Search Documents

By J. Ji

Oxygen requirement during acidic pressure oxidation of sulphide concentrates can he as high as 800 kg/(m3.h) in the first compartment of an autoclave when the total oxidation residence time is shortened to 30 minutes. To achieve such a high oxygen transfer rate while maintaining satisfactory oxygen utilization, a pilot plant campaign was launched at the Placer Dome Research Centre in 1998 to measure the oxygen mass transfer coefficient in a 5 m3 pressure vessel at a total pressure close to 500 psig with a 30 HP gassing agitator. Maximum oxygen flowrate to the pressure vessel was designed at 3 600 kg/h. In this paper, a great deal of information is provided on the gassing agitator, pressure vessel. measurement procedure and results. Without oxygen sparging, the oxygen mass transfer coefficient is 2 600 h-1 with a mixing power input of 5.0 kW/m3 in solution. With oxygen sparging, the oxygen mass transfer coefficient increases to 3 500 h-1 with a mixing power input of 4.0 kW/m3 in solution.

Jan 1, 2004

By I. C. Brown, J. F. Henderson

"IntroductionThe Yellowknife greenstone belt lies along the west side of Yellowknife bay on the north shore of Great Slave lake, some 600 miles north of Edmonton, Alberta. The producing gold mines along the belt include the Con-Rycon and Negus which came into production in 1938 and 1939, and the Giant Yellowknife, which followed in 1948. In addition to these, the Akaitcho and Crestaurum mines are potential producers and there are several promising prospects.Early geological work along the belt was done by A. W. Jolliffe who first recognized a number of great faults, the largest of which is the West Bay fault with a horizontal movement of more than 3 miles. In 1943, A. S. Dadson, following an examination of the Giant-Yellowknife property, advanced the hypothesis that Baker Creek valley was underlain by a series of major gold-bearing shear zones. Subsequent diamond drilling in 1944 bore out the correctness of this view and outlined the great ore-bearing shear zones that are now being developed and mined by Giant Yellowknife Gold Mines. Near the south boundary of the Giant property, the shear zones are cut off by the West Bay fault. This prompted Neil Campbell, District Geologist for the Consolidated Mining and Smelting Company, to make a detailed study of the geology along the West Bay fault in the hope of finding the faulted extension of the Giant shear-zone system on the west side of this fault. In this he was entirely successful. By careful geological mapping he matched several faulted diabase dykes on both sides of the fault and, knowing their dip, determined the horizontal and vertical components of movement along the fault. Subsequent •diamond drilling based on Campbell's work located the presumed correlative of the Giant shear-zone system on the Con-Rycon and Negus properties, where it has been named the Campbell zone or system. At the present time, all production at the Negus Mines property is coming from orebodies along the Campbell zone."

Jan 1, 1950

By Cristina Echavarría

MAIN POINTS ? The region: opportunities and limitations ? Overview of main issues emerging from MMSD in South America ? Who comprises the local community? ? What are the main challenges? ? Some suggestions for companies to improve their contribution to local sustainable development of mineral rich localities THE REGIONAL CONTEXT 1. The region is a producer of minerals contributing over 20% to world metal production. It consumes only 8% 2. Significant diversity of national contexts-both between countries and within countries 3. Variable but predominant need for strengthening of government and community institutions and governance, especially at the local level 4. Dearth of baseline information for decision making 5. Sustained social spending during early 90?s as a consequence of economic recovery and fiscal policy, produced important advances in education and health 6. Despite government efforts in most countries poverty continues growing 7. Highly inequitable distribution of wealth persists

May 1, 2002

By Roussos Dimitrakopoulos

Overview ?Uncertainty matters: The economic side ?Models of geological uncertainly ?Shifting the paradigm: Stochastic mine planning ?Using uncertainty to improve project performance ?Conclusions: Quantified uncertainty based models are great!

