Search Documents

Gold recovered on the strikes at the Central Norseman mill, Norseman, Western Australia, has an approximate assay fineness of 850. Bullion recovered from the cyanide plant at the mine is of much lower value, and occasionally its assay fineness has been as low as 250. This indicates either that the fine gold particles in the ore consist of an alloy richer in silver than the coarse particles or else that a silver mineral, as well as the gold, is dissolved by the cyanide solutions.It had been observed at the mine that the amount of silver in the bullion appeared to increase when galena appeared to be more abundant in the stoped ore. Interest was, therefore, attached to the possible occurrence of a silver mineral associated with galena and, at the same time, soluble in cyanide.Four specimens of ore from different horizons in the mine were collected by the mine staff for examination as to whether any marked difference in the fineness of gold was apparent on a polished surface and for determination of the silver minerals. As the Norseman ore-body is a quartz reef containing a very small percentage of sulphide, the specimens were selected either because they cont;:lined free gold or because they were, relatively rich in sulphides. They were obtained from the following localities at the Phoenix shaft.1. Level 16, section 28.2. Level 16, section 31.3. Level 8, section 31.4. Level 14, section 38.Specimens Nos. 1 and 2 were thus obtained from different positions at the same mining horizon, while specimens Nos 2 and 3 were obtained from different levels in the same vertical section of the mine.All the specimens consist of quartz characterized by thin, discontinuous seams of sericite and the presence of a little ankerite. Gold and sulphides tend to be localized along these seams, but particles of gold and sulphides are also scattered throughout areas of white quartz. This scattered distribution of the sulphides in relatively wide areas of quartz has involved the preparation of two or more polished sections from each specimen.The outcome of the microscopical examination of these specimens has been to determine that there is no appreciable variation in the colour of the polished particles of gold and, therefore, no marked difference in the amount of silver alloyed with the coarse and fine particles. The presence of small quantities of the tellurides sylvanite, hessite and altaite has been revealed, and found to vary in abundance with the abundance of galena.

Jan 1, 1944

By Q Johnston

Since its inception in 1990, improved metallurgical processing technologies, coupled with mine planning enhancements and improved geological knowledge, have sequentially enabled better efficiencies and economies of scale at the Macraes Gold Project. Over a period of 11 years, processing enhancements have been achieved by: +        increasing mill throughput, from one million tonnes per year, to current throughput of 3.9 million tonnes per year; +        improving recovery rates, from 70 % to approx 84 %; and +        performance enhancement through innovation, eg the use of kerosene to combat ClL pregrobbing. Future processing improvements have been identified in optimising the ore feed and processing flowsheet. The introduction of the autoclave has transformed the process flow form a traditional 'mill headgrade and tonnes milled' operation, to a 'sulphur/gold ratio and sulphur tonnes oxidised' operation.

Jan 1, 2001

The use of walk-through inspections, approvals and ad hoc investigations to ensure risk is kept within acceptable levels is reaching its limits of effectiveness. Further improvement in occupational health and safety requires a systems approach, and the use of Quality Management principles is an obvious basis for this. SafeGuard, a æbest practiceÆ model health and safety management system and audit criteria based on AS/NZS ISO 9001:1994, has been produced by the Department of Mines and Energy. Quality style audits of mine and quarry health and safety systems are now being carried out by the Inspectorate.

Jan 1, 1998

Many mining operations are uncertain of what costs they should be achieving. The majority of cost estimates are based on historical costs that have added contingency factors. Historical costs are a valuable source of information but a more precise costing method is necessary. There are several alternative methods for predicting costs. A methodology which provides the best indication of the achievable costs is one using a standard inventory list and a bill of quantities. The model is termed a Basic Principles model and addresses basic design principles and engineering constraints.

Jan 1, 1990

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010

The mining industry is the largest source of foreign income for South Africa. It is also the main source of employment in the country and, as an industry; it is also one of the largest. Due to the labour-intensive nature of the industry, labour costs in South African mines make up nearly 50 per cent of the total mine cost. It is thus imperative to have optimum labour planning and labour management systems in place.The focus of this study was to investigate current underground labour-planning models. It is shown that there are serious limitations. The range between an oversupply and undersupply of labour can be as high as ten per cent. A new system was therefore developed to ensure a constant labour demand and supply on a daily basis. One of the main objectives was to determine the existing labour supply range and thus the requirements to fill the undersupply. For this purpose, a specific methodology was designed to capture and process all the relevant information. Mine personnel was involved throughout the entire process to ensure ownership of the new model. This buy-in was achieved through planning workshops, interactive presentations and discussions. The improved frequency of daily blasts validated the new system by providing the correct amount and mix of the labour force. The new labour-planning model was then extended to optimise revenue. Implementation on a mine resulted in increased income of R95 million.

