Search Documents

Teller Underground Mine was established to extract ore from the Middle Vale Reef located on the eastern flank of Telfer Main Dome.The mine is located below a 150 m deep open pit operation. The ore body is shallow dipping highly structured, and is a main aquifer in quite difficult ground conditions.In respect of these conditions it was determined to access the orebody using an adaptation of coal mining and hard rock mining methods, with support being achieved using a combination of island pillars, rock bolts and timber stalls.The paper will describe these methods in more detail, then discuss the successes and failures of these methods when put into practice. As well, it will detail several factors whose influences were found to be greater than previously expected and stress the importance of good geotechnical advice.

Jan 1, 1993

By Stein A

The general mechanism of recrystallisation for cold worked metal is well established, and need be only briefly summarised with a few references to recent articles which clarify minor points. The types of extension, whether by stretching, drawing, hammering, rolling, etc., do not alter the general principles (1), although quantitative results may differ somewhat, particularly with regard to differences between the surface and interior of samples.These principles can be summarised as follows: The first stage in annealing is a recovery (sometimes known as relaxation) of physical properties such as hardness, elongation, etc., without any appearance of recrystallisation; the second stage involves a further alteration in physical properties, accompanying the formation of new recrystallised grains which replace the original structure; a possible third stage involves an increase in the grain size of the completely recrystallised structure by absorption of smaller grains by larger ones. These three stages will be referred to as recovery, recrystallisation, and grain growth. Depending on conditions, the three stages may be clearly marked or may occur more or less simultaneously.For a given annealing temperature, cold deformations below a certain amount fail to give recrystallisation, and the final structure consists of the original grains which have recovered and possibly become more equiaxed. When a certain deformation, critical for that annealing temperature, is given, recrystallisation can occur, and will give the maximum recrystallised grain size.Increasing deformations beyond this give progressively smaller grain sizes.For each material there is a minimum recrystallisation temperature, below which recrystallisation will not occur whatever the deformation or time of annealing. For a given deformation there is a temperature, critical for that deformation, below which recrystallisation will not occur, and above which it will take place with increasing rapidity.

Jan 1, 1947

The Circum-Pacific is defined to include back arcs and continental areas of volcanism. Volcanoes must be regarded as dormant, if the time since their last eruption is less than about ten times the average interval between eruptions, even if they have not erupted for tens of thousands of years or longer. It is important to establish a complete history, over as long a period as possible, for varying volumes of eruptions. In order to assess risk, the average interval between eruptions should be calculated for each range of erupted vo4ume~, in orders of magnitude from about 10 m up to the maximum volume possible at each volcano. Eruptions are considered to consist of individual explosions, and are grouped into eruptive sequences, with the sequences grouped into overall cycles of activity. Frequency of eruption versus volume erupted is a linear relationship for most andesitic and basaltic volcanoes, but is often bimodal at rhyolitic volcanoes, 3 with a slower eruption rate above about 10 km. Worldwide, during the last 7000 years, there have been three known e~uptions with volumes of ejecta of > 100 km , a9d, since 1638 A.D., 7 with volumes > 10 km , and 48 with volumes > 1 km . Average recurrence intervals are about 71 years for eruptions of > 20 km , 39 years for those of > 10 km , and 7 years for those of > 1 km . Rough esti- mates can be made for larger volumes erupted. Mean intervals in the Circum-Pacific are about twice the length of those for the world as a whole. During the last 400 years, about 61% of the world's eruptions of > 1 km3 have taken place in this region.