Oct 1, 2010

By C. T. Dzgoev, S. S. Gudkov, IRGIREDMET JSC, S. G. Schtoick, A. V. Yepiforov, S. V. Balikov, I. I. Yevtuschevich

The pressure oxidation (POX) and pyrometallurgical process comprises POX of gold containing sulfide and polymetallic lead-zinc concentrates prior to reduction smelting of POX products to generate a lead-silver-gold alloy. Refined lead and gold-silver alloys are then obtained using conventional processes. Zinc and other base metals are recovered from the POX solution. In the course of POX, zinc dissolves in the solution and lead concentrates in a solid residue in the form of sulfate compounds. Sulfur forms the major iron sulfates and jarosites. In order to dissolve sulfur and arsenic from solid residues to the solution, the slurry hot curing was carried out at the temperature of 95°C within 2 hours. After filtration of the slurry, zinc was recovered from the solution. The resulting cake was washed with water and subjected to hot alkaline treatment. After alkaline treatment, the cakes were blended with fluxes and subjected to reduction smelting to generate lead concentrate containing precious metals. This concentrate was refined to obtain refined lead and gold-silver alloy. After iron and arsenic were removed from POX solutions using sodium carbonate, zinc was precipitated as carbonate. After thickening and filtration, zinc precipitate was roasted to generate saleable zinc oxide. Using this process, the recoveries of values to saleable products were 97% Au and 95% Ag to the alloy, respectively, 91% Pb to refined lead and 5% Pb to lead and antimony alloy and 94% Zn to zinc concentrate. The features of the technology is that it has high recovery indices of precious and base metals to saleable products and can be used to process various polymetallic ore and technogenic raw materials.

Jan 1, 2016

By G. Macfarlane

"In 1985, a crushing plant, located in the feed preparation area of Kidd Creek's copper smelter, was modified. The plant, which originally had treated only copper-bearing materials for the smeller, at a rate of 10 tonnes per hour, was expanded to 40 tonnes per hour capacity and modified to treat silica ores to meet the smelter’s flux requirement and also gold ores from the company's Hoyle Pond property. In the storage area adjacent to the crushing plant a 300 tonne per day gold mill was constructed.This paper outlines the construction and first year of operation of the crushing plant and gold mill with emphasis placed on the capital and operating advantages to be gained by utilizing an existing metallurgical infrastructure.IntroductionThe Kidd Creek Mines Ltd. copper-zinc-silver orebody is located 24 km north of Timmins, in Northern Ontario . Mining of this massive sulphide de posit commenced in 1966 and, in the ensuing years, a concentrator and zinc plant were constructed at the metallurgical complex, approximately 17 km by rail from the mine site . At this same site, in 1981, a copper smelter and refinery were commissioned. The smelter which utilizes the Mitsubishi smelting process for the continuous production of blister copper from copper concentrate, has been comprehensively described in previous papers.At the time of the smelter construction, a small (10 tonnes per hour) crushing plant was installed in the smelter's feed preparation area. This plant was used to treat the copper-bearing revert material produced by the smelter, and, apart from periods when slags and matte were produced through furnace drainage at the end of each operating campaign, it was generally under-utilized. This fact, together with the requirement to devise a more cost effective method of providing silica flux for the smelting operation, was the basic rationale for modifying and expanding and crushing plan t. At the same time, development at Kidd's Hoyle Pond orebody had progressed to such a stage that a gold mill of 300 tonnes per day was warranted."

