Search Documents

By M. Kataoka, Y. Obara

It is known that compressive strength and tensile strength of rocks vary significantly with specimen size. Rocks are composed of crystals and grains in a fabric that includes flaws such as microcracks, grain boundaries and pores. As the likelihood of including severer flaws becomes greater for a larger specimen, the strengths are small. On the other hand, the size effect in the fracture toughness of rocks has not been made clear until now because there are few studies focused on it. In this paper, Semi- Circular Bend (SCB) test was performed using Kimachi sandstone with various specimen sizes. A shape of the specimen is a semi-circular disc with an artificial notch. The specimens were prepared with various thickness t and radius r as the following two groups; t was changed from 10 to 37.5 mm with r = 37.5 mm in the specimen of group (a), and r was changed from 12.5 to 150 mm with t/r = 0.8 in the specimen of group (b). As a result, there was no significant change in the fracture toughness with different t. On the other hand, the fracture toughness increased with increasing r and converged on a certain constant value in a range larger than approximately 70 mm of r. Consequently it was clear that the size effect in the fracture toughness of the sandstone exists.

Jan 1, 2015

This paper describes results of an investigation of fracture during tube expansion of 5052 and 5754 aluminum seam-welded tubes to optimize the forming of aluminum tubes during hydroforming. The tubes were produced in laboratory by press forming of tubular blanks and pilot-scale high frequency induction welding. The effect of property mismatch between the weld and base metal has been investigated. The material work-hardening was obtained by roll forming of sheet blanks in the 0-temper and H32 temper condition. The results showed that a significant work-hardening can be present in aluminum tube without causing weld fracture during tube expansion. The work-hardening increases the yield-strength mismatch between base metal and weld. Annealing reduces the hardness of base metal leading to more uniform deformation during tube expansion. As a result the occurrence of weld fracture is reduced. The study showed significant deformation of the welds during tube expansion. Weld thinning can be as large as parent-material thinning before fracture. To avoid fracture at the weld joint, good formability and high yield strength of the weld is needed. FEM simulation showed that minimizing the width of the weld joint can reduce thinning of the weld.

Jan 1, 2004

By A. Karzhau, B. Aldamzharov, Y. Tussupbekov

"This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of the mine 24 hours a day. The mine auxiliary ventilation has been designed with the maximum length of ducting systems with extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal. The mine needs additional investments for re-designing ventilation network and therefore needs to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation network optimisation processes at the operational metal mine in Kazakhstan. Mine ventilation surveys were undertaken for validation of the computerised ventilation model. The mine ventilation network modelling has been undertaken to be compliant with Kazakhstan mining regulations. Results of the mine ventilation optimisation processes were analysed in terms of financial risks for investments into reconstruction of the ventilation shafts, extension of the ventilation network, variable speed fans and automated regulators. Savings were resulted from improving ventilation system efficiency by reduce airflow in areas without mining activity and redistributing existing ventilation capacity. Based on savings derived from the optimised ventilation network an additional NPV has been received. Stochastic modelling use Monte Carlo simulation producing representation of possible outcomes for the additional NPV considering electricity pricing as a major variability. As result probability distribution for the optimised ventilation network demonstrates the additional NPV in a range of 1.6 - 2.2 million US$ in the corresponding defined value of 90%. Moreover, there is only 5% chance that the additional NPV to be less than 1.5 million US$. Conducted risk analysis for ventilation network optimisation processes gives considerations on volume of investments into the mine ventilation system.INTRODUCTIONCosts for mine ventilation are typically increasing when mines expand to deep levels. Some underground mines in Kazakhstan still use continuously operating fans at its maximum capacity. This is not helping to save energy and costs that are in many cases very significant. This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of a mine 24 hours a day. The mine auxiliary ventilation has been designed with maximum length of ducting systems and extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal from the mine workings (Sabanov, 2019). The mine needs additional investments for re-designing ventilation networks and therefore need to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation networks optimisation processes at the operational mine in Kazakhstan. Mine ventilation surveys for validation of the computerised ventilation model have been undertaken"