Dec 6, 2010

The Leigh Creek Coalfield is owned and operated by the Electricity Trust of South Australia to supply fuel to the Northern Power Station. To supply electricity at lowest cost, a costing and decision process that establishes the role of the Leigh Creek Coalfield in the overall system planning and operation is required. The costing is integrated in that it is based not just on a particular mine plan but on the wider need to supply a particular electrical demand. The detail costing has evolved over time from manual to main-frame computer to microcomputer techniques. Now there is a choice between fast consistent costs and a slower but more detailed and flexible costing.

Jan 1, 1990

By Giannini M

Of the optimization techniques proposed in determining the optimum open pit limits, dynamic programming and graph theory have proved most successful. However, publications on these two methods lack a certain amount of rigour and clarity in exposition. Certain ideas in the methods have been clarified and additional features introduced in order to make them more sensitive to practical applications. A case study in the form of an application of these ideas on data from a producing mine is presented and discussed.

Jan 1, 1986

By B Hartmann

In 2003, Independence Group NL purchased the Long Shaft Nickel Mine complex (Long) in Kambalda, Western Australia. Lightning Nickel, the nickel operating arm of Independence Group, faced considerable challenges operating the mine, with the most significant challenge being able to prove that the remnant ore at Long and the associated orebodies could be mined safely and efficiently. Given the seismic history at Long, the magnitude of these challenges could not be underestimated. In an effort to achieve 100 per cent extraction of the flatter orebodies, traditional methods such as room and pillar were dismissed. A method consisting of transverse sills, butting into each other was proposed. To stop fill material from the first sill rilling into the adjoining sill, it was proposed to backfill the sills with pumped cement fill. The capital cost of the fill plant was estimated to be in excess of $1.5 million and the cost for cement alone was $1.0 million per annum. Shotcrete was already an extremely useful tool in dealing with the widely variable stress environment, but was to be used in an innovative manner that would enable the full extraction of a tabular section of the Victor South orebody. A layer of shotcrete, approximately 100 mm thick, was to be sprayed on the up dip wall of the initial development sill. The sill was to be backfilled with ænormalÆ development waste and ætoppedÆ with sand backfill. The next sill, ie slightly up dip and alongside, was to be mined along the shotcrete boundary wall. With respect to wall stability, the premise was that the shotcrete wall would stay in place and prevent the backfill (development waste and sand) from rilling into the adjoining development. It was also proposed that any breaches of the shotcrete wall would be repaired using shotcrete before substantial inflow of backfill into the ænewÆ development. This paper describes the development and implementation of this mining method, as well as some of the associated financial aspects.

Jan 1, 2008

By J L. Mauk

The Sovereign, Jubilee, Scotia and Jasper Creek prospects occur in an area of ~3.0 km by 2.5 km (~7.5 km2) in the Hauraki goldfield. The prospects are hosted by andesitic to dacitic flows, autoclastic breccias and localised pyroclastic and air fall deposits. Jubilee and Sovereign prospects lie along the northern and southern parts of the Waitekauri Fault, respectively, whereas Scotia is located ~1 km to the E, and Jasper Creek a further ~1.2 km to the ENE. Wall rocks are typically intensely altered, although the degree of alteration becomes more variable east of Scotia and at Jasper Creek. Alteration minerals include quartz, adularia, albite, chlorite, pyrite, illite, interstratified illite-smectite, smectite and calcite. Several of these minerals have distributions that show distinct zonation with adularia most abundant at Sovereign and Jasper Creek, but restricted to shallow levels at Scotia. Illite occurs throughout Sovereign and Jubilee plus the western margin of Scotia where it grades into interstratified illite-smectite; smectite predominates at Jasper Creek. Veins are uncommon and typically narrow, but show distinct zonations. Quartz veins are more abundant at Sovereign and Jubilee, whereas calcite veins are more abundant at Scotia and Jasper Creek. Laumontite veins occur at Scotia, and rare clinoptilolite, mordenite and stilbite veinlets with calcite occur at Jasper Creek. Fluid inclusion in quartz and calcite homogenised between 141¦ to 272¦C and trapped a dilute solution with an apparent salinity of less than 2.6 weight percent NaCl equivalent. Homogenisation temperatures are hottest at Sovereign (average 241¦C) and Jubilee (average 239¦C), cooler at Scotia (average 204¦C) and coolest at Jasper Creek (average 162¦C). Calculated paleowater table elevations suggest the water table was 680 m to 750 m above sea level at Sovereign and Jubilee, 450 m at Scotia and 225 m at Jasper Creek. The current data suggest three scenarios that can explain why Sovereign and Jubilee are deep and hot, whereas Jasper Creek is cool, shallow and marginal; 1.   some or all of the prospects may represent separate overlapping hydrothermal system, 2.   a high-relief hydrothermal system on the side of volcano with an inclined water table and outflow towards Jasper Creek, and 3.   a low-relief hydrothermal system that has been either tilted or block faulted with greatest uplift and erosion to the west.