Jan 1, 1988

By D. J. Scarpato

"Slope construction in shale can present some interesting challenges for geotechnical design engineers and contractors alike. There are challenges that can be expected and designed-for; however, all too frequently, such challenges manifest themselves as “surprises” in the field. Common constructability challenges can include those such as drill hole deviation during drilling for controlled blasting; and, excavation slope instability arising from inconsistent perimeter control drilling. Drill hole deviation results from the cumulative effects from both drilling mechanics and rock mass conditions. Once a hole has initiated the deviation trajectory, it is difficult to rectify drill steel position. Although such challenges are not necessarily unique to shale, they are often exacerbated by weak, weathered and transversely isotropic nature of bedrock conditions. All too often, the working assumption is that shale is “soft” and easily excavatable; however, this blanket assumption can prove to be costly. This paper is intended to provide design professionals and contractors with the practical considerations needed to avoid the “surprises” associated with drill hole deviation, and minimize the potential for costly claims.INTRODUCTIONFor all the slopes that have been excavated worldwide, and for such advancements in excavation technology and field characterization, one might be tempted to believe that the industry almost has slope development down to a science. This is frequently not the case, especially for weak/weathered and anisotropic bedrock. Excavation contractors are still pushed to the limits of what their technology can achieve, and engineers are all too often called to the field during construction, to make potentially risky onthe- fly decisions relative to excavatability, short and long-term slope stability, and project safety. Although there have been a host of other research papers and journal articles that have been written on the subject of deviation over the past 30 years (Brown, Geen, Sinha, 1981), the problems associated with drill hole deviation are still all too frequent. This fact is especially true for civil engineering surface excavations in bedrock."

Jan 1, 2015

By J. Ouellet

"ABSTRACTA brief background on in-situ testing of mine backfill, as well as pressuremeter testing is briefly described, and results from an in-situ testing on paste backfill are presented. A series of self-boring pressuremeter tests were done from the top of a backfilled stope in an underground mine. The tests were conducted along a 20-metre vertical line in the centre of the stope. Some 14 tests were performed along this depth. The instrument used was a Camkometer built by Cam Insitu, Cambridge. The instrument proved to be efficient and reliable for underground testing in a cemented paste backfill. The testing program was conducted within the planned schedule with a high success rate. The test done in this study permitted the measurement of paste backfill strength, stiffness and in-situ horizontal stress within the backfill. RésuméUn bref historique des essais in situ dans le remblai minier est présenté. L’essai pressiométrique est décrit succinctement et des résultats d’une campagne d’essai dans un remblai en pâte sont présentés. Un programme d’essais au pressiomètre auto-foreur a été réalisé à partir du sommet d’un chantier remblayé sous terre. Les essais ont été réalisés le long d’un ligne vertical d’environ 20 mètres pour un total de 14 mesures. Le Camkometer de la firme Cam Insitu de Cambridge a été utilisé. Cet instrument s’est avéré efficace et fiable pour tester le remblai en pâte cimenté sous terre. Le programme d’essai s’est déroulé à l’intérieur de l’échéancier prévu avec un taux de réussite élevé. Ces essais ont permis de déterminer la résistance, la rigidité de ce remblai ainsi que les pressions in-situ prévalant dans le remblai."

Jan 1, 2000

Infrared spectroscopic data collected using HyloggerTM technology is being used to assess the mineral composition of Archean iron ore bedrock and Cenozoic detrital units in Western Australia’s Pilbara region. Analysis of infrared spectra enables quantification of: (1) composite iron mineralogy, (2) composite clay mineralogy, (3) hydrous silicates and (4) carbonate mineral abundances. Stratigraphic and rock mass unit logging of core has identified several detrital and bedrock units recognisable across the Pilbara. However, due to alteration related to mineralisation, weathering and later stage precipitate overprinting, it can often be difficult to assess the detrital-bedrock boundary and the occurrences of specific geotechnical units in the detritals and bedrock, particularly when using non-core drilling techniques and traditional geochemical assays. Infrared spectroscopic data collected concurrently on core from several sites has shown distinct correlation against existing unit subdivisions and associated geochemical parameters. Where infrared spectroscopic data have also been collected on rock chips recovered from reverse circulation infill drilling, these correlations allow robust geological and geotechnical models to be developed based on the typical mineralogical-geochemical signatures. The geotechnical sub-units identified in core can be readily distinguished using the various iron and clay minerals captured by the HyloggerTM technology as opposed to total iron, potassium, and alumina captured by geochemical assays. Further, some of the minerals targeted by infrared spectroscopic analysis (eg gibbsite, white mica, vitreous goethite) and their ubiquitous presence as the products of weathering, assist in recognition of various ancient weathering surfaces and help to define the origin of the material, whether bedrock or detrital. Overall, HyLogging of core and chips allows important mineralogy focussed data to be captured at minimal additional financial outlay. Correlations against geochemical unit identifiers are robust both within deposits and between deposits. Significant improvements in the confidence of geological and geotechnical models are attained.

