Search Documents

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

The Nagambie heap leach gold mine commenced production of gold in September, 1989. The mine,120km north of Melbourne in Victoria, Australia, was developed by Perseverance Mining Cor- poration Ltd, a junior Australian mining company, with no other operating mines. Gold production to December 31, 1990 was 47,621 oz. The mine is now producing at the rate of about 45,000 oz per year. As of February 28, 1991, resources at the mine are 5.1 million tonnes measured, at 0.65g/t Au while reserves were 1.65 million tonnes at 0.86g/t Au of proven, heap leach ore, plus 0.37 million tonnes at 0.40g/t Au, of dump leach ore. Metallurgical recoveries expected are 80 per cent for the heap ore and 60 per cent for the dump ore. Perseverance Mining Corporation was listed on the Australian Stock Exchange on April 2, 1987, after a capital raising in March that year. At this time the company's issued capital was 4 million ordinary 25ó shares, 3 million of which were issued to the public to raise $0.75 million.

Jan 1, 1991

Near Kangiara in south eastern New South Wales, Australia, a number of polymetallic (copper, lead and zinc, with minor silver and gold) mineral deposits occur within a relatively broad volcanic rock belt, intercalated with limestones, sandstones and shales, of Silurian age. The Kangiara deposit was the most significant for the region.Adjacent to the Kangiara deposit, the unaltered country rocks are more rhyolitic than elsewhere in the volcanic rock belt, and the mineralization is accompanied by silicification, chloritization, sericitization and argillization. The host rocks typically contain a higher K20:Na2O ratio than the volcanic rocks not associated with mineralization.In the Kangiara deposit the mineralization consist of massive (in part banded), fragmental, disseminated and vein-type copper-lead-zinc ores, with the massive and fragmental types divisible into pyrite-rich, chalcopyrite-rich and sphalerite-galena-rich varieties. With respect to this mineralogy, the ore textures and sulphur isotope compositions the deposit can be compared to the stratiform mineralization associated with Silurian acid volcanic rocks at Woodlawn, Captains Flat and elsewhere in the Lachlan Fold Belt, as well as the Tertiary Kuroko deposits of Japan.

Jan 1, 1990

By Wang S

Fragmentation is the basic concern in rock blasting and serves as the main measure of blasting effectiveness. A good estimation of fragment size distribution before blasting is very useful and helpful for selecting the proper equipment for loading, transporting, and crushing rocks. A fragmentation model is presented that is based on a hole by hole analysis and correlates the rock properties, burden, spacing, and explosive column with the blasted volume and fragmentation obtained. The drill bench is divided into three separate areas corresponding to different breakage mechanisms. They are: 1) a main breakage or casting area, 2) a secondary breaking area, and 3) an overbreak area. The boundary of the main breakage area is found from the magnitudes of strains in the stress waves and the tensile strength of the rock. The secondary breaking area is determined by stress wave reflections at discontinuities and interactions between colliding stress waves from adjacent boreholes. The overbreak area is that beyond the main breakage area "where the reflected tensile waves no longer break the rock. This analysis is applied on a hole by hole basis to locate the breaking points. Then connecting the breaking points on each side of a borehole forms the triangle of the main breakage area. This is repeated for the next hole and the remaining area is the secondary breakage area. After the angle and area for each hole are found the Kuz-Ram model is used to predict the fragmentation size distribution for each hole. Then summing up the size distribution for each hole gives the total fragmentation distribution. This analysis has been successfully applied to field tests performed in a limestone bench where the entire spoil pile was screened to determine the fragment size distribution. Knowing the explosive and rock properties the breaking area was found for each hole, the strain and stress values, the breaking point, and angle of breakage (104 degrees). The fragmentation size distribution was then calculated and compared to the field data with excellent agreement.

Jan 1, 1990

By Woodcock JT

This paper deals with some innovations and current proposals for the treatment of gold ores and considers the possibilities of incorporating new developments in new or revised ore treatment flowsheets. The main topics considered are I. typical practice in relation to the size of gold particles, 2. concentration of coarse gold, 3. leaching reagents, 4. in situ leaching, 5. heap leaching, 6. carbon-in-pulp adsorption, and 7. treatment of complex ores (gold in pyrite, gold tellurides, and carbon-containing ores).