Jan 1, 1987

IT is most remarkable and valuable property of mediurn and high carbon steels that they should be so susceptible to heat treatment, the wide range of variability in tenacity, ductility, etc, due to the normal influence of the carbon in the untreated material being enormously inereased thereby.The physical properties of steel and other metals are much more closely related to their structure than to their ultimate analysis.For instance, we may by chemical analysis determine the carbon content of a steel to be 0.5% ; but this information alone is insufficient to enable us to say what are the physical properties of the metal.Such a steel may possess 11 tensile strength of anything from 35 tons per sq. in., with much ductility, up to 80 tons per sq. in., with practically no ductility, according to its heat treatment. A microscopie examination, on the other hand, would show the structural composition of the steel, from which its physical properties could be approximately deduced. From this it will readily be understood that the microscope has played an important part in the development of modern rnetallurgy, and to-day it is in daily use for the examination of metals and alloys in the laboratories of most works dealing with the rnanufaeture and working of metals.THE IRON-IRON CARBIDE EQUILIBRIUMTo understand fully the mode of occurrcnce of the different constituents of a knowledge of the Iron-Iron Carbide equilibrium diagram (Fig. I) is essential to heat-treat steel successfully and to interpret microstructures correctly such a knowledge isabsolutely indispensable.A portion of the Iron-Iron Carbide Diagram, dealing with steels below 1000 and containing up to 1 carbon is given below.It should be noted that the diagram deals entirely with pure carbon steels, and does not indicate the influence of the usual so-ealled "impurities" present in all commereial carbon steels...

Jan 1, 1926

This paper reviews the geochemistry of weathered nickeliferous sulphidic and lateritic profiles, the supergene behaviour of nickel and ore-associated elements, and their implications for exploration in an attempt to distinguish between barren and mineralised nickeliferous profiles. Nickel is an abundant accessory element in ultramafic rocks with background concentrations in some units up to 0.25 weight per cent. Ore-grades in fresh rock are mostly associated with massive and disseminated sulphide zones within magnesium-rich layered ultramafic sequences. In lateritic weathered terrain, nickel is also concentrated in the regolith profile. This process not only upgrades nickel in the gossanous weathered product of sulphidic deposits, but for sub-economic sulphide zones and some ultramafic rocks, is sufficient to result in a supergene resource. Ore-grade accumulations of nickel in regolith after sulphide-poor ultramafic rocks are referred to as lateritic deposits. Nickel sulphide zones and their ferruginous weathering products are collectively referred to as sulphidic deposits and are the major source of nickel in Western Australia. Mineral exploration in the Yilgam Block is hampered by deep lateritic weathered profiles (eg Butt and Sheppy, 1975; Smith, 1977; 1982). During the nickel boom of 1967 - 1972, most discoveries resulted from the location of outcropping nickeliferous gossan and ironstone. Exposed ultramafic terrain with nickel sulphide potential were explored intensively, mostly by gossan and soil sampling. However, up to 85 per cent of the area of the Yilgarn Block is buried by transported regolith. In these covered areas, barren and mineralised rock responses at the surface are similar and soil sampling produced unreliable results due to many false anomalies. A statistical, multi-element approach to regional geochemical exploration has evolved. Potential trace element indicators investigated, include Co, Cr, Cu, Ir, Mn, Pb, Pd, Pt, Sc, Se, and Zn. In recent years, trace element ratios have also been tested with varying degrees of Success.

Jan 1, 1996

The extraction of the values from gold bearing clay or clayey ores has always presented difficulties. A description of the successful operation of a mill working on material of this nature is here given in the hope that it will be of interest to mining engineers and metallurgists, particularly as the ore body referred to has been worked out. The methods finally adopted were evolved at the mill after the failure of 3: plant specially designed in England and sent out to New Guinea to cope with the clay by the old principle of calcining to brick followed by crushing and cyanidation. A description is given of the direct cyanidation of run of mine ore in '90 ton vats; which was finally adopted after a great deal of study and experiment. Mention is also made of the method of removing overburden in the open cut and the mining and transport of the ore from the open cut to the mill. The purpose of the paper is to record these matters while the information is still available. . .DESCRIPTION OF THE ORE BODYThe values occurred in a flat-lying lode which had slipped about half a mile down the mountain side and had come to rest in the nearly horizontal position in which it was found and worked. The thickness of the deposit varied from a maximum of about 25 ft. at the northern end to about 10 ft. at the southern end. The ore body was capped with an overburden of decomposed breccia and porphyry of variable thickness the maximum being about 65 ft. The underlying rock, or the footwaIJ of .the flat ore body was breccia locallyknown as blue breccia.

