Search Documents

By B Leisemann, M Watkinson

Coal augering is an ideal method for recovering coal from the highwalls of open cut coalmines. Coal augering is a simple process whereby additional flights are added to the auger cutting head and auger holes are drilled at 1.9 m diameter up to 200 metres deep. Traditional monitoring was located at the mouth of the hole and if methane was encountered above two per cent, inert gas was delivered into the mouth of the hole to deplete the oxygen content at the auger cutting head below 12 per cent. The auger operator was asked the question ‘how do you know that this is the case?’ Trials were undertaken to prove that the oxygen content at the cutting head did drop below 12 per cent (the lowest limit for methane to ignite, also known as the oxygen nose point). Initial trials showed that the oxygen content in the mouth of the hole did not drop below 12 per cent and modifications were made to hold the inert gases in the mouth of the hole so that the auger flights could take this inert gas into the hole. In-hole monitoring, after completion of mining and after extracting the auger flights, showed that the atmosphere quickly returned to fresh air. In-hole monitoring was also tried during the augering process and yielded valuable results. This paper will discuss the results of the monitoring, information on the gas results obtained and the methodologies used to optimise the oxygen content at the auger face.CITATION:Watkinson, M and Leisemann, B, 2017. Inertisation of coal augering holes, in Proceedings Australian Mine Vent Conference 2017, pp 293–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Two small coral islands in the Pacific Ocean, situated close under the equator, and formerly classed among the Line Islands, have, during the last three or four years risen into prominence owing to the valuable deposits of phosphate of lime discovered on them.The deposits of Ocean and Pleasant Islands are under the control of the Pacific Islands Company (1902) Limited, of London and, Sydney, and the high grade of the phosphate, together with the exceptionally favourable facilities for mining this mineral, of which there are several millions of tons on these islands, give this company advantages which enable them to command the Australian and New Zealand markets, and also to make large contracts with Japan and other countries. Both islands, as far as surface indications are concerned, are entirely constructed of coral, with phosphate on the top from the highest points to the present sea level, there being no sign of volcanic rocks, with the exception of a few pieces of drift pumice on the coast.Banaba (Paanopa according to. the Admiralty charts), also known as Ocean Island, was discovered in 1804. It is situated in lat. 0° 52" S. and long. 169P 3[)" E.

Jan 1, 1904

The author summarizes and extends the relevant results of papers previously published by various authors and presents these results in chart form. The charts are used to demonstrate the theory on a hypothetical mine.INTRODUCTIONRecently a series of articles have dealt with leakage in a mine ventilation system and the problem of its reduction.Theories were developed by Peascod and Keane (1955) for the combined effect of flow in the airways and leakage through the porous barrier between the intake and return of an ideal mine. Later Keane and Peascoa. (1956) extended these ideas to the use of an underground booster fan in increasing the face ventilation and showed how to determine the water gauge and location of the most efficient underground fan.These articles were based on the assumption that Atkin:son's formula:P = R Q2 (1)gave the relation between the pressure drop P lb'/sq. ft., the quantity, Q kilocusecs, flowing in the mine airways and the total resistance, R Atkinsons, to air flow offered by the mine roadway. An Atkinson is defined as a resistance such that 1 kilocusec of air flows due to a pressure drop of 1Ib.jsq. ft. However for conditions prevailing in most mines a more :appropriate relation is that postulated by Reynolds and others (Lamb, 1953) :P=R Qn (2)where n has some value slightly less than 2. It should be noted that Atkinsons may not be used as units when n is not equal to 2.

Jan 1, 1958

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950's, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

By G Veillette, B Parker, S Hart

This paper provides a history of the challenges that were experienced while treating both the clayey oxide gold ores and the supergene copper-gold ores at the Boddington Gold Mine during the period 1989 to 2001. However the bigger challenge was to find a process flow sheet that would allow the economic treatment of the large low-grade competent gold-copper resource that underlies the oxide and supergene gold resource. Metallurgical test work and engineering studies on this resource started in the mid 1990s and culminated in the approval in 2006 of the 35 Mtpa Boddington Expansion Project to treat this material. The process flow sheet provides the basis of an energy efficient comminution circuit that includes high pressure grinding rolls and a treatment circuit with gravity separation, flash and conventional flotation to produce a precious metal low-grade copper concentrate followed by cyanide leaching of the rougher-scavenger and cleaner tailings streams. The treatment circuit allows maximum removal of copper minerals prior to cyanide leaching and so provides an environmentally responsible tailings disposal circuit.