Jan 1, 2019

By R. Loj

Katowice Coal Holding (KHW) is one of the largest coal companies in Europe. The company owns five coal mines with a daily output of around 60 000 tons of coal. In the Katowice city area, very good quality steam coal is extracted. The depth of mining varies between 400 and 1100 m and some of the mines rank amongst those most afflicted by methane in the Upper Silesian Coal Basin, with the methane hazard having a significant impact on production and safety. ?Myslowice-Wesola? mine, being a part of the Katowice Coal Holding is characterized by high methane and rockburst hazards. The mine is equipped with a modern surface drainage pumping station. At the mentioned mine, longwall 514 was selected for analysis of its methane emission. The longwall was extracting the thick seam 501 (over 4 m), at a depth of over 900 m, which was subject to high stress and high gas concentration conditions. At a distance of about 50 m above, seam 501 is covered by thin seam 416. The strata between these two seams are sandstone and mudstone layers. In the floor of seam 501, with a thin shale interlayer, is located seam 510, which is the thickest (over 10m) and richest coal seam in the Upper Silesian Coal Basin. In longwall 514 and it?s vicinity, methane was the dominant risk. For this longwall three methods of classical gas drainage were carried out. At first, drainage was undertaken using long boreholes from a cross-cut at level 665 m, located far from the production panel. Later, it was performed using typical boreholes drilled from the ventilation gallery (tail gate road). Finally, it was undertaken using a degassing drift executed in the upper coal seam 416. All of these headings, ie. cross-cut level 665 m, the ventilation road and conveyor road in seam 501 and the degassing drift in seam 416, were equipped with media for drilling and proper drainage pipelines. Due to the high rockburst hazard and some problems with caving, several kinds of de-stressing and torpedo blasts were carried out in both coal seams and roof rocks. The subsequent analysis and experiments allowed the establishment of some general rules for carrying out degassing operations effectively. The effectiveness of a degassing drift was demonstrated. In some instances, the system allowed more than 70% of the total methane released to be captured and fed into pipelines. The aforementioned blasts had a marginal impact on methane emissions and the efficiency of degassing methods. Cyclic drilling and regular switching of boreholes in phase with the mining progress and working face advance were shown to be essential.

Aug 1, 2013

By D. Kulchyski, R. Thibault, D. Lamoureux

"Mine tunneling applications are sensitive to the leakage and friction performance of ducting systems. Improvements in performance can help project economics through reduction in drift height, booster fan spacing, fan electrical power requirement, and deferral of ventilation raise construction. Semirigid plastic ducting has enjoyed significant adoption in mine tunneling in recent years. This paper explores technical properties and performance aspects of this relatively new material application.INTRODUCTIONUnderground mining projects are sensitive to mine development cost and schedule to meet first production—both of which are defined to a substantial extent by mine access construction. The very nature of mine access development requires driving accesses into new areas and even mechanized and automated tunneling methods require ventilation. Until underground airways are connected, allowing a flow-through circuit, ducted ventilation is required to establish ventilation within any single-access (i.e.: dead-end) heading. See Figure 1 as an example of ducted ventilation. Improving performance of ducted ventilation systems impacts project cost and schedule in several ways:For drifts whose height is defined by overhead clearance above haul trucks or tall equipment, smaller diameter ducting will decrease heading size.With higher ventilation flows, activities can be less ventilation-constricted; secondary headings can be worked without restriction, which improves schedule.Given the ability to provide more air for a given fan power, blasting gasses can clear the face and mine more quickly so crews can return to work more quickly - allowing higher advance rates.Lower electrical costs – both due to lower power consumed by fans and with the requirement for fewer electrical stations to power booster fans."

Jan 1, 2019

By M. Alvarez-Silva, A. Uribe-Salas, J. A. Finch, M. Mimezami

The point of zero charge (PZC) of electrokinetically anisotropic minerals (chlorite and serpentine) was determined using the Mular-Roberts (M-R) titration technique, and compared to isoelectric point (IEP) obtained from electrophoretic mobility measurements. To validate the M-R technique, the point of zero charge and isoelectric point of two isotropic minerals (alumina and silica) were shown to be comparable. For serpentine and chlorite, respectively the PZC was found at pH 4.3 and 4.6, while the IEP occurred at pH 3.2 and <3. Settling tests showed that the maximum settling rate, which corresponds to aggregated particles, for chlorite was around pH 3, i.e., close to the IEP; lizardite did not show a conclusive maximum.

