Search Documents

By R. Matusewicz, A. Kaye

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in non-ferrous applications, including the processing of lead and zinc primary concentrates and secondary (post-consumer) materials. TSL is highly flexible and efficient, and is one of the few technologies which can process primary and secondary feeds, and use varying fuels, to deliver high recoveries and excellent environmental performance. With the recent high value of both lead and zinc, and an escalating awareness of the sustainable use of resources, focus on the processing of secondary feed material sources has surged. Ausmelt Technology has proven to be well suited to the economic recovery of values, with twenty-two (22) Ausmelt furnaces processing lead and zinc bearing feed sources now in operation, under design or construction. This paper describes Ausmelt's progress in the fields of lead and zinc processing, and developments in new processing areas such as EAF dust processing and linking to innovative hydrometallurgical technology. Ausmelt has recently committed to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This project is due for start up in the first quarter of 2008.

Jan 1, 2008

By S. R. Noble, F. R. Harris, E. T. C. Spooner

"The Logtung deposit discovered in 1976, is an example of large tonnage (162 million tonnes), low grade (0.13% WO3 and 0.052% MoS;) W(scheelite)-Mo mineralization related to multiple felsic intrusions. Because mineralization is predominantly fracture-controlled (> 95 %) rather than disseminated, Log tung is not a skarn deposit. Metamorphism of the Logtung country rocks (interbedded calcareous shale and graphitic quartizite) to a series of competent reaction skarns (quartz-diopside-garnet calc-silicate, biotite quartzite and wollastonite-vesuvianite calc-silicate) clearly precedes W-Mo mineralization. Hence mineralization was related to permeability created by hydraulic fracturing and not replacement processes.Logtung shows a theme of several phases of mineralization (4) related to multiple intrusions (>2) which is similar to that of the Climax and Urad-Henderson Mo systems. The earliest quartzmolybdoscheelite vein system, which consists of a typical ""porphyrystyle"" crackle-breccia of thin (0.5 mm to 4 mm) quartz-garnetdiopside- molybdoscheelite veins, is related to a high Si02 (approx. 76%), seriate-porphyritic monzogranite stock (approx. 2 km by 0.5 to 1 km) of Cretaceous age (118 ±2 Ma [2u]; Stewart, 1983). Later quartz-pyrite scheelite (fluorite-KINa-feldspars-molybdenite) veins, with prominent green, hornblende-bearing alteration selvages, and quartz-molybdenite (-pyrite-jluorite-scheelite) veins are related to a quartz-feldspar-spessartine-rich garnet porphyritic felsic dike complex approximately 500 m across. Both intrusive phases have anomalously high Wand Mo concentrations of about 100 ppm and 50 ppm respectively, which Stewart (1983) attributes to a primary enrichment. The final stage of mineralization consists of a prominent 4.5 km by 1 km zone of 1 em to 1 m wide polymetallic sheeted veins centred on the felsic dike complex. The system is zoned from quartz scheelite-molybdenite-pyrite-blue-green beryl-jluoritebismuthinite veins in the core to Pb-Zn-Ag veins with abundant arsenopyrite and minor Sn (approx. 0.1%) in the northeast. The focus of recurrent intrusive and hydrothermal activity was located above a flank or nose of the monzogranite stock.The distribution of WO3 and MoS2 grades within the approximately 750 m (across) by 300m (evaluation depth) mineralized zone is a result of the variable superimposition of the four separate vein systems each with different W:Mo ratios. Well-defined Wand Mo ore, shells such as those at Climax, Henderson and Mt. Emmons did not develop at Logtung. The upper surface of the mineralized zone, as shown by the 0.03% MoS2 contour defines an elongate dome with an apical region approximately coincident with the felsic dike complex. Hydrothermal alteration occurs as well-defined vein selvages, and not as pervasive zones.The Logtung deposit shows many similarities to porphyry Mo deposits in the western Cordillera and may be identified as a porphyry W(scheelite)-Mo deposit, with a W:·Mo ratio of 3.3:1. The principal reasons are: (1) mineralization is spatially associated with porphyritic granitic intrusions and (2) much of the scheelite and molybdenite occurs in typical ""porphyry-style"" vein stockworks"