Jan 1, 2005

By Gale D. C, Giles D. E, James Parker A

A zinc-lead-iron sulphide concentrate from McArthur River can be leached at atmospheric pressure in aqueous solutions with HCI, FeCl3, CuCI2, HCl/02 HC1/02/ CuCI2, Cl2, and CI2/CuCI2 to extract >98 per cent zinc, >90 per cent silver, and <15 per cent iron in 1-7 h at 95°. Galena is more reactive than sphalerite and is converted to lead chloride. Except for leaching with HCI, elemental sulphur is the the main by-product of the leach with little or no sulphate ion detected. The rates and products of these reactions are compared. It is recommended that aqueous slurries of the concentrate (50 per cent w/v) are leached at atmospheric pressure with Cl2 in the presence of copper(II) chloride, which accelerates the extraction of zinc. Hydrochloric acid is a by-product which is consumed bYJeaction with fresh concentrate in air at 60°. Copper is subsequently stripped from the leach solution and recycled by reaction with fresh concentrate at 100°. The separation, recovery, and electrolysis of zinc and lead chloride is outlined since this process would produce Cl2 gas which can be recycled and used directly in the leaching stage.

Jan 1, 1976

The discussion in this paper centres on examples of mining that are drawn mainly from the coal mining industry. The intention is to review the opportunities that exist for incorporating environmental planning into mining industry practice in New Zealand. The coal mining examples serve to make some general points which have some application for many types of mining.

Jan 1, 1981

The modern Golden Cross mine entered the production phase in January 1992. The project is designed to produce over 100 000 oz/yr of gold and over 300 000 oz/yr of silver during a mine life of eight years. An open pit and an underground mine are operated producing around 850 000 t/yr of ore, to feed a conventional carbon-in-leach processing plant. Golden Cross is owned in joint venture by Coeur Gold New Zealand Limited (80%) and Viking Mining Company Limited (20 %).   Since the start of production several major aspects of the design have altered. The underground mine began as a mechanised cut and fill operation. The cut and fill stoping progresses in 3.3 m flatback lifts with maximum stoping width of 6 m. Where the ore zone is wider than 6 m a post pillar cut and fill method is used. In 1993 a new bench mining plan was introduced between the 270 and 260 levels. Flatbacking continued in the footwall drives in anticipation of variability of the ore width and orientation. The development of levels below the main service 200 level has indicated a possibility of bulk mining the ore block rather than flatbacks. This could lower mining costs but also introduce higher dilution rates. Development is in the advanced stages for trialing this method.

Jan 1, 1994

Alluvial gold mining in New Zealand and in particular on the West Coast underwent a renaissance during the early 1980's. This was based on two main factors: a) the sharp rise in the gold price b) the advent of the hydraulic excavator with which to mine the auriferous gravels. The scale of operations varies considerably. A small operation typically consisting of one or two people using an excavator to feed either a land based or pontoon mounted (floating) gold recovery unit, which will typically feature a rotary screen with or without a tailings stacker with the screened fines < 10 - 15 mm) fed over riflle tables. The largest screening plants of this type are operated by DML Resources in their Arahura and Mikonui mining operations where the plants have the capacity to screen up to 250 m3 of gravel per hour. These plants usually employ jigs and centrifugal concentrators for gold recovery. Unique amongst current operations is the Grey River Dredge, a bucket ladder dredge capable of processing 700 m3 per hour similar to those that operated earlier this century. Gold concentration is by a series of jigs. The number of plants operating in recent times peaked at around 130 in 1987 (coinciding with a nominal average gold price of $751) and since that time has steadily declined to 80 units in 1993 and about 45 - 50 units today. This cycle of rapid expansion and then steady decline has been repeated on the West Coast since the original gold discoveries in the mid nineteenth century.