Jan 1, 1951

By M S. Gallagher

In todayÆs high tech world, systems are getting bigger, faster, better. To remain at the leading edge, in any business, depends on accuratebut flexible design thereby allowing operational managers to providealternatives to improve their operations. The ultimate goal is to deliver to plan, with optimum economics. Mining is no different; with falling prices and escalating costs,improved margins become the focal objective. There are many ways toachieve this, ranging from operational efficiency improvements through production scenarios to planning initiatives. Of all, planning usually receives the least attention, yet it is the area of most influence on the Net Present Value (NPV) of the reserve. With computer technology, numerous concepts and iterations are possible thereby closing the gap between optimal and actual design. This paper discusses the application of the split shell design at the De Beers Venetia open pit in South Africa.

Jan 1, 2001

By Restarick CJ

Plant data are presented which indicate a relationship between flotation rate constants and pulp density in zinc cleaning circuits at Broken Hill. The data were obtained from down the bank sampling of cleaner and recleaner banks at North Broken Hill and New Broken Hill Consolidated Concentrators. It was found that, under normal plant operation, flotation rate constants increased at the lower pulp densities existing in the later cells of cleaner banks. The addition of dilution water to the feed to the bank increased flotation rate constants, thereby confirming the relationship. It is shown that the relationship between flotation rate constant and pulp density is size dependent, being most pronounced for larger sized particles. In contrast, the effect is not markedly dependent upon mineral type. Possible consequences of this relationship for control of cleaner operation are discussed with the aid of some simulated results.

Jan 1, 1978

By Tran T, Young D

During the processing of gold, effluents that are discharged into the tailing dams contain free cyanide, metal cyanide complexes of zinc, copper, iron, etc and their oxidised products such as ammonia, cyanate and thiocyanate. A knowledge of how different cyanides behave in the solution is vital to metallurgists working in the area of cyanide waste treatment. Although the free cyanide ion is not stable in aqueous solutions and is expected to degrade in a natural environment by atmospheric oxidation, the metal cyanide complexes, especially of iron, are very stable. The CHEMIX program from the THERMODATA package, developed by the CSIRO Division of Mineral Products, was used to evaluate various copper-cyanide and iron-cyanide systems. The simulation of these systems show how the free cyanide and cyanide complexes behave at different conditions of solution composition and acidity (pH).

Jan 1, 1991

By Miyashita T, Yamamoto R, Kishimoto s

Following considerations of the effect of furnace size on pressure loss, pressure loss in front of tuyeres, gas flow in the lower parts of the furnace, the distribution of the burden and the gas flow in large blast furnaces is examined with particular reference to the burden distribution at the throat and the gas flow at high production rates. Improvement of gas flow is related to application of super-high top pressure and the use of moveable armour. A brief description of the NKK type moveable armour is given and its use in controlling the gas flow outlined. The operating results under controlled gas flow show an increase in production of Fukuyama No. 5 BF from 9,200 tpd to 11,000 tpd with a decrease in the fuel rate from 490 kg/thm to 460 kg/thm.

Jan 1, 1975

The types of risk to mining projects using environmental protection as justification are examined. In Australia, Governments, whether Federal or State, enforce environmental legislation. The way they do This has an impact on the risk to a project. This is discussed and examples are taken from the Northern Territory uranium industry. Special reference is made to mine closures where the roles are not yet entrenched.

Jan 1, 1994

'Industrial Minerals - their mining and use in New Zealand' is the theme of the 1978 Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy. This paper describes the use of phosphate rock, sulphur and potassium chloride (potash) - three industrial minerals which have enabled the farmers of New Zealand to increase production to current levels. The growth of imports of these raw materials for the New Zealand fertiliser industry is well documented in NZ Fertiliser Statistics 1977. This is the most recent of the Ministry of Agriculture and Fisheries annual publications on this Subject prepared from the detailed returns of fertiliser manufacture and sales from each fertiliser works. There are now 12 of these works in New Zealand one of the most recently established being in Whangarie where this conference is being held. Its capacity to manufacture superphosphate will shortly be 300 000 tonnes twice that when it opened late in 1964. New grinding and manufacturing equipment comes on stream early in 1979. This paper illustrates the interdependence of two primary industries, agriculture and mining. New Zealand's economy in the foreseeable future will be based on agriculture so that our standard of living is dependent on the overseas prices and freight costs of the bulk raw materials from which our fertilisers are made. For the year ended 31 March 1978 New Zealand's total exports were $3395 million, of this total $2413 million (71%) came from the products of pastoral agriculture (wheat, wool, dairy and other animal products), $291 million from forest products and $501 (15%) from manufactured exports. Approximately half of the pastoral receipts can be attributed to the fertilisers applied at a total cost of about $200 million including subsidy.

