Dalradian Supergroup rocks (Harris et al., 1988a). The complex consists of subvolcanic porphyrytic rocks associated with intense hydrothermal alteration and brecciation. Early Cu-Ag-Mo-rich mineralization is found in the core of the complex with later Pb-Zn-Ag-Au-As-Sb-rich mineralization toward the margins (op. cit.).Stream sediment sample analysis spatially resolved the Cu-rich and Ag-rich mineralization. Ag and Cu anomalies relative to local background values were found in all size fractions analyzed (-125µm, +125 µm, +180 µm, +250 µm) but the more pronounced anomalies were found in the -125 µm fraction. The coarser fractions generally revealed more erratic but longer dispersion trails. The separation of Cu-rich and Ag-rich mineralization is also apparent in the distribution of relatively high dissolved Cu and Ag in stream waters, particular when expressed relative to the solute load as Cu/TDS and Ag/TDS.The mineralization at Lagalochan is indicated by Ag, Cu and Pb stream sediment and water concentrations that are anomalous with respect to local backgrounds, but are difficult to distinguish from regional backgrounds. This emphasizes the further potential of high-density stream water sampling,in particular, as a viable geochemical exploration tool on a sub-regional scale for epithermal depositsin relatively unpolluted upland terranes."

Jan 1, 1995

By S. Zador

"IntroductionIn the past decade, metallurgical and mining companies have shown an increased interest in the licensing of technology. When licensing technology, it is usually to the benefit of the parties, to have at least some of the technology to be licensed protected by a patent.This paper is intended to bridge the gap between the engineer in the field of mining, metallurgy and mineral processing who is interested in exploiting an invention commercially, and the patent agent or intellectual property lawyer whom he/she might retain to prepare a patent application and then prosecute the application to obtain a granted patent. It is also intended to encourage the inventor or a small business concern to consider the value of patents in the sale and licensing of technology. The lawyer may subsequently advise and assist the inventor in licensing his/her invention.A brief outline of some of the basic features of the patent system follows. The nature of the information, which the patent professional requires from the inventor to enable him/her to draft a patent application, will also be considered in general terms. Furthermore, various types of licenses which may be drawn up between a licensor of specific technical information and a licensee, will be listed and briefly discussed. No attempt, however, will be made to give a comprehensive and detailed account of the above aspects; the interested reader should consult legal publication and reference books, and patent professionals for further specific information.A granted patent is a document which describes an invention and how to practise it. The claims of the granted patent, figuratively speaking, fence off the intellectual property the inventor regards as his invention. The Commissioner of Patents, representing the Government, grants to the inventor or his assignee the exclusive right of making, constructing and using the invention, and selling it to others to be used, for a limited period of time, in exchange for disclosing the invention to the public. Thus, a patent prevents others from practising the claimed invention but it does not, necessarily, bestow the right to the patentee to practise his own invention. The term of a patent now in Canada and in most of the developed countries of the world, is 20 years from the date of filing the patent application. In the United States the patent term is still 17 years from the date of issuance of the patent. In Canada, the term was changed to 20 years in the new Canadian Patent Act which came into force on October 2, 1989. Any patent application filed prior to that date or granted before it, retains a 17 year life, commencing at the time of grant."