Jan 1, 1982

Through partnering with mining customers, DYNO has been able to develop some specific technologies that benefit blasting operations particularly in underground mining. Some of these areas are: 1. Cost allocation and product tracking systems; 2. Borehole video surveys of breakthrough blastholes; 3. Borehole video photography for logging VRM blastholes; 4. Toe-load uphole loading for sublevel cave mining operations; 5. 3D blast modelling for underground ring blasting. This paper outlines these developments in the context of a Canadian underground metalliferous mine.

Jan 1, 1995

By G R. Dickens, N H. S Oliver

The genesis of giant hematite ore deposits in northwest Australia remains a contentious topic in part because key evidence supporting a unifying genetic model has not been found at all deposits. In particular, several papers have proposed that carbonate replacement of silica layers in banded iron formation (BIF) by basinal brines is a requisite first step toward ore formation. This initial hypogene stage is inferred primarily from the presence of silica-poor, carbonate-rich rocks found below ore and along normal faults at the Mount Tom Price and Giles Mini deposits. However, until recently such rocks have not been identified at the largest martite-microplaty hematite deposit, Mount Whaleback. In this study, samples of the upper Mount McRae Shale are examined for their chemistry, mineralogy and petrography. These samples were collected from several key locations, including within drill core that penetrates an area immediately beneath ore along the Mount Whaleback fault at Mount Whaleback. Compared to unaltered black shale from Wittenoom Gorge in the north and altered black and red shale at Mount Whaleback, reddish-green shale below the Mount Whaleback deposit is significantly enriched in MgO and CaO and depleted in SiO2. Samples of this shale consist predominantly of fine- to medium-grained dolomite and ankerite cut by chlorite and carbonate veins, contrasting with unaltered equivalents that contain mostly stilpnomelane, K-feldspar and relatively minor carbonates. This alteration is distinct from assemblages developed during regional metamorphism, and possibly represents hydrothermal alteration after metamorphism. Although several questions remain unanswered, these results support models that invoke an early hypogene stage during the formation of the martite-microplaty hematite deposits in the Hamersley Province.

Jan 1, 2005

The intent of this address is to look forward into the 21st Century and present certain thoughts as to how underground coal mining might be conducted. The views in this talk are based principally on the author's experience with mining practices in the United States. It may be difficult to accept, but the 21st Century is a mere 12 years away. What new techniques will be available? To develop an understanding of the way in which technology has been and could be changing, a two- stage analysis is made of mining technology for U.S. Coal. The first phase covers the period 1975 to the present, while the second includes 1960 to 1975. This historical perspective includes a view of underground production by mining methods, considerations of labour productivity, and a review of accident and fatality rates. Several topics are important features of this historical analysis. Among the most significant are: (1) the introduction of Ion-wall mining technology into U.S. underground coal mines, (2) the use of computers to assist in mine planning and design activities, (3) major efforts to improve health and safety performance, with emphasis on underground dust control, and (4) improvements in mining equipment with an eye towards increased reliability and up-time performance. Based on that historical perspective, projections are made in three increments. The first being immediately at the turn of the century, the second being a dozen or so years beyond that, and the third being at the quarter point of the 21st Century.

Jan 1, 1988

By Wright D. J

Successful heap leaching depends on three major factors: 1. Chemical conditions appropriate for the dissolution of the valuable metal; 2. Contact between the leach solution and the valuable metal particles; and 3. Movement of the leach solution through, and out of, the heap. Given that appropriate chemical conditions can be provided, and the individual particles have sufficient permeability to allow solute/solvent contact, the problem of getting the solution to and from the particles remains. Non-uniform percolation of solution throughout the heap, caused by the presence of fines, is a common problem which occurs, to some extent, with all heap leachable ore. The conventional solution to this problem is agglomeration, which involves the attachment of fine particles to larger particles, effectively modifying the size distribution by preventing the fine particles from acting on their own. While agglomeration must be considered as an extremely effective technique with virtually no limit to its application from a technical point of view, its application is limited by economic considerations. A new technique has been developed which is not only a low cost alternative to agglomeration, but also has the potential for enabling the application of low cost heap and vat leach techniques to a significantly wider range of ores than current practice would suggest. The new technique, known as Electrokinetic Leaching, utilises electro-osmotic flow to enhance percolation through the heap. This paper describes and presents results of the laboratory testing, pilot heap operation and commercial application of Electrokinetic Leaching of a low grade gold ore and a tailings deposit. Comparative cost analyses between conventional and the alternative processing techniques are presented.