Jan 1, 1995

By J. R. Rau

While refuge chambers are common place in most underground mining projects, there are different philosophies as to what life support systems are to be considered and how these systems are to be applied. Case studies in the underground mining industry have examples of emergencies where the external compressed air and power supply to the refuge chamber were compromised due to proximity of services to the fire location. In 2005, The Department of Industry and Resources, Western Australia, drafted guidelines that listed specific requirements for refuge chambers which included a secondary life support system that would operate independently of external sources. The objective of this document is to examine what critical life support systems are essential for safe entrapment in the event of an emergency and to examine considerations for their application.

Aug 1, 2013

By Roy S. Celland, K. H. Singh

The introduction of 'post' pillar mining at the Strathcona mine represents a new approach to ground support in cut-and-fill applications. The method has also shown significant economic advantages. It is believed that the development of this concept is one of the few examples where rock mechanics principles have successfully been applied in the development of a stoping method. The paper describes the evolution of this method and contains discussions on the theoretical analysis of the technical, operational and economics aspects of the system. Pillar design procedures and field observations on the practical application of theoretical analysis are also outlined.

Jan 1, 1973

By Megan Becker, Aubrey Mainza, Indigo Research Laboratories, Jenny Wiese, Gaynor Yorath, Lucy Little

Particle shape characterisation has an important role to play in mineral processing, to clarify effects of shape on rheology, equipment wear rates, comminution, classification, sizing and flotation. However in industry, shape characterisation is not routine, and the most commonly used shape descriptor in the field (circularity/ angularity/ sphericity) is not invariant. This study aims to investigate shape measurements for a fine particulate ore sample measured with different analytical devices. Two Automated Scanning Electron Microscopy devices with Energy Dispersive X-ray Spectrometry (FEI QEMSCAN® and Zeiss Mineralogic®), and a camera based image-sizer using dynamic image analysis (Retsch CAMSIZER® XT) were compared. Each device was used to analyse the shape characteristics of specific particles in both a coarse sample (–212/+150 µm) and a fine sample (-53 µm) of UG2 platinum ore. Circularity and Roundness frequency distributions obtained from the three devices were then compared. For selected individual particles, circularity showed higher variability than roundness, and the sample circularity distributions obtained by the three devices were completely different. It is clear that circularity data from different studies relying on different devices should not be compared on an absolute scale. The shape parameter roundness was found to be a more robust descriptor than circularity, and it can give a stronger indication of a particulate sample’s shape characteristics on an absolute scale. However, there were still significant differences in the roundness measurements obtained by the CAMSIZER XT and the two Auto-SEM devices, which was attributed to the dissimilar mechanisms of image capture.

Jan 1, 2016

By R. Cammack

"A fundamental component of the Hoek–Brown empirical rock failure criterion is assessing an appropriate mi constant. In developing their empirical criterion Hoek and Brown normalised triaxial test results by dividing the principal stresses at failure by the uniaxial compressive strength to provide mi values for typical rock types. Experience shows that Hoek triaxial tests for individual lithology types commonly have a large inherent scatter. In addition, tests are often conducted on core from random locations, which although being of one parent rock type, display variations in density as well as minor variations in grain size and alteration.This paper presents experience from projects the authors have been involved in which large sample populations of triaxial and UCS tests on similar rock types were available. Geophysical logging data was also available for some projects. The methods used to estimate the compressive strength for each sample and the effects on normalising the data sets are described. The variability of the data and uncertainties and assumptions involved in the process of assigning a mi value from the normalised data are also discussed."