Jan 1, 1991

By K. Enns, J. J. Byerley

"While thiocyanate (SCN-) is used in a number of industrial processes (production of polyacrylonitrile filaments, synthesis of agricultural chemicals and certain metallurgical solvent extraction and flotation circuits) it is recognized more as an undesirable by-product associated with ' the metallurgical industry. Thiocyanate is present at low concentrations in some waste streams from the iron and steel industry. Of particular significance is the formation of thiocyanate during cyanidation of gold and silver ores, concentrates, tailing s and residues. The thiocyanate levels present in the resulting effluents may range from a few mg/I to several thousand mg/I.At present, thiocyanate does not appear to be as hazardous in the environment as cyanide (CN-) at the same concentration although its interaction with other species and resulting decomposition of products may be unacceptable. Of course the presence of thiocyanate in the leaching circuit and ultimately in the effluent streams may add considerably to the oxidative requirments of any non-selective treatment process for cyanidation wastes.With respect to the thiocyanate as it relates to the cyanidation process, two aspects are evident. Thiocyanate forms and persists in the cyanidation circuit resulting in a ""fouling"" condition with subsequent loss of leaching activity. In order to reduce or control this problem, it is common practice for some mills to discharge daily as much as 20% of the barren leach liquor. Besides contributing to fouling of the leach liquor the formation of thiocyanate represents an irreversible loss of reagent cyanide. It is noteworthy that in some present or proposed mill practice reagent cyanide loss through thiocyanate formation may reach 50%(1). The purpose of this paper is to discus s the application of controlled electrooxidation of thiocyanate with the view of suggesting a process for regenerating cyanide from waste thiocyanate(2). The paper describes the important theoretical aspects and presents experimental data obtained for thiocyanate electrooxidation using both small and large scale electrochemical reactors. Some economic conclusions are presented."

Jan 1, 1984

By Bertrand Wolfman, William E. Stanley

"This paper reviews the traditional mine accounting systems, including ""custodial accounting"" and unit costing, and then suggests that the use of flexible budgets represents a more suitable method of reporting costs in order to assist the mine manager in improving productivity. Examples of various applications are given to show that the result is a clear reporting structure.Custodial Accounting is Emphasized in Traditional SystemsTraditional mine accounting has been mainly concerned with the accuracy of financial reporting to ""head office"" for the use of the directors and the company's bankers and shareholders. This is often called custodial accounting and it represented the main purpose of accounting when first developed in Europe hundreds of years ago. This important development permitted the establishment of enterprises which were separated from their owners because they could rely on accurate financial reports of management's stewardship.As custodial accounting is fairly broad and historical in nature, it is often not very useful to the mine manager for ongoing monitoring of performance of mining, milling, maintenance, and other support and staff groups. In spite of the considerable investment in accounting staff and computer support, many accounting systems have not been upgraded so that they accurately reflect workplace performance on a weekly or monthly basis.Budgets are Often FixedMany mines today also still emphasize fixed budgets. Thus, the mine plan which is set in the fall of one year is converted to a monthly tonnage and detailed dollar budget for periods of up to sixteen months in the future. The only certainty in this plan is that actual events will differ; timing, mix of mining methods and production volumes will differ on a monthly basis.Unfortunately, the fixed budget has no capability to reflect these operational changes. It is frozen for the full year. The result is that actual results will inevitably be compared to an outdated target."

Jan 1, 1982

By Stavros A. Argyropoulos, Radhakrishna Valiveti, Bernard Closset

"The use of microprocessors in metallurgy is currently increasing at a very fast rate. A large number of companies are offering systems ""off the shelf"" which are aimed at the data acquisition and process control market. There are two main drawbacks to these systems: first, they are usually quite expensive, and second, they are not completely compatible with the target metallurgical application. An alternative is to develop a microcomputer-based system "" in lab "".A dedicated microcomputer system has proved to be very useful in many metallurgical research applications(1,2)). However, in this system the analog input signals had to be transferred over long distances , and significant noise was introduced despite the use of shielded cables. In order to overcome this problem a network of low pass-filter s was designed and built. The usage of the abovementioned system brought the need to digitize the analog signals in-situ and transfer the digital signals, which are much less susceptible to noise over very long distances. This distinctly different design philosophy has become a reality with the evolution of microprocessor technology over the last few years. This design philosophy is utilized in this development."

Jan 1, 1984

By R. W. Thompkins

"PREFACEThis paper will be published in three parts. Part 1, in this issue, will cover the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.Part 2, to appear in the October issue, will deal with radiation theory applied to uranium ores, other radon migration factors , fact ors affecting the radon gas release rate, measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade, and estimating radioactivity from grade analysis.The series will conclude with Part 3, in the November issue, which will discuss the techniques for controlling radiation and give some example calculations.1.0. Occurrence of Uranium1.0.1. Uranium is widely distributed in nature. Sedimentary rocks contain less than igneous or metamorphic rock s and as the outer 10 miles of the earth's crust is composed of 95 per cent igneous and 5 per cent sedimentary rock, it has been estimated that about 1.3 x 1014 tons of uranium exist in the earth's crust.1.0.2. It is not surprising, therefore, that radiation has existed naturally in the ear h ever since the beginning of time. It is found in such places as:(1) non-uranium mines;(2) houses not close to or connected to uranium mines;(3) ground-water tables supplying drinking water to large populations.1.0.3. All mines do not necessarily have abnormal radiation in them, but it is possible for many mines to have abnormal levels of radiation. Therefore, all underground mining operations should be tested for radiation."