Jan 1, 2015

By Andre du Preez

Emergency Fall Arrest System Rio Tinto?s Primary Objective: ?To achieve repeatable controlled safe deceleration rates during emergency fall arrest activation (Ontario OHSA Regulations) ?Must operate effectively on mine specified steel shaft guides.

May 1, 2013

By E. S. Moore

GOLD was discovered previous to the year 1900 on the east shore of Emerald lake, Afton township, Timagami Forest Reserve. It was found in a small cavern in banded iron formation, close to the water's edge. This occurrence of gold was mentioned in several reports that referred briefly to this area, and prospectors evinced considerable interest in the region. It was not, however, until the Golden Rose Mining Company, which was incorporated in 1909, started operations that much work was done on the property. In 1915-16, this Company, under the direction of E. J. Townsend, the President, did a considerable amount of work. A small mill was built and ore was extracted from pits, trenches, and a one~ hundred-foot shaft. In 1927, Afton Mines, Limited, was incorporated to take over the property, and about thirty men were employed for a time. During 1934, the New Golden Rose Mining Company was organized to handle the property, and the Consolidated Mining and Smelting Company of Canada, Limited, undertook to develop the mine. In March of the following year, this Company began deepening the shaft from 100 feet to 500 feet. A considerable amount of drilling had previously been done on the hill of iron formation in which the mine is located. Further drilling was done from the surface, and altogether about twelve holes have been put down to test the formations. Over 2,000 feet of drilling has also been done from the underground workings. The mine is now known officially as the New Golden Rose mine, although to many it is better known as the Afton. To reach the property during the summer months, there is a boat trip of about thirty miles from Timagami, a wagon-road portage of one mile to Obabika lake, a boat trip of ten miles on this lake, and finally a wagon-road portage of one and one-quarter miles to Emerald lake. The mine lies about three-quarters of a mile down the east shore of the lake. A 75 h.p. Diesel engine and compressor were taken in over this' route last summer, and it is evident that the transportation problem is quite a serious one. Airplanes have been much in use, and a winter road runs from the mine to Chudleigh, on the .Canadian National railway near Sudbury.

Jan 1, 1936

By Bryon Cerklefskie, Michael Schulte

"This case study explores the usage of polymer ducting as a replacement to curtains and FRP for face ventilation in two coal mines. There are two mines looked at, one is the highest elevation underground coal mine in North America, the other is the gassiest mine in North America. The paper details the trials of both mines switching from FRP and curtain respectively to polymer ducting. The results discuss the ability for the mines to not only achieve consistent airflows and keep them in compliance but the unexpected positives. Mine A was allowed to do longer cross cuts due to increased air volume at the face. This drastically cut their costs of mining down due solely to modification of the ventilation cycle. Mine B saw economic benefits due to longer cuts between place changes. Both mines have documented lower dust, methane, noise, and improved wear and tear on their equipment as a result.INTRODUCTIONThe emergence of longwall mining in underground coal operations has resulted in new ventilation challenges. Numerous production crews strive to complete their development sections with enough time to adequately prepare for the upcoming longwall panel. Continuous miners will cut out two or three entry development sections per their ventilation plan, that is approved and controlled by MSHA (Mine Safety and Health Administration), which will drive amount of footage that can be mined at a time prior to installing roof support. At this moment the continuous miner, hereafter referred to as the CM, will back out of the entry and moves to the second entry to complete a similar cut. Typically, a roof bolter crew will pull in to the finished cut section and install ground support. This is called a place change style of production coal mining. There is an alternate method that includes a miner/bolter combination as well but that was not featured at either test site in this case study. Ventilation has to be provided to sweep the working face of each entry to control dust and gasses. Each task will have an MSHA prescribed ventilation requirement dependent on the dust levels and methane emissions of the rock for that particular mine. The CM, roof bolting and unused headings will each require constant ventilation but at different volumes. Since each working face is changing throughout the mining cycle the ventilation requirement in a working heading is never static and is changing with the working task.Traditional Ventilation ControlsTraditionally face ventilation for coal mining operations has been completed thru the usage of a curtain system and\or using auxiliary fans and ventilation tubing. Room and pillar mining systems typically utilize curtain systems, which use curtain walls that are installed by the miners by erecting wood framing and covering it with brattice curtain. This splits the drift width to allow fresh air to sweep the face and take the contaminated air and dust behind the curtain to the ventilation exhaust\return area of the mine. This method is difficult to adjust the airflow from entry to entry during changing cycles and requires that a wider drift is mined out in order to have enough room for the brattice wall. In operations that require roof bolting, this method limits the length of the cuts from the CM prior to advancing and can lead to not providing enough ventilation to keep dust and methane levels below compliance requirements."