Jan 1, 2009

By D. Adiguzel

In this research, providing the sustainability of production quality was aimed for a quarry which is located in Istanbul western part of Turkey and producing concrete aggregates with different types of rock. First, research field was divided in 3 different areas in accordance with the geological differences and parameters that control their product quality, limit values of standards and effect levels were determined. Concrete aggregate conformity tests which are stated in international standards were applied on samples which were taken from these 3 different areas and physical, geometric and chemical properties of each rock type were revealed. The properties of the 3 different types of rock which were produced in the quary were determined and the binary blends were composed. Blending studies were conducted with linear programming technique. In the linear programming model, the cost of aggregate production was aimed to be minimal. The limit values that meet literature and national standards for usability of aggregates in concrete were defined as constraints in the linear programming model and evaluated with objective functions, thus the most suitable aggregate blends were composed. In conclusion, to provide the sustainability of product quality, the most appropriate product blends were composed for the research field and the usability of this model for those quarries were revealed.

Aug 1, 2013

By Donald F. MacDonald

METAL PRICES RISE WITHIN the past nine months, the mining industry of the world has been revivified by a spectacular price advance for the metals. ln fact, practically all geological raw materials have been marked up during this period. Reviving industry started the price rise, but the armaments race among the nations has intensified it. These factors, coupled with our decided building shortage, which must be made up, will probably maintain metal prices at decidedly favourable levels over the next two or three years, or longer. OUR MINERAL CIVILIZATION It is interesting to recall that in the past hundred years, while the white population of the world increased some three ta three and a half fold, the consumption of minerals increased seventy-five fold. In other words, ours is a mineral civilization. If we disregard short slumps, which we will occasionally experience, it seems certain that the bread upward trend in mineral consumption will be maintained for many decades into the future. Nations without reasonably abundant and diverse mineral deposits will eventually become nations without much power. Canada is blessed with a splendid store of minerals. Its mineral industry is now facing an exceptionally rosy future. What of the mineral industry of Nova Scotia? GEOLOGICAL RESEARCH ALLOWED TO LAG RN NOVA SCONA Many years ago, when geological science was in? its infancy, much geological study was carried on in Nova Scotia. In 1827, Francis Alger began work on the iron ores in the Bay of Fundy region. In 1886, E. R. Faribault began his series of remarkable papers on Nova Scotia geology. Between these dates, many others published papers on the geology of the Province. The most outstanding of this early group of geologists was Sir William Dawson, whose published works on Nova Scotian geology extended over the period from 1845 to 1891.

Jan 1, 1937

The rate of liquid copper deoxidation during top blowing of reducing flames has been investigated using a high capacity thermogravimetric unit at 1200 °C. For 1 kg copper samples, it was observed that the rate of deoxidation was proportional to the flow rate of the reducing reagent (H2 or CO). Under similar experimental conditions, it was found that H2 is more effective than CO even though both have similar thermodynamic potential to deoxidize liquid copper. The rate of deoxidation of liquid copper with reducing 0 2/CH4 flames was measured for 0 2/CH4 molar ratios of 1.5 to 2. The deoxidation rate depends on the 0 2/CH4 ratio and decreases as it approaches the stoichiometric ratio (02/CH4 = 2). Estimation of the rate of deoxidation of liquid copper with top blowing flames based on the thermodynamic composition ofH2 and CO in the product gases, agrees well with measured values.

Jan 1, 2007

By Gregory C. More O'Ferrall

Generally pillars in the Southern African hard rock tabular underground mining environment are designed using either empirical pillar design formulae or numerical modelling (analytical) methods utilizing the Hoek-Brown failure criterion. However, none of the pillar design methodologies employed takes cognizance of weak layers either within the pillar material or in the immediate foundation of the pillar. Over the past few years, the presence of a weak layer either within the pillar material or within the immediate foundation of the pillar has resulted in the closure of one platinum mine (Everest Mine), closure of one chrome mine (Wonderkop Chrome) and large-scale instability in a couple of chrome and platinum mines in South Africa and Zimbabwe. A study has been initiated to better understand the failure mode and strengths of the pillars where pillar failure associated with weak layers occurred. Owing to the infancy of the study into the failed pillar strength and failure mechanism, the purpose of this paper is to highlight the circumstances that led to the collapse of mining sections and a shaft, and the difficulty associated with designing pillars in the Southern African chrome and platinum mining operations.