Jan 1, 2007

The Golden Ridges Mine, one of the properties of New Guinea Goldfields Limited, is situated on the right bank of Nami Creek, not far from the township of Wau, in the Territory of New Guinea.The property is somewhat unique, in that the goldbearing ore-body occurs in the form of a flat seam-like deposit lying on a volcanic breccia, and covered with a mantle of overburden of decomposed porphyry. The overburden varies in thickness up to a maximum of about 65 ft.The ratio of overburden to ore is about 3 to 1. The practice developed is to strip the overburden by hydraulicking, and to mine the exposed ore under open-cut conditions, blasting to a vertical face, and using electrically operated scraper hoists for conveying the broken ore to the mill bins.The stripping of the overburden involves the boring of well-drill holes, blasting the holes and then hydraulicking the shattered material.

Jan 1, 1934

The limit of pressure to which an underground dam may with safety be subjected, is a question that-as far as the writer knows has not received the same attention from authorities on engineering construction, or practical mining, that has been accorded to questions on which the design and strength of other structures or machines in connection with a mine are based. That dams may, under certain conditions, be constructed to resist water under great pressure is a known fact. But the difficulty of demonstrating beforehand that any proposed structure of this kind will withstand the pressure and be effective is, owing to the indeterminate nature of some of the risks to be provided against, very great. In the present state of our knowledge it may almost be laid down as a rule, that a dam of this kind should not be undertaken where grave consequences would attend failure until experience of structures where the physical conditions are similar, but where there are no such risks, has given assurance that such work would stand.In Mines and Minerals for May, 1900, there is published a paper by Mr. James McNaughton describing the construction of three underground dams in the iron mining district of Michigan.The first of these was put in to hold back a flow of 750 gallons per minute, which when pent up created a pressure of 276 pounds per square inch, showing that the height of the sustained column was about 635 ·feet. The hole through which the water issued was in the bottom of the cross cut it was enlarged by removing all loose rock for a depth of 18 ft...

Jan 1, 1901

This Institute, by nature of its charter, draws on various persons in the mining and metallurgical world of Australasia for its President from year to year, and consequently when the presidential address is given by one of these people the topic. which they generally select is a topic to which they are accustomed and on which they are able to speak with authority.As most of you know, my prime object in life has been concerned with steelmaking, so tonight you can steel yourself to the thought that you are going to be spoken to about steelmaking.Even if that were not the case, and were I not particularly interested in steelmaking, I think it would be appropriate to look at steelmaking in a broad sense on a basis of pure metallurgical interest, because the steel industry is going through as big a revolution today as it went through something over one hundred years ago when Bessemer made a theory become a fact.Bessemer, and as the Americans prefer to think Kelly, separately conceived the idea of blowing cold air through molten pig iron, and, contrary to the then general belief, this did not result in cooling of the metal but succeeded rather in heating it, and in burning out of the rather crude pig iron the impurities which prevented it from becoming a ductile metal.For many years before this, steel had been made in a very small painstaking way by what was known as the crucible process. Benjamin Huntsman is credited with having developed the crucible steel making process to a stage where it could make a reliable and trustworthy product, but he...

Jan 1, 1961

This article attempts to outline essential features of the Mount Isa ore deposit, to reveal the agencies thought to be responsible for its localization, and to describe methods used for obtaining and applying geological data on a commercial basis. Structural features are emphasized because they have proved the most useful agencies to date in searching for ore. Vertical depth, horizontal width and stratigraphic thickness are used throughout the article, and quantities are quoted in long tons.THE DEPOSITA width of more than two miles of evenly bedded shale of the Mount Isa series (upper pre-Cambrian) lies sandwiched conformably between quartzites. The series strikes N.S. and dips approximately 60° W. Shale is unaltered...Important geological work has been carried out by the Queensland Geological Survey, chiefly by Mr. S. R. L. Shepherd, in co-operation with the Geological Department of Mount Isa Mines Limited. Selected references are The Queensland Government Mining Journal for December, 1931, January, 1932 (Rio Grande Lode); December, 19B2 (Black Rock Lode); October, 1933 (General structure); October, 1936 (Mount Isa Lode).