Jan 1, 1994

By d&apos, Alton AJ, Rigden DT

Modern petroleum refining offers a complexity of environments, each requiring different metals for the satisfactory performance of-the various sections of the refinery, and this paper first outlines the varied enva.x¦on-ments thus met.It follows that the metal types in use will also vary to suit each particular environment, and the paper' consequently covers the use of ferrous-metals, ranging from plan carbon steels to the high alloy types and the non-ferrous metals, particularly copper and its alloys.The failures of some,of these metals and alloys are then illustrated by experiences it Kwinana. These failures are duo to (a) corrosion, (b) erosion, (c) faulty welding, and (d) mechanical defects,' of which the first is by far the most prevalent. The protective measures taken to prevent subsequent failures are then given under one or other of the following headings :(1) alterations in process conditions, (2) the use of alternative ,alloys,(3) suitable heat treatment, (4) redesign of the failed section, (5) cathodic protection, and (6) use of corrosion inhibitors.Reference is then made to the use of specialised metals and alloys.Metals, generally in the form of oxides or salts, are also used as catalysts in refining processes. Activated alumina is used, combined with silica .forScracking' of heavy oils, and as a support -for platinum, cobalt, molybdenum, nickel and similar metals, which catalyse hydro-genation and dehydrogenation-processes. .In the final formulation of petroleum products metallic compounds may be added. Reference is made to the large quantities of lead used by the petroleum industry and to the use of metallic soaps and detergents in the formulation of lubricating oils and greases.

Jan 1, 1962

By E M. Rykaart

The design of soil covers as part of the remediation initiatives for mine waste facilities is common practice and more and more engineers are faced with designing these facilities. The design issues associated with these soil covers are complex and requires a good understanding of unsaturated flow. More engineers are making use of numerical models to predict how cover designs would perform, and this has been necessitated by the high non-linearity associated with solving unsaturated flow problems. There are numerous numerical models available to the prospective users and they are all simplifications of reality using different assumptions. The users of these models often do not understand the limitations of the models but rather select a model based on ease of use, and that lends to increasingly erroneous designs being proposed for construction. This paper describes a comparative evaluation of a cover design using four different codes available today; SoilCover, SWIM, HYDRUS-2D and HELP. The paper does not propose to measure these codes up against each other and make statements about which is better than the other but rather illustrates how the assumptions in each code affect the outcome. The data set used for the comparative study is a well calibrated data set that that has been collected over a long period in time and that has been collected according to strict controls. The authors present the pitfalls of numerical modelling of the surface flux boundary conditions, as well as present guidelines towards appropriate use of these modelling tools.

Jan 1, 2003

By Iley J. D

The production of zinc from low grade concentrates, particularly those high in iron, has a poor economic return due to a combination of higher concentrate transport costs, increased processing costs and an increased cost for disposal of iron residues. The production of iron-bearing residues from the electrolytic zinc process is also seen as undesirable for both cost and environmental reasons. This paper details the pilot plant testwork conducted at the Pasminco Research Centre in conjunction with Minproc for the production of zinc oxide fume from a high-iron zinc sulphide concentrate from Colquiri in Bolivia. The concentrate is derived from a tailings retreatment operation and has a high iron content (40 - 45 per cent Zn, 14 - 17 per cent Fe) due to the presence of marmatite. Pilot plant trials were conducted using the slag bath reactor at Pasminco Research Centre at rates up to 500 kg/h of pelletised zinc concentrate, using a natural gas/oxygen-enriched air lance. The fume produced averaged 76 per cent Zn at recoveries up to 96 per cent and was recovered in a baghouse after gas cooling. The iron was oxidised into a fayalitic slag that passed the TCLP test (toxicity characteristic leaching procedure) and the sulphur was oxidised to produce a high SO2 gas which would be suitable for sulphuric acid production. The process produces a zinc oxide fume that can replace calcine as a feed for electrolytic zinc plants. The iron reports to a stable slag for disposal, thus eliminating the need for its disposal as jarosite from the leach plant. Only a simple leaching operation on the fume is required as there is no zinc ferrite present.