Jun 1, 2012

By Zhang. L.

Ordered intermetallic PtSb had been synthesized by arc-melted and then sintering treatment. The electro-oxidation of formic acid on PtSb was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results are compared to those at a polycrystalline platinum electrode surface. It was found that PtSb intermetallic was catalytically more active than pure platinum according to the onset potential and current density. XRD and XPS technologies had been used to investigate the crystal structure and electron effect. We think formic acid decomposition on PtSb favors the reactive intermediate route and is not very much affected by the CO intermediate as compared to Pt.

Jan 1, 2005

By M. N. Vu, G. Armand, A. Noiret, D. Seyedi

Extensive experimental observations have been performed around drifts and shafts at the Meuse Haute-Marne (North-Eastern France) Underground Research Laboratory (URL) to assess the extent and pattern of the induced fracture networks in Callovo-Oxfordian claystone. Two types of fractures can be distinguished, namely; shear (mode II) and extension unloading (mode I) fractures. The main goal of the present paper is to provide insights on the extent of damaged zone around the drifts by numerical simulations. A two-step approach is considered. First, 2D elastic calculations are performed for simulating the excavation of a drift following the direction of the major in situ horizontal stress. The evolution of the stress and strain tensors around drifts are calculated by applying an elliptic convergence function on the drift wall. Two failure criteria are then verified for the induced damage. An equivalent strain and an elastic energy based damage criteria are considered. The obtained results show that the employed simplified approach provides rather good results for the extent of the damaged zone for drifts parallel to major horizontal stress. However, post-processing elastic results leads to overestimating the vertical extent of the damage zone and underestimating its lateral extent, where the in situ stress state is quasi-isotropic in a section of drift. Nevertheless, the obtained results show that an energy based damage criterion could be considered as a potential way for reproducing the extent of the damaged zones if a convergence function can be defined for the drift.

Jan 1, 2015

By Brennan Lang

Why Seal Tunnels? ?Restore groundwater levels to pre-mining conditions. ?Saturate rock mass to reduce acid rock drainage. ?Reduce discharge flow to the environment. ?Reduce or regulate flows to a water treatment plant.

May 1, 2002

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012

? A BARGE WILL BE INSTALLED IN THE BOTTOM OF A COMPLETED PIT. ? THE PROVEN BAUER CUTTER TECHNOLOGY WILL BE INSTALLED ON THE BARGE AND A DEWATERING PLANT WILL BE INSTALLED NEAR THE BASE OF THE PIT RAMP. ? THE WATER LEVEL IN THE PIT WILL BE RAISED BY 20- 40 METRES AND REMAIN CONSTANT OVER DURATION OF MINING. ? THE CUTTER WILL BE LOWERED TO MINE 10 METRE DEEP BENCHES ON A CHECKERBOARD PATTERN TO AN ULTIMATE DEPTH OF 200 METRES. ? THE 5? MINUS CUTTINGS WILL BE PUMPED TO THE DEWATERING PLANT, DEWATERED, AND TRUCKED TO SURFACE.

May 1, 2003

By D. Zagidulin

Short term electrodeposition experiments (up to 80 min.) at two current densities 220 and 275 A/m2 with varying concentrations of thiourea and glue were performed to determine the optimum levels of glue, thiourea and current density for industrial copper electrorefining. White Light Interference Microscopy was used to acquire digital images of the morphology of the electrodeposited copper. Scaling analysis was employed to pa-rameterize the morphological information encoded in the images. The limiting rough¬ness, *, the critical scaling length, Lc, and the aspect ratio, 4*/ Lc, were determined as a function of the deposition time and the amount of organic additives. These parameters were used to calculate the dynamic exponent, B, the roughness exponent, 1/z, and the as¬pect ratio exponent, y, plotted as a function of glue and thiourea concentrations. These 3D plots allowed us to find conditions corresponding to the minimum of B and y, at which the deposited copper is characterized by a small roughness and a dense structure.

