Search Documents

By Janne Karonen, Stephen Hughes, Mikael Jåfs, Jan Stål, Hannu Johto

End-of-life electrical and electronic scrap material attracts attention as a good opportunity for new value creation through efficient metal and energy recovery of such materials. On the other hand, the treatment of such wastes becomes important to avoid problems for society and environment. Treatment of such secondary raw materials faces multiple challenges due to their increasing complexity and evolving nature. Processing of these complex scrap materials together with recovery of a wide range of valuable metals with a combination of pyrometallurgy and hydrometallurgy using Outotec technology is discussed in this paper. One key consideration is environmental performance which needs attention when processing such complex secondary E-waste materials. Outotec has successful experience with commercial projects in the countries at the forefront of environmental and operational standards. INTRODUCTION Increasing attention has been drawn to the responsible processing of end of life Waste Electrical and Electronic Equipment (WEEE) as part of metals recycling, especially copper. It has been estimated that the amount of WEEE globally in 2016 was around the level of 46 Mtpa (Balde et al., 2017), representing a major disposal challenge but at the same time huge opportunity for resource recovery. The potential for increasing the recovery is high, because the official recycling rate of WEEE is in 2016 only 20% (Balde et al., 2017) and at the same time the estimated increase of the WEEE amount is between 3 and 5% per annum in the EU (Eurostat, 2019).

Jan 1, 2019

By R. L. Bruening, J. B. Dale, N. E. Izatt, S. R. Izatt

IBC Advanced Technologies' Molecular Recognition Technology (MRT) SuperLig® products selectively and rapidly bind with target metal ions to remove them from solution. The MRT process can produce a high purity separation product of maximum added value at low cost. This paper discusses applications for MRT in the gold industry, including recovery of gold and silver as well as metal contaminants from various process and recycle streams.

Jan 1, 2011

By Yan Yang

The Jinfeng gold mine is one of the three gold mines that Eldorado Gold has in China and it is the second largest gold mine in China. The mine is located in a relatively remote and mountainous area in the southwestern Guizhou province. The orebody is similar to the Carlin type deposit in Nevada. The mill throughput was designed to treat 3,600 tones per day. The ore comes from open pit mining and underground mining, and is fed to one-stage jaw crushing. The crushed ore is stockpiled, reclaimed and then fed to the SABC grinding circuit. After classification with hydrocylones, the ore is floated, and the resultant concentrate is oxidized biologically in a process known as BIOX®. The oxidized concentrate is then washed in a CCD circuit and finally leached with cyanide in a CIL circuit for gold extraction. Jinfeng produces about 180,000 oz of gold per year. This paper introduces operations and modifications of SABC circuit over the past three years, and then describes some technical characteristic of the SAG mill and other circuits in the processing plant. Major modifications and improvements on the SABC circuit are described in the paper, including: 1. Impacts of grinding ball and mill liner with respect to material selection, quality, hardness, manufacturing methods, and interactions between mill liner and grinding ball. 2. Effect of milling operation parameters on milling efficiency. 3. Impacts of SAG mill scats and modifications of grate size to improve mill throughput. 4. Design and construction of a pebble crushing system, and recycle the crushed scats to the SAG mill to improve mill throughput. With the above-mentioned modifications, 20% increase over the design in mill throughput has been realized over the past three years, and operating cost has been significantly reduced. However, some issues still remain, and thus process modifications and technical innovations are still needed.

Jan 1, 2012

By S. S. Dimov, B. R. Hare

This paper describes two micro-beam analytical techniques(Dynamic SIMS and TOF-SIMS) which have become an intricate part of a comprehensive analytical approach for precious metal (PM) ore characterization and process mineralogy or deportment studies. The value of the D-SIMS technique is its capacity for accurate analysis in the sub ppm range along with the ability to produce high resolution elemental maps. The TOF-SIMS is significant for speciating and quantifying preg-robbed Au on the surface of carbonaceous material. In combination with traditional assays, the two techniques can provide invaluable information regarding the distribution of PMs within an ore along with providing insight into potential sources of PM loss in processing or where losses have occurred in process streams.