Jan 1, 1982

By M. K. Abel

"The Strathcona Mine is located in Levack Township on the North Range ofthe Sudbury Basin. The main orebody consists of pyrrhotite-pentlandite-chalcopyrite mineralization associated with an embayment of the footwall of the Sudbury Irruptive. A zone of massive chalcopyrite-cubanite-pentlandite mineralization occurs in a complex vein system in a series of mixed gneisses and breccias in the footwall. Vein widths vary from a few millimetres to 6 metres. In December 1979, this zone was estimated to contain 976,000 metric tonnes, with a grade of 9.31% Cu and 0.46% Ni. The vein system has a general strike of N 68°W at an angle of 60 degrees to the average strike of the footwall contact of the Irruptive. The dip of the vein system is 45 degrees sw. The strike and dip of individual veins in the system coincide with the directions that would result if a compressive stress had acted in a direction normal to the footwall of the Sudbury Irruptive, producing a conjugate set of fractures. The strike of the Irruptive at the Strathcona Mine is parallel to the long axis of the basin.IntroductionThe Strathcona Mine, owned and operated by Falconbridge Nickel Mines Limited, is located in Levack Township on the northwest rim of the Sudbury basin (Fig. I) . It is one of a group of nickel-copper sulphide ore deposits present along an 8.2-km section of the North Range of the Sudbury Irruptive. In the mines of the North Range, subunits of the Irruptive, going from hanging wall to footwall , include felsic norite, dark norite and dark norite breccia. The footwall complex at Strathcona includes the late granite breccia, which hosts a large proportion of the nickel-copper ores, and a compositionally variable group of brecciated and migmatized rocks, herein referred to as the feldspathic gneiss complex. It is within this latter group of rocks that the vein system of the Copper Zone occurs."

Jan 1, 1981

By Robert B. Parsons

"It is easy to throw darts at government - and government often deserves to be a target. This month, Tax Notes examines tax legislation from a different angle, and sees some bright spots.The following article is based on a paper presented by the author at the International Gold Symposium in Rio de Janeiro in August 1989Introduction""No man's life, liberty, or property are safe while the Legislature is in session.”With one federal government, ten provincial governments, and two territorial governments all claiming to have constitutional rights to tax and otherwise regulate Canada's mining industry, and with each of these thirteen governments pursuing their respective rights with some vigor, government involvement in one way or another is an accepted way of life in the industry. While one's initial reaction to government involvement in an industry might be one of scepticism or fear, generally speaking the federal, provincial, and territorial governments in Canada tend to be pro-mining. They recognize the importance of the mining industry to Canada, especially in terms of job creation and exports. It is not surprising, then, to find that an array of valuable fiscal incentives are available to the industry through federal and provincial legislation.This paper summarizes the principal incentives that are inherent in Canada's tax legislation, as well as the Canadian Exploration Incentive Program. Although it is beyond the scope of this paper to deal with all of the incentives that are available, it is noted that various forms of federal or provincial assistance are also available outside of specific legislation, through negotiation with government departments. This latter type of assistance is generally directed toward helping with the cost of infrastructure such as roads or hydro lines, or Jess often toward loan guarantees or similar financing assistance."