Jan 1, 1939

The reactions between molten aluminium and cryoIite have been determined from a material balance of all components involved in the process. The interpretation of results were supported by x-ray diffraction studies of the evolved vapours, quenched electrolyte samples, and side-reaction products.The most important reaction involves the formation of both Na2F (sodium subfluoride) and chiolite in the fused electrolyte. The Na2F accelerates vaporization of the melt. Some AIF (aluminium monofluoride) may also be formed but the proportion of this is much less than for the former subvalent compound.

Jan 1, 1968

By P Duplancic and C R Lilley, R Hudson, D Beck

For deep block and panel caving mines, undercut or extraction level instability can have as much impact on overall recovery as underbreak or the premature ingress of waste. If the area of the mine affected by excessive convergence is small, recovery is usually possible. However, there are several examples of entire blocks that were abandoned prematurely due to footprint collapse. Clearly, such global instability has a major impact on recovery and must be avoided – this is one of the essential tasks for the design team.The design problem is complex. The planning engineer must ensure that the footprint has sufficient capacity to withstand the maturing loads in the cave, accounting for the effects of stress path, geological structures and the rock mass conditions. These are often uncertain and only sometimes quantified.The demand on the footprint will also be influenced by decisions and actions taken during production, especially related to draw, which can worsen a developing problem. Perhaps most importantly, the design decisions that favour stability and lead to lower deformation also negatively impact on idealised cave flow. Many engineers aim to minimise the size of extraction level pillars, to improve theoretical future resource recovery but in fact this can reduce recovery if widespread deformation ensues due to the undersized pillars.In 2014, PT Freeport Indonesia undertook detailed numerical analysis to quantify the effects of variability in rock mass conditions and geological structure on overall footprint performance. The analysis accounted for a range of stress paths and maturing cave loading scenarios sourced from a calibrated whole-of-cave deformation-flow model. The intent was to replicate some of the diversity and distribution of pillar deformation outcomes that may be seen in practice at Freeport.The discontinuum finite element analysis was able to replicate damage localisation around persistent structures, a realistic distribution of drive deformation and show how small areas of instability can evolve into major problems if poorly managed. The limits of pillar size and ground support as solutions to a number of different instability problems was also investigated, showing that pillar size alone was not a sufficient remedy for all adverse circumstances.In this paper, we describe the workflow for numerical analysis of footprint deformation. We discuss the compromises and considerations for balancing the sometimes competing needs for efficient extraction levels pillars, ground support and prudent draw strategy.CITATION:Beck, D, Hudson, R, Wilson, A D, Duplancic, P and Lilley, C R, 2016. An investigation of factors affecting the long-term reliability of extraction level pillars in deep block and panel caves, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

THE ore treated is almost pure copper pyrites (chalcopyrite) in a gangue of quartz and quartz-felsite. Very little free iron sulphide (pyrite) occurs, and at the time of the erection of the flotation plant the stopes in the oxidized zone had been almostentirely depleted. This zone only extends to a shallow depth, and, below the l00-ft. level, the sulphide for the most part is clean and bright but in the crushed and brecciated parts of the ore channel, where surface water has circulated freely, the gangue is decomposed and kaolinized, and the copper sulphide badly tarnished. This class of ore gave considerable trouble at the mill, but unfortunately, was very limited in quantity. A sample of rich ore assayed-Copper, 21.2 %; iron, 24:.3 %; silica, 28.9 %; sulphur, 25.1%.The concentration in the original mill was effected by handpicking, jigging, and tabling. A considerable portion of the copper mineral arrives at the surface in the form of large lumps of very pure quality, eminently suitable for sorting out by hand.The rich ore is tipped over a grizzly at the shaft bins; the oversize hand-picked, and the undersize bagged direct.