Jan 1, 2011

By B. Crane, S. Schwartz

"IntroductionThe Cape Breton Development Corporation (CBDC) located in Cape Breton, Nova Scotia, in eastern Canada, was established in 1967. Its mandate at that time was to facilitate a phased downsizing of the coal industry and developing viable replacement industries. The oil crisis in the early 1970s changed CBDC’s mandate and focus was modified to increase coal production to support Nova Scotia Power Commission’s “off oil” policy for their power generators. In the late 1980s the mandate to develop viable replacement industries was eliminated and CBDC became primarily a coal mining company. CBDC presently operates two underground coal mines, Phalen Colliery and Prince Colliery, using a retreat longwall method of mining. Both mines operate beneath the Atlantic Ocean. CBDC also operates associated infrastructure — central workshops, a railroad, coal preparation plant, and international pier. The Need For Substantial ChangeOver the last few years, CBDC has been facing some challenging issues, including improving labour management relations and achieving financial self-sufficiency and profitability. Recent achievements with regard to human resource issues, especially in the areas of collective bargaining, absenteeism, and attendance, show noticeable improvements. All participants should be commended for successfully concluding the collective bargaining process with all four CBDC unions, CUPE; CAW; IAM&AW; and UMWA. However, although these changes are encouraging, even critical in the short term, they are not sufficient to ensure the long-term viability of the company. Market ForcesShort- and long-term financial realities are drawing the need for further substantive changes. The corporation has a mandate to achieve financial self-sufficiency by the year 1999. This goal can only be achieved through a combination of cost reductions and productivity gains, specifically, a reduction in the workforce of 658 and an increase in production of 800 000 tonnes annually. This increase in productivity requires CBDC to re-think the way it does things.In the longer term, CBDC faces even greater challenges. The energy market is becoming more competitive. The electrical utilities across Canada are anticipating deregulation and are positioning themselves for the resultant competition. As primary fuel supplier to Nova Scotia Power Inc. (NSPI), the corporation will have to become ever more competitive to stay in business."

Jan 1, 1997

By Vahid Faghihi

SatraPM is a web-based software package, aiming to help project managers to easily handle their construction projects via internet. This software is capable of handling all projects of an organization, in which all projects can be defined in EPS the same as users in OBS. A 3D accessing module links EPS, OBS and inherent functions in order to provide a secure environment for the data to be processed throughout the system. This paper intends to take a deeper look at capabilities of SatraPM in helping project managers to keep track of and control their construction projects as well as its potential future features.

Aug 1, 2013

By Helmer Kraemer

One of the CIM 2003 conference themes is ?Globalization and the impact on mine operations?. In this context, the first official version of the new ?International Rock Excavation Data Exchange Standard? (IREDES) is being released. This new standard is a highly flexible data interface for exchange of information between production equipment and central computer systems. The standard was defined by global players in the mining industry and will soon be used to enhance local operations of global mining companies. Beside the standard definition now other aspects are coming into focus: The question how to design and how to implement IREDES compliant data exchange in practice. Implementation of IREDES covers the following aspects: !" Implementation on in-field production systems !" Communication and networking !" Implementation on databases and commercial IT systems In-field production systems are characterized by a big variety of different automation systems. Therefor, different IREDES implementation philosophies have to apply to those systems. One philosophy uses an integrated IREDES compliant automation system on every machine. The alternative method uses one shared IREDES compliant ?Proxy server? for a number of machines connected to this server using proprietary interfaces. Communication and networking can be integrated openly and independently from hardware infrastructures. The only precondition is that communication and networking has to be Ethernet - TCP/IP protocol compatible. IREDES Implementation on the commercial IT level means to exchange IREDES data sets with databases, simulation software, office packages and special applications. Interfacing is easy as long as the software or the database system provides an interface to the Extensible Markup Language (XML).