Jan 1, 1990

By George R. White

"The Phalen Colliery, the Cape Breton Development Corporation's flagship, is now producing thermal and metallurgical grade coal in Eastern Canada's Sydney Coal Field. The colliery is a drift mine operating under the waters of the Atlantic Ocean. Improved mechanization, including a 2200 tonne per hour cable conveyor, and the introduction of modern retreat longwall mining methods as part of the Phalen concept are now paying off in better productivity and low operating costs. Geological conditions within the coal field are consistent with plans for ever greater outputs in the 1990s. Although much of the current production improvement is related to uprated machine capacity and simplified mines planning there is potential for even further development in the areas of maintenance, process control and engineering. Human resource development will also be a key factor. These programs are now well under way and Phalen Colliery is poised for top results in the 1990s. Comparison of the CBDC's top producer with similar operations elsewhere in the world, quantifies that potential.IntroductionAn exciting new mining project which has recently started production on Canada's East Coast has been conceived and designed to be one of the most modern and productive coal mining operations in North America.As with all mining operations, the business is basically that of material transportation. Daily, the product is transported many kilometres from the underground face to the surface and then to washing facilities. Men, materials and equipment are transported to and from the surface and the operating faces and services, such as electrical power, ventilating air, fresh water, discharge water, communications and compressed air are supplied throughout the operation to cover operating requirements. On all accounts the operation has been designed to take advantage of the latest proven technology."

Jan 1, 1990

By Robert B. Parsons

"The pendulum in Ottawa has swung dramatically from fiscal policy to monetary policy over the last several years. International trends indicate that the pendulum has to start its swing the other way, if Canada's mining industry is to maintain its preeminent position in the global mining arena. This article, which is based on a paper presented by the author at the 37th Annual Meeting of the Newfoundland Branch of CIM, identifies these trends and how they could interact with Canadian policy.IntroductionThe title of this paper is not a very imaginative or catchy one, but it states the topic quite succinctly, if not tersely. This paper looks into a crystal ball to see what might be in store for mine financing over the balance of the current decade.In the event that the reader feels some trepidation about the prospect that such a paper could seek to be the definitive work on the subject, it should be made clear at the outset that this is not the case. The author is, after all, not an economist, a scholar, a financial analyst, or a soothsayer, but is rather a simple accountant who has been closely involved with the mining industry, and the financing thereof, for some twenty years.The paper recognizes that, while a mine may be born when production begins, the mine is conceived when exploration starts. As this act of conception is obviously an essential part of mining, the financing of exploration is also covered in this paper. To attain a focus, this paper approaches the topic of mine financing in the nineties as follows: first, the major emerging forces in the industry are identified: and, second, the implications of each of these forces on financing are considered."

Jan 1, 1991

By Collin Bartlett, H. Storch

"Modern metallurgical processes operating with oxygen enriched air, such as the Outotec Flash Smelter and Flash Converter, generate very concentrated SO2 off-gas, which in combination with Outotec sulphuric acid plant technology allows the production of high pressure steam to be used for power generation. Outotec combines well proven technology of sulphur burning plants for this purpose with metallurgical plants.The application of Outotec’s proven LURECTM process enables processing of SO2 gas of up to 25 vol.-%. This process maximizes the energy recovery from the SO2 oxidation at a suitable high temperature level which can be turned into high pressure steam. The application of the Outotec HEROSTM heat recovery system enables the generation of low pressure steam from the absorption energy released at the intermediate absorption step. Additionally, energy is also recovered in the acid coolers for boiler feedwater pre-heating.The concept of integration of high and low pressure steam in combination with the pressurized operation of the boiler feedwater deaerator, thus heating up the boiler feed water to temperatures around 160…170°C, enables indirect transfer of low pressure steam (for deaerator operation) into more valuable high pressure steam, which improves the degree of heat recovery. This is the characteristic of Outotec’s HEROS+TM process.The increased generation of high pressure steam will in turn enable the generation of more electricity when compared to a standard traditional sulphuric acid process."