Jan 1, 1978

Anyone who has driven backwards using only their rear view mirrors knows how difficult it is to avoid spinning the steering wheel the wrong way. So why run your mine that way? Traditionally Reconciliation has focused on the past performance of the mine. In this paper we make a case for Prognostication û the act of forecasting or predicting something in the future from present indications or signs. Reconciliation is a common activity carried out at most mines around the world. Countless geologists and engineers spend hours poised in front of spreadsheets diligently comparing how their resource/reserve model, grade control, and survey pick ups compare to what was actually produced. The result is usually a group of factors, which are applied to future estimates in an attempt to better predict how the operation may perform. Unfortunately, if the road ahead isnÆt the same as what you have just been down, youÆll be æoff-roadingÆ in no time! An alternative is to constantly collect and analyse key measurements that are used to calibrate critical estimates in an iterative process. When variations occur, they are analysed and corrective action is taken to ensure the estimates and measurements realign. In this way the estimates become forecasts and can then form the basis for decision making to ensure that what does happen in the future will match the plan or schedule. By automating this process, some mines have been able to be proactive on a daily basis in order to improve the overall performance of the operation. This paper outlines the key estimates and measurements used for reconciliation, details the characteristics of an automated web based information management system to facilitate the process and provides some insights about how mining operations might move beyond reconciliation.

Jan 1, 2003

By G MacSporran, I Sheppard

The practical application of LaneÆs theory on optimum cut-off grade policy has to date proved difficult for selective stoping in large-scale underground mining. The key to determining an optimum cut-off grade is the ability to rapidly perform complex mine layout designs combined with rapid output of multiple potential schedules. This paper describes aspects of the detailed investigation into estimating a practical static cut-off grade for the two main orebodies in Mount Isa MineÆs Enterprise Mine. Rule based automated scheduling software was used to evaluate thirteen different stoping layouts (including design infrastructure and capital development) of the Enterprise MineÆs two main orebodies, with over 200 schedules generated. The investigation illustrates the application of commercially available software to solve the problems of generating multiple cut-off grade stope designs and achieving the otherwise insurmountable task of rapidly generating and valuing multiple scenarios for each stoping layout. Each scenario was evaluated using modelled net cash flows of the mining, concentrating and smelting operations of the company and calculating NPV. The cut-off grade for each orebody was selected based on the cut-off grade that achieved maximum NPV û with an appropriate production rate. Underground mine scheduling is a complex task involving the adherence to a number of simple scheduling rules and the balancing of several competing drivers. The study also found that: while each scheduling rule itself is simple, the compounding complexities of their interaction preclude manual scheduling from being a realistic option. there is a maximum sustainable rate of production possible for any given stoping layout, and that the actual maximum production rate is also a function of the required number of years of sustainable production. the optimal cut-off grade was different for each orebody û a recognition of the impact of the different characteristics of each orebody.

Jan 1, 2003

By S Jahanshahi, T Norgate

In single stage copper making appreciable amounts of copper report to the slag phase. Various strategies are available to minimise copper losses to the slag. However a slag treatment stage is likely to be required in an economically viable process. A number of slag treatment process options are available and include: flotation, leaching and thermal reduction. In the design of an industrial process some type of economic as well as technical analysis of these options will be required. In this paper an outline of the techno-economic analysis procedure used to design a single stage copper making process is presented. The calculated operating and capital costs of industrial copper making processes are compared and used to determine the optimum single stage copper making flowsheet. The most economic slag treatment options is flotation of slags containing low amounts of copper.