Jan 1, 1993

By Moyes A. J

The Intec Copper Process uses a strong chloride electrolyte at atmospheric pressure and 80 - 85¦C to produce high purity, 99.99 per cent copper granules and elemental sulphur. A recent, exhaustive study by an independent, major Australian corporation has shown the capital cost of an Inter plant to be approximately half that of a copper smelter at the 200 000 tpa capacity level and approximately half the operating and capital cost at the 50 000 tpa level. The Inter process costs were also shown to be greatly superior to the best available leach/SX/electrowin technology. The process utilises a multi-stage counter current leach at 80 - 85¦C with the addition of air at atmospheric pressure to precipitate iron as a goethite type compound, followed by a two-stage purification process separating impurities in metallic- and other forms. Purified cuprous chloride/sodium chloride solution is fed to an electrolytic diaphragm cell where high purity copper granules are produced at current densities of 1000 - 1500 A/m2 withoutthe need for conventional electrode stripping. Power consumption is approximately half that of the cupric route. The product is suitable for the direct powder metallurgical conversion of the granules to products such as wire or strip. All the steps in the 'furnace free' conversion of copper mineral to product have been demonstrated The process can treat low grade and contaminated concentrates without penalty, thereby offering greater returns to the miner. Lead, zinc and silver may be recovered as metals, with the high oxidation potential of the electrolyte allowing extraction of gold at high efficiency. The gold is selectively precipitated on activated carbon with negligible copper and silver contamination.

Jan 1, 1992

The authors have succeeded in providing additional rigour and clarity to the formulation and execution of the dynamic programming algorithm for optimum open pit limit determination. The inclusion of the blocks on the J + 1 column in the search for Pmax, and constraining this search with blocks assigned a value of negative infinity, ensures an optimal solution within the defmed blocks. The effect of the negative infmity blocks is to preclude mining along the diagonal blocks from the first row that they occur in. Figure 1 graphically illustrates the effects of this on the calculation of P. A practical application for constraining mining with negative infmity blocks is the case where the pit outline is defined by lease boundaries and not by the value of blocks to be removed. Any legal, social or physical constraint could be accounted for in the same way.The danger in applying this technique is that the negative infinity blocks will override any other more profitable solutions that may exist. This is in fact what has happened in the example that the authors use. If a further column is added to the left hand side (column -1) and the calculation is carried out again, a more optimal x-section can be found. (If the negative infinity values are removed the same result is obtained.) This gives a pit value of 112 as against the 108 of the authors' optimal pit. This calculation is shown in Figure 2. Lerchs-Grossman optimization is reliable only if there are sufficient columns available to allow "mining" to optimum depth of the ore body and still allow the pit to break out at the surface within the confines of the columns.This author's approach is to create enough columns each side of the lateral limits of the ore to allow the pit to intersect the surface while still within the confines of the block model. Implementing the methods discussed by the authors helps to reduce the number of columns required to achieve this.