Jan 1, 2015

By P. C. M. Knops, K. Rijnsburger, R. M. Santos

To overcome the challenges of mineral CO2 sequestration, this work utilizes a unique proprietary Gravity Pressure Vessel (GPV) reactor technology, and focuses on reaction products of high economic value. The GPV provides intense process conditions through hydrostatic pressurization and heat exchange integration that harvests exothermic reaction energy. Here, laboratory-scale tests of the envisioned process was performed in tubular and continuously stirred tank reactor (CSTR) autoclave reactors. The mineral used was Olivine (~Mg1.6Fe2+0.4(SiO4) + ppm Ni/Cr), although asbestos, steel slags and oil shale residues are also under investigation. The effect of several process parameters on reaction extent and product properties was tested: CO2 pressure, temperature, residence time, additives (buffers, lixiviants, chelators, oxidizers), solids loading, and mixing rate. The products (carbonates, amorphous silica and Chromite) were physically separated (based on size, density and magnetic properties), characterized (for chemistry, mineralogy and morphology) and tested in intended applications (e.g. as pozzolanic carbon-negative building material). Economically, it is found that product value is the main driver for mineral carbonation, rather than, or in addition to, the sequestered CO2. The approach of using a GPV and focusing on valuable reaction products could thus make CO2 mineralization a feasible and sustainable hydrometallurgical process.

Jan 1, 2015

By C. Schmidt, M. Kohnk, C. Siemers, J. Kiese

The application of conventional titanium alloys is limited to 550°C due to their poor oxidation resistance. In addition, severe grain growth is observed in single-phase titanium alloys in long-term runs at elevated temperature leading to a degradation of their mechanical properties. In exhaust applications in automotive or aerospace engineering, products are often manufactured by cold-deformation like deep-drawing or rolling which is normally difficult in oxidation-resistant titanium alloys due to the presence of titanium-silicides. Therefore, in the current study, titanium alloys based on CP Titanium Grade 1S (soft grade) were developed showing (1) improved oxidation resistance due to a concerted addition of silicon, iron and niobium, (2) microstructure stability by the precipitation of hafnium-silicides mainly on the grain boundaries and (3) good cold-deformation properties. The industrial production route was developed so that the new class of Ti-Si-Fe-Nb-Hf-alloys is now ready for application in exhaust systems of planes or cars at minimum 800°C.

Jan 1, 2015

By R H. Hallam

The Mattagami mining district encompasses a favour-?able belt of folded Keewatin-type rocks, with intercalated sediments and intrusives of late Keewatin age. This environment has been subjected to periods of basic and acidic intrusion. The orebodies lie within the fold structure and are associated with faulting and shearing of considerable magnitude. The No. 1 orebody contains 60 to 70 per cent massive sulphides. The minerals, in their order of abundance, are generally: pyrite, sphalerite, pyrrhotite, magnetite and chalcopyrite. It is evident that the broad geological structure of the district is amenable to ore deposition. There are two ? prominent linear expressions which comprise this broad structure. Both strike directions lie at the edge of, or are related to, a complex gabbro-anorthosite-peridotite zone. The fact that eleven of the ore zones discovered to date coincide with the broad structure indicates its over-all importance. It is estimated that the production from Mattagami Lake Mines will be in the range of 600 to 700 tons of zinc concentrate and 70 tons of copper concentrate per day.