Jan 1, 1996

My speech this morning is not a technical one, rather I will aim to tell you about the New Zealand Aluminium Smelters Limited and how I see it fitting into the Western World aluminium scene.

Jan 1, 1983

By H Susanto, N Belluz, D Flint, A Edw

The Deep Ore Zone (DOZ) is a block cave mining operation exploiting a diluted reserve of 131 million tonnes grading 1.06 per cent copper and 0.81 g/t gold in the lower portion of the Ertsberg East Skarn System (EESS). The EESS is a calcium-magnesium silicate skarn containing in excess of 250 million tonnes of copper-gold ore, located in the Ertsberg Mining District on the crest of the Jawawijaya mountain range in the highlands of Irian Jaya, Indonesia. The EESS was discovered in 1968 where it cropped out at an elevation of 4050 metres above sea level. The Ertsberg Mining District is underlain by siliclastic carbonate and siltstone formations of Jurassic to Tertiary age. The sediments have been folded and are cut by major bedding subparallel and crosscutting structures. Intrusion of a series of igneous bodies post-dates folding and faulting. These I-type intrusions are the source for the copper-gold mineralisation found in the Ertsberg Mining District. The EESS is hosted by carbonates of the Tertiary Waripi and Faumai Formations that have been altered to calcium-magnesium silicate skarn and is situated on the southern limb of a northwest-trending syncline. The EESS is an essentially vertical tabular body with a vertical extent of at least 1200 metres and a lateral extent of up to 1000 metres. The width of the EESS averages 200 metres and locally is in excess of 300 metres. The northeast (hangingwall) contact of the EESS is a skarn reaction front in sudden contact with barren marbles. This contact coincides with a zone of localised faulting and brecciation. The EESS is bounded to the southwest (footwall) by the Ertsberg Diorite, a 3.25 Ma old intrusive. The DOZ block cave operation extends from 3040 metres above sea level to a maximum of 3388 metres above sea level, has a length of 860 metres and a maximum width of 350 metres. The DOZ is a high temperature skarn with a prograde forsterite/diopside mineralogy whose protolith is the dolomitic Tertiary Waripi Formation. The principal retrograde alteration minerals include tremolite, actinolite, serpentine, talc and chlorite. Grade is highest where bornite occurs in large dense complex intergrowths with magnetite and anhydrite. Grade has been locally enhanced in the DOZ by a late-stage pyrite-chalcopyrite hydrothermal alteration event with associated brecciation. Ertsberg Diorite along the footwall of the skarn is also included in the reserve where it is mineralised endoskarn or has been mineralised by porphyrytic or late stage hydrothermal alteration. Formation of the EESS was initiated by contact metamorphism during the intrusion of the Ertsberg Diorite with later metasomatic alteration during both prograde and retrograde phases. The bulk of sulphide mineralisation formed late in the retrograde phase. The EESS is open along strike to the northwest and down-dip with on-going exploration of these areas. Current exploration is targeting both endoskarn and porphyry style alteration and mineralisation of the Ertsberg Diorite.

Jan 1, 1999

By S Telford, J Weir

Heathgate Resources Pty Ltd (Heathgate) operates the Beverley Uranium Mine in South Australia, located on the plains between the northern Flinders Ranges and Lake Frome some 600 km north of the state capital Adelaide. The uranium orebody exists in permeable sands within the confined, highly saline Beverley aquifer, approximately 125 m below the ground surface and the uranium is mined using in situ recovery (ISR) technology. The Beverley mine is a highly technologically advanced ISR mine and is operated in accordance with stringent safety and environmental standards. The mine is currently licensed to export 1500 t of uranium oxide (U3O8) per annum. This paper outlines the fundamental differences between ISR operations and the more traditional uranium production methods, such as agitation leaching and heap leaching, where the ore is removed from the deposit, stockpiled, crushed, milled and leached on the surface. Solids tailings from either the mill or the heap are finally deposited in a tailing storage facility. ISR mining differs from conventional mining because the ore remains in place underground (in situ) and the groundwater contained in the ore-bearing aquifer is utilised as the mining fluid. This is achieved by drilling into the deposit and installing wells for extracting and re-injecting the groundwater which is fortified with chemicals. The fortified groundwater (ie mining fluid) flows through the permeable sands containing the orebody, dissolving the uranium. The pregnant mining fluid is then collected and transferred to the recovery plant where the uranium is captured (on ion exchange (IX) resin in the case of Beverley). The barren mining fluid is then re-fortified and recycled to the wellfields. Once mining is completed in a wellfield, the surface infrastructure is relocated to a new wellfield, and the mined-out wellfield is rehabilitated to its original surface condition. A comparison of 'standard' hydrometallurgical plants, heap leach and ISR shows a number of key differences, such as the rate of leaching, the level of control available to the operators, and the type of contact/reaction that occurs. While limited in its applications, ISR mining has proven successful at Beverley and provides another mining and processing method for the production of uranium.