Jan 1, 1912

By M Armstrong, S J. Coward, A Galli

Mine management is often expected to make rapid evaluation decisions at different stages of projects based on limited and uncertain data. The challenge is exacerbated by having to distil technical complexity into a financial model that is usually designed to produce only one or two key indicators, eg net present value (NPV), internal rate of return (IRR). Mining is a complex environment with many sources of uncertainty ranging from sampling to economics. In order to optimise investment decision-making, an appropriately structured evaluation framework must be utilised. An evaluation framework should be designed to encapsulate and integrate the complexity across the evaluation cycle, ie sampling, resource estimation, mine planning and treatment, and financial and economic modelling. This complexity is diverse and ranges from sampling support, scale effects to understanding the impact of variability, uncertainty and flexibility on operational efficiency and economic viability. These complexities, combined with time and capital constraints, usually do not allow all facets of evaluation to be integrated into the model. The model must strike a balance between simplified estimation techniques and sufficient incorporation of aspects of the project that will make a material difference to the investment decision. This paper demonstrates the impact of the scale of measurement on the valuation of a mineral project. Comparisons are made between global estimation averages using a top-down approach and local estimates using a bottom-up approach. Three sampling campaigns were conducted on a virtual orebody to compare the relative NPV accuracies. Stochastic forward models were run on foreign exchange rates and are compared with the results from a fixed foreign exchange rate model.

Jan 1, 2006

The AusIMM/AMIC code for reporting Reserves seeks to improve the calibre of professional reporting on this subject. But have they gone far enough? Should the code appreciate that the degree of reliability of estimates required will vary with the type of mining planned? How does one "confirm continuity" as required by the code? The aim of optimum development drilling is to achieve appropriate ore zone definition for acceptable estimates of reserves and their economic extraction. Can this procedure be in conflict with the code? How does it affect finance decisions?

Jan 1, 1989

By R A. M Maddever, P Jeanneau, V Flahaut

Over the entire life cycle of a mine, from early resource evaluation to the blasting of benches, the collection of geochemical data is crucial for the site operator, who must routinely and intensively drill and sample the orebody. This produces huge numbers of physical samples, in turn requiring significant cost and time for their preparation and assay. Moreover, despite best efforts, the sample recovery process is prone to error, which limits the quality of data.The pulsed neutron gamma technique has been used for decades in various industries, in particular oil logging, for its ability to provide direct identification and quantification of elemental concentrations. However, its implementation in logging tools for the mining sector is relatively recent. Built around the latest in technology for optimal spectrometric measurement, a commercial tool referred to as FastGrade™ 100 has been available for a few years and used with increasing success in the mining environment, specifically the iron ore industry, resulting in a reduction in the amount of collected samples. Relying on the physics of neutrons and gamma photons, both of which are particles that penetrate the surrounding bedrock through several tens of centimetres, such spectroscopy tools measure in real-time the composition of a much larger volume than the delimited volume of the drilled material traditionally used for geochemical mapping. Better statistics and reliability of the estimated composition increase the ability to properly and quickly measure drilled holes and allow the substituting of all or part of the sampling and assaying efforts by geochemical log data. Our paper focuses on this technology, known as pulsed fast and thermal neutron analysis (PFTNA). It reviews the main drivers for the design of such a logging tool and discusses how the fundamental characteristics of the technology, in terms of neutrons and gamma interactions, translate into interpretation of the analytical output.CITATION:Jeanneau, P, Flahaut, V and Maddever, R A M, 2017. Iron ore benefits from neutron pulsed geochemical tools, in Proceedings Iron Ore 2017, pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Milner A, Brockway D, Hodges S

The combustion of brown coals in Latrobe Valley power stations produces approximately 500 000 tonnes of solid wastes each year. This material, which includes precipitator ash, char and furnace ash, is hydraulically sluiced to large ashing ponds and the supernatant solution is ultimately discharged to the sea. There are significant operational and capital costs associated with the current ashing system. The ash produced from the Latrobe Valley coals is unique and has a wide variety of potential applications including soil conditioning, concrete and cement extenders, fillers in non-metallic materials, components of building products. In addition, with the application of appropriate technology, it is possible to extract char, sodium sulphate, calcium carbonate and magnesium metal (as the chloride) in substantial quantities from the ash. Research has been carried out to explore the prospects of these various options for ash utilisation. The research has focused on detailed characterisation of the ash material and the potential extraction efficiency for various species under various conditions. From this work a conceptual process has been developed and subsequent studies have been directed towards understanding variables and optimising operating regimes for product extraction. Currently, the work is concentrating on the separation of char, the development of high-grade carbon products and the extraction of sodium sulphate.