Jan 1, 1964

By M. Dadvand, G. Kipuros, A. Dadvand

"The ability to codeposit fillers within a nickel matrix has led to the production of a new generation of cermet coatings with properties useful for various applications. Hexagonal boron nitride (hBN) is a ceramic-type particulate matter with thermal conductivity, thermal stability, inertness, and lubricity properties that allow it to be codeposited. In this paper, a method was developed for modifying hBN surfaces to allow them to be uniformly dispersed in water-based solutions such as an electroless nickel plating bath. hBN surface modification improved wear performance of the electroless plated cermet due to enhanced interaction between the particulate and nickel matrix. RÉSUMÉ La capacité à effectuer un dépôt simultané de charges dans une matrice nickel a abouti à la production d’une nouvelle génération de revêtements cermet (une combinaison de céramique et de métal) dotés de propriétés très utiles pour diverses applications. Le nitrure de bore hexagonal (h-BN) est une matière particulaire de type céramique utilisée pour ses excellentes conductivité et stabilité thermiques, son inertie ainsi que son caractère lubrifiant, qui permettent son dépôt simultané. Cet article explore une méthode mise au point pour modifier les surfaces du h-BN de manière à ce qu’elles se répandent uniformément dans des solutions aqueuses telles qu’un bain de dépôt autocatalytique de nickel. La modification des surfaces du h-BN a amélioré la résistance à l’usure du placage autocatalytique du cermet en raison d’une interaction accrue entre la matière particulaire et la matrice nickel.INTRODUCTION Electroless nickel alloy coatings can be used for many applications; however, the need for improved tribological properties such as higher wear resistance and better lubricity has increased interest in incorporating particulates (fillers) into the nickel matrix by codepositing the particulates with nickel during the plating process. The selection of the particulate type depends on the desired properties (Sahoo & Das, 2011; Sudagar, Lian, & Sha, 2013). In terms of tribological applications, electroless nickel-based composites are categorized mainly into lubricating and wear-resistant composite coatings depending on the type of particles incorporated. The electroless nickel-phosphorus (Ni-P) composite coatings are composed of codeposited solid lubricants such as polytetrafluoroethylene (PTFE), graphite, WS2, MoS2, and hexagonal boron nitride (hBN) and, compared to nanocomposite electroless Ni-P coatings, they demonstrate a lower coefficient of friction. On the other hand, the nickel-phosphorus wear-resistant composite coatings are composed of hard particles such as silicon carbide (SiC), aluminum oxide (Al2O3), boron carbide (B4C), silicon nitride (Si3N4), diamond, tungsten carbide (WC), and zirconium oxide (ZrO2) and, compared to nanocomposite electroless Ni-P coatings, they have higher hardness and better wear resistance (Sahoo & Das, 2011; Sudagar et al., 2013; Parucker, Klein, Binder, Ristow, & Binder, 2014; Chakarova, Georgieva, Petrova, Dobreva, & Stoychev, 2016)."

Jan 1, 2018

By J R. O Walli

Large production shafts can be successfully sunk through the ubiquitous Blairmore formation of southern Saskatchewan by employing the freezing process and by the installation of a cast iron tubbing lining. Although the freezing technique for shaft sinking and the use of cast iron tubbing to preserve the shaft are new to the North American continent, these procedures have been employed in Europe for the past eighty years. More than 200 shafts, covering a wide variety of ground conditions, have been sunk by the freezing process, and most of these have been lined with cast iron tubbing. The No. 1 shaft of International Minerals and Chemical Corporation, near Esterhazy, Saskatchewan, comprises the first major example in Canada of the employment of European methods to overcome extremely difficult ground conditions. The Blairmore formation was solidified by the deep freezing process, employing a lithium chloride solution as the refrigerant, with input temperatures ranging to -55°F

Jan 1, 1964

By Nordau R. Goodman

"IntroductionTHE HISTORY of Nova Scotia's gypsum industry goes back about two hundred years. The extensive deposits found in the Windsor formation, which is Lower Carboniferous, were the first discovered in North America and were known to the earliest .settlers. There has been a steady increase in production from these beds, except for minor setbacks in years of wars and depressions, but at the same time there has been a decrease in the number of operating quarries. This decrease reflects the change from the days of horse-and-cart recovery to the modern, large-scale, highly mechanized operations. In the beginning, almost any outcrop could •supply the tonnage requirements and the most •convenient were selected, but the millions of tons needed to meet present-day needs are not easily found.Despite the size and importance of the Nova Scotian deposits there has been little detailed geological work. Sir Charles Lyell, in 1843 ( 10), established that the beds are Lower Carboniferous and this was confirmed by Sir William Dawson (3) a .few years later. Both Lyell and Dawson agreed the calcium sulphate beds were an original part of a bedded series .but did not consider they resulted from a concentration of sea water. Lyell reached the conclusion that the gypsum was related to volcanic action in the form of heated vapours or hot springs. Dawson believed it was formed by the action •of sulphuric acid on calcium carbonate. The acid, derived from the oxidation •of iron pyrites which was abundant in the older formations, was carried by rivers into basins which were rich in shells."