May 1, 2003

By D. Sancho, M. Weber

"At the start of a new shaft project, a specific number of ground investigations are performed. However, it is not uncommon that the ground conditions during shaft sinking may differ from the designed ones. Therefore, it is extremely important to use tools which minimize discrepancies and to include a monitoring system in the shaft design to collect sufficient data. The paper presents an overview of existing monitoring techniques and discusses future works required to improve, not only the construction during shaft sinking, but also the lining design methodology. INTRODUCTION In most cases, the investigations performed at the start of a new shaft are based on the analysis of rock and soil probes obtained from boreholes. In practice, such analysis performed on a single core often leads to different results when conducted by various experts. The discrepancy in core analysis influences further rock mass assessment and design assumptions. It is not uncommon that the ground conditions during shaft sinking may differ from the designed ones, which affects the estimated stress and strain state of the shaft lining. Therefore, it is extremely important to use tools which minimize such discrepancy and to include into the shaft design a monitoring system to collect sufficient data, which enables control of important phenomena, not only during shaft sinking but also during the life of the shaft. Furthermore, the information collected during shaft sinking, while it is important for proper shaft lining design and updates to the shaft lining due to the local mining and geological conditions, it is also important after shaft sinking. In the whole shaft lifetime, it is not uncommon that the shaft lining is damaged and the liner needs to be renewed (Figure 1) due to various reasons. For this purpose, detailed information collected during construction can be extremely important."

Jan 1, 2019

By Wang Xianzheng

For a long period of time, the Chinese Government has been attaching great importance to and supporting the rapid development of the coal industry. Particularly since more than 30 years ago, when China introduced the Reform and Opening-up policy, the reform and development of the Chinese coal industry has witnessed world-recognized achievements. National coal production increased from 618 million tonnes in 1978 to 3.52 billion tonnes in 2011. While China?s coal production accounts for 49.5% of the world?s total, its annual production growth contributes to over 80% of global production growth. China is a country utilizing coal as its main source of energy. As the Chinese Government gives support to the rapid development of new and renewable energy sources, as well as to increased coal utilization efficiency, the ratio of coal in the primary energy consumption mix will gradually decline. However, for a long period of time to come, the total volume of coal demand will keep rising modestly. The Chinese Government has been highly committed to and actively promoting the overall, coordinated and sustainable development model, which puts people first. It has put forward a strategic task to build an ecological civilization, and highlighted its resolve to uphold the basic national policy of resource conservation and environmental protection, with a view to the pursuit of sustainable development. China will incorporate its response to climate change into the national economic and social development program, and take effective measures to lower CO2 emissions 40?45% per unit of GDP in 2020 compared to 2005. At the same time, China will increase the ratio of non-fossil fuels to 15% in the primary energy consumption mix. All of the above factors have raised requirements for the Chinese coal industry, with implications for clear directions, plans and goals for the development of the coal industry.

Aug 1, 2013

By H. L. Snyder

This paper outlines the approach to the underground construction work involved in the Churchill Falls Power Project. It is the first in a series of papers which CIM Bulletin plans to publish as the different 11hases of this large-scale operation evolve.

Jan 1, 1968

"Dry crushing trials at pilot scale have shown that the IMPTEC Super-fine Crusher has the capacity to generate ultra-fine products from hard mineral assemblages presenting at either coarse or fine feed sizes. The super-fine crusher was introduced at the 27th International Mineral Processing Congress in Santiago Chile, with results from a range of duties, which demonstrated the crusher’s potentially expansive operating scope. This paper focuses on current preparations to progress the technology from pilot scale to commercial scale within a concrete production plant, where lead blast furnace slag will be crushed to ultrafine sizes to generate an active silica product for use as a supplementary cementitious material, which can replace Ordinary Portland Cement. A key objective of the operation is to demonstrate an economical route to reducing the cost of concrete production, improving concrete quality and reducing greenhouse gas emissions. The paper also highlights the potentially key contribution super-fine crushing can make to the long-term viability of iron ore beneficiation by simplifying comminution flow-sheets and reducing operating costs. There is every indication that the technology has the potential to feature universally in metalliferous and industrial mineral flow-sheets. INTRODUCTIONToday’s IMPTEC super-fine crusher is the successful end product of development work over 19 years and is the third particle size reduction device conceived, built and tested over that time. The concept evolved as engineering design progressively developed a mechanism capable of harnessing a highly efficient combination of fundamental particle breakage mechanisms. Early development trials at pilot scale indicated that super-fine crushing had the potential to establish a wet or dry, media free, low energy route to ultra- fine products from hard mineral assemblages. Having achieved some impressive results from open circuit pilot tests on fly ash and granulated blast furnace slag it became clear that the cement industry may well provide opportunities to apply the technology commercially. Following expressions of interest from local cement and concrete plant operators, IMPTEC negotiated an agreement to undertake commercial trials with a SFC 350 super-fine crusher installed on site at a concrete supply plant in South Australia. Super-fine crushing scope was recently expanded following further expressions of interest from research groups involved in the processing of iron ores. Pilot trials are progressing in these areas."