Jan 1, 2000

By M A. Ward

On 23 May 1977 the Hon Mr George Gair announced an amalgamation of the present Ministry of Energy Resources, the New Zealand Electricity Department and the Mines Department. Hopefully it will prove to be the solution of many national problems in energy planning and policy making, in energy distribution and use, and energy discovery and production. The name of this new giant is the Ministry of Energy which gives a firm indication of its future direction. For those amongst us involved with mineral energy resources the establishment of this new department must be encouraging. For those amongst us who are involved in non-energy side of the mineral industry it is the very opposite. The loss of the Mines Department a year short of its centenary is a loss for the mineral industry without a doubt - but how much of a loss?

Jan 1, 1977

The A J Parker Cooperative Research Centre for Hydrometallurgy has recently been established by a major grant from the Australian Commonwealth Government. The participating institutions in this centre are the CSIRO Division of Mineral Products, Curtin University of Technology, Murdoch University and the Chemistry Centre (WA). The Australian Mineral Industries Research Association is also a partner. Information is presented about the research activities of the Parker Centre, which are focussed on the solid/solution interface. Three research programs have been established in the areas of leaching, precipitation and surface processes (adsorption). The initial projects within these three programs are described. Details are also given of the Centre's education program which include honours degree training, masters and doctoral degrees by research, a masters degree by course work and workshops. The importance of collaboration with industry to the successful operation of the centre is stressed.

Jan 1, 1992

The sudden. explosion of relatively inexpensive digital process control computers has accelerated interest in the possibilities of economic savings by their use. In particular the metalliferous industries have shown that they are willing and capable 6f grasping this new technology and putting it to good use. These industries have a number of problems which need special attention. In many cases the process is difficult to measure and a reaction is often controlled by measuring a secondary effect, computing its relationship to the reaction and then applying the necessary corrective action. This creates problems in building the process model, designing the computer to process interface and in the subsequent system development. Environmentally the metalliferous industries create conditions which severely test sophisticated electronic equipment. Care taken in locating and housing this equipment is a major factor in ensuring reliability in Operation.

Jan 1, 1977

The behavior of a curved wall under earth pressures for a horseshoe shaped tunnel lining is considered to be closely related to the beha vior of a vertical beam with variable flexural sti-"ness on an elastic foundation. In stress analysis an approximate method which divides the axis of the tunnel lining into small finite lengths and replaces the integrals by summation is usually adopted. this method is extremely complicated and tedious. However the variations of the moment of inertia from point to point along the wall axis can be expressed by a power function inversely .eith the distance from the ll )ottom and the analytical method can still used. The equations for the calculation of deflection, rotation, bending moment, shearing urce, and soil reaction of the curved wall are derived in nondimensional forms in this paper.

Jan 1, 1987

By J G. Petrie, H von Blottnitz

The selection and design of process options to deliver outcomes consistent with sustainable development requires simultaneous consideration of multiple objectives, within a climate of uncertainty û including the environmental and social aspects of technology management in addition to the technical and economic aspects of such. An issue of particular relevance in primary metal production is the deportment of minor and trace components within orebodies, products and wastes and the implications of such deportment for eco-efficiency û in particular, the long-term environmental impact of solid waste management practices. The identification of opportunities to enhance recovery of valuable by-products and simultaneously improve the environmental acceptability of final waste output requires a clear understanding of the distribution of the relevant ore components, which results from the choice of processing route and unit operation efficiency. This is challenging, given that process streams generated during primary metal production are generally poorly characterised and the behaviour and deportment of trace to minor and trace components is not well understood. This paper demonstrates how current data gaps and inconsistencies can be systematically addressed through the meaningful reconciliation of empirical plant data with a fundamental understanding of the mechanisms and parameters influencing element behaviour and deportment during the formation and subsequent beneficiation of mineral ore deposits. On this basis, quantitative distribution data and a comprehensive and comprehensible inventory of unit process inputs and outputs as a function of ore compositions and processing technology options can be generated, which is consistent with early design stage information requirements, both in terms of detail and accuracy, ie is æfirst-orderÆ in nature. This predictive approach to element distribution during primary metal production provides decision-makers with key information in the early design stages of a project (in terms of developing processes within the context of sustainability), whilst simultaneously guiding further data collection and environmental impact prediction studies.

Jan 1, 2006