Jan 1, 1954

By F. P. Hassani, Jacque Ouellet, M. Hossein

A laboratory investigation was undertaken to evaluate the effectiveness of different binding agents in a paste backfilling operation suitable to be used in a sulphide-rich environment. Different combinations of Portland cement and fly ash type C as well as ferrous slag were used as the binding agents. The unconfined compressive strength of the samples was measured for extended curing periods. The results indicate that the addition of 3% slag in the binding agent mix could produce strengths up to 0.5 MPa in the samples under investigation. For higher binding contents, the addition of Portland cement will lead to higher availability of calcium hydroxide and calcium aluminate, which are susceptible to deterioration from the phenomenon known as sulphate attack. Using slag, on the other hand, will reduce the permeability, availability of calcium hydroxide, and dilute the calcium aluminate ions reducing the susceptibility of the samples to sulphate attack. However, gypsum will form which could have the same detrimental effect on the strength of the treated matrix. Therefore, special attention must be given to the content and properties of agents used to activate the pozzolanic properties of the slag.

Jan 1, 2001

By C. M. Anson

This paper describes the progresses used in the manufacture of steel wheel-centres, tyres and axles at the works of the Commonwealth Steel Products Co., Newcastle, N.S.W., Australia. The plant is adjacent to the Northern railway and consists of three main buildings, namely: the foundry, the forging and rolling shop, and the machine shop. The foundry contains a 6-ton Heroult electric furnace, together with all necessary mechanical appliances for moulding. Reheating furnaces, steam hammers and tyre rolling mill are installed in the forging shop. The machine shop contains lathes, boring machines, and hydraulic presses. Until this plant commenced operations all wheels used in Australia were imported, previ.ous to the war, from England and Germany, and latterly from England only. Besides being of great benefit to the country in that there is now a domestic source of supply of these articles, there is also the advantage of retaining the home market; and in addition, a small portion of the population are now engaged in highly technical occupations requiring a great degree of skill. The plant began to operate in October 1919, and by 1921 was in a fair way to meet the domestic demand for those articles of railroad equipment which it manufactures.

Jan 1, 1925

By John H. Morris, R. Gwilym Roberts

"The Upper Beaver Mine, Kirkland Lake, Ontario, is a copper-gold deposit in mafic flows and sedimentary rocks. The deposit consists of a number of orebodies of two types: copper- and gold-bearing chalcopyrite-pyrite-magnetite ore; and gold-bearing quartz veins. Chalcopyrite-pyrite-magnetite ore occurs in two structural forms: as cherty interflow material in coarse clastic roks underlying flows; and as veins. Both sedimentary and vein ore occur in each orebody. The goldbearing quartz veins occur in interflow sedimentary units and at the contacts of oligoclase porphyry dykes.The deposit is in a localized, volcanic-sedimentary basin which began to develop during the emplacement of the upper units of the pyroclastic and sedimentary Gauthier Group, and continued to the early mafic flow activity of the overlying Kinojevis Group. The formation of the volcanic-sedimentary basin is ascribed to the D0 deformation. The deformation is significant in terms of the structural configuration in the mine area, and may be significant regionally, but this has not been demonstrated. The early deformation was followed by two tectonic deformations. D 1 is associated with a penetrative mineral foliation, axial planar to upright mesoscopic folds and striking parallel to the trend of regional fold structures. Mesoscopic flexural-slip folds, kink folds and fracture-crenulation cleavage are attributed to the D2 deformation. It is probable that no large-scale fold structures are associated with the D2 deformation. The gold-bearing quartz veins were folded during the D1 deformation.The close spatial relationship of copper-gold, chalcopyritepyrite- magnetite veins with chalcopyrite-pyrite-magnetite in cherty inter flow material is strong evidence for the derivation of the veins from the sedimentary ore by hydrothermal, metamorphogenic processes. By analogy, it is suggested that the gold-bearing quartz veins were formed by similar processes."