Jan 1, 1992

Recently discovered Carboniferous bentonites are variable in charadeI and thickness, but being altered aeolian, ash-fall tuffs, they are probably extensive. Most are the Ca-montmorillonite type without the natural swelling characteristics of the Wyoming deposits, but their situation, thickness, and response to beneficiation through cation exchange may give them some potential as sources of future economic deposits.INTRODUCTIONLoughnan and See (1959) gave an account of bentonites and fuller's earth deposits of New South Wales. The most likely potential industrial sources were those occurring in the uppermost formations of the Newcastle and Singleton Coal Measures (Permian) in the Hunter Valley and deposited during epochs not marked by strong contemporary vulcanicity.One feature of the record of known occurrences at that time was the absence of bentonites from the thick volcanic sequences of the Carboniferous, but since this paper appeared, many bentonite beds have been discovered by the writer in the Carboniferous facies formerly known as the "Kuttung Series".The purpose of this contribution is to report briefly on the occurrence, genesis, mineralogy, and economic potential of these deposits which augment possible sources of bentonite near major industrial centres on the eastern seaboard.The potential world demand for bentonite would increase markedly with the trend to pelletization in the steel industry, if its use in this field became more general. More detailed mineralogical studies will be presented in later publications.STRATIGRAPHIC DISTRIBUTIONBentonite occurs at irregular intervals throughout a thick sequence of dominantly continental, plant bearing strata...

Jan 1, 1965

By Holla L, Tyminski A

Stowing has been successfully used in many countries as a means of controlling surface subsidence, minimi ing incidences of spontaneous combustion, maintaining gate road stability and maximising coal recovery.Australian experience in stowing is limited but in the future increased extraction of thicker and/or multiple seams by longwall operations and resolution of conflict of alternative land u'ses may necessitate the use of stowing in coal mining. At present there is little incentive for mining companies to introduce and operate a stowing system because costs have to be borne by the individual companies and benefits spill over to society and the State. Cost sharing by the industry and State incentives may overcome the problem of cost disincentive.

Jan 1, 1987

By Lonie W. M

The rapid development of the Australian steel industry over the past twenty years has greatly increased the demand for coking coal from the collieries owned by the Broken Hill Proprietary Co. Ltd. and Australian Iron & Steel Ltd. This in turn has called for an intensive and continuous programme of colliery expansion and new colliery development, along with the reorganization and modernization of existing collieries.This paper presents a general description of the factors involved and the techniques used in planning modern colliery development for the steel industry.PRELIMINARY GEOLOGICAL INVESTIGATIONSIn any colliery development, preliminary geological investigations require a detailed and practical knowledge of the geology and characteristics of the coal-field as a whole. In the early stages of the investigations, probably the most valuable information is obtained from outside the particular area under review, rather than within it, and unless the geology of the coal-field is understood, the projection of the known information into the unknown area cannot be carried out with certainty.Because development of the coal seams from the outcrops has been an apparently simple matter and not subject to the risks involved in deep mine development, the geology of the New South Wales. coal-fields has not received the attention that major mineral resources warrant.Only the most accessible regions of the coal measures have been generally prospected, while the potential areas remain...

Jan 1, 1957

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port Kembla steelworks of Australian Iron & Steel Pty. Ltd., vary in rank and in type over the Southern and South Western Coalfields.The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal.Plans of seam variation show the regional trends in rank and type for each seam.The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Seam in a zone embracing Bulli and Appin collieries.A satisfactory correlation is achieved between vitrinite content and coke stability and hardness, enabling prediction of coke strength for Southern Coalfield coals.The use of vitrinite reflectance, as an indicator of rank, in addition to type to predict coke strengths is at present hampered by lack of data, particularly in the South Western Coalfield. Nevertheless, data available at present allow the use of both variables and give better correlations with coke strengths than type alone.A spread of comprehensive data across both coalfields will enable advance assessment of cokes produced from coals having known rank and type. Blending to a ranktype specification for optimum coke strengths would allow the best use of the coal reserves of the coalfields.

Jan 1, 1969