Jan 1, 2007

By V. ?. Chanturiya, G. P. Dvoychenkova, ?. Ye. Kovalchuk

"Several mineralogical investigations have revealed the composition of modified kimberlites and the mud generated during treatment of diamonds, which contains up to 50% clay minerals (e.g., talc, talcsaponite, chlorite-saponite, Na-saponite) and X-ray amorphous phase. We investigated the composition of the natural diamond surface in relation to the diagnosed minerals and established the sequence and conditions for mineral formation on the crystal surface under kimberlite processing conditions. This article suggests a method to destroy and further dissolve minerals on the crystal surfaces using water system electrolysis products, which makes it possible to restore the diamond hydrophobic properties. The application of chemically treated water in the foam separation cycle under the conditions of high recovery of diamonds made it possible to increase the content of the factory concentrate by 8.0%.INTRODUCTIONThe high content of the modified minerals in the kimberlite ore results in the formation of hydrophilic slicks on the surface of the crystals which decreases the diamond’s hydrophobic properties and increases the losses thereof in the process of grease and foam separation to 20-30% (Kurenkov, 1957; Chanturiya et al., 1998, 1999, 2005; Duikarev et al., 2000).The previous researches have revealed the fact that the prospective way of solving the problem of intensity of mineral impurities formation on the surface of the crystals and the increase of concentration parameters is reached due to application of physical and chemical stimulation techniques on the solid and liquid pulp (Stricland-Constable, 1971; “Improvement of the technology…”, 2006; Makarskii, Adodin & Tarasova, 2011; Chanturiya, Dvoychenkova & Trofimova, 2012). However, the main task of investigations to stipulate the objective achievement is the studying and justification of the reasons of the diamond surfaces covering by the mineral slicks"

Jan 1, 2016

By Horace Freeman

Introduction This paper is an amplification of the paper presented by the writer at the last (1930) Annual Meeting of the Institute (1), and is somewhat in the nature of a progress report upon the introduction of pyrite into the field of Canadian consumption. The burner installed at the plant of the Canada Power & Paper Corporation, St. Maurice division, has been slightly changed in dimensions and has been put into continuous operation during the past year. As predicted, it has been possible to somewhat increase the steam consumption and at the same time decrease the amount of sulphur remaining in the calcine. The grade of the sulphur-dioxide gas produced has been maintained very steadily at 12 per cent, and sufficient experience has been obtained to determine the renewal cost of continuous operation. The object of this paper now is to encourage the development of pyrite, particularly by-product flotation pyrite, as it is shown that there is a very definite field in Canada for this material and that all the previous objections to the use of pyrite have been overcome, and that the use of the material in practice in paper mills has been developed to such a point that the operation of manufacturing the sulphite cooking-liquor is as simple as, or simpler than, the present style of operation with the use of sulphur.

Jan 1, 1931

By S. Isaac

The networks of interdependencies between elements in building projects, referred to as the project topology, are often complex and difficult for project teams to comprehend. It is hypothesized that a graphbased model of the project topology can be based on existing data in Building Information Models (BIM), facilitating the application of graph-theoretic algorithms to analyze this topology. The objective of this study is to propose an outline for the synthesis of BIM and graph theory. This synthesis is expected to contribute to the development of new tools for representing, managing and analyzing the design of building projects.

Aug 1, 2013

By L. G. Bergh

The experience developing a supervisory control and information systems in a SX pilot plant is presented. The plant is located at the Process Control Laboratory, Santa Maria University, in Chile. In this work, the problem of controlling this process is discussed and related literature is briefly reviewed. Then, an innovative control scheme organized in three levels, local, hydrodynamic, and metallurgical supervisory controls is presented in an architecture including field controllers, PLC, and PC networks. Operating decisions in the metallurgical supervisory control are taken with incomplete information from on-stream analyzers. The control proposed is based on metal and acid concentration predictions of intermediate and exiting streams through the use of dynamic and static models and flow rates and input concentration measurements. Preliminary results are presented. The main objectives are to develop and test intelligent techniques in a hybrid system, and to study measurement and supervisory control problems. It is expected to produce reliable results that will contribute to improve the efficiency of this emerging and important process.

Jan 1, 2007