Jan 1, 2016

By C. H. B. Leitch

"The Bralorne-Pioneer deposit produced more gold than any other deposit in British Columbia over its 70 years of operation (130 kg or 4 million oz of Au, from 7 million tonnes of 18 glt ore). Mineralization is related to a suite of late Cretaceous albitite dykes of 85 to 90 Ma age. It thus occurred long after and is genetically unrelated to the Early Permian (275 Ma) Bralorne diorite and soda granite.The major veins strike about 110 degrees and dip north at 70 degrees, with slickensides plunging 45 degrees east that indicate last movement was reverse. Major ore shoots in the veins occupy somewhat less than 20% of the vein and plunge steeply west, roughly perpendicular to the slickensides. The structures that contain the veins probably formed at around 95 to 90 Ma during a strike-slip episode with easterly directed maximum compression.Disseminated pyrite, pyrrhotite, and minor chalcopyrite occur within envelopes up to several metres from the veins. Arsenopyrite is confined to vein selvages. Local sphalerite and galena appear to correlate with gold-rich portions of the veins. Traces of tetrahedrite and stibnite have been observed but tellurides have not. Gold is found principally as thin smeared flakes of the native metal in the black sulphidic septae of the strongly ribboned veins. Hydrothermal alteration envelopes around the veins grade outwards from intensely foliated quartz - ankerite - sercite (±fuchsite) to less sheared calcite - chlorite - albite to unsheared epidote -calcite.Open-space vein filling textures found in the deep (mesothermal) environment at Bralorne can be explained by a fault- valve model. High-angle reverse faults may have acted as fluid-pressure activated valves on geopressured reservoirs, causing large cyclic fluctuations in fluid pressure that promoted mineral deposition in an episodic fashion . The faults that were mineralized were reactivated sub-vertical former strike slip faults, oriented at a high angle to the northeast-directed stress in a compressive regime."

Jan 1, 1990

By B. K. Mishra, Subrat Kumar Padhy, B. C. Tripathy, I. N. Bhattacharya

Manganese is a difficult metal to electrodeposit due to its high electronegativity and continues to possess unique process challenges. Manganese deposits of high quality are electrodeposited on 316 grade stainless steel from sulphate solutions in the presence of organic additives such as tetra ethyl ammonium bromide (TEABr), tetra propyl ammonium bromide (TPABr), and tetra butyl ammonium bromide (TBABr). The concentrations of these additives were examined over a relatively broad range to evaluate their effect on current efficiency, specific energy consumption and deposit morphology of the electrodeposited manganese metal. A maximum current efficiency of 68% was achieved in the presence of TEABr in the bath. X- ray diffraction studies revealed that (330) (411) planes were the most preferred planes of crystal growth during manganese electrowinning at a current density of 500 A/m2 resembling alpha-manganese irrespective of the nature of additive. Scanning electron micrographs showed smooth and uniform deposit morphologies when manganese was electrodeposited in the presence of TEABr.

Jan 1, 2014

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

Coal shearers are one of the major sources of dust and fines in underground coal mines. Despite considerable research investigations, no comprehensive in situ investigations coupled with extensive laboratory studies on the effects of drum design on generation of dust and fines have been found. It may be for this reason that many major shearer drum manufacturers persistently employ a certain drum-lacing pattern on current coal shearers, which is believed to cause excessive dust and fines in coal mines. This paper shows how respirable dust and fines are minimized under near-identical conditions when the drum lacing pattern was changed from a triple-tracking to a single tracking arrangement. A series of laboratory trials simulating in full scale the practical cutting action of tools was followed by extensive long-term underground trials during production operations in OAL (Cayirhan) Lignite mine in Turkey. The results are presented and discussed, and recommendations for proper drum-lacing in terms of respirable dust and fines are made.

Jan 1, 2002

IN 1932, the No. 4 shaft at Wright-Hargreaves mine was completed to a depth of 4,000 feet, and the lowest operating level at that time was at 3,900 feet. It was realized that the existing pumping system, using triplex plunger pumps at somewhat irregular depths in the mine, would be in-adequate to take care of the increasing volume of water that would have to be handled as mining operations expanded. Accordingly, in February, 1932, after a thorough study of the whole matter, it was decided to instal an entirely new, automatically controlled, system of pumping, employing centrifugal pumps, with their characteristically trouble-free performance, operated by off-peak power.

Jan 1, 1939

By Francis Wm. Gray

The preparation of a paper read before this Society in 1927 on Undersea Mining led to representations to the Deputy Minister of Mines at Ottawa, Dr. Chas. Camsell, and to the Director of the Geological Survey and the Director of the Mines Branch, which resulted in the undertaking by these bodies of a geological, physical, and chemical survey of the Sydney coalfield, combined with revision of the geological maps, on all of which much progress has been made. Preliminary studies revealed the necessity for a new base-map on a scale that would permit the representation of the whole coalfield from cape Dauphin to Mira bay on one sheet, and in the making of this map the Geodetic and Topographical Surveys have collaborated, with the assistance of airplane surveys for filling-in of detail. The new map will show all the data accumulated by 50 years of active mining and will show also the extent of mine workings, with level-contours under the sea. Dr. W. A. Bell, of the Geological Survey, has, over a number of seasons, studied in the field the historical geology with the purpose of elucidating the sequence of earth movements that have determined the structure of the coalfields, especially those that have governed the course and extent of the complementary folds that traverse the Sydney coalfield. Dr. B. R. MacKay, of the Survey, and the officers of the Fuel Testing Laboratories at Ottawa have made exhaustive studies of the Phalen seam, chemical and microscopic, intended to elucidate the conditions under which this seam was deposited, and some very interesting conclusions have been reached.

Jan 1, 1934

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

By Thomas M. Ware

"MR. Chairman, our Honourable Minister, Mayor Cole, it is a pleasure for me to come here, and join with you in one of the largest industrial shows ever held in Saskatchewan.It is an honour to be asked to keynote your meeting, to help mark an early chapter of this new industry for Saskatchewan. God has placed in our hands a new resource for His man on earth. This store of potash, 350 million years in the making, offers a vital resource to help man support his advanced intellect for thousands of years. It is a gift so large we must all wonder at its purpose and our responsibilities in serving our fellow man with it.We who are here to plan and implement the development of this essential mineral resource enjoy a great -privilege; and we share a great responsibility -to see that the billions of tons of potash which have waited beneath these prairies for millions of years are widely and wisely used to nourish the earth through future millenniums.To know the true value of potash, to be able to bring forth this re-source from over 3,000 feet deep in the earth, to establish markets and develop its potential worldwide is all part of our great heritage from generations past. So I think it is fitting on this occasion that we reflect for a moment on this heritage, to help us assess the responsibilities of its future development."

Jan 1, 1966

By P. Condori

Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit. This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration. The achieved plant stability and increment of ore throughput are also reported in this paper.

Jan 1, 2012

Abstract - A method to extract certain types of error variance information from paired data is presented, which constitutes an important tool for the calibration of Gy’s formula for variance predictions in the sampling of broken ores. The research summarized here complements publications by others on geochemical precision. The model and method proposed for treating duplicate data provide a practical means of deriving separate estimates of the purely analytical and aliquot sampling variances, from a unique set of duplicate assays, and, hence, proposes a new avenue for estimating effective mineral grain size.

Jan 1, 1998