Jan 1, 1982

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By Sazol Das, Hany Ahmed, Ganesh Bhaskaran, Zhuoru Wu

"Friction stir welding (FSW) process in lap configuration for dissimilar materials has been developed and tested for steel to aluminum joining. A novel cylindrical tool was designed for improved material flow. The joining of steel to high strength 5xxx and 6xxx aluminum was carried out by FSW technique using optimized process parameters. The microstructure, micro-hardness, joint strength and corrosion properties at the weld interface have been investigated. Optical and scanning electron microscopy reveled a well layered structure at the interface and lap shear tests of the welds showed excellent fracture resistance. Neutral salt spray tests for up to 500 hours (ASTM B117) were carried out on the bare steel to aluminum FSW joints, which did not show neither evidence of corrosion at the weld interface, nor any degradation of the weld strength. The FSW lap configuration was applied to prototype commercial vehicle structural component whereby a steel stiffener insert was friction stir welded to high strength 6xxx aluminum alloy. The interface microstructure showed layered root without any steel shattering in aluminum side. A finite element study was carried out to quantify the benefits where it was found that the stiffness increases by 76% under bending loads and 36% in torsion loads.INTRODUCTION Energy preservation and environmental issues, namely carbon footprint and legislation around emission in transportation industries has led to a growing need to use of lightweight materials such as aluminum and magnesium alloys along with various grades of steel in structural application, while still maintaining their strength and crashworthiness. Assembling dissimilar materials within integrated structure is thus a stringent requirement related to optimum performance. In order to achieve an efficient technology of joining dissimilar materials such as aluminum to steel, it remains difficult to select an effective welding process for a given joint configuration. The use of aluminum in transportation industries for structural component is not exclusive in a design and is almost always used along with various steel grades for a mixed materials solution, thus dissimilar aluminum/steel lap joining is of great interest since this is widely used in the assembly of parts (e.g. pillar, frame rails, chassis, body in white (BIW), CAB, etc.)."

Jan 1, 2018

By M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterite ores typically extracts 95% of the nickel and 91% of the cobalt. Impurity elements in the feed, such as iron, aluminium and chromium, also dissolve and can be detrimental to downstream processes. Rejection of impurities within the autoclave is highly desirable. Aluminium and iron hydrolyze, and then precipitate in the autoclave leaving only small amounts that are subsequently removed by precipitation in a neutralization step. The concentration of dissolved chromium can range from 200 to 2000 ppm, depending on the feed composition. Chromium in the liquid phase, usually in the hexavalent state, introduces many problems and can limit refining options. For example, chromium poisons the organics in solvent extraction making SX an expensive option. Also, hexavalent chromium must be converted to the trivalent state before it can be precipitated along with iron and aluminium. Bench-scale work confirmed that mixing small amounts of carbon-base additives, such as coke, with the autoclave feed significantly reduced chromium concentration in the autoclave discharge without any detrimental effects on paymetals recoveries and selectivity.

Jan 1, 2004

By S. Mathieu, R. Mennillod-Blondin, P. Cousin, N. Valle, H. Bouzahzah, P. Marion

The gold deposit of the Lapa mine has a complex mineralogical gold state with coarse and fine native gold, aurostibite and submicroscopic gold within arsenopyrite. A specific mineralogical characterization of the refractory fraction was conducted combining various techniques such as optical microscopy, electron microscopy, electron microprobe and secondary ion mass spectrometry. In parallel, the mineral processing behaviour and the recovery of the refractory gold were studied by pressure oxidation and cyanide leaching. This paper presents the mineralogical methodology developed to characterize the refractory gold distribution within arsenopyrite. These results are presented and interpreted in order to plot gold recovery versus sulphide oxidation. The comparison of the metallurgical behaviour yields predicted from the mineralogical data and the one calculated from leaching tests shows a good agreement and allows mineralogical explanations of the gold metallurgical behaviour.

Jan 1, 2011

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997