Jan 1, 1987

ON milling plants, where a large number of slime samples are collected each day, considerable work is involved preparing them for the assayer. The usual practice (as the material usually passes a 150-mesh screen) is to place the sample on a 30-mesh screen an 1 brush it through on to a cloth below. The sample on the cloth is mixed and a portion taken out for the assayer. A simple apparatus that would rapidly disintegrate and prepare these slime samples for the assayer was needed. The manufacturers of assayers' supplies appear to have overlooked apparatus for this class of work. To overcome the tedious preparation of slime samples by the above method, the writer devised the apparatus shown in the accompanying drawing (Fig. 1). It will be seen that the apparatus is a combination of a modified household flour sifter and a riffle sampler.The apparatus is made up in two parts, the top half consisting of a screen box carrying the disintegrator, and the bottom half a, riffle divider, the joints between the two being a slip-in fit. A lid is provided for the screen box. The disintegrator consists of an open drum, to which are soldered three rows of spring steel fingers. Each row has a number of steel fingers which, on rotation, press against the semi-circular screen in the screen box, forcing the slime particles through.To operate the apparatus an 8-in. sample tin is placed under each spout of the divider. The sample of slime, which is about 2 lb. in weight and usually in lumps, is placed in the screen box, the cover replaced, and the drum rotated about half-a-dozen times by means of the handle.The disintegrated sample is divided by the rifle divider into two portions, which are found in the tins under the spouts of the apparatus. One of these samples is taken, mixed on a sheet, and sent to the assayer.

Jan 1, 1922

By Ormsby W. R, Farrar L

The stratigraphy of the central Pine Creek Geosyncline has been simplified into a three-fold subdivision comprising the Batchelor, Frances Creek and Finniss River Groups. The Batchelor Group consists of a sequence of shallow water coarse clastics and crystalline carbonates and is conformably overlain by the marine carbonaceous shale dominated Frances Creek Group. Interbedded within the carbonaceous shale are turbidites, iron formation, tuffs, carbonate and non carbonaceous shale. The Finniss River Group is a flysch sequence of greywacke and mudstone. The stratigraphic and structural evolution and igneous history are all interrelated. Although the Batchelor Group may have formed in a tensional regime, it is likely that regional compression and accompanying thin skinned deformation began during deposition of the Frances Creek Group. Continued compression resulted in D2 folding d6collement deformation, wrench faulting in compressional zones and thrust faulting. Occasional relaxation of compression is marked by a number of periods of basic intrusion and perhaps distal volcanism. The style of deformation within sediments varies away from granitic basement highs and is similar to that observed around salt domes and found in experimental diapiric models. Sedimentary facies changes also indicate local emergence of basement highs during sedimentation. As compression continued, the deposition of thick sequences of the Finniss River and El Sherana Groups brought about regional metamorphism. Relaxation of compression and waning of associated subsidence resulted in a relative increase in the rate of uplift and partial melting of diapiric sialic basement. In places, granitic magma moved upwards and crystallised forming grossly concordant bodies. Other masses moved laterally and formed extensive granitic sills. Later compression periods caused mainly brittle deformation which may have been strongly influenced by underlying basement fabric.

Jan 1, 1994

By E Whiteman, L Reyneke, H Horsch

Heavy mineral sand deposits are a source for the economically important element titanium, which is contained in minerals such as ilmenite and rutile. In heavy mineral deposits ilmenite displays various degrees of alteration. Natural weathering of ilmenite involves the removal of Fe and thus results in an increase in the Ti-content. Minerals such as pseudorutile, ferropseudobrookite, anatase and the ill-defined mineral aggregate leucoxene, which consists mainly of various amounts of remnant ilmenite, pseudorutile, ferropseudobrookite and anatase, are typical replacement products of ilmenite. Ferropseudobrookite occurs as a recrystallised, optically and chemically distinct mineral phase. Textural relationships suggest a diversity of physicochemical conditions including weathering and metamorphism that led to the formation of complex mineral assemblages and textures. In the heavy minerals industry the alteration products of ilmenite are generally referred to as æaltered ilmeniteÆ and/or leucoxene. The distinction between æaltered ilmeniteÆ and leucoxene is not consequently defined and is very much dependent on economic factors and specific mining operations (ie determined by deposit specific mineral assemblages). Generally the term leucoxene is used in the heavy minerals industry as a collective description for ilmenite alteration products with TiO2-components ranging from 65 - 95 per cent. A detailed comparative mineralogical investigation including microscopic, SEM and QEMSCAN« techniques show that it is possible to identify and quantify the replacement products of ilmenite on a micron scale. QEMSCAN« generated particle maps were graphically compared with photomicrographs taken by applying reflective light microscopy. The resulting information can be integrated over the entire sample with respect to composition, absolute and relative mineral abundances, grain sizes, volumes, densities, textural relationships and liberation potentials. This provides a powerful tool for a first appraisal of the physicochemical behaviour of bulk samples and individual particles during metallurgical processing.