Jan 1, 2014

By Debasis Deb, Ankur Narang, G. P. Raja Sekhar, Kamal C. Das

"The stability of underground structures made (especially) in jointed rock mass is of the utmost important to designers, engineers and operators. Rock bolting is generally being practised to reinforce excavation walls and roofs by minimizing the movement of rock joints. This study proposes a new analytical model for the prediction of displacements, axial load and shear stress of a fully grouted rock bolt intersected by single or multiple rock joint(s). The governing equations for rock bolt are derived based on the assumption that shear force generated by slippage along the bolt-grout interface has a linear relationship with respect to the relative displacement at the interface. The proposed model is novel compared to the existing literature in the sense that it accounts for rock kinematics as an enriched sum of a continuous part (elastic) and a discontunous (jump) part due to the presence of joint planes. The complete solution of the bolt displacement, axial load and shear stress is derived as a function of the rock displacements, and, it comprises of Heaviside and/or Dirac delta functions in the solution space due to the jump at the intersection point(s) of bolt(s) and joint(s).Our novel solution is able to predict the elastic behavior of a grouted bolt, subjected to opening of the joint planes in pull-out test and also in excavated tunnel. These two cases also serve as benchmarks for grouted rock bolts with multiple joints and can be used for validation of numerical and experimental models. Further, the solution is applied to analyze the behaviour of grouted rock bolt as well as cable bolt installed in circular tunnel, with variations in rock joint(s) opening displacement, shear stiffness in the boltgrout interface and locations of the joint planes. Results indicate that for a specified grout stiffness, the maximum axial load developed in the bolt for discontinuous distribution of rock mass displacement is significantly higher than that of the continuous distribution of rock displacement. This paper provides an analytical interpretation of bolt beaviour considering multiple joint planes with variable joint opening displacements. The results obtained via the analytical method are in line with the corresponding investigation done by other authors. Thus, our analytical treatment can be used to understand bolt behaviour in realistic situations."

Jan 1, 2015

By Robert E. McIvor

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency also has been used extensively by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which is appended hereto. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided.Comminution is responsible for a major portion of mineral processing plant energy consumption and operating costs. Bond Work Index efficiency provides valuable means, first, for benchmarking one’s plant performance against others in the broad industry, and hence defining the extent of the opportunity for improvement. Secondly, improvements in circuit efficiency with implemented changes can be quantified and monitored as part of continuous improvement efforts. These two important business activities are thus facilitated, and, in the absence of any other accepted method, otherwise would be lacking without the existence and application of this standard for comparison. While often loosely applied in the past by plant metallurgical staffs, the increased precision offered by this guideline provides much clearer definition of both the conceptual and statistical meaning of these measurements. Even a small improvement can be enormously financially important, but only if differentiated by measurement. This guideline was thus intended to provide industry improved means to differentiate comminution circuit efficiencies. Carbon footprint reduction is coincidental, but nevertheless can be substantial.The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies."

Jan 1, 2016

By N. E. Chaouai, M. Lavigne

"Indicator kriging is one of the non-parametric geostatistical techniques, ideal for estimating the reserves of irregular mineralizations (e.g. gold, uranium, platinum, diamonds, etc.). Such mineralizations are characterized by variograms which are very sensitive to extreme values (outliers) and very difficult to model.The classical approach to this problem in the industry is to trim off these high grades using arbitrary empirical upper limits established either from practice or subjectively. Contrary to this simplistic approach, indicator kriging discretizes the histogram of the grades (usually log normal) in several classes and carries out interpolation separately for each class. This paper gives an overview of the differences between ordinary and indicator kriging along with the steps required to carry out indicator kriging. The paper concludes with a case study involving a gold deposit estimation.IntroductionParametric geostatistics (ordinary kriging) has given us satisfactory results over the years in estimating the reserves of well behaved deposits with coefficients of variation close to 1 (e.g. sedimentary and porphyry type deposits). However, numerous problems have been encountered in estimating irregular mineralizations (e.g. small vein deposits of precious metals) with high coefficients of variation in the range of 2 to 5. Such deposits are characterized by a very small proportion of extreme values (outliers) which create distortions on the variograms (pure nugget effect) and render them useless(1,2).The solution often followed by the mining industry today is to trim off these values based on empirical limits. These limits are derived either by comparison with production results (or bulk samples) or by geological interpretations. Needless to say that such manipulations can lead to serious errors in estimating ore reserves (usually underestimation of total metal quantity), especially when production results or bulk samples are absent.On the other hand, the solution followed by the geostatisticians in the past was to smooth out the data using transforms (e.g. normal-score or natural logarithms). Such transforms are nonlinear and they required non-linear estimation techniques such as disjunctive kriging (DK) or multivariate gaussian kriging (MG) which require normal related hypotheses, not necessarily true in geology.Nonparametric geostatistics (indicator and probability kriging) have been -developed in order to handle these problems related to highly skewed distributions."