Jan 1, 2019

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclones are used in various industrial applications, including mineral processing and tailings management, to separate or classify solid particles and/or liquid droplets from multiphase feed. The fluid flow in a hydrocyclone (used in mineral processing) was investigated numerically and experimentally using particle-image velocimetry (PIV) and refractive index matching techniques. Two turbulence models were used in the calculations: the k–? model and the Reynolds stress model. Particle image velocimetry measurements were taken at various spatial locations along the cyclone. Computational results were validated globally using pressure and flow-rate readings at the boundaries, and locally by comparing the PIV velocity-vector maps and profiles.RÉSUMÉ On utilise les hydrocyclones dans diverses applications industrielles, dont la minéralurgie et la gestion des résidus, pour séparer les particules solides et/ou les gouttelettes liquides de l’alimentation polyphasée, ou pour les classifier. Une étude numérique et expérimentale sur l’écoulement des fluides dans un hydrocyclone (dont on se sert en minéralurgie) a été menée à l’aide des techniques de vélocimétrie par images de particules (PIV, de l’anglais particle image velocimetry) et d’appariement des indices de réfraction. Deux modèles de turbulence ont été utilisés dans ces calculs, à savoir le modèle de turbulence k–? et le modèle aux tensions de Reynolds (RSM, de l’anglais Reynolds stress model). La valeur de la PIV a été mesurée à diverses positions spatiales le long du cyclone. Les résultats de ces calculs ont été validés globalement à l’aide de relevés des pressions et du coefficient d’écoulement d’une extrémité à l’autre de l’hydrocyclone, et localement à des coordonnées spatiales spécifiques en comparant les cartes et les profils du vecteur vitesse PIV."

Jan 1, 2017

By R. Jacobs, R. E. L. Pobe

The Moab Khotsong Metallurgical Complex comprises a gold recovery circuit (Noligwa Gold Plant) and a uranium recovery circuit (South Uranium Plant). The metallurgical complex employs the reverse leach technology for the recovery of uranium; specifically, uranium extraction prior to gold using acid leaching processing. The inherent uranium species in the ore are uraninite, coffinite and brannerite. The slurry that has been subjected to the uranium leach is further subjected to solid-liquid separation to separate the uranium in solution through counter-current decantation and the solids (solids carrying all the gold), which are repulped and returned to the gold plant for gold processing. The uranium leaching process is critical to the uranium playing a pivotal role as a value adding by-product to the gold operation. The benefit of adopting this reverse leach process, for improved gold recovery, is that it exposes gold particles occluded within the uranium matrices and avails them for cyanidation. However, the drive for operational efficiency in uranium extraction must be weighed against the incremental operating cost against the backdrop of depressed spot uranium market prices. Over the years, efforts were directed at maintaining the benefit of extracting uranium to enhance gold recovery and simultaneously, optimizing the operating cost model for the uranium operation to remain relevant to the gold operation. The aim of this paper and the corresponding presentation is to give account of the uranium processing optimization journey embarked on over the years; namely, the operational trade-offs made in the process of ensuring that uranium continues to add value to the gold operation. These challenges were faced while striking a fine balance between processing cost and operational efficiencies against the prevailing depressed uranium spot market prices. Mineralogical- and laboratory tests conducted form the support basis for the results and observations articulated in the paper.