Jan 1, 2008

QEMSCAN« technology is a widely accepted automated e-beam technique providing quantitative and statistically robust mineralogical data to the mining industry. It uses X-ray mapping combined with backscattered electron (BSE) brightness to identify minerals in almost any type of geological material (Gottlieb et al, 2000). Besides the modal mineralogy also the liberation, associations, average grain size and other textural information can be obtained. The aim of this study is to test reproducibility of this technique by setting up and running standard tests on different QEMSCAN« systems. Multiple sample blocks were prepared by our standard operating procedure as epoxy-mounted, carbon-coated, polished blocks. The replicates were measured under the same conditions and measurement parameter settings on different QEMSCAN« instruments. The relative standard deviation (RSD) for the set of measurements was calculated. Generally the reproducibility of the systems themselves was found to be excellent, ranging between 0.4 and 1.5 per cent RSD. The more significant change in the reproducibility was found to be caused potentially by the sample preparation and variation in the mineralogy of the replicates. The measurement parameter settings together with these variations can account for almost 15 per cent RSD for minerals of low abundance. For analysed samples good results for the main phases present in quantities higher than 2 - 5 wt per cent of the total mass of the sample were confirmed with RSD generally below six per cent. Following the experiments, the parameters having the biggest influence on the performance of the QEMSCAN« and its precision are discussed in detail. The importance of sample preparation procedures and measurement parameter settings is emphasised. It is shown that experience and excellence is necessary for getting the most from the automatic mineralogical methods like QEMSCAN«.

Jan 1, 2008

By R H. Boffey

The Osborne copper-gold deposit was discovered in North-West Queensland in 1989. Underground production activities commenced at Osborne deposit in April 1996. This paper will examine technical and operational aspects of the underground mine during its development to a 1.2 Mtpa operation . Technical aspects discussed include geology, mine design and mining methods, equipment fleet selection and capital infrastructure. Operational aspects discussed include the evolution and performance of the integrated work teams that are utilised at Osborne to perform all mining and maintenance activities.

Jan 1, 1998

By J-S Zhang

In this paper, the author briefly introduces the resource characteristics of Chinese iron ore, as well as the present increasing market demand for iron concentrate. The SHP-3200 wet high-intensity magnetic separator (HIMS) is used to separate complicated weak-magnetic iron ores being composed of specularite, limonite and siderite in Jiuquan Iron and Steel (Group) Co Ltd. Some technologies have been used to improve SHP-3200 HIMS, including modifying the angle of magnetic polar from 90¦ to 83¦, cooling the exciting coils by oil instead of air, adding reverse-washing equipment to wash off magnetic particles and adjusting the tooth-space of the matrix from 5.0 mm to 3.5 mm or 2.5 mm to enhance the recovery of fine particles. It is still difficult to meet the requirement for recovering more difficultly separated iron and the demands for high-grade concentrate of iron. In order to improve the recovery of difficult-separated iron, the film-magnetic separation technique is applied into the HIMS and a new LY matrix is designed to form magnetic gradient vertically. A flowing-film feeder is also added and the feed mouth is modified to make a slurry flow formed in the form of film along the wall of matrix. The microstructure and dissemination character of the mineral particles is studied, and the specific susceptibility of the primary minerals is measured. Then the distributive characteristics of a magnetic field for the separator with film-magnetic technique and the motion of particles in the process of separation are all analysed. By introducing the film-magnetic separation technique to SHP-Φ700 HIMS, the recovery of iron can be raised from 69.45 per cent to 76.07 - 78.96 per cent with the similar grade of concentrates of iron. Such an increase of 9.51 per cent in the recovery also shows that it is feasible for such film-magnetic separation technique to be applied into HIMS.

Jan 1, 2005