Jan 1, 1990

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By J. W. McCammon

CRANGES in construction ideas and the continually rising costs of labour and conventional building materials, particularly since World War II, have prompted widespread investigations into the development and adaptation of new materials to meet the new requirements and to help reduce costs. Lightweight aggregates have been prominent in these investigations. The lightweight aggregates most commonly used today are foamed slag, cinders, pumice, diatomite, exfoliated vermiculite, expanded perlite, and bloated clay or shah. Lightweight aggregates contribute to the building industry in several ways: ( 1) in large structures the reduction in deadweight effected by the use of lightweight materials reduces the amount of reinforcing and structural steel necessary to support the structure; ( 2) the decrease in weight of lightweight blocks makes handling easier and faster; (3) pre-fabricated floor and roof slabs and tilt-up walls of lightweight concrete have become feasible and popular; ( 4) lightweight aggregate concrete has good nailability and is easily channelled; (5) concrete and plaster made with lightweight aggregate have good heat and sound insulation properties.

Jan 1, 1957

By W. L. Brown

"The properties of Base Metal Mining Corporation are in Yoho Park about 2 1/2 miles northeast of Field; British Columbia; on the main line of the Canadian Pacific railway. There are actually two mines; the Monarch on mount Stephen and the Kicking Horse on mount Field; separated by the steep valley of Kicking Horse river. The outcrops of the orebodies range from 4; 900 feet to 5; 300 feet above sea-level. The concentrator is situated below the Monarch mine and is connected to the main portal by an aerial tramway. The ore from the Kicking Horse mine is conveyed by aerial tramway to a storage bin on the main highway and is then trucked to the concentrator.During the construction of the Canadian Pacific railway through Kicking Horse valley, galena float was found at the base of mount Stephen. The East Monarch outcrop was staked in 1894. The outcrop of the West Monarch ore body on the cliff face of mount Stephen was not discovered until 1916. The Kicking Horse orebodies on mount Field were discovered a few years later. In 1912, a 75-ton concentrator was erected, which operated at intervals until 1924. During this period approximately 42,000 tons were mined and milled, largely from the East Monarch orebody. In 1928, the Base Metal Mining Corporation, Limited, was formed to take over the Monarch and Kicking Horse mines. A 300-ton differential flotation concentrator was erected and production started in the autumn of 1929. In a very short time, however, the low price of metals forced the mill to shut down until August 1933. From 1929 to 1935, when the mill again ceased operation, a total of 256,500 dry tons of ore, averaging 1.59 oz. silver per ton, 9.7 per cent lead, and 12.6 per cent zinc, was mined and milled, largely from the West Monarch orebody. After a period of further underground development, the concentrator reopened in 1940 and is still in operation. From 1940 to the end of 1944, 354,363 tons of ore was milled, averaging 5.32 per cent lead and 10.47 per cent zinc."

Jan 1, 1954

By R. H. McCorkell

Radon emanation rates. J. and compositions of materials from the Canadian Certified Reference Materials Project (CCRMP) indicate that the fraction of the Rn produced that escapes, E, is usually 1% to 8% and the 238U decay chain is nearly in secular equilibrium. For some Chinese ore standards, E values are higher than f or the CCRMP materials. Standard ore tailings have 2/oPb concentrations higher than expected from their 226Ra concentrations and Rn escape rates (12 - 34%) . Biological materials have E ˜100%, their ash E ˜0%. Pelletizing ore powders at 20 000 lb/in2 reduces J by only 20 - 40% but only 2% of Rn escapes from pressed Li2B4O7 pellets and 0.01 - 0.04% from fused Na2B4O7 or Li2B4O7 discs. Large, difficult-to-explain random variations in J are observed in some situations but several highly reproducible ways of measuring emanation rates have been found.

Jan 1, 1986