Jan 1, 2008

By B Belle

In a predrained gassy coalmine, ventilation control plays a secondary role to the longwall (LW) goaf drainage systems to safely manage panel return gas levels. Typically, the LW specific gas emission (SGE) estimation models provide anticipated goaf gas emissions and arriving at required gas drainage capacity for various coal production scenarios. A study comparing the various LW goaf gas hole spacing patterns with weekly production rates of up to 270 kt/w of an operating mine with high SGE rates (~20 m3/t) was carried out. The goaf capture efficiency of LW panels ranged from 64 per cent to 85 per cent. For the first time, gas content of upper seam data post LW retreat were used to verify the current SGE prediction models. This study has shown that an average of 50 m goaf spacing is optimal for management of high production retreat gassy LW panels in presence of multiple upper and lower seams with gas emission zone influence reaching up to 200 m above workings. Due to the horizontal stress direction related geotechnical issues, goaf hole failures just behind the LW face is a recurring challenge resulting in significant and immediate increase in LW panel return gas levels. This paper highlights the shortcomings of current SGE prediction models for goaf gas estimation, and evolution of 50 m goaf hole spacing embedded in design process in managing the LW tailgate gas levels.CITATION:Belle, B, 2017. Optimal goaf hole spacing in high production gassy Australian longwall mines – operational experiences, in Proceedings Australian Mine Vent Conference 2017, pp 15–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By K Nilsson, D Connelly

Troy Resources acquired the Karouni Gold Project in Guyana, South America in 2014 and immediately proceeded to a Pre-Feasibility Study and project implementation. The study considered two open pit mines feeding a conventional carbon in leach (CIL) gold plant with a capacity of 1Mtpa. The study assumed a total of 2.61 million tonnes of ore with an average grade of 3.84 g/t gold with a recovered gold production of 303,526 ounces over a three year mine life.The project development involved drilling metallurgical test holes, securing second-hand major pieces of equipment where suitable, and arranging shipping to Guyana. The remote location meant logistical considerations were paramount. The plant consists of conventional two-stage crushing with single stage ball milling and a gravity circuit. The tailings circuit includes DETOX.The extremely high rainfall presented challenges with water management and the necessity to dispose of clean water to the environment. The DETOX was also mandatory due to the highly sensitive environment and past history in the area. The criticality of this meant that in the design, any cyanide in the tailings would precipitate in a plant shutdown.Lessons were learned and the project has been both profitable and successful for Troy Resources in a new operating location. In addition, the project has created jobs, delivered royalties and brought new skills into an area where previously there was little current mining activity.CITATION:Nilsson, K and Connelly, D, 2015. Karouni Gold Project from drill core to commissioning, in Proceedings MetPlant 2015, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

IN this paper it is proposed to present certain features of operating practice at the Port Pirie works of The Broken Hill Associated Smelters Proprietary Limited, in the smelting in a blast furnace of lead ores carrying a high concentration of zinc.The subject matter selected for presentation is:(i) The effect of zinc on lead blast-furnace operations, together with an outline of the methods adopted in actual practice in dealing with the zinc problem.(2) Development of the height of tuyere above the bottom of the jacket, and the extension of the tapping interval and the combined effect of both factors upon the lead content of blast furnace slag.It will later be seen that one phase of the investigation carried out in connection with the effect of zinc on blast-furnace operations was largely responsible for the decision to increase to a marked degree the height of the tuyere above the bottom of the jacket.Due to this interdependence, it has been considered advisable to deal with the two features above mentioned.The high concentration of zinc in the lead-bearing materials smelted at Port Pirie has brought with it those troubles which are associated with zinc in the smelting operation.In the early stages of the history of The Broken Hill Associated Smelters Pty. Ltd. the trend towards increasing cost for labour, fuel, and stores, etc., rendered it necessary to increase the lead content of the charge, and reduce to a minimum the quantity of barren flux used.

Jan 1, 1931