Jan 1, 2020

By Sydney H. Ball

It is a peculiar anomaly that while the world uses the term "rich as a gold mine" as the superlative figure of speech descriptive of wealth, the shares of gold mines are not as popular investments in America as certain of them should be. One of the most able of Manhattan's bankers is a director in an investment trust with a portfolio the value of which has gone the way of other such portfolios. Luckily a couple of years ago a few hundred shares of Homestake were purchased, and since then the trust has not only received therefrom satisfactory dividends but has benefitted from a large appreciation in their value. At each directors' meeting, however, the banker in question, Cato-like, suggests the sale of these shares, gold shares being, in his opinion, too speculative to be included in the portfolio of any trust. A short time ago the financial pages of one of our great metropolitan papers featured an article listing the corporations still paying dividends at the 1929 rate. Gold-mining shares were, the article stated, excluded, although in reality every gold mine on the New York Stock Exchange paid higher dividends in 1932 than in 1929. This 'Alice in Wonderland' treatment of the gold-mining shares is admittedly a bit confusing to those of us who believe that the shares of certain gold-mining companies have a rightful place in any well diversified portfolio. It should, however, here be recorded that whereas, fifty years ago, in America, gold-mining shares were considered by the public as instruments of nefarious gambling, now shares of the better gold mines are sought by astute investors. In England for well over a generation their value as sound investments has been widely recognized.

Jan 1, 1933

By S. Steinlechner, G. Schneeberger, J. Antrekowitsch

The recycling of steel mill dusts is getting more and more important. The costs and requirements of land filling are rising and companies are interested in new recycling strategies. The rising of sustaina¬bility hand in hand with the high rate of valuable metals in these residues supports new research activities on the recycling sector. Especially zinc but also iron and lead are economical factors due to the treatment of steel mill dusts. This paper gives a small overview of fundamental studies concerning the chemical and physical composition of these dusts. Furthermore aggregates for the reduction of these dusts in the liquid phase are introduced and compared. The Flash-Reactor, the TBRC-Technology (Top Blown Rotary Converter) and submerged arc furnaces and there use for melting and treatment of these dusts are in the center of interest of this paper. The final conclusion gives an overview of possibilities for reduction of filter dusts in the liquid phase.

Jan 1, 2011

By Rodrigo Craig Cerello

The Brazilian economy has always presented a strong correlation with the mineral activity. Since colonization days, due to the territorial expansion caused by the explorers search for gold, mining in Brazil became a basic sector of national economy. Currently, the Brazilian mineral sector¹ estimates a 550% production increment (Figure 1A) in the last 10 years, reaching the US$ 50 billion value, reflecting the increased global demand for raw materials from mineral origin. According to the Brazilian Constitution², mineral resources belong to the Federal State and, consequently, their exploitation must be authorized, under penalty of engendering federal crime. Furthermore, activities of this nature are prone to cause environmental degradation such as, but not limited to, deforestation, pollution, soil deterioration and water contamination. The GPEMA represents the forensics group of the Brazilian Federal Police responsible for the technical analysis of traces related to crimes against the environment and consequently, illegal mining cases.

Aug 1, 2013

By Walter Valery, Sergio Vicuna, Roberto Valle, Hamer Arevalo, Ben Burger, Lui Vargas, Alex Jankovic, Jim Seidel, Eduardo Nozawa

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha’s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32’ x 32’ EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977

By Matt Schuett

Antamina Mine Facts • Surface Water Design Principles • Drainage Areas • SEDCAD Modeling • Impacted Runoff Collection • Clean Runoff Collection • System Flexibility • Outfall Construction